Search Documents

By C. W. Allen, L. C. Moore

The Mather mine, of the Negaunee Mine Co., is within the limits of the City of Ishpeming. on the Marquette iron range in Michigan's Upper Peninsula. It is named for William G. Mather, who has served as President, and Chairman of the Board, of The Cleveland-Cliffs Iron Co. for well over 50 years. The property comprises nearly the square mile of section 2, T.47 N. R.27 W., which, except for 20 acres in the northeast corner, was leased by The Cleve-land-cliffs Iron Co. to the Negaunee company. The latter is a partnership of Cleveland-Cliffs and the Bethlehem Steel Co., organized to equip the property, retaining Cliffs in charge as operator. Shipments of ore from this area are mainly through Marquette, which is 16 miles to the northeast on Lake Superior, or through Escanaba, a Lake Michigan port, 65 miles to the south. Cleveland-Cliffs, in 1943, operated 12 mines in the Lake Superior district, with shipments of 6,635,576 tons for the year. Geology The north footwall of the Marquette Range synclinorium outcrops near the north line of set. 2, the iron formation dipping to the south at an angle of about 40. The south side of the trough reappears at a distance of 4J5 miles on sec. 26 and the surface geology between shows iron forma- tion or intrusive diorites. The latter are harder than most phases of the iron formation and, as a result of glacial action, appear as buttes or low-lying hills. The general elevation of sec. 2 is about 1450 ft. above sea level, or 850 ft. above Lake Superior, and the higher diorite outcroppings about 1600 ft. above sea level. The geological structure has been complicated by a series of major and minor faults, one of which may be illustrated by the diorite sheet, which tilts south with the iron formation in the north half of the section and then reappears near the center to repeat this sequence. Sectionally the geological series includes a nearly eroded capping of Goodrich quartzite followed by the considerable thickness of Negaunee iron formation, which is cut by intrusive dikes or diorite sheets, and underlain by the Siamo slates grading into quartzites. The ore deposits occur mainly in troughs formed by the intersection of impervious dikes and the footwall slate, but include locally enriched lenses or bands in the iron formation and also interbedded with the Siamo slate. The ore is a soft red hematite with an indicated dried analysis from the surface drilling to date of 61.50 per cent Fe, 0.134 Per cent P, 5.40 per cent Si, 2-87 Per cent A1 and 0.015 per cent S. Exploration A diamond-drilling campaign started in 1937 actually had its inception in 1917, when a number of shallow test holes were put down for the purpose of locating ore that might be quickly developed and mined

Jan 1, 1946

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

By R. Philip Hammond

Monazite has had a Cinderella-like history. Although nearly go per cent pure rare-earth compound (rare-earth phosphate) it was sought at first not for the rare earths but for the sake of a minor constituent—thorium. The thorium, essential for the Welsbach gaslight mantle, was present in only small quantities and the principal constituents, the rare earths, were largely discarded. Gradually, however, the rare earths have developed uses of their own and today have left the thorium far behind in value. Occurrence Monazite was first produced commercially about 1886, in North Carolina, where it was collected in small sluices by farmers who found it in stream beds on their land. The deposits were later exploited on a larger scale, but were mostly abandoned in a few years, when monazite from Brazil came upon the market in far larger quantities. Domestic production ceased entirely in 1906. The Brazilian source is still active, together with Indian, Dutch East Indies, and Australian deposits. Several other localities in the United States have yielded monazite, but none of these has produced commercially as yet. Monazite occurs originally in pegmatite~ and gneisses, through which, unfortunately, it is scattered in highly dispersed form. All commercially useful deposits consist of transported monazite sands liberated by erosion and concentrated by the action of water, which has sluiced away lighter materials and concentrated the heavy (D = 5.0 to 5.2) grains of monazite, together with ilmenite, zircon, garnet, and other dense minerals. The Carolina deposits were in stream beds; most of the other deposits mentioned are on or near the seashore, where the action of the waves has served to concentrate the monazite. In most cases today, the sands are worked to obtain the ilmenite and zircon, as well as monazite. The minerals are separated by means of sluices, dry tables, and magnetic separators, and each is finally obtained nearly pure. No crushing or grinding is necessary. The concentrates are shipped in fiber bags. Composition of Monazite As Table I illustrates, monazite is the anhydrous orthophosphate of the cerium Table i.—Typical Analysis of a Monazite Sand (India). Per Cent Thorium oxide............................. 8.1 Cerium oxide.............................. 30.6 Lanthanum oxide........................... 15. 7 Neodymium oxide.......................... 10.5 Praseodymium oxide........................ 2. 9 Samarium oxide............................ 1.0 Europium. gadolinium, and terbium oxides.... 0.7 Yttrium oxide.............................. 0.4 Dysprosium, holmium, erbium. thulium, ytterbium. and lutecium oxides................. 0. 1 Silicon oxide............t................... 2.4 Calcium, aluminum, and iron oxides.......... 1.0 Uranium oxide............................. 0.3 Phosphorus pentoxide....................... 26. 2 a The values given for the rare earths following samarium are approximate. being based upon analyses of concentrated fractions derived from monazite. The composition given represents Travancore monazite carefully freed from other minerals. goup of rare-earth elements. A small amount of yttrium and terbium group phosphate is also present.* All the rare-

