Search Documents

By D. W. Fuerstenau

On page 1243, column 1, the first line of the author's reply should read "D. W. Fuerstenau (author's reply)---," rather than D. E., as printed. In the sentence immediately preceding the first equation (page 1243, column 2)' the word "none" was omitted. The sentence should read: "However, if enough ore is put into the mill [so] that none of the energy put into the mill is wasted on metal-to-metal impact, then the product should have size modulus determined by the relation: ..."

Jan 1, 1961

By A. P. Cohen, D. W. Fuerstenau

Methods of accounting for the feed size in analyzing the size distribution shift during comminution have been discussed in a number of papers.1,2,3 Based on experiments which charles2 performed with single Pyrex specimens, Schuhmann4 pointed out that the size modulus of an assembly of particles should be determined by the energy expended per unit volume (or mass), independent of the size of particle being comminuted. In this same paper, Schuhmann derived the Charles energy-size reduction relationship by considering that complex comminution operations can be considered to be the summation of many individual comminution events, each of which must be governed by Were 6wi is the mass of a particle receiving the impact, 6Ei is the energy delivered to the particle, ki is the size modulus of the product resulting from the impact, a is the distribution modulus of the assembly of particles, and A is a constant. Recent experiments on the compression loading of Pyrex spheres ranging in size from 1/8 to l-in. diam have shown that the size modulus of the fragments is determined by the strain energy at fracture per unit mass, independent of sphere diameter.' The objective of the present investigation has been to determine experimentally whether the size distribution of the product from such a complex comminution process as rod milling is determined only by the energy expended per unit mass independent of feed size. Samples of each Tyler sieve fraction ranging from 4x6 to 48x65 mesh were prepared from crushed Brazilian quartz crystals. One kilogram of each fraction was ground at 60 pct solids in an 8x9 1/4-in. mill containing 17.5 kg of rods (26 rods, 5/8-in.; 10 rods, 3/4-in.; and 5 rods, 7/8-in. diam). In each test, the mill was run at 77 rpm for 15 min. Size distributions were determined by a wet-dry sieving technique. Table I presents the size distribution of the products obtained by grinding each of the size fractions. Because the size distributions are so nearly alike, they are plotted in Fig. 1 by shifting each size distribution for the different feed sizes one screen fraction to the right. Thus, the lowest point in each size distribution represents 400 mesh and each of the other sieve sizes must be shifted accordingly. A single regression line was calculated by combining the data for the six tests, excluding the coarsest feed and the two finest feed fractions. 6 This regression line, which is given by (Y \0.88 where y is the cumulative percentage of material

Jan 1, 1962

The Library of the above-named Societies is open from 9 A.M. to 10 P. M. except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The tine spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 10, 1917

By F. N. Flynn

- Introductory IN 1882, The Arizona Copper Co. Ltd., acquired producing copper mines at Metcalf and Morenci (locally called Longfellow). Metcalf is situated a distance of 7 miles, and Morenci a distance of 6 miles from the general office of the company at Clifton, Ariz. A reduction works with five blast furnaces was built in the center of the town of Clifton in 1884 and operated until January, 1914. Concentration of oxidized ores was begun in 1890-1891, in a mill built adjoining the smelter, and in October, 1893, a leaching process was started for treating tailings from the oxide mill. A sulphide concentrator with 300 tons capacity was built at Clifton and started treating chalcocite ores in July, 1896. This was the first mill to treat low-grade copper-sulphide ores successfully. Another concentration mill for sulphide ores was erected at Morenci in 1900. The, sulphide mills are now being remodeled to treat ores by concentration and flotation, with a capacity of 4,000 tons at Morenci and 500 tons at Clifton. The leaching plant has not been running since September, 1914. The average yearly production from this company's mines and reduction works from 1885 to date has been: Pounds 10 years ended 1894 6,864,902 10 years ended 1904 20,439,614 10 years ended 1914 : 32,665,905 Part of year 1915, to Sept. 12 30,206,106 4 months of 1916, to June 15,964,840 June, 1916...: ? 4,900,000 Construction on a new smelting plant was started in February, 1912, and finished in February, 1914. In the Transactions, vol. 49, E. Horton Jones published "Unit Construction Costs from the New Smelter of the Arizona Copper Co., Ltd:," which fully describes the construction of this plant, with details of costs.

