Search Documents

By George D. Roberts

Civil engineers are primarily interested in maximum core recovery. This is even more important in foundation work than in mining investigations where sludge samples are of some value. The soft materials, such as clay, gouge, or partially decomposed seams that are most readily ground up or washed away, are the materials that usually have the greatest influence on foundation and leakage conditions. Undisturbed samples of such materials should be obtained for detailed geological examination and laboratory tests. Therefore the attainable goal of sampling in connection with foundation investigations is the recovery of 99.9 pot of undisturbed core. Factors Causing Core Losses The principal factors contributing to core losses are: (1) coring badly fractured or very soft material; (2) Use of improperly designed coring equipment, including the use of bits of too small a diameter; (3) lack of the proper training and attitude on the part of the drillers and pertinent technical information on the part of the supervising personnel. Little can be done about the character of the material being cored but the other two factors contributing to unsatisfactory performance can be corrected. Although the title of this Paper is the improvement and standardization of core barrels, it is believed that the drillers' shortcomings and the lack of pertinent technical literature are more detrimental to good core recovery than either of the other factors. Uses For Large Diameter Core Barrels It is well known that the use of larger diameter bits and core barrels generally produce better cores, particularly when sampling soft or broken material. The use of larger and larger bit diameters and the insistence on better core recovery is well demonstrated by the change in practices of the various districts of the Corps of Engineers. Today NX core is the smallest diameter commonly permitted for investi-gational work and the more active districts are using coring bits up to 6 in. in diameter, as well as 36 and 40-in. calyx rigs. The latter size has proved to be just as economical because it provides more room for ctured removal and cleanup operations. The use of large diameter cores to replace the driving and jacking methods of obtaining soil samples is also increasing. The 57/8-in. Denison sampler, developed by H. L. Johnson to obtain samples from soft formations, is one example. The principal uses for bits larger than NX are: sampling soils and semi-consolidated rock; sampling decomposed rock or rock with soft seams; sampling concrete; obtaining samples for laboratory tests; drilling drainage holes, and other miscellaneous work. Core Drilling Practices of Several Engineer Districts Little Rock District The writer was employed in the Little Rock District from 1938 until 1942. Prior

Jan 1, 1949

By J. E. Smith, P. B. Crawford, B. L. Laudrum

A method is presented by which the displacement efficiency of a steam-injection process may be determined. The method consists of a determination of the position of the steam front at a particular time and the application of the Buckley-Leverett theory to the hot and cold regions of the reservoir with the appropriate hot or cold fluid properties. A uniform, linear flow system is assumed for this study. The method is applied to a number of reservoir conditions. The primary properties which affect the results of a steam-injection process are the oil viscosities at steam and reservoir temperatures, injection rate, pay thickness and oil saturation. The efficiency of steam injection is compared with that of water injection for a 10-acre, linearly flooded reservoir. In reservoirs where the oil viscosity is about 35 times the water viscosity, the steam process yields recoveries about 20 per cent higher than the water flood. Where the oil viscosity is near 500 cp, the steam process may recover from three to four times as much oil as a water flood. INTRODUCTION In a previous paper,' a method was suggested for evaluating a steam-injection process. Emphasis was placed upon the determination of the steam-front position in the reservoir at various times. In the present paper, the displacement process is studied in more detail. The approach is essentially that employed by Jordan, Rayne and Marshall3 in their study of hot-water injection. The steam-injection process is quite complex, and an exact description of the process has not been found; however, a qualitative description can be made. When a quantity of steam is injected into a relatively cold reservoir, the leading edge of the steam front continaally flows into cool sand, and some steam condenses. As more and more steam condenses, a bank of condensed water will form which is augmented by displaced connate water. The reservoir may be divided in three regions—(1) a region containing displaced fluids at reservoir temperatures, (2) a region contain- ing water at reservoir temperature and (3) a region occupied by steam. The reasons for the lack of a region of hot water or oil of any appreciable size have been discussed.' A method has been presented by which the location of the steam front can be determined even when heat losses to the regions surrounding the reservoir are sizable compared with the amount of heat injected. It remains to show the effectiveness of steam injection in increasing the ultimate oil recovery. To illustrate the technique for determining the increase in displacement efficiency and, hence, the increase in ultimate production, two sets of hypothetical reservoir conditions will be studied in detail.

