Search Documents

By John D. Verhoeven

A technique has been developed for carrying out normal freezing experiments with a current density of 2000 amp per sq cut passing through the solid-liquid interface. The equation relating the effective distribution coefficient to the equilibrium distribution coefficient in electric field-aided solidification, originally developed by Huckc et al.,1 has been modified for the case of concentrated solutions. Preliminary experiments on the Sn-Bi system give qualitative agreement with the equation. The data are analyzed by a slightly novel use of the normal freeze equation which allows one to determine the effective distribution coefficient more easily. Very extensive mixing in the liquid was found at these high current densities and it is postulated that the mixing results from a vertical component of the magnetic Lorentz force generated by the electric current. In the search for techniques of obtaining ultrahigh-purity metals the inefficient but very effective technique of electrotransport has received little attention. Electrotransport is most effective in the liquid state and a natural application, therefore, is to apply an electric field across the liquid zone of a zone-melting experiment. The present investigation was undertaken to study the effect of an electric field upon solidification of metals, so that the usefulness of electrotransport in such solidification experiments as zone melting could be determined. In zone-melting and normal-freezing experiments it is difficult to achieve complete mixing in the liquid in the immediate vicinity of the solidifying interface. Consequently a solute build-up will occur at the interface in the portion of the liquid where complete mixing does not occur (an equilibrium distribution coefficient, ko, less than one, and unidirectional atom motion will be implied throughout). This local solute build-up produces a corresponding rise in the solute concentration in the solid so that the ratio of the solute concentration between the solid and the bulk liquid is larger than the equilibrium distribution coefficient. This ratio is defined as the effective distribution coefficient, k,. The differential equation describing the solidification process may be derived by applying the continuity equation to an expression for the net solute flux at the interface. The solution to this differential equation then allows one to determine the solute distribution in the liquid and the relationship between k0 and ke. One of the most useful solutions to this equation was first derived by Burton, Prim, and Slichter,' in which they assumed that a) the equilibrium distribution of solute was maintained on the plane of the interface, 11) the solute build-up ahead of the interface in the liquid disappeared at a distance 6 from the interface, and c) the solute distribution in the liquid was invariant with time. The following well-known relation between ko and ke was then obtained, where R is the rate of solidification and D the diffusion coefficient of the solute in the liquid. This equation appears to correlate the data from a number of different types of solidification experiments very well. Application of an electric field across the solid-liquid interface can produce an additional flow of solute atoms as a result of the electrotransport. When the polarity of the field is such as to direct the electrotransport flux away from the interface the solute build-up may be diminished, even to the point of producing a solute depletion and a consequent ke smaller than ko. The quantitative description of this process and the resulting form of Eq. [I] was first given by Hucke et al.1* and then inde- where E is the electric-field intensity and U is the differential mobility, i.e., the velocity of the solute atoms with respect to the solvent atoms per unit electric field. Both authors follow the method of Burton, Prim, and Slichter in their derivation, the only difference being the additional electrotransport term in the flux equation. It has been pointed out1,3 that Eq. [2] predicts the possibility of a noticeable increase in the purification of materials by solidification in an electric field. The validity of Eq. 121 has not been checked experimentally and it is possible that other factors' arising from the presence of an electric field across

Jan 1, 1965

By Michael B. Bever, Carl F. Floe

he possibility that carbon may be soluble in copper to a limited extent has bten recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are freauerltlv used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. Review of Literature In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of 0.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.9258 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been ill prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as 0.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

he possibility that carbon may be soluble in copper to a limited extent has bten recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are freauerltlv used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. Review of Literature In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of 0.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.9258 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been ill prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as 0.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1946

