Search Documents

By C. K. Eilerts

Finite difference equations were programmed and used to integrate the second-order, second-degree, partial differential equation with variable coefficients that represents the transient linear flow of gas-condensate fluids. Effect was given to the change with pressure of the compressibility factor, the viscosity, and the effective permeability and to change of the absolute permeability with distance. Integrations used as illustrations include recovery of fluid from a reservoir at a constant production rate followed by recovery at a declining rate calculated to maintain a constant pressure at the producing boundary. The time required to attain such a limiting pressure and the fraction of the reserve recovered in that time vary markedly with properties of the fluid represented by the coefficients. Fluid also is returned to the reservoir at a constant rate, until initial formation pressure is attained at the input boundary, and then at a calculated rate that will maintain but not exceed the limiting pressure. The computing programs were used to calculate the results that would be obtained in a series of back-pressure tests made at selected intervals of reservoir depletion. If effect is given to the variations in properties of the fluid that actually occur, then a series of back- pressure curves — one for each stage of reserve depletion — is required to indicate open-flow capacity and related flow characteristics dependably. The isochronal performnce method for determining flow characteristics of a well was simulated by computation. INTRODUCTION The back-pressure test procedurel is based on a derivation of the equation for steady-state radial flow of a gas, the properties of which are of necessity assumed to remain unchanged in applying the test results. The properties of most natural gases being recovered from reservoirs change as the reserve is depleted and pressures decline, and the results of an early back-pressure test may not be dependable for estimating the future delivery capacity of a well. The compressibility factor of a fluid under an initial pressure of 10,000 psia can change 45 per cent and the viscosity can change 70 per cent during the productive life of the reservoir. There are indications that the effective permeability to the flowing fluid can become 50 per cent of the original absolute permeability before enough liquid collects in the structure about a well as pressure declines to permit flow of liquid into the well. The advent of programmed electronic computing made practicable the integration of nonlinear, second-order, partial differentia1 equations2.3 pertaining to flow in reservoirs. Aronofsky and Porter4 represented the compressibility factor and the viscosity by a linear relationship, and integrated the equation for radial flow of gas for pressures up to 1,200 psi. Bruce, Peaceman, Rachford and Rice5 integrated the partial differential equations for both linear and radial unsteady-state flow of ideal gas in porous media. Their published results were a substantial guide in this study of integration of the partial differential equation of linear flow with coefficients of the equation variable. The computing program was developed to treat effective permeability as being both distance-dependent and pressure-dependent. In this study all examples of effective permeability are assumptions designed primarily to aid in developing programs for giving effect to this and other variable coefficients. The accumulation of data for expressing the pressure dependency of the effective permeability is the objective of a concurrent investigation. FUNDAMENTAL DIFFERENTIAL EQUATIONS DIFFERENTIAL EQUATION OF FLOW Linear transient fluid flow is represented by the partial differential equation,

Jan 1, 1965

By Rex W. Woods

The clue history of performance of a highly volatile type oil reservoir which is now greater than 80 per cent depleted is presented. The reservoir is at a depth of approximately 8,200 ft and includes an area greater than 7,500 acres. The reservoir has been exploited by 10 wells which to date have yielded about 10,880,000 bbl of stock tank oil by pressure depletion. Reservoir pressure has declined from an original of 5,000 psi to approximately 1,450 psi. Produced gas/oil ratio has increased from 3,200 to 23,000 cu ft/bbl with a corresponriing increase in APl gravity of the stock tank oil from 440 to 620 . Pressure and fluid data are given for different stages of depletion. INTRODUCTION In papers by Sloan,' and Cook, Spencer and Bo-browski,' properties of highly volatile type reservoir oil were discussed in detail and methods were presented for predicting performance of reservoirs containing this type of fluid. The purpose of this paper is to present performance history of a highly volatile type oil reservoir designated as Reservoir A which has been produced by pressure depletion and field separation without processing of gas GEOLOGY The reterence field which includes Reservoir A is a structural feature north of a trend of major folding along a northeast-southwest axis. In the area of development, the structure has the appearance of a dome with formation dip of three to four degrees, but structural relations between the reference field and the axis of major folding to the south have not been determined. No faulting within the field is evident. Oil and gas productive sands have been found at depths of 7,000 ft to 10,000 ft in a columnar section of Mio-Oligocene age. The sand bodies in the section are lenticular and usually continuity of sand is limited to a small area. Sand A which forms Reservoir A at a depth of 8,200 ft, however, has exceptional continuous development in the reference field. Fig. 1 shows an isopachous map of net oil sand for Reservoir A. Net thickness of oil sand at producing wells ranges from 14 to 34 ft with an average of 22 ft. Pinch-out of sand has been shown by drilling in the southwest part of the field, but extent of the reservoir on the northwest and northeast parts of the field is indicated only by thinning of the sand. The vertical oil column between the highest and lowest producing well in the reservoir is 339 ft. No water-oil contact has been found within the reservoir. As interpreted from the isopachous map, the reservoir includes about 8,900 acres with an average net sand thickness of 12 ft. Because of limited data on extent of the reservoir, the isopachous map permits only an approximation of sand volume in the reservoir. DEVELOPMENT AND PRODUCTION Reservoir A was discovered during 1938 and was developed with eight wells to the end of 1942. One well was completed during 1946 and the tenth well in the reservoir was completed during 1951. Three of the original wells and the last completion have produced from Sand A only. Six wells have produced from Sand A through the casing side of dual completions. Initial producing rates of the original wells ranged from 800 to 1,000 BOPD. Production history for the reservoir is shown in Fig. 2. Production of the reservoir was begun during 1940 and in May, 1952, peak production from seven wells was 5,300 BOPD. At the end of March, 1954. cumulative production was 10.880,000