By Nick Holonyak

Halogen vapor-transport synthesis of Ga(As,-,Px) and its preparation into laser junctions are described. Electrical and optical properties of Ga(As,-,PX) laser junctions are discussed. The present limitations in these properties are related to material proble?vzs and the very early state of development of Ga(As,-,PX), and are discussed in this context. Inhonzogeneity problems, fluctuation of As :P ratio, and problems with deep-level contaminants are described and related to Ga(As,-,PX) junction performance. Laser junctions are demonstrated which operate to wavelengths as short as 6470 A (77°K). The prospect that Ga(As,-,P,) will operate to wavelengths perhaps 100A shorter is mentioned. IN this paper we wish to describe some of the more important features of almost 1 year of experience in the preparation and properties of Ga(As,-,P,) p-n junction lasers. Because much data so far available are far from complete, some of the results still must be considered tentative and subject to correction and revision as work on Ga(As,-,P,) crystal problems progresses. Although the electrical, optical, and device properties of Ga(As,-,P,) junction lasers are understandably of considerable interest, the work to date points out that by far the most serious problems extant and those deserving first attention are problems involving the growth, doping, and perfection of Ga(As,-,P,) crystals. One of the most formidable of these is to grow Ga(As,-,P,) sufficiently free of deep levels, either due to contaminants or to structural imperfections, to allow fabrication of laser p-n junctions which can be cooled and not suffer from "freeze-out" of carriers on deep levels (and consequent double-injection behavior). In addition to the problems of growing crystals adequately free of deep levels and generally of the highest perfection, so that the best possible laser junctions can be realized, the further goal remains of increasing the phosphorus content well beyond 40 pct in an attempt to determine the practical lower wavelength limits of laser action in the Ga(As,-,P,) system. Even though the laser junctions prepared in Ga(As,-,P,) are of importance in their own right, we have considered them at this point mainly a means to study the growth and crystal problems of the material. It can be concluded that the laser junctions now available are almost completely limited by the purity and structural deficiencies of Ga(As,-,P,) crystals, and cannot be fairly compared with, for example, GaAs p-n junction lasers until Ga(As,-,P,) crystal growth has been more extensively developed. The basis for the statements above will become evident in the following sections which describe Ga(As,-,P,) crystal and junction preparation, and laser-junction properties. G(As,-,P,) CRYSTAL GROWTH As previously reported,2 we have found it convenient to employ the halogen vapor-transport process3 for synthesizing Ga(As,-,P,) crystals for use in laser junctions. Commercially available GaAs and Gap, separately prepared by halogen vapor tranport, are sealed in the desired ratio in a quartz vessel with a quantity of column-VI donor and a small quantity of metal halide which supplies the halogen for transport. The sealed ampoule, as shown in Fig. 1, is heated at a temperature in the range from 1025" to 1100°C at the position of the source GaAs and Gap. The GaAs and Gap are simultaneously vapor-transported and deposited as Ga(As,-,P,) at one end of the ampoule

Jan 1, 1964

By W. H. Nielson, L. S. Diaz

Several techniques are presented to adjust small errors inherent in data collected from material balance measurements on the flotation process. The basic technique used is a Lagrange multiplier adjustment of the filtered data taken from the equipment measurements. The raw data are adjusted such that material balances are closed. The adjustments to each data point is inversely proportional to the square of the standard error of measurement. Problem areas in equipment utilization are discussed. Typical results from on-line measurements are presented. This technique can be applied to either on-line process measurements or metallurgical test data.