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

ABERDEEN, ESTHER, U. S. Geological Survey, Washington, D. C. ALLEN, VICTOR T., Director Geology Department, Institute of Technology, St. Louis University, St. Louis, Missouri. BATES, THOMAS F., Associate Professor of Mineralogy, Department of Earth Sciences, School of Mineral Industries, The Pennsylvania State College, State College, Pennsylvania. BOLGER, ROBERT C., Geologist, Pennsylvania Topographic and Geologic Survey, Harrisburg, Pennsylvania. BRIDGE, JOSIAH, U. S. Geological Survey, Washington, D. C. BURST, JOHN F., Geologist, Exploration and Production Research Division, Shell Oil Company, Houston, Texas. CAMPBELL, IAN, Executive Officer, Division of Geological Sciences, California Institute of Technology, Pasadena, California. FLINT, DELOS E., U. S. Geological Survey, Washington, D. C. FREDERICKSON, A. F., Associate Professor of Geology (Geochemistry), Washington University, St. Louis, Missouri. GLASS, HERBERT, Illinois State Geological Survey, Urbana, Illinois. GORDON, MACKENZIE JR., Geologist, U. S. Geological Survey, Washington, D. C. GRIM, RALPH E., Research Professor, Department of Geology, University of Illinois, Urbana, Illinois. HARDER, E. C., Aluminium Secretariat Limited, Montreal, Que., Canada.

Jan 1, 1952

By J. S. Marsh

OPPORTUNITY to pay tribute to the memory of Professor Henry Marion Howe is a strenuous assignment as well as an honor. Upon recalling Howe lecturers and lectures of the past 25 years, glancing over the list of those earlier, and rereading Howe's books, I arrive at several conclusions: 1—Many lecturers either worked under or knew Professor Howe. 2—It is virtually impossible to pick a subject on which Professor Howe did not touch. 3—There is precedent for a technical paper based upon pursuit of a single subject. 4—There have been listening lectures and reading lectures. There is solid comfort only in 2: the subject field is wide open. I did not know, nor even ever saw, Professor Howe, so can supply no fitting reminiscence. As a college student I was dimly aware that he counted among the giants. Fuller appreciation of his stature came with reading his books and papers, growing acquaintance with some of his associates, and the intrinsic dignity of the climax of the Annual Meeting, beginning at four o'clock of a Thursday afternoon in the auditorium of the Engineering Societies Building in New York. As for producing the technical paper sort of thing, it is my lot to have reached an age and assignment such that to do so would be to filch information from those who did the work and whose story is theirs to tell; for this I have no enthusiasm. As for the final conclusion, Professor Howe was one of the chosen few so highly expert at expository writing that he could produce a lecture or paper that reads as though it would also have listened well. One of his tricks was the free use of words not ordinarily part of the technical vocabulary, provided that such words were likely to communicate most precisely what he had in mind. How wonderful it would be for all who must read reports by the ton if ability at exposition could be taught with the effectiveness open, say to, differential calculus! Perhaps Professor Howe should be required college reading even if for no other reason than to prove that technical writing need be neither dull nor diffuse. My assignment is clearly still strenuous. Another point to consider is the fact that metallurgy is now so tremendously diversified that hope of finding a topic of universal appeal is negligible, even if one were competent enough to be permitted free choice. That which follows is, therefore, a compromise composed of necessity and of the obligation to attempt to avoid boring to slumber those of you who are not especially interested in the general subject chosen. The Iron and Steel Div. is now essentially a process metallurgy division, heavily concerned with the smelting of iron and the making of steel. The American Iron and Steel Inst. figure for present steel capacity of this country is 125,828,310 net tons; how this is divided among processes is indicated by the production totals for 1953, shown in Table I. The glamor girls and boys make the front page and so it is with steelmaking processes. If there is an Antarctic Daily Bugle, it undoubtedly has carried stories of revolutionary development, such as oxygen processes and vacuum melting, and stories of the incomparably rosy destiny of electric arc melting. All such certainly have their place and their future; meanwhile, it is the sturdy and old reliable open hearth that accounts for the bulk of production reported back on the financial page, and it is the old reliable that is most likely to continue to account for the bulk for some perfectly sound raw material, technologic, and economic reasons. This, plus the fact that next year marks a centennial (for it was in 1856 that Frederick and William Siemens conceived the regenerative open hearth), is reason enough to talk about open hearth furnaces, but is not the real one. The real reason is that in some years of association with open hearths, I have accumulated—in addition to a genuine liking and respect for them—certain odds and ends of fact and fancy that this lecture provides a unique chance