Jan 1, 1956

By H. O. Hofman

The object of refining copper in the reverberatory furnace is to obtain a metal which will have the highest attainable degree of malleability, ductility and electric conductivity, and present at the same time a level surface when it solidifies in the mold after casting. These desirable physical properties are governed by the character of the impurities and the forms in which they are present, by the amount of cuprous oxide retained by the copper, by the quantity of gas held in solid solution, by the casting-temperature, and by the thickness of the casting. The effects of impurities, of cuprous oxide and of gases upon the mechanical properties of copper have been studied by Hampe1 in his classical paper " Colitributions to the Metallurgy of Copper." The most recent research into the effect of metals upon the electrical conductivity of copper is that of Addicks. 2 The influence of cuprous oxide upon the electrical conductivity has been investigated by Walker3 and Addick. 4 The absorption of gases has received attention by Hampe: Stah16 and Heyn 7 The effects of casting-temperature have been noted by Stahl.8

Jan 1, 1908

By J. T. Peters, N. Schapiro, R. J. Gray

Petrographic studies of coal have resulted in a better understanding of the origin and composition of coal and have added to the knowledge of how and why coals differ in their response to various prepamtion and utilization processes. Petrographic methods can now be used in scientific economic exploitation of coals. Because the United States Steel Corp. is one of the largest consumers of coal and coke, there is a continuing interest in the corporation in perfecting a better understanding of coal so that it can be utilized more effectively. Coal is a heterogeneous substance composed principally of plant material that has been altered by a complex geochemical process to form rock. The science of coal is anthracology. The ultimate aim of anthracology is determining the relationships and differences among coals. The fundamental aim is finding out why coals differ. The practical application is determining how the differences in coals affect their utilization properties. Coal, like other sedimentary rocks, consists of more than one material. Fig. 1, a photograph of a natural fracture and a polished surface of a lump of coal, displays heterogeneity in terms of the banded ingredients present. The earliest attempts to describe coal were based on its hardness and appearance. ' Thus, coal has been described as hard or soft, bright or dull, and banded or nonbanded. The variations in the hardness and physical appearance of the coal reflect differences in materials that constitute the coal. The banded nature, lustre, and texture depend upon the relative proportions of the various constituent materials. Even the earliest petrographic investigations of coal produced evidence of of the heterogeneity of the coal substance and shoul have destroyed the concept of the unit coal molecule. Coals (Fig. 2) that appear the same frequently consist of different microscopic materials and may behave differently during mining, pulverization, washing, or coking. In Fig. 3, the upper photograph shows a bright at-trital medium-volatile coal, and the micrograph at the right shows some of the materials that constitute the coal. The lower photograph shows a bright attrital low-volatile coal and the corresponding micrograph shows material of similar origin to those from the medium-volatile coal. Any petrographic description of a coal that has meaning in terms of its utilization begins with a microscopic examination. Numerous attempts have been made to describe coal on the basis of the materials that constitute the coal.2*3 Initial petrographic studies were directed towards the question of the origin of coals without any true basis for studying the metamorphic changes in the