Jan 1, 1948

Jan 1, 1968

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By T. Suganuma

Mitsubishi-Cominco Smelting Co. is a joint venture of Mitsubishi Metal Mining Co. Ltd. (M.M.M.) of Japan and Cominco Ltd. of Canada. The smelter, which is located alongside M.M.M.'s Naoshima copper smelter, was completed in May, 1966 and has a capacity of 36 000 metric tons per year of refined lead. The concentrate feed for the smelter from Pine Point Mines Ltd. is high grade with low impurities; particularly silver, bismuth, antimony, and arsenic, which facilitated a simple plant layout and operation. Concentrate, fluxes, recycle granulated slag and return sinter are drawn from bins by automatic control over weigh belt feeders, sintering is carried out on a 20 m2 Lurgi updraught sintering machine, furnacing in a 3.0 m x 1 ½ m water jacketed blast furnace equipped with an Asarco continuous tapper, refining in four 120 metric ton kettles and casting on a 25 metric ton/hour automatic casting machine. The S@ gas from sintering is cleaned in a high temperature baghouse utilizing glass bags and is then delivered to the M.M.M. copper smelter acid plants. The furnace gases after cleaning in a low temperature baghouse are vented to atmosphere.

Jan 1, 1970

By D. B. Crouch, D. A. Poulter

The engineering and metallurgical assessment of the McLaughlin Project ore body concluded that an open-pit mine and cyanide leach mill process would be feasible, producing both waste rock and residual mill tailings. As a part of the planning and permitting process, site selection studies were conducted for the tailings and waste rock disposal. The site selection process began with a regional identification of potential disposal sites and proceeded through 1) regional screening, 2) elimination of sites with obvious fatal flaws, 3) qualitative ranking of site evaluation criteria, 4) quantitative ranking of sites, 5) field investigation, 6) evaluations of field data, and 7) selection of preferred sites. Based on this approach of site rankings and field evaluations, tailings and waste rock disposal sites were selected and recommended for the preliminary design phase of the permitting and project development process. The site selection study provided the documentation necessary to justify the use of these sites for waste disposal and enabled Homestake Mining Co. to anticipate and integrate environmental concerns with agency requirements into the planning process.

Jan 1, 1986

Tile National Research Council announces further appointments to National Research Fellowships in physics and chemistry. The object of the National Research Council in maintaining a system of research fellowships is to promote fundamental research in physics and chemistry primarily in educational institutions in the United States. Fellowships are awarded to persons who have demonstrated a high order of ability in research for the purpose of enabling them to conduct investigations at educational institutions which make adequate provisions for research: in physics and chemistry. The new appointments are as follows: In Chemistry.-Warren C. Vosburgh, of New York City, B. S. Union College, 1914, A. M. Union College, 1916, Ph. D. Columbia University, 1919. Research assistant to the Professor of Chemistry at Columbia University for the past six months. George Scatchard, of New York City, A. B. Amherst College, 1913, Ph. D. Colt tibia University, 1917. Formerly research assistant to the Professor of Chemistry at Columbia University and instructor in organic chemistry: First Lieutenant. Sanitary Corns. U. S. A.