Jan 1, 1956

Discussion of the paper of N. V. Hansell, presented at the Cleveland meeting, October, 1912, and published in Bulletin. No. 72, December, 1912, pp. 1497 to 1,517. F. L. GRAMMER, Leesburg, Va. (communication to the Secretary*).:-Mr. Hansell conies from a country where charcoal is the fuel, and fuel is therefore costly. The Swedes appreciate more than most Americans the value of ore-concentration, not only in fuel-economy, but also in its influence on the quality of metal produced. Neither in these particulars nor in our knowledge of the dressing of iron-ore do I think. we can claim to be their equals. A 60 per cent. ore is not merely- twice, but more than four times, as valuable as an ore carrying 30 per cent,. Failure to appreciate this fact explains many idle American stacks, erected in defiance of it. Next to the rule that the equipment-cost of a blast-furnace increases approximately as the square of the hearth-diameter, I know of no mathematical relations involved in smelting iron which are less appreciated than the disadvantages of lean ores. Mr. Orn told me, when I was in Stockholm, that 2,500 patents on magnetic concentration had been taken out. He may have been joking as to the exact figure, but his remark indicated the great activity of inventors in this field. The magnetic separators seem to represent two main ideas, namely, wet and dry separation. The wet separators, such as the Gröndal, are applicable to ores requiring the greatest comminution by reason of the small particles of associated minerals or because of the occurrence of magnetite with a soft mineral likely to cake, as in those of Cornwall, Pa. Of the dry magnetic separators some are well suited for large-grained ores, such as those of Mineville, N. Y. We have also magnetic separators, like the Wetherill, for ores not usually classed as magnetic.

Jan 5, 1913

By Allen Garrison

IT is the purpose of this article to present. the results of an investiga-tion of certain clay and shale suspensions having viscosities that are materially influenced by fluid motion, and to discuss the bearing of these results, upon the choice of policy in the control of drilling fluids. A previous article described the design and the characteristics of an instru-ment adapted to measure the viscosity of plastic suspensions during continuous uniform motion and at a variety of speeds.1 It has long been recognized that the viscosity of a clay suspension depends on the past history of the fluid motion. Since an abundance of literature is available on this phenomenon,2 it is not necessary to describe it in more than general terms. It is usually observed that rapid motion reduces the viscosity of a clay suspension, and that some time is required for the viscosity to fall to its equilibrium value after the steady motion is started. On reducing the speed of motion to some lower value, the viscosity again rises, but it also requires some time to attain a steady viscosity value at the slower rate of motion. Thus clay suspensions are usually observed to be increasing in viscosity as time passes when the measurement has been immediately preceded by fluid motion that was more rapid than that employed in the measurement. And it is usually observed that the viscosity falls as time passes when the measurement has been preceded by more quiescent conditions. Reed,3 and Broughton and Hand4 have reported a condition of observa-tion of clay suspensions in which the viscosity was observed to fall during the first few moments of steady motion, and rise thereafter. The characteristics of the new instrument are particularly well adapted to studies of this kind. With it we have been able to observe all of the phenomena described above, and it is important to understand their nature because they all occur at some time during normal drill-

Jan 1, 1939

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in. the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson -and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix.12 This practical use of a certain knowledge as to the things that influ-ence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the harden-ing treatments of high-speed steels,14,15 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

By S. F. Shaw

The theory that maintaining a high back-pressure on the oil sand lowers the viscosity of the oil has been generally accepted. The theory has also been advanced that lower viscosity permits the oil to be moved through the sand to the well at an expenditure of less gas per barrel of oil than would otherwise be required. It seems reasonable to assume that production of oil at the minimum gas-oil ratio will result in a greater ultimate recovery of oil. During the past five years the writer has acquired data on thousands of tests made on wells to determine the best rate at which to produce them. In the majority of cases reduction in back-pressure did not definitely increase the gas-oil ratio. The information obtained from these tests has raised doubt in the mind of the writer as to the correctness of the theory that lowered viscosity results in lower gas-oil ratios and in higher ultimate recovery of oil. The reasons that explain the results obtained in these tests cannot yet be definitely stated, but the hypothesis is being tentatively assumed that there are other factors which outweigh the influence of viscosity. Energy in Gas Moves Oil to Well The general opinion is that in most cases it is the energy in the gas that moves the oil to the well. In wells flowing naturally it is also the energy in the gas that lifts the oil to the surface. In a flowing well, there are two very distinct operations: 1. Moving the oil through the sand to the well. 2. Lifting the oil to the surface. The more important function of the gas is that of moving the oil to the well. Means for lifting the oil can always be found once it has been delivered to the well. Principles Involved in Lifting Oil A well that flows naturally is the same as a gas-lift well except that all of the gas is supplied by the oil reservoir. This natural flow is subject