Jan 9, 1916

By M. J. Pool, with Appendix by Larry Kaufman, R. W. Krenzer

Thermodynmic properties of the Cu-Mn system have been deterrrzined in the temperature range 973" to 1273°K by measuring the vapor pressure of manganese in equilibrium with alloys of compositions varying from 0.13 to 0.91 rnole fraction manganese using the Knudsen effusion technique. Activities of manganese calculated from the measured vapor pressures show large positive deviations. Calculated heats and entropies of mixing are positive with a maximum occurring at approximately 0. 7 mole fraction manganese. ThE investigation of thermodynamic properties of binary systems involving transition metals is of considerable interest at the present time. The incomplete subvalency electron levels of transition metals lead to unusual behavior in some alloys, and considerable information can be obtained by determining the thermodynamic characteristics of these systems and relating the thermodynamic behavior to observed physical properties. The Cu-Mn system, shown in Fig. 1,' provides an example of an alloy system in which the determination of the equilibrium phase diagram and various physical properties has received considerable attention, but very little work has been done on measurement of the thermodynamic properties. Elemental copper and manganese have comparable electronegatives, atomic sizes, and cohesive energies, but differ in crystal structure. They form a continuous series of solid solutions only at high temperatures and the structure varies in a continuous manner from fcc at the copper-rich end to fct at the manganese-rich end.' The purpose of this investigation was to measure the vapor pressure of manganese over a series of Cu-Mn alloys and from these values determine the thermodynamic properties of the binary system. Vapor pressure measurements were made in the temperature range 973" to 1273"K, remaining within the solid-solution region for each alloy studied. EXPERIMENTAL PROCEDURE The relative thermodynamic properties of solid Cu-Mn alloys were determined from vapor pressure measurements by means of the Knudsen effusion tech- nique. Several discussions of the theory can be found in the literature. In the case of copper and manganese, it is assumed that manganese is the only component subliming, so the vapor pressure of manganese over the various alloys can be determined directly by measuring the weight loss of the effusion cell. This is a valid assumption since the vapor pressure of manganese is about four orders of magnitude higher than the vapor pressure of copper in the temperature region of interest. The vapor pressure of manganese over the alloys at any given temperature is then related to the weight loss of the effusion cell per unit area per unit time. An upper limit of 1.5 x 10"s has been measured for the ratio of polyatomic to monoatomic molecules for manganese vapor in equilibrium with solid manganese at 1180°K, so it was assumed that manganese vapor is monoatomic. The effusion cells, fabricated from high-purity alumina, are 26 mm high, 18 mm OD, and have a wall thickness of 1 mm. Three different sized holes of 2.03, 2.54, and 3.18 mm diam were drilled in the lids from the inside face to minimize chipping, and the lids were then slip-cast onto the cells to provide a gas-tight seal. Alumina was selected for this particular application both because of its resistance to thermal shock and reaction with manganese vapor. In the ideal case, the orifice of the effusion cell should have a knife edge so that effusion through the orifice

Jan 1, 1970

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state's future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