Jan 1, 1973

By Herbert H. Uhlig

A STUDY of passivity in chromium-iron alloys holds considerable interest, both because of the present-day practical importance of the stainless steels, and because of the scientific importance attached to the mechanism of their corrosion resistance. Upon the discovery of the passive chromium-iron alloys in 1912, it seemed logical to attribute the observed phenomenal corrosion resistance to a thin, continuous, protective reaction product on the surface. The product was thought to be Cr2O3 or a similar oxide containing both chromium and iron. This mechanism seemed likely in view of Michael Faraday's conjecture that passive iron is not reactive in concentrated nitric acid because of an oxide on the metal surface.† Since 1912, data have accumulated that permit a further exploration into the nature of passivity and provide a new approach to the problem. A summary of the facts lends considerable weight to a mechanism based not on physical protection of an oxide or similar compound, although such compounds may be present on the surface, but to a change in tendency of surface metal atoms to react chemically. This change in reaction tendency is ascribed to chemisorbed films that effectively satisfy residual valence forces of the metal surface, but do not appreciably disturb the positions of metal atoms in the lattice. In other words, formation of a new lattice such as that of an oxide is not a necessary condition for this type of passivity. The decreased reaction tendency of the metal by reason of chemisorbed films can thereby account for low reaction rates of the stainless steels in many media, as well as a noble galvanic potential as is observed. Substances capable of adsorbing on the stainless steels, and hence accompanying the property of passivity, are typically oxygen, nitrites or chromates, but are not in any sense limited to these. Other elements and compounds can also chemisorb, and therefore may also play a major part in the mechanism of passivity in specific media. The mechanism of passivity based on chemisorption or activated adsorption begins with the interpretation Langmuir proposed for his experiments concerning adsorbed oxygen on tungsten.1 He found that adsorbed oxygen was tightly bound, remaining on the tungsten surface above temperatures at which WO3 rapidly volatilizes. The oxygen in such a state did not readily react with hydrogen even at

Jan 1, 1947

By F. Lynwood Garrison

The study of the microscopic structure of the iron of car-wheels, which it is the aim of this paper to describe, was made at the suggestion of Dr. Dudley, whose paper upon the constitution of cast-irons (page 795 of the present volume) should be read in connection with this one. Although the two wheels referred to in that paper possess nearly an identical ultimate chemical composition, they possess, as Messrs. Dudley and Pease have shown, physical properties so widely different, as to make one of them nearly worthless for the purpose for which it was cast. Considering the chemical similarity, such a marked difference in strength cannot but be very striking, and goes to show how little reliance can be placed upon chemical analysis alone, if not properly interpreted. I say " not properly interpreted," because I believe that very few analyses of iron or steel are thus fairly dealt' with. That an analysis may read so much of one thing and so much of another, tells us very little as to the properties of the metal; for these are determined to a large extent by the conditions and relations in which the elements are present. To the unaided eye the difference between the two wheels under consideration is not striking. The inferior one would be described as light gray, and the other as somewhat darker. Upon careful examination of an etched fragment, however, the difference in structure will be found to be very marked, as may be seen in Figs. 1 and 2 (produced from photographs by the Ives process). It is exceedingly difficult to produce a photograph giving a fair notion of the appearance of the metal under the microscope, so as to give to persons not familiar with microscopical study, a proper appreciation of what a microscopist would consider a decided difference in structure. I would, therefore, urge any one especially interested in this subject, not to depend upon the photographs of others, but to prepare and etch the specimens himself, and then examine them with a good microscope. As is well known, iron possesses the property of uniting with a number of elements, forming products which are either highly intimate mixtures of several substances, or else compounds of an indefinite character. Indeed such mixtures may be regarded as alloys, or as Matthiessen puts it, " solidified solutions of one sub

Jan 1, 1886

By W. M. Bertholf

IN 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral can make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory," as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,1 but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1946

By Roland W. Rammler

With oil consumption increasing more rapidly than known reserves in industrial countries, there has been a growing interest in the production of synthetic crude oil. The main starting materials for such production are coal, oil shale and tar sand, all of which occur in enormous quantities in North America. A process sequence suitable for all three of these starting materials incorporates a preliminary retorting step to produce oils for subsequent hydrotreating. For this retorting step, a technique known as the Lurgi-Ruhrgas process has proven highly efficient. The process has been commercially used for the flash carbonization of coal and has also been tested in pilot- plant experiments with oil shale and tar sand.