Jan 1, 1931

By M. J. Sinnott, W. R. Kiessel

The creep characteristics of commercially pure titanium sheet in the annealed state, cold-worked state, and cold-worked and recovered state in the temperature range from 75' to 750°F have been determined. Titanium has been found to exhibit strain aging characteristics. The effect of strain aging on creep has been determined. A possible explanation for the poor creep properties of titanium is proposed. THE metal titanium exhibits many desirable properties but results on its creep properties have been somewhat disappointing. The creep strength is low even though the material has a very high melting point.' The present work was undertaken to determine the creep strength of titanium in various conditions; annealed, cold-worked, and cold-worked and recovered and to determine why titanium shows such relatively poor creep properties. The general procedure followed in this research consisted in obtaining the usual mechanical prop- erties such as creep strength, short time tensile strengths, and hardness on materials treated to a controlled degree of internal strain, as determined by X-ray diffraction measurements, and their subsequent interpretation in terms of this internal strain. The material used in this work was sheet stock taken from one heat of commercially pure titanium. As-received, this sheet was 0.060 in. thick. The analysis was given as 0.037 pet C, 0.023 pet Si, 0.50 pct W, 0.063 pct Ni, 0.08 pct Fe, and the remainder titanium. The oxygen and nitrogen were unreported but generally are about 0.2 pct in commercial heats. In order to put the material in a state of minimum internal strain all the sheet was given an anneal in a static argon atmosphere for 1 hr at 1600°F prior to processing and testing. The microstructure of the material after this treatment was essentially a single-phase solid solution of uniform equiaxed grains. For the studies on the cold-worked sheet, the material was reduced by rolling in a two high, 5 in. mill. Rolling was done at room temperature in passes

Jan 1, 1954

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By Wilson D. Michell

The Magma copper vein trends east-west, dips 70" south, and cuts through a 6000-ft thickness of limestones, quartzites,. shale, diabase, and schist. The vein is itself a fault with a horizontal offset of 500 ft on the formation contacts in the two walls. There are two principal faults of large displacement and numerous smaller steep and flat faults that complicate the prediction of ore occurrence. A study of the geology, its systematic recording to facitliate ready reference, and graphic methods of interpretation of mineralization have aided the exploration, development, 2nd mining of the ore. In making predictions of the distribution of mineable ore bodies and their shape in critical areas, studies are made of "mineralization contours" and "mineralization trends," which are developed on a longitudinal section of the vein from variations in the concentration of the combined base metal content as shown by assays of available openings in the mine. Introduction This paper describes an example of geological work applied directly to mining and exploration problems in a deep vein deposit, and it is presented as being of interest especially to those engaged in working more or less similar veins. In 1944 to 1945 the writer spent a year as assistant to J. K. Gustafson in a thorough geological examination of the Magma mine. Much of the writer's subsequent independent work described in the present paper had its inception in ideas originated by Gustafson during that examination. Objectives of Geological Work at Magma Mine The objectives of geological work at Magma, as at operating vein mines of a similar nature, can be summarized as follows: 1. Direct assistance to the mining department by means of predictions as to the size, shape, grade, and location of ore bodies; by solution of fault problems and irregularities in the veins; by prepara-?ion of detailed ore-reserve estimates in specific areas; by keeping a complete record of the geology and assay results in the mine; and by guiding development work. In short, geology can aid in the realization of the prime purpose of the mining department, which is that of producing the greatest amount of ore in the most economical and expeditious manner possible. 2. Guidance for exploration, especially diamond drilling, in undeveloped areas of the mine. 3. Contributions to the understanding of the general geology of the deposit and its regional setting, including ore genesis, structure, and mineral relationships. Magma Ore Deposit The east-west trending Magma vein, dipping about 70" south, cuts through a 6000-ft thickness of concordant limestones, quartzites, shale, diabase, and schist, named in descending order. These