Jan 1, 1962

By R. D. Boddorff, R. L. Ash, C. T. Butler, W. W. Kay

DRILLING and blasting in anthracite open-pit mines is a continuous problem to contractors and explosive engineers because of the diverse conditions caused by the nature of the geological formations, the extensive mining of the portions of coal beds near the surface, and the proximity of many strip pits to populated areas. Pennsylvania anthracite occurs in four separate long and narrow fields totaling only 480 sq miles. The coal measures are rock strata and coal beds that are considerably folded and faulted. The crests of the anticlines are eroded extensively. The beds outcrop on the mountain sides and dip under the valleys. At first only the upper portions of the synclines could be stripped. Now stripping to increasingly greater depths is economically possible, as is indicated by the fact that the proportion of freshly mined anthracite produced by strip mining has increased from 3.7 pct of the total tonnage in 1930 to 29.6 pct in 1950. Much of the rock overlying the deeper beds now being stripped is so extensively broken that considerable difficulty is experienced in drilling satisfactory blast holes and in using explosives in such manner as to insure a uniformly broken material easily removed by the excavating machinery. Such breaking of rock strata has occurred because the bed now being stripped has been mined extensively in former years by underground methods, and tops of gangways and chambers have subsequently failed. Draglines are used to uncover coal where the overburden can be moved with little or no rehandling. These machines range in size from those having a 2 cu yd capacity bucket on a 60-ft boom to those handling a 25 cu yd bucket on a 200-ft boom. Draglines are also used to strip to the bottom of the coal basins if the depth and the distance between the crops are not too great. For this type of operation blast holes are drilled full depth to the bed. These holes are commonly 30 to 90 ft deep; however, in exceptional cases, holes may be as shallow as 12 ft or as deep as 130 ft. Drilling is normally done for blasts of 12,000 to 60,000 cu yd of overburden, 30,000 cu yd being considered an average blast if vibration is not the controlling factor. Where the stripping of wide basins or the exposure of a moderately pitching vein makes the use of draglines impractical, dipper front shovels equipped with 4 to 6 1/2 cu yd buckets load into trucks. Overburden is removed in benches of 25 to 30 ft with blast holes drilled 4 or 5 ft deeper than the planned floor of the bench. For shovels under 5 cu yd bucket capacity the volume blasted varies from 8000 to 12,000 cu yd, whereas a volume of 30,000 to 50,000 cu yd of overburden is frequently blasted at one time for the larger shovels where vibration is not an important factor. During the past decade the churn drill, generally the Model 42-T Bucyrus-Erie blast hole drill equipped for drilling 9-in. diam holes, has become the most common blast hole drilling machine. Electricity powers half the churn drills in use and is preferred on the large strippings where electric shovels are operated and the working area is concentrated. On these operations the cost of additional electricity for the drills is less than the cost of fuel to operate diesel units because of the existing large demand load of the excavating equipment. Moreover, electric motors start more easily in cold weather and generally are less expensive to maintain. Diesel driven units are employed where a higher degree of mobility. is required. The average drilling speed is 8 ft per hr, although in softer rocks a rate of 15 ft per hr is attained. Where rock is hard and strata is badly broken, drill speeds may ' be less than 2 ft per hr. Low drilling production results under these circumstances when loose material falling from the upper portion of the drill holes causes drill stems to be jammed. Rock formations vary so greatly in the region that a 9-in. diam churn drill bit may become dull after drilling only 2 ft or may drill satisfactorily for 56 ft; however, an average of 35 ft is usual in sandstone of medium hardness. Dull bits are hoisted to flat bed trucks by the sand line of the drill and are usually sharpened in the contractor's bit shop adjacent to the job. Care is generally taken to cover the thread end of the bit with a cap. To facilitate handling of bits around the drill, a heavy thread protector having an eye top is becoming more popular than the flat-top rubber or metal cap furnished with new bits. The 9-in. diam blast holes for a 25 to 30 ft bench are normally on 18x18 ft to 20x20 ft spacings, depending on the character of the overburden, although in broken ground 15x18 ft centers may be used to obtain better breakage and a more even bottom for the bench. The patterns of holes for shots

Jan 1, 1952

By T. N. McVay, E. E. Creitz

Rather large amounts of titanium minerals and some zircon and monazite are being recovered from dune sands about I. miles west of Jacksonville Beach, Fla. The Mining Branch of the Bureau of Mines, Southern Experiment station, has been interested in developing additional large deposits of similar sands in other areas of Florida. The results of a field study have been published1 concerning the sands occurring on Trail Ridge which runs north and south about 30 miles southwest of Jacksonville. This investigation was undertaken in order to identify the opaque titanium minerals occurring in Trail Ridge and because of the economic importance of Florida titanium minerals. Nature of the Problem The minerals present in the heavy fractions (sp gr > 2.94) of the sands are principally opaque minerals; staurolite, zircon, sillimanite, tourmaline, kyanite, rutile, a small amount of corundum, traces of the zinc spinel gahnite and garnet. Epidote, monazite, hornblende and ti-tanite are present in other dune sands but these minerals were not noted in the samples collected on Trail Ridge. All of the minerals except those which are opaque can be readily identified by the usual petrographic methods. However, Opaque minerals cannot be examined satisfactorily by transmitted light. Polished sections of the opaque-mineral grains were examined but these sections did not furnish useful information. Consequently, it was necessary to use means other than the usual petrographic methods to identify them. Previous Investigations of Heavy Minerals in Florida Sands Martens2 has described the heavy minerals in the Florida beach sands and has classified the opaque minerals as ilmenite with minor amounts of leucoxene. Miller3 studied a number of sands collected by Ross and Mertie in Florida. He states that the material from the Florida beach and dune sands that commonly has been called ilmenite has essentially the chemical composition of the material that has been called arizonite.4 The x ray diffraction patterns of several samples indicated that the supposed ilmenite is essentially amorphous, with only weak lines corresponding to ilmenite, and hence the material is unlike the type of arizonite from Arizona. Opaque Titanium Minerals Rutile is essentially titanium dioxide. However, as pointed out by Dana,5 important amounts of Fe+2 and Fe+3 as well as Cb and Ta are reported in some analyses.

Jan 1, 1949

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s7 the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981