Jan 1, 1970

The co-operation of the. members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give, them full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President: Two officers, known as Director and Vice-President. Five officers, known as Director. The officers of the Institute whose terms expire are as follows: President, William L. Saunders (not eligible for re-election). Past President, Charles F. Rand. Vice-Presidents, Thomas H. Leggett, District 0; Fred W. Denton, District 4.

Jan 10, 1915

By Arthur V. Abbott

TO rightly use materials, two kinds of knowledge are essential: first, the actual strength of the substance; and secondly, the forces to which, in the structure, it may be subjected. Nearly all of the data which we have at the present time have been obtained from the experiments made on the materials used in Europe, and by foreign investigators. The materials commonly used in this country, es-

Jan 1, 1884

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) The governing body of the Imperial College of Technology, London, S. W. (Royal School of Mines), will shortly proceed to the appointment of a Professor of Metallurgy. This important Chair has been filled in the past by such eminent metallurgists as John Percy, Sir William C. Roberts-Austen, and others. A large manufacturing company having two iron foundries, blast furnace, etc., requires the services of a chemist, metallographist, and metallurgical engineer qualified to give advice on cast iron practice, and to prescribe remedies for difficulties often met with in the usual iron foundry. The position of converter blower at a side-blow Bessemer steel casting plant is vacant.

Jan 5, 1913

By W. R. Webster

Opinions still differ widely concerning the requirements, chemical and physical, which should be expressed in specifications for steel rails, in order to secure results satisfactory to both manufacturers and purchasers.

Jan 1, 1902

By F. L. Grammer

In these day, when anthracite is less extensively used as a blastifurnace fuel than it was a generation ago, and managers endeavor to maintain regular and known ore-mixtures, the " freezing " of tuyeres, cinder-notch or iron-notch is infrequeut; and, consequently, the oil-burner or " kerosene blowpipe "* is seldom employed; and furnace-foremen have, to a considerable degree, forgotten their former cunning and persistency in the use of the drill and sledge. Still, in starting new or abandoned plants with untrained labor, and in running some of our large 100-ft. furnaces, slips, resulting in very cold furnaces, may occur, even under experienced managers. During my superintendence of the Cleveland, O., blast-furnaces, such a misfortune, owing to a dearth of trustworthy foremen, was experienced; and our electrician, Mr. Thomas Martin, proposed to open the tuyeres and cinder-notch by means of the heat of the electric arc. We have heard that the surface-cracks or marks developed in rolling heavy plates have been closed by electric welding, as by a soldering-iron, and also that an electric burner has been employed at some German blast-furnaces; but the experiment was quite novel to us; and I think it constituted one of the first, if not the very first, successful application of this device, for the purpose named, in the United States. †

Jan 1, 1902

By James J. Olson, Richard A. Dick

Blasting practices have shown a recent trend toward larger blastholes and larger burdens and spacings, although some operators, after reconsidering the situation have gone back to smaller blasthole sizes. The greater pull-down capabilities of larger drill rigs and the greater bearing strength of large diameter drill bits give penetration rates for large diameter blastholes approaching, and sometimes exceeding, penetration rates for smaller holes. In practically all cases, large diameter holes can be drilled more quickly and cheaply, based on volume of hole, than small diameter holes. The industry's shift to dry blasting agents and slurries, products which perform more dependably and efficiently in larger diameters, gives an additional advantage to larger boreholes.

Jan 3, 1972

By Su Zhen

Based on the technical features of the Feng- huang-shan concentrator, the authors have designed a new scheme for optimal search and self-adaptive control in flotation process, in order to apply computer control to the concentrator. Hence, a plant test of optimal control in bulk flotation of copper and iron sulfides was successfully carried out. The control parameters are xanthate addition, pulp level, and amount of aeration, etc., in flotation cells. Two mathematical models of multiple parameters established by the authors were adapted and flotation efficiency was used as an objective function in the control.