Jan 1, 1949

By T. E. Leontis, F. N. Rhines

THE oxide scale that forms upon magnesium at elevated temperatures is nonprotective in the sense that the rate of oxidation is constant and thus does not decrease with the growth of the scale as it does with other common metals. This generality was first stated by Pilling and Bedworth1 and has been verified by Suzuki2 and by Scheil.3 Pilling and Bedworth argued that the nonprotective characteristic could be predicted from the fact that magnesium oxide occupies less space than does the metal from which it springs, wherefore the scale is not expected to cover the metal so completely as to exclude all direct access to the atmosphere. Linear oxidation is thought by Scheil to be common to all cases where the reaction occurs at the oxide-metal interface. According to Suzuki,2 the product of high-temperature oxidation in the air is MgO contaminated with no more than traces of a nitride. When the metal is allowed to burn freely a fume composed of cubic crystals of Mg04 is given off. Delavault5 observed that excrescences form upon liquid magnesium and alloys in the course of oxidation. Beyond this it is known that the use of atmospheres containing small quantities of sulphur dioxide6 or carbon dioxide serve to retard the oxidation of solid magnesium and that beryllium7and calcium8 minimize the oxidation of molten magnesium exposed to the air. Many studies have been devoted to the nature and rates of "protective" oxidation, as exemplified by the cases of copper and iron, wherein the rate is characteristically parabolic. The theory of parabolic oxidation is well developed.9 Linear oxidation, on the other hand, has received but little attention and the theories proposed by Pilling and Bedworth and by Scheil have yet to withstand careful examination. There exists no comprehensive survey of the high-temperature oxidation of magnesium (or of any other metal that exhibits linear oxidation) over a broad range of temperature, under a variety of atmospheric conditions and covering a large group of alloys. It has been the purpose of the present investigation to provide such a survey, with the object of gaining a fuller understanding of linear oxidation, especially as applied to magnesium. EXPERIMENTAL PROCEDURE AND RESULTS The experimental studies undertaken were of two kinds: (I) measurement of the rate of oxidation as influenced by the

Jan 1, 1946

By R. P. Rothwell

The milling of silver ores has arrived at a great degree of perfection in the mining districts of our Western States and Territories, and I hare thought the record of the practical results obtained at the present time, in a few of the principal districts, would prove of value arid interest to many of our members, both at home and abroad. An American silver mill is composed, in descending order from where the ore is dumped, of: 1st. A rock-breaker, usually of the Blake or Alden pattern; 2d. The battery of stamps, the number of which varies from 5 to 120, generally in batteries of 5 or 10 heads, so arranged that a single battery may stand while the others are running; 3d. The tanks where the crushed ore settles (if it is a met stamping-mill), or of a drying-floor if the crushing is done dry; 4th. Amalgamating pans ; 5th. Settling pans ; 6th. Agitators or pans in which mercury escaping in the tailings is caught; 7th. Blanket sluices, over which the tailings run, and where mercury and unamalgamated sulplides are saved. A reference to the engravings (see plate), which show one of the latest forms of an 80stamp silver-mill run by a turbine water-wheel, will show clearly the arrangement of the several parts. THE ONTARIO, UTAH, SILVER MILL. One of the best examples of a silver-mill, and at the same time one of the most successful concerns in the West, is the mill of the Ontario Silver Mining Company, near Salt Lake, in Utah. This mill treats the ore from the Ontario mine, ore which at present is very base, being composed of zinc, lead, and silver sulphides and silver chloride in a quartz gangue. This ore has become baser as the mine attained greater depth, though the vein holds its own, or rather increases, both in thickness and richness. The mill is managed in a skilful and economical manner, though the necessity for