Jan 7, 1919

Adolph Greiner, Seraing, Belgium:—I have nothing special to add to Professor Hubert's paper except to say that there are some little things that it would be well to have corrected when the paper comes to be published. In dealing with the thermal efficiency of the engine, you will find that the 29.84 per cent. was a very high one. Professor Hubert has forgotten those engines built under the Cockerill type, but he has referred to them in Appendix 11. At our works at Cockerill we have built 63 engines, giving 63,000 h.p., and the other companies who have received licenses have built 113 engines, making 103,000 h.p., and aggregating 176 engines and 166,000 h.p. Eight years ago I had the pleasure of giving to the Institute the results obtained up to that time. Since then a good many engines have been constructed. In 1898 I thought a blast-furnace producing 100 tons of pig iron would allow 3,000 h.p. Professor Witz and Professor Hubert show that with the same production of pig the new engines take 3,800 h.p. out of the gas. At present at Cockerill we make 700 to 800 tons of pig iron per day, and we hope to have 26,000 h.p. in a few years. At present we have only half of that in gas-engines, but we hope to have in five or six years all the gas out of these furnaces to the number of 25,000 or 26,000 h.p. Tom WEstGarth, Middlesbrough, England :—My contribution is not a paper in the ordinary sense of the word, because I am sure you will agree with me that what I have written is only supplementary to the other two papers. The notes are schedules of the larger-size gas-engines built by British engine-makers, of 500 h.p. and upwards. If you look at the schedules you will find that in England gas-engines have become quite ordinary motors for a good many purposes. It was at first thought that gas-engines were troublesome, and ill-

Jan 1, 1907

By R. E. Radabaugh, J. M. Brown, J. S. Merchant

The Gilman district is on the northeast flank of the Sawatch Range in central Colorado. It has yielded a total of 10,000,000 tons of ore having a value of over $250,000,000. Paleozoic sediments intruded by a Tertiary quartz latite sill and unconformably overlying Precambrian intrusives and metasediments comprise the country rock of the area. The sediments strike northwesterly and dip 8° to 12° northeasterly. Structures in the Precambrian are related to the Homestake shear zone of the Colorado mineral belt. Only minor folding and faulting occur in the sediments. The principal ore bodies are massive sulfide replacement deposits in carbonate rocks. They consist of long, pipe-like mantos in the completely dolomitized Mississippian Leadville Limestone and funnel-shaped chimneys of copper- silver ore cutting across the Mississippian and Devonian strata. Mineralization is continuous from the chimneys into the mantos. The principal ore bodies are roughly in the shape of a four-tined fork which points up dip. Smaller manto deposits occur in the Cambrian Sawatch Quartzite, and fissure veins are present in the Precambrian rocks. The principal minerals in the mantos are marmatite and galena in a gangue of pyrite and manganosiderite. The chimneys consist of a central core of pyrite with erratically distributed chalcopyrite, tetrahedrite, freibergite, and occasional galena with a shell of zinc ore on the outer margin. Both the chimneys and the mantos are surrounded by imperfect shells of manganosiderite and sanded dolomite. The mineralization is of Laramide age. Hydrothermal alteration affects all rock units to varying degrees. Clay mineral alteration halos occur around the ore bodies. Hydrothermal solutions have developed sanded rock, rubble filled channels, and banded zebra textures, principally in the Leadville Limestone. Structural control of the ore bodies is not well defined. Both the location of the district and the chimneys are probably related to basement structures. The mantos are largely controlled by stratigraphic factors and a pre-Pennsylvanian karst topography in the Leadville Limestone, which were modified by hydrothermal activity, and by weak zones of northeasterly trending faults.