By C. Zener, H. Nielsen, D. Van Winkle

THE internal friction of metals has been studied frequently at elevated temperatures.1-4 In most cases it rises rapidly with increasing temperature. The notable exceptions are ferromagnetic materials, and lead.2 This paper describes an investigation of the general features of the high-temperature internal friction of 70-30 alpha brass. EXPERIMENTAL METHOD The internal friction of a metal is a measure of the rate at which it dissipates energy of vibration. The measure adopted here, I/Q, is (I/2p) times the specific damping capacity, a measure commonly used by engineers. In the measurements of this investigation, the stress level was kept so low that the observations were independent of the stress. The general method of making such measurements, and of observing the temperature of the specimen during a measurement, has been described elsewhere.5,6 The driver and detector coils were wound with wire insulated with glass thread, in order to withstand the high temperatures used. In previous work electrical eddy currents in the specimen served as the coupling between the mechanical vibration of the specimen and the electrical circuits of the driver and detector. The high values of the internal friction in the present investigation rendered this coupling insufficient. In order to increase this coupling, pole pieces cut from ordinary telephone diaphragms were attached to the specimen. A mixture of French chalk and water glass proved a satisfactory cement. All measurements were made at the fundamental frequency for transverse vibration, which lay between 600 and 900 cycles per second. SPECIMENS The measurements described herein were made upon a single cylindrical rod of brass, kindly furnished by Dr. Cyril Stanley Smith, of the American Brass Co. This rod was the specimen E of the set of alphabrass rods described in an earlier paper.6 Successively larger grain sizes were obtained by annealing at successively higher temperatures. A slice was cut off one end after each set of measurements. Grain counts were made on each slice by W. E. Lindlief, of the American Brass Co. Nine fields were viewed on each piece, located as shown in Fig. I. Results are given in Table I. The grain size is defined in the usual way; namely, Grain size = I/n ½ where n is the mean number of grains per square millimeter. EXPERIMENTAL RESULTS This paper is concerned exclusively with the part of the internal friction that becomes dominant at high temperatures. It is thus desirable to separate this part of the internal friction from the part that is

Jan 1, 1942

By Bruce A. Kennedy

The 1960's were an apparent turning point in the technological and social attitudes and awareness of the mining industry. From the late 19th century through to the early 20th century, one has always been presented with the picture of the rough and ready leaders of the mining industry who screamed for production and damned anything that got in the way of it. This attitude led to a certain alienation of the mining industry in the eyes of the general public. They saw an industry which was archaic in many of its practices and often heartless in its attitudes towards mankind. However, a gradual change spread through the industry and cracks began to appear in the hard facades of the mining companies. Resistance to change had almost become a standard operating procedure for many and consequently changes in technology had been slow in coming. The late 1950's and the 1960's saw a new awareness come into existence. As the mining company managements changed, there developed a realization that considerable efforts had to be made to bring the technology and social standing of the industry out of the dark ages and into the modern world. New advances were made in both metallurgical and mining technology. The 20th century technology of computers was accepted and became a standard tool of the industry.

Jan 1, 1971

By C. D. Stahl, S. M. Farouq Ali, W. E. Culham

One- and two-dimensional mathematical models have been developed that simulate transient, two-phase flow of hydrocarbon mixtures in porous media in a manner that accounts for interphase mass transfer. Numerical simulations of one-dimensional depletion-drive experiments using a two-component hydrucarbon fluid were used to establish the validity of the mathematical models. In addition, the experimental and numerical data were used to demonstrate that production rate had a relatively insignificant effect on the recovery of individual hydrocarbon components from the experimental system, and that attainment of equilibrium between phases is possible for a wide range of liquid and vapor velocities in reservoirs containing light hydrocarbon fluids. Results of some two-dimensional numerical simulations are also presented. INTRODUCTION This study was undertaken to develop a mathematical model that would simulate transient, two-phase flow of hydrocarbon mixtures in porous media under conditions that result in interphase mass transfer and to test the validity of the assumptions used to set up the model. In addition, the study was designed to determine if production rate influences the recovery of individual hydrocarbon components from reservoirs producing by depletion drive. Two-phase flow in porous media, with interchange of components between the two phases, is important in many petroleum recovery processes. Studiesl-5 conducted within the last 3 years have outlined methods of solving multiphase flow problems incorporating mass transfer. Some of these studies have also indicated the importance of accounting for mass transfer under various producing conditions. An earlier work6 first demonstrated the importance of combining relative permeability data with equilibrium ratios in compositional balance methods. The mathematical model presented in this paper is formulated so that a phase behavior package, as described in previous papers,5,17 is not required as an integral part of the routine employed to solve for the primary dependent variables. The finite difference formulation is designed so that all the primary variables can be solved for simultaneously. This is accomplished by utilizing one basic set of equations. These innovations, which are in contrast to other models2,3,5 but are similar in some respects to the approach used by Taylor,l render the total problem computationally simpler than any of the previously referenced formulations. The mathematical model was developed by combining Darcy's law with a continuity equation for each hydrocarbon component. The principal assumptions invoked in the formulation were (1) that capillary forces and diffusional effects are negligible, and (2) that thermodynamic equilibrium exists in the reservoir at all times. No assumption as to the type of vaporization process was made in formulating this model. Experimental data were required to complete this study. These were generated by conducting several depletion drive experiments. The experimental apparatus consisted of a sandstone core enclosed in a pressurized casing. The apparatus was designed in such a manner that the core could be charged with a liquid hydrocarbon mixture and depleted at different production rates. The experimental tests were designed to determine the effect of production rate on component recovery. In addition, direct comparison of experimental and mathematically predicted