Jan 1, 1880

By D. M. Urich

New plant construction for pyrolysis and agglomeration during 1969 has been relatively quiet in the North American scene. U.S. pellet capacity approximates 52 million long tons and that of Canada 25.3 million tons. The foreign scene, however, has been extremely active during 1969, and this is expected to continue for the next several years. Changes in sinter practice have not been reported, other than a few changes towards increased bed depths and the increased use of screening facilities to size the product more closely. Interest in the field of briquetting in fields other than iron ore is high with a new fluorspar briquetting plant under construction at Brownsville, Texas. Considerable research appears to be pointed towards solving the problem of reclaiming steelmill waste products (flue dust, BOF dust, mill scale) by means other than sintering.

Jan 1, 1970

By A. Vignes, J. P. Sabatier

A study of ternary diffusion at 1315°C in the Fe-Co-Ni system covering the entire ternary phase diagram has been carried out. Experimental values of the four interdiffusion coefficients DFeNico,DFeCoCo, DFeCoNi were computed at 33 points of the ternary diagram. The limiting values of these coefficients on the three sides of the ternary diizgram have also been determined. This set of data is presented as a contour map on the ternary isotherm for each of the four coefficients. Assuming that the Fe-Co-Ni system can be considered as ideal, the phenomenological coefficients Lk ij (with k = Fe) have been computed and the Onsager reciprocal relutions verified. It is shown that, in the Fe-Co-Ni system, the diffusion process can also be described by only two interdiffusion coefficients DFeFe and DCoNiFe, the second cross diffusion coefficient DCoFeNi being equal to zero and the second direct difusion coefficient being given by The values of the cross interdiffusion coefficients and of the Onsager coefficients are explained in terms of atomic mobilities of the three components with the help of a kinetic calculation due to Lane and Kirkaldy.8 It is shown that all the results are explained if the tracer difusion coefficients of the three components are such that DFe > DNi ~ DCo in complete agreement with experimental data on the three binary systems. DIFFUSION in a ternary alloy system is basically and significantly different from diffusion in binary alloys. In binary diffusion, there is just one independent composition variable and only one coefficient Dij is needed to describe the interdiffusion process. In ternary diffusion, we must allow for cross interaction between two independent species, and four interdiffusion coefficients are necessary to describe the transport process. Kirkaldy et al.1,2 have determined interdiffusion coefficients in the systems, Cu-Mn-A1 and Zn-Cu-Al. Guy and Leroy4 have reported intrinsic diffusion coefficients for the r phase at 1300°C of Co-Ni-Cr alloys as a function of composition using the analysis of Philibert and Guy.3 Interdiffusion coefficients were measured at three different compositions at 850°C in the single phase copper-rich corner of the Cu-Zn-Mn system by Dayananda and race.5 Zie-bold and Ogilvie6 have determined interdiffusion coefficients in the single-phase field of the Cu-Ag-Au system at 725°C. Preliminary results on diffusion at 1136°C in the system Fe-Co-Ni have been reported.7 In this study, data are reported on a more complete determination of interdiffusion coefficients in the Fe-Co-Ni system in the entire ternary at 1315°C. There is complete solid solubility with the fcc structures at 1315ºC, and this system can be considered as nearly ideal. This approximation allows the computation of the Onsager phenomenological coefficients. These values can then be used to test a kinetic calculation of the Onsager L coefficients in ternary substitutional solid solutions due to Lane and Kirkaldy.8