Jan 1, 1968

By William R. Webster

In view of the great interest now taken in the tests of castiron and details of foundry practice, with the number of investigators at work, and recent improvements in the methods of research, it would seem that the time is ripe to attempt the solution of some of the many problems with which iron founders have to contend. Recent papers and discussions on these subjects* have opened up s large field for investigation, and have emphasized the importance of many considerations generally overlooked. With the view of promoting a comprehensive and systematic discussion, I have attempted to tabulate, in conveilient form, some of the most important points for investigation, on the general plan suggested, with such good results, by our former President, H. M. Howe, for the discussion on the Physics of Steel, at the Virginia Beach meeting, last year. This table can, no doubt, be modified or enlarged to advantage, and put in shape to serve as a guide or reminder to all who are interested in this line of work. Suggested Lines for Discussion and Investigation. I.—Correspondence between chemical composition and melting point, fluidity, shrinkage, fracture, chill, micro-structure, and other physical properties. II.—Influence of: I. Cupola mixture, use of steel and other scrap, oxidized or clean material, 2. Manner of melting, flux, etc., 3. Casting temperature, A. Fracture. 4. Manner of handling melted metal and B. Micro-structure. method of casting, C. Physical properties. 5. Size and form of casting, D. Shrinkage. 6. Kind of mould, green sand (under dif- on 1 E. Chill. ferent conditions of ramming, amount F. Residual stress. of moisture, and skin-dried), dry sand, G. Condition and quan loam, and chills, tity of carbon and 7. Rate and mode of cooling castings, other elements. 8. Manner and temperature of heating for annealing, 9. Additions of nickel or aluminum,

Jan 1, 1896

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,' conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By William F. Boericke

THE Christy Creek clay mine of the General Refractories Co., in the Olive Hill District, ranks with the most important producers in the north-eastern Kentucky fire clay field, both from production of high-grade flint clay, as well as unusual extent and thickness of deposit. The property is but one of a number controlled by the General Refractories Co. in this district, but is given first consideration among them by the operating staff. Its total area is over 5000 acres, owned in fee or by lease of clay mining rights, and although mining operations have been in progress for over five years, scarcely one per cent of the ground has been worked as yet. The mine is near the southwestern end of the clay field, which extends in a belt 12 miles wide and 55 miles long, in a southwestern direction from Kenova, W. Va., which, as the name indicates, is at the junction of Kentucky, Ohio, and West Virginia. Olive Hill, where there is one of the l1Ulin plants of the General Refractories Co., and to which the clay from the mine is shipped, is about 26 miles distant from the mine. Connection is made with the Chesapeake & Ohio R. R. by a spur line . 8 miles in length, owned and operated by the company.

Jan 1, 1929

By Norman Weiss

THE need for more efficient utilization of labor in the metal-mining industry has been the subject of several recent editorials in the mining press, and one attractive possibility for such improvement lies in the designing of future milling plants particularly with economy of man-power in mind. We are accustomed to think of mill design as the selection and coordinated arrangement of process equipment, but if labor is to be efficiently utilized it must be given early consideration in planning the new mill. There are three good reasons for economizing in labor: (I) to reduce costs, not only in the form of wages but also in housing, hospital, welfare, and other obligations that a company accepts when a new man is added to the payroll; (2) to prepare for recurrent periods of manpower shortage, during which a well-designed plant can manage to get along with skeleton crews; (3) because a milling plant that must depend upon an inordinately large labor force for its operation and maintenance is certain to be inefficient in other respects, for many of the shortcomings in design that make necessary the excessive use of labor are generally not corrected merely by having too many men. A simple example of this is a poorly designed ore-feeding system: if this is inadequate to the extent that one man must be constantly unclogging feed chutes, it may help the situation to put two men or three at this task instead of one, but the feed rate will still be inconstant. First of the factors that affect labor saving is the location of the mill. This is often determined by transportation costs alone, and as a result the mill may be placed close to the mine regardless of the nature of the terrain. The designer must then adapt his layout to the conditions, favorable or not. This happens often at small properties, where capital investment may seem more important than operating expense. In most instances, however, a mill site carefully selected for the advantages it gives the designer in laying out the plant is the most economical in the long run, even if it involves a slight increase in cost of ore haulage. Given some freedom of choice, the design engineer may be able to find just the piece of ground that provides the proper gradient for the needs of the flowsheet, permits installation of essential yards and trackage, and perhaps supplies an excellent site for a tailing dam. Further justification for having placed the mill not too close to the mine sometimes emerges only years later as an opportunity to treat ores from other properties. When it is known from the beginning that the new mill will serve a number of scattered mines, a free choice of mill site is naturally stimulated. The most important single factor in limiting the labor requirements of a mill is its materials-handling system for bring-