Jan 1, 1970

By T. A. Read, M. W. Burkart

The crystal geometry of the cubic-tetragonal interface after partial transformation of an indium-thallium alloy single crystal is described and a general theory is presented. The effects of applied stresses on this transformation are interpreted and the latent heat of transformation is obtained from observations of transformation under stress. A DIFFUSIONLESS phase transformation between face-centered cubic and face-centered tetragonal structures has been reported for the indium-thallium system by Bowles, Barrett, and Guttman1, 2 The transformation takes place at approximately 105 "C at 18 atomic pct Tl and 25°C at 23 pct Tl. In their study, Bowles, Barrett, and Guttman used poly-crystalline samples whereas in the present study single crystals were used to eliminate the transformation constraints imposed by adjoining grains. The use of single crystals made possible a comprehensive study of the effect of stress on the transformation. In the course of the work, it was possible to formulate a new method of analyzing dif-fusionless transformations (presented in this paper) which permits calculation of the geometry of the interphase interface from a knowledge of the crystal structures of the initial and final phases. The specimens were prepared from chemically pure thallium and 99.97 pct In which were weighed out to produce 3 to 4 grams of alloy of the desired concentration. The metal was placed in clean fused silica tubing, then melted, degassed and sealed under vacuum. (To obtain single crystals, it was found that both degassing and extreme cleanliness were essential.) Single-crystal specimens were grown by a modified Bridgman technique.8 pecimens were removed from the tube by dissolving the quartz in concentrated hydrofluoric acid which attacks the specimen very slowly. The specimen then was polished mechanically to produce four flat surfaces, electropolished, and annealed at 140°C for 48 hr. The electropolishing solution used was that described by Bowles, Barrett, and Guttman and the polishing was carried out on both the high and low temperature phases of the alloy. The high temperature polishing was done at 110°C with a stainless steel cathode. Visual Observation of the Transformation in Single Crystals A visual study of the transformation was made on specimens which had been electropolished in the high temperature phase. The specimens were supported on the stage of a metallograph by an electrically heated holder which contained an opening for observing the specimen. Visual evidence of transformation was found in the presence of an interface which separated the two phases. The interface plane defines the boundary of the phase undergoing transformation and manifests itself by the sharp change in angle between the surface of the specimen and the incident light at the juncture of the two phases. On slow cooling, well-annealed specimens transformed from the face-centered cubic structure to the face-centered tetragonal structure by the motion of a single plane interface which traversed the specimen from one end to the other. Upon heating, the interface moved back in the reverse direction. The interface could be started, stopped, or reversed at will. A temperature hysteresis of about 31/2oC was observed in the reversal of the interface. Holding an interface stationary caused it to disappear completely in most cases, whereas in other instances the interface became less distinct depending upon its orientation. The interface could be made to reappear by changing the temperature of the specimen. The low temperature tetragonal structure exhibits only the fine markings or subbands reported by Bowles, Barrett, and Guttman and is illustrated in Fig. 1. These subbands are twin-related. Back-reflection Laue patterns show the breakup of the cubic spots into pairs of spots corresponding to the twin orientations of the tetragonal phase.

Jan 1, 1954

By C. H. Mathewson

IN a series of papers published recently,1 R. F. Mehl and associates have studied the characteristics of form and orientation of many segregate structures and have found diversified conditions which can be explained only by postulating some specific kind of cooperative mechanism permitting the matrix lattice in some favorable region to transform into the segregate lattice in an adaptable region presenting a geometrically similar arrangement of atoms. We have collected the published data on crystallographic relationships of this sort, chiefly derived from Mehl's work, in Table 1. It is evident at once that the crystal structure of the matrix does not uniquely determine the location of the plate structures or other forms assumed by the segregate. Thus, the first seven items in the table represent precipitation of platelike forms from a matrix of face-centered cubic structure, but these plates are found stratified along planes of form {111 }, {100 }, {110 } or another unidentified form, depending upon specific conditions involving the nature and concentration of the segregating substance. Again, in a matrix of body-centered cubic structure, plates, needles or stars have been found and the favored inner surface of segregation may be a plane of form 11101, 11121, 12101, or indeed a surface without crystallographic indices defining a bundle of close-packed lattice lines (strings of atoms) taken more or less at random. Such a surface might be formed ideally by revolving one of these parallel strings of atoms around another as an axis. Hanemann and Schroder2 recently discussed these questions, principally with relation to original conceptions concerning the process of

Jan 1, 1932

By Sir John Cadman

Since my previous review of the Persian fields, presented in 1929,' considerable progress has been made. The main feature of drilling development has been the delimitation of the Haft Kel field and its extensions. Although the limits have not yet been reached, a productive area of about 40 square miles has already been proved and it is now certain that the field will be of the same order of importance as the Masjid-i-Sulaiman field. Production to main pipe line from Haft Kel was begun in November, 1929, and to date about 4,500,000 tons have been produced. Normal production has continued from the Masjid-i-Sulaiman and Naft Khaneh fields. The search for oil in horizons below the main producing limestone is perhaps the most interesting and important exploratory drilling work in progress. Promising results have been obtained in the first well deepened in the Masjid-i-Sulaiman field with this objective, and the exploration of these lower formations is being continued. In this connection an allied program of geochemical research work on the nature of the oils and oil-bearing rocks of different horizons is at, present being undertaken. Masjid-i-Sulaiman Field Since the Haft Kel field was brought into production in 1929, production from Masjid-i-Sulaiman has been reduced in order to equalize to some extent the producing lives of the two fields. The production for the last four years has been as follows: m Approximate Equivalent in TonB Barrels 1929 5,434,071 38,038,497 1930 4,925,869 34,481,083 1931 4,248,086 29,736,602 1932 Approximately 4,500,000 31,500,000