Jan 1, 1970

By Henry Howe

1. The purpose of the National Research Council as organized for war purposes is twofold, to stimulate those outside its own personnel to conduct researches of importance for winning the war and to carry on such researches through its personnel to a limited extent. How this is clone is explained in Section 10. "Research" is used here in a very broad sense, including, for instance, inventing and developing mechanical and physical devices. The need of this work arises from the inevitable concentration of most of the governmental war agencies on the production and transportation of war materials of. the types now adopted, as distinguished from devising new kinds of instrumentalities, such as armor, guns, aircraft, and apparatus for detecting, locating, observing, signaling, transporting, and many other military purposes. But it is important that we should devise new agencies. The war came near being won by an invention, the submarine, and its course has been affected greatly by two other inventions, tanks and aircraft. In spite of our numerical superiority victory may well be snatched from us by an invention, if we allow Germany to outstrip us in inventing. Hence the importance of the Council's work in mobilizing and organizing the services of the patriotic civilian experts throughout the country, so as to bring their powers to bear on important war problems and on inventing war devices, as an adjunct to the development work of the regular governmental bodies. 2. Status of the Council.-Though President Wilson's request caused the Council to be created by the National Academy of Sciences under its congressional charter in 1916; though his executive order of May 11, 1918, directs the heads of "Governmental departments immediately concerned" to "continue to co-operate with it in every way that may be required;" and though the Government has contributed largely to its financial support (Section 12, page 10), it is not a department of the Government but an independent research body, aiming to evolve the necessary mechanism for the novel work of systematic stimulation and guidance of research. Thus the Government, which instigated the creation of the Council, recognizes and collaborates with it, and in part supports it. The Council acts moreover as the Department of Science and Research of the Council of National Defense.

Jan 12, 1918

By S. F. Shaw

The Seminole field was first drilled in 1913. During the next 10 years other attempts were made to discover oil in this field, but without encouragement until March, 1926, when the Indian Territory Illuminating Oil Co. completed NO. 1 Dyer in the Hunton lime for 1100 bbl. On July 16, 1926, the Independent-Garland interests discovered oil in the Wilcox formation when No. 1 T. Fixico came in at 4055 ft. and on Sept. 9, 1926, production reached a peak of 8040 bbl. On Aug. 1, 1927, the daily production of the pools making up the Seminole district amounted to slightly over 500,000 bbl., practically all of which was coming from the Wilcox formation. The Hunton formation has not been very productive of oil, but has maintained a fairly high gas pressure; this formation has been encountered at from 3800 to 4200 ft., below which there is about 100 ft. of Sylvan shale. The shale is underlain by 75 ft. of Viola limestone in a few places in which formation oil has been encountered. Below the Viola lies the upper Simpson formation in which is found the Wilcox sand. The depth of the Wilcox in the Seminole field varies from 3900 to 4500 ft., and initial production has reached as much as 12,000 bbl. The gravity of the oil is about 41° Be. The general practice is to set 6 5/8 -in. casing above the Wilcox and drill in, though in several cases 5 3/16-in. casing has been set for the oil string, and in a few instances, casing as small as 4 3/4 in. has been employed. Production Statistics Production for the Seminole district for the various months since its discovery is shown in Table 1.

Jan 1, 1928

By F. H. Labee

Questionnaires and special letters soliciting information were sent to a great many geologists, petroleum engineers, independent operators, and representatives of large companies in Arkansas, Louisiana, Texas and New Mexico. Replies to more than 50 per cent. of these letters were received. A survey of the facts and opinions presented in this correspondence will be made a little later, but first some of the general aspects of the problem will be reviewed. By "unit operation,"1 we mean the development and operation of a single entire pool, or reservoir, of petroleum by one management, on a systematic and scientific plan which is best calculated ultimately to extract from the pay sand and bring to the surface of the ground the largest possible amount of oil with the greatest possible total profit. No one, as far as the author has been able to ascertain, denies the advantages, both scientific and practical, of unit operation. All are agreed that it is sound in theory. It permits the proper distribution of wells, which should always be spaced on the ground according to a regular geometric plan with the intention of maintaining the same spacing all the way down and into the pay sand, or pay sands. This spacing will be different for different fields, depending on such variable factors as the lithologic character of the pay formation, the nature of the controlling structure, the depth of drilling, the viscosity of the oil, and so on. From the viewpoint of engineering practice, as applied to economical extraction of oil, there is no more important consideration than well spacing—well spacing in the pay formation, and not merely on the surface of the ground —for the method of well spacing has a direct bearing upon all such engineering practices as pressure control, repressuring by gas, the water drive, and SO on. H. C. Miller2 summarized the advantages of an ideal cooperative development plan as follows: "Among the more important advantages of

Jan 1, 1930