Jan 1, 1946

By Gilbert Soler

PRODUCERS of alloy steels recognize the importance of chemical composition in rela-tion to the hot-working properties and the typical surface defects found in their prod-uct. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization character-istics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures as well as the tendency toward scale formation and decarburization, This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative impor-tance of these factors in relation to the hot-working properties and surface charac-teristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel.

Jan 1, 1940

By J. W. Downey, A. E. Dwight, M. H. Mueller, H. Knott, R. A. Conner

Sixty new ternary equiatomic compounds are reported with a hexagonal crystal structure that is isostructural with or very similar to Fe2P, D3h-P62m. HoNiAl is a typical example, with a, = 6.9893 ± 0.0003Å, C, = 3.8204 ± 0.003Å, and c/a = 0.54 7. Three holmium atoms occupy (g): x,0,1/2 three aluminum atoms occupy (f): x,0,0; one nickel atom occupies (b): 0,0,1/2; and two nickel atoms occupy (c): 4, + , 0. The nonequivalent 1(b) and 2(c) sites give rise to two sets of unequal interatornic distances (i.e., Ho-Ni and Al-NL in the case above), which account for the prevalence of Fe2P-type tertmry compounds and the scarcity of binary examples. Unit-cell constants are presented for the sixty compounds and density measurements on the compounds HoNiAl and UFeGa confirm that three formula weights are present per unit cell. Neutron and X-ray powder diffraction intensity measurements were made on CeNiAl and HoNiAl, respectively. The atomic posiLiotml parameters in CeNiAl were determined from neutron data to be x = 0.580 5 0.001 for cerium and 0.219 5 0.001 for aluminum. An investigation of the quasibinary section between the binary compounds CeNi2 and CeA12 revealed a new ternary compound CeNiAl. The compound has a hexagonal structure and is isostructural with the prototype compound Fe2P. Additional examples discovered or confirmed in this investigation provide a total of sixty ternary compounds that are isostructural with or closely related to Fe2P. Previous investigators1'2 reported the unit-cell constants for the hexagonal compounds UFeA1, UCoAl, UIrA1, ZrNiAl, ZrNiGa, HfNiAl, and HfNiGa and the present investigation has confirmed that the compounds are isostructural with Fe2P. Independently, Steeb and petzow3 reported the same structure type for UCoAl, UIrA1, and UNiA1. However, the present results suggest a different atomic site occupancy for the component atoms in the three compounds. A detailed investigation of the relative positions of the three kinds of atoms in the compounds CeNiAl and HoNiAl will be discussed. EXPERIMENTAL PROCEDURE The equiatomic alloys were prepared from elements of 99.9+ pct purity by arc melting under a helium-argon atmosphere. After homogenization at temperatures from 700" to 900' C, a metallographic examination was performed by conventional methods, and density measurements were carried out by the immersion method in CCl4. A powder sample was prepared for diffraction studies by crushing a portion of the annealed button. X-ray diffraction patterns were obtained with a Debye-Scherrer camera, in which the annealed powder was glued to a quartz filament, and indexed with the aid of a Bunn chart. Unit-cell constants were calculated from the computer program of Mueller, Heaton, and Miller4 and d spacings were obtained by the program of Mueller, Meyer, and Simonsen.5 The intensity values were calculated from the relation I, ~ (m)(L.P.)F2 by a computer program written by Busing, Martin, and Levy.6 The absorption and temperature correction factors were neglected. An X-ray study of HoNiAl was carried out to take advantage of: large differences in atomic scattering factors for holmium and aluminum, X-ray patters free of background darkening, negligible oxidation at room temperature, and negligible weight loss in the preparation of this alloy. The neutron diffraction studies were made on a powder sample of CeNiAl contained in a -in. diam V tube and a pattern was obtained with neutrons of wavelength The neutron scattering factors employed (x 10-12 cm). In contrast to the scattering amplitude for X-rays, cesium does not have the largest cross section, however, there is a sufficient difference in the neutron scattering amplitudes to distinguish between the atomic species. The neutron transmission was high, 86 pct; therefore, absorption corrections were not necessary for the cylindrical sample. Most reflections could not be observed individually, because of the relatively large unit cell (a = 6.9756 and c = 4.0206Å) and relatively short neutron wavelength; therefore, the intensity of grouped reflections was considered. The Kennicott modification7 of the Busing-Martin-Levy program6 was employed to determine the identity of the atoms at the various lattice sites and the positional parameters. RESULTS A structure for the prototype compound Fe2P was first reported by Hendricks and Kosting;8 however, the structure was in error. The correct structure, as reported by Rundqvist and Jellinek,9 is as follows. The unit-cell constants and volumes per formula weight (V/M) are given in Table I for the sixty compounds examined in this investigation and classified as Fe2P-type compounds. The structure type was determined initially from a comparison of the unit-cell constants of HoNiAl with other known examples of this structure type1' and from the density of HoNiAl, given in Table 11. The density indicated that three formula weights comprised a unit cell, as in the prototype compound Fe2P. The assignment of the three species to lattice sites was made initially on the basis of atomic size. The large holmium atoms were assigned to the 3(g) sites that have a relatively large interatomic distance to nearest neighbor positions, the small nickel