Jan 1, 1933

By Richard Birk

Rf sputtered quartz has been successfully used in multilayer interconnects for MOS devices. The target potential was 2000 v peak to peak with a frequency of 13.56 Mc per sec. The sputtering rate was approximately 60A per min with an operating pressure of argon gas at 10 to 15 p. The dielectric strength is 8.0 x 10' v per cm and the pinhole density is less than 2 x 10-2 per sq mm. Infrared absorption peaks for the Si-O vibrational bands we at 9.4, 12.4, and at 22.5 p. The etch rate of the sputtered SiO2 is 1200A per min. MOS devices have been fabricated using multilayer interconnects with no degradation of electrical characteristics. MULTILAYER interconnects require an insdating film between the metal layers which can be deposited below any potential eutectic temperature. Sputtered Si4, which can be deposited with substrate temperatures below 200°C, satisfactorily meets the multilayer insulation requirements and has been used to prepare MOS circuits with multilayer interconnects. The physical and electrical properties of rf sput-

Jan 1, 1969

By Herbert J. French

Herbert 1. French (Member 1934), vice president of the International Nickel Co. Inc., assistant vice president of the International Nickel Co. of Canada Ltd., and AIME Howe Memorial Lecturer for 1956, died in Rochester, Minn. on Aug. 17, 1955, after a long illness. Before his death, Mr. French had laid the foundation of research on which the Howe Memorial Lecture (p. 770) was based. His associates at Inco, 0. 0. Miller and J. W. Sands, were able to complete the project, present the lecture, and prepare it for publication, following Mr. French's general outline. Born in New York on May 27, 1893, he graduated from the School of Mines, Columbia University, with a degree in metallurgical engineering in 1915. Mr. French gained his early engineering experience with the American Smelting and Refining Co., serving as a chemist and as-sayer at the company's Murray, Utah, installations. He later returned east and became a metallurgical engineer for the General Vehicle Co., Long Island City, IT. Y., a subsidiary of the General Electric Co. In 1917 Mr. French was appointed civilian inspector of materials for the U.S. Army Signal Corps, and continued this work when it was later absorbed into the Bureau of Aircraft Production. Subsequently he was appointed district inspector in Philadelphia for the Pittsburgh (Ordnance Metallurgical) office, later transferring to Pittsburgh. After World War I Mr. French became an assistant physicist on the metallurgical staff, U. S. Bureau of Standards, Washington, D. C. During his years with the Bureau, he was successively associate physicist, metallurgist, senior metallurgist, and assistant chief, division of metallurgy. In 1929 Mr. French joined International Nickel as a metallurgist at the company's Bay-onne, N. J., research laboratory. Transferring to the development and research division, New York, in 1931, he took charge of alloy steel and iron development, becoming assistant manager of this division in 1943. Mr. French's appointment as an Inco vice president came in March 1947. Previously, he was appointed assistant vice president of the International Nickel Co. of Canada Ltd. in January 1947. Mr. French served the War Production Board during World War II as senior technical consultant in charge of the metallurgical and specifications section of the iron and steel branch. When this section of the WPB was organized into the steel division, he was appointed chief of the metallurgical branch. From March 1944 to September 1945 Mr. French served as assistant director. Herbert French was well known not only for his prolific contribution to the metallurgical literature, for which he received numerous awards, but also for his prolonged service to the profession through its technical societies. He was a past president of ASM, and was the Campbell Memorial Lecturer for that group in 1933. Mr. French was honored by the American Society for Steel Treating in 1931 when he was awarded the Henry Marion Howe Medal. A series of lectures he gave in 1941 before the Fourth Western Metal Congress in Los Angeles was later published in book form under the title Alloy Constructional Steels.

Jan 1, 1957

By John Jan

Iodine is a soft, lustrous, grayish-black non- metallic element with a density of 4.9. It is the least active of the four members of the halogen family. The other members are, in order of increasing activity, bromine, chlorine, and fluorine. Iodine is a solid at ordinary temperatures, while bromine is a liquid and chlorine and fluorine are gases. Iodine melts at 113°C and volatilizes at 184.4°C to a blue- violet gas with an irritating odor. It occurs in nature only as iodates and iodides or other combined forms. It was discovered by Bernard Courtois in France in 1811, who noticed its presence as an unknown substance in crude soda ash obtained from burning seaweed. Gay-Lussac recognized it as a new element and named it iode, from the Greek word "ioeides or iodes" for violet color (MacMillan, 1970). The world production is not known with any great certainty, but it is probably between 20 and 25 million lb per year, of which about 25% is consumed in the United States. Geology and Mineralogy Iodine compounds occur as a minor constituent as a mineral in the Chilean nitrate deposits and in solution in brines and sea- water. According to the U.S. Geological Survey, it is the 47th most abundant element in the earth's crust. The minerals lautarite, Ca (10,) (calcium iodate), and dietzeite, Ca, (10,) , (CrO,) , (calcium iodate-chromate) are found in Chilean nitrate deposits which are located in Antofagasta and Tarapach provinces on the eastern slope of the coast range in a desert area. Various brines contain iodine compounds. Seawater contains about 0.05 ppm of iodine and some seaweeds will extract and accumulate it up to 0.45% on a dry basis. Some coals in West Germany also contain iodine compounds. The known and potential sources of iodine reported in 1968 are given in [Table 1]. Iodine has been recovered from brines in Java, Indonesia, France, England, and the USSR. Iodine has also been recovered from seaweed in Ireland, Scotland, France, Japan, Norway, and the USSR. The indicated re- serves and future resources of iodine are large but have never been adequately measured. Analysis Iodine as the free element can be detected by the characteristic blue color it gives to a starch solution. Quantitatively it is determined as the free element by titration with standard thiosulfate solutions using starch as an indicator. Colorimetric methods are also applicable.