Jan 1, 1984

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By G. C. Weaver, G. T. Harley

Beds or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the rehery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3- ft. cable or rotary tools are used to drill down to the salt. when samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16 in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in. line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to Occur from nitrogen gas trapped under the several polybalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically loo per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon* and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of Ore beds between drill holes is briefly described. Introduction Beds Or lenses of potash and magnesium salts are found at varying depths in a thick deposit of salt (Salado formation) in what is known as the Permian Basin, in southeast New Mexico and West Texas. The Salado formation is Composed chiefly of common salt (halite) with numerous beds of anhydrite, polyhalite, and the soluble potash minerals carnallite, sylvite and langbeinite. Many other minerals are present in small amounts but their Presence has no bearing On the coring technique. Before starting to core the salt section it is necessary to penetrate 300 to 600 ft. of unconformably overlying Permian sediments (Rustler formation) which are composed of red and gray clay, sand, anhydrite, dolomitic limestone and occasional lenses of salt. The upper part of the formation is predominantly anhydrite, and the lower part predominantly clastic. A thin bed of dolomitic limestone, known

Jan 1, 1948

By McCall. F. E., J. Cervik, A. A. Campoli, P. Thakur

The cross-measure borehole system is a common method of controlling gob gas throughout Europe. Drainage holes are drilled into the strata adjacent to the coalbed being mined. Removal of the coal on a longwall panel relaxes and fractures the adjacent strata, enabling these holes to draw out the methane. A test in the Upper Kittanning Coalbed demonstrated the capture of 50% of the total methane generated by the mining operation. A test in the Pittsburgh Coal bed was not as effective.

Jan 1, 1985

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946

By Walter Miller

BY the beginning of 1945 the output of petroleum products for war had reached a volume and a rate of growth which practically assured all requirements so long as war continued. The programs for making gasoline, lubricating oils of required quality, toluene for T.N.T., and chemicals for manufacture of synthetic rubber, as well as numerous other lesser petroleum products, were all well in hand, and unless catastrophic developments occurred there was no doubt of the ability of the industry to meet all demands. The end of the fighting found the refining industry working at top capacity on war commodities, but also in position to convert quickly into peacetime civilian production. 100-octane Aviation Gasoline Production of the vital 100-octane aviation gasoline, starting with approximately 44,000- bbl. daily capacity at our entry into the war, reached a top of 525,000 bbl. a day in the United States by the end of hostilities. With 75,- bbl. from other Allied sources, the grand total was 600,000 bbl., or 25,000,000 gal. each 24 hr. available to the armed forces had fighting continued. At times it was a close race between requirements and production, but never were any important military operations involving the use of high-octane aviation gasoline held up or delayed for lack of sufficient output of such material. The undivided effort of the entire refining industry in full cooperation with the Government made this record possible. Little diminution in output followed the German surrender on May 7. Plans called for a correspondingly greater activity for the Japanese war and possibly for well into 1946. But when the Japanese sued for peace on Aug. 10 most contracts were quickly canceled. Substantial stocks, reputed to be somewhere between 20,000,000 to 30,000,000 bbl., built up largely between V-E and V-J day pending organization of the larger Japanese war program envisaged after Germany gave up, were in the Government's hands in this country, in addition to working stocks in the war areas. Toluene and Lubricating Oil Requirements for toluene for T.N.T. increased rapidly as bombing speeded UP with increasing control of the air by the Allies in Europe and Asia. Production in excess of T.N.T. requirements which had been going into 1000-Octane aviation fuel blending during 1943 and 1944 was again drawn into explosive manufacture early in 1945. In anticipation of the war continuing into 1946, two new plants were ordered constructed, the decision being announced in April, plans calling for one of them to get into production about the end of 1945, the other in the first quarter of 1946. Both of these projects were later canceled as victory made it evident that the additional supplies would not be needed. Production was

Jan 1, 1946