Jan 1, 1969

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By A. Hultgren, G. Phragmén

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

By G. Phragmén, A. Hultgren

Page Outline of Progress of Knowledge and Theories about Gas Evolution in Steel Ingots. and Its Influence on Crystallization and Segregation................ 134 Object of Present Investigation........................................... 148 Theoretical Discussion of Process of Solidification........................... 149 Gas Given Off from Rimming Steel during Solidification................... 149 Equilibrium Diagram of the Iron-carbon-oxygen Alloys................... 151 Solidification of Pure Iron-carbon-oxygen Alloys.......................... 157 Solidification when Carbon Monoxide Is Given Off at Constant Pressure... 157 Solidification when Gas Evolution Is Suppressed....................... 158 Schematic Application on Solidification of Rimming-steel Ingots.......... 159 Influence of Manganese, Sulphur and Phosphorus......................... 160 Experimental work..................................................... 162 Liquid Steel and the Mold Gas......................................... 162 Ingots Investigated and Methods Used.................................. 165 Ingot structure....................................................... 174 Structure of Rim Zone.............................................. 174 Structure of Core................................................... 181 Structures Obtained under Special Conditions of Freezing................ 182 Distribution of Metalloids............................................. 187 Other Observations Made............................................. 192 General Discussion of Solidification Process................................. 195 Condition of Liquid Steel before Casting................................. 195 Rimming Period...................................................... 202 Composition of Rim Zone............................................. 225 Freezing after Top Is Closed........................................... 228 Slag Inclusions and Ingot Scum........................................ 234 Reaction between Gas in Blowholes and Surrounding Solid Steel during Cooling 235 Summary.............................................................. 237 Appendix—Preparation and Etching of Ingot Sections....................... 238 References............................................................. 239 In 1934, Jernkontoret (The Swedish Ironmasters' Association) appointed a committee for the study of the structure of rimming-steel ingots and the various phenomena associated with their solidification. The members of the committee, including those who have joined it later, have been: I. Bohm, B. D. Enlund, B. Kalling, M. Tigerschiöld, S. Wohlfahrt and the authors. The present paper‡ is a somewhat

Jan 1, 1939

Jan 1, 1962