Jan 1, 1975

By B. Chalmers

THE practical importance of the phenomena of melting and freezing must have been recognized for a very long time. The difference between ice and water, for example, has had a profound influence on the history of mankind and the evolution of society. The possibility of melting a metal and allowing it to freeze in a mold of chosen shape has been an essential ingredient in our mastery of the art of shaping metals, and therefore in the evolution of the: machine age in which we find ourselves. The importance of melting and freezing, as applied to metals and alloys, has been so great, in fact, that empirical solutions have been found for the multitude of practical problems that have arisen. This approach has been so successful that relatively little attention has been directed to arriving at an understanding of the fundamentals of the processes. But metallurgy has come to a stage at which we may expect that some, at least, of the more complex problems that have not yet been solved (or perhaps even recognized) may be handled more effectively by scientific study, theoretical understanding, and logical experimentation than by trial and error. In this lecture, therefore, I propose to describe in outline what I think really happens when a metal freezes. In doing so I hope to explain many of the phenomena which have been observed, and in particular to account for the structures that are obtained in actual ingots and castings. The basic problem, to which this lecture represents a tentative partial answer, is this: a mass of metal, containing known proportions of various elements, is melted, heated to a given temperature, and then allowed to freeze under specified conditions. What will be the "structure" of the resulting metal? The term structure includes: 1—crystal size, shape, and orientations, 2—distribution of chemical elements, and 3-—shape, including cracks, cavities, pores, etc. The Solid-Liquid Interface We will first consider what takes place if a single crystal of a metal in the form of a rod is heated, not uniformly, but so that one end is hotter than the other. If this heating process is continued long enough, the hotter end will eventually melt; we will suppose that the rod is in a containing vessel so that the molten metal does not run away, Fig. 1. When some of the metal has melted, we have some solid, some liquid, and an interface or surface of contact between them. If the source of heat is now removed, the interface will move so that some of the liquid freezes, and if the supply of heat is suitably adjusted the interface will remain at rest. This very simple arrangement allows us to study the basic processes of melting and freezing, and if we fully understand this simple case, we may be able to account for what takes place under practical conditions where the heat does not all flow in the same direction, and where the heat flow is determined not by a controllable source of heat but by the heat capacity and temperature of metal and mold, and by the heat loss from the mold surface. The solid-liquid interface is evidently the region of the greatest interest to us; on one side of it there is crystalline solid, and on the other, liquid. In the solid, each atom has a well defined position, around which it vibrates as a result of thermal agitation. It only leaves this position in the relatively rare event of a "diffusion jump." The liquid is much less systematically organized. The atoms are about as far from their neighbors as in the solid, but the arrangement is much less systematic and is continuously changing. The solid and the liquid are represented diagrammatically in Fig. 2. The average energy of the atoms in the liquid is greater than in the solid by an amount that corresponds to the latent heat of fusion, i.e., the amount of heat that has to be supplied to convert unit mass of solid into liquid at the same temperature. The Two Processes As has recently been shown by Jackson and Chalmers,3 many of the features of the processes of freezing and melting can be understood if it is assumed that a continuous and rapid interchange of atoms between solid and liquid always takes place at a solid-liquid interface." It is necessary to con- sider two distinct processes, that of melting, in which atoms leave the surface of the solid and become part of the liquid, and the converse process,

Jan 1, 1955

By G. F. Loughlin

Nearly 55 years have elapsed since the U. S. Geological Survey was organized. During this period the mineral industries have grown from infancy or early childhood to well developed maturity, and some mining industries appear to be declining. Decline in mining is even more conspicuous in certain districts, or even states, than in any mining industry as a whole, and discoveries or developments of important new districts have been very few in recent years. Our reserves of most metals and nonmetals are adequate for many years of normal production, subject to changes in rate of exploitation that may be caused by foreign competition and by changes in technology and market conditions; but the declining production of many districts and the scarcity of important new discoveries to compensate for them is cause for some apprehension. It is likely that future production will depend to a considerable extent on deep exploration and on the thorough examination of places in and adjoining existing districts where significant outcrops are lacking and only apparently insignificant geologic features offer encouraging clues—more so than on the discovery of entirely new districts. Even the possible discovery of new districts, which have escaped the intensive search by the nontechnical prospector, must be dependent on geologic information. There is therefore no need for argument as to the value of geology to the mining industry; and the need of continuing to advance the science. The U. S. Geological Survey's past contributions to mining geology, as expressed in its official reports and other publications, are recognized by Ransome in his historical review of mining geology in the Lindgren volume.' These contributions have helped to form the basis of modern mining geology, which has grown rapidly in the last 25 years. This growth has witnessed the organization and maintenance of geologic staffs by mining companies in several districts, and their detailed work, together with the fact that nearly all of the larger mining districts have

Jan 1, 1935

By F. W. Jessen, C. A. Johnson

The effect of treatment with ferrochrome lignosul-fonate on both sodium and calcium bentonites has been examined. In the early stages of treatment it appears that some base exchange of iron and chromium for sodium may occur with the sodium bentonite. Such exchange appears specific for exchange of sodium ions when the calcium ion concentration represents 40-5.5 per cent of the total exchangeable cations, and when additions of lignosulfonate are less than 1 lb per bbl. Adsorption appears entirely physical above 1 lb per bbl treatment level for all concentrations of calcium studied. Gel strength and plastic viscosity of both calcium and sodium bentonite systems were reduced with treatments of ferrochrome lignosulfonate up to 2 Ib per bbl, the greatest reduction occurring within a range of calcium concentration of 40-5.5 per cent of the total exchange capacity of the clay. INTRODUCTION The problem of control of viscosity and gel strength of drilling fluids by the action of thinners or dispersants has been studied by many investigators.1-7 In addition, much work has been done on formation of gel structure in clay suspensions. However, gel formation and structure still are incompletely understood, and the use of the various dispersing chemicals is based, to a large extent, on data almost entirely empirical in nature. In recent years the lignosulfonates have become increasingly important in the treatment and control of drilling fluids. More specifically, ferrochrome lignosulfonate has found rather wide acceptance, particularly in calcium systems.5-7 Lignosulfonates are refined lignin products made from spent sulfite liquor from which the fermentable sugars have been removed.15 The exact structure of lignin is not known; however, it is believed to be a phenolic propane type polymer which may exist as a branched chain or cross linked structure. The molecular weights of lignosulfonates probably range from 300 to 100,000 or more.15 A better understanding of the mechanism of adsorption of dispersants is essential before improvement and development of characteristics of drilling fluids and drilling fluid control is possible. This investigation was undertaken to determine the action of ferrochrome lignosulfonate on sodium and calcium montmOrillonite' LABORATORY INVESTIGATION A Stormer viscosimeter and Fann V-G meter were used to measure viscosity and gel strength. A Zeiss spectrophotometer was used for analysis of Fe and Cr and the flame attachment was employed in the analysis of Na, Ca and Mg. A General Electric X-ray diffraction unit utilizing Copper Ka radiation and a Ni-filter was utilized in the X-ray studies. PROCEDURE Two systems were studied. Predominately sodium clay, obtained from Wyoming, and a predominately calcium clay from Texas were used. These particular samples were chosen because of the extensive work of characterization completed by Mungan. Ionic base exchange capacity determined by flame photometry and total exchange capacity by the Kjehldahl method were obtained experimentally. A 7-per cent suspension of the sodium clay and a 20-per cent suspension of the calcium clay in distilled water were prepared by mixing with a high-speed mixer. The suspensions were allowed to stand for two weeks for complete hydration. Calcium chloride was added to portions of the sodium and calcium cla suspensions to obtain suspensions varying in Ca++ concentration as shown in Table I. A series of treatments was run with 500-ml portions of the original suspensions using a ferrochrome lignosulfonate. Treatment was carried out in the same way with each of the suspensions of varying Ca concentration. Viscosity and gel strength were measured and a filtrate obtained at each treatment level. Ten ml of filtrate were diluted to 50 ml, and aliquot portions of the 50 ml were taken for the Na, Ca, and Mg analysis by the flame photometer. The pH of these filtrates ranged from 7 to 7.3. Standard

By W. H. Bassett, C. Davis

Although brasses and bronzes have been made for ages, a systematic study of their physical properties has been carried out only during the years of the present century. Among these properties may be included those which are to be detected by means of microscopic examination; in other words by the science of metallography. The earlier workers in this field, both in this country and abroad, gave their attention to steel. When the senior author explored the situation in 1902, there was little encouragement to be found in undertaking the study of the non-ferrous alloys. A start was made, and the metallography of the brasses and bronzes, as well as of the copper-nickel-zinc alloys developed materially under his direction. Annealing experiments were begun in 1902, and in the succeeding years the effect of temperature, and the influence of previous working, on the grain size of brass were studied. The conclusions so well known and widely published today were largely reached during those earlier years. In 1905 the first complete annealing series were made. By this it is meant that brass and copper sheet, 5 B & S Nos. hard, was machined into tensile test specimens, then annealed under accurate control for 30 min. at temperatures up to the melting point of the material. Various determinations were made, including tensile strength and elongation in 2 in. There rapidly followed similar series on all of the copper-zinc alloys from 100 to 60 per cent, copper, on the bronzes, cupronickels, and on copper-zinc-nickel alloys. At this point there was published by Grard, in October, 1909,' the very comprehensive and complete work on the tensile properties of cartridge brass, 90-10 copper-zinc, and electrolytic copper. The excellent photomicrographs in that paper illustrated the changes in structure produced by cold rolling as well as by annealing at different temperatures, but where Grard's work was confined to copper and to two alloys, the investigations in this laboratory have been over the entire fields of the commercial copper-zinc alloys, copper-tin alloys, representative copper-nickel and copper-nickel-zinc alloys as well as aluminum bronzes and others of a more special nature.