By W. A. Ver Wiebe

Spurred on by the very high demands for new crude supplies resulting from World War 11, the oil men of Kansas strained every effort in 1943 to find as many new pools as possible. In all, 1761 test wells were drilled, ,of which 895 were successful in finding new oil supplies and 32 in finding new gas supplies. The total number of wildcat wells drilled in Kansas was 577, including the so-called "extension wildcats," which are located less than 2 miles from production. As a result of the very determined effort to find new oil reserves, 49 of the wildcat test wells found new oil pools in western Kansas and 7 found new oil pools in eastern Kansas. There were 289 rank wildcat tests, and among these 28 were successful ventures. They are responsible for 26 of the new oil pools recorded for the year and 2 of the new gas pools recorded. The ratio of dry holes to producing wells among such rank wildcats is thus approximately 10 to I (289 dry and 28 good). This compares with a ratio of II: I in 1942 and 6:1 in 1941; the same in 1940 and 5:Iin 1939. With nearly all wells flowing to their maximum economic capacity, the total production for Kansas during 1943 reached a new high; that is, 107,700,000 bbl., compared with 97,000,000 during the previous year. Similarly, the amount of gas sold during 1943 made a new high point on the production curve. The total amount was 122 billion cubic feet, compared with about 98 1/2 billion cubic feet for the year previous. As usual, the large Hugoton field of south- western Kansas accounted for approximately half of the total gas production. Highlights of the Year Despite the fact that 56 new pools were found in Kansas during 1943, it must be admitted that the future reserves of the state have not been increased greatly. Most of the new pools seem to be of minor value, although it is admittedly impossible to gauge the future production of any pool in Kansas with any exactitude. Judging by the later performance of some of the pools found in 1942 and in 1941, less than five of the new pools are likely to make any great contribution to the state's future oil reserves. Taking up the counties of Kansas in alphabetical order, the following statements summarize the highlights of the year. In Graham County, the Morel pool was extended to the southeast and this pool now promises to become one of the important pools of western Kansas. Several of the older wells have already contributed more than I000,000 bbl. of oil, and such a figure is considered very satisfactory in Kansas. In McPherson County, important new reserves were found by persistent drilling in township 17 S., R. I. W., the most northeastern township of the county. Many new wells in older pools and discovery wells in new pools make this region look promising. The Lindsborg pool, which had a sensational revival during 1942, was also extended in a number of directions and has now become a rather large producing area with a fairly high future potential capacity.

Jan 1, 1944

SAN FRANCISCO SECTION Roy H. ELLIOTT, Chairman - T. A. RICKARD, Vice-chairman W. H. SHOCKLEY, Secretary-Treasurer, 959 Waverley St., Palo Alto, Cal. D. A4. RIORDAN C. F. TOLMAN, JR. A joint meeting of the local sections of the several national engineering societies represented in San Francisco was held at the Engineers'. Club on Thursday evening, Sept. 26, 1918. The subject for the evening, "Fuel Conservation," was ably discussed by a-number of representatives of the Federal Administration and by engineers interested in the generation and utilization of all kinds of power on the Pacific Coast. The following extracts from papers presented at this meeting have been selected as being of the greatest interest and value to members of this Institute. Problems of the Fuel Administration ALBERT E. SCHWABACHER.-America's war needs call for 100,000,000 more tons of coal this year than in 1917, and 200,000,000 tons more than in 1914, when the war started, and this increase must come from a weaker man-power than that of 1917. It must be transported by a railroad system that has not been improved since the war started, and has been burdened with inconceivably greater demands than were made upon it before the war. This tremendous increased demand must be met by most intensive work in three directions; increased production, efficient conservation, and a distribution system which will insure against lost motion. While every European country has decreased its coal production since the war began, the United States has mined 50,000,000 tons more coal, during the first year of the war, and will increase this by another 50,000,000 the present year. Every 8 days there are being mined and transported as great a weight of coal as of the entire wheat crop of the United States. Of the 735,000,000 tons of coal which must be made available for consumption by our railroads, ships, war industries and people, 100,000,000 tons will come from the anthracite fields, the remainder from the bituminous fields. In 1917 there were produced about 330,000,000 bbl. of oil, and this year an additional amount over last year's production, of approximately 23,000,000 bbl. will be required. Water power developed 5,000,000 hp., the demand greatly exceeding the available supply.

Jan 12, 1918

By L. S. Richardson, N. J. Grant

REACTIONS of oxygen and nitrogen at low pressures with titanium have recently been studied by a number of investigators.1-3 Gulbransen and Andrew' noted that the reaction with nitrogen followed the parabolic rate law whereas the reaction with oxygen deviated slightly from this law in the temperature range 300° to 800°C. In the work reported here, commercial titanium (75 A) was used as the test material. Cylinders 2.5 in. long and 0.25 in. in diameter were machined from heavier bar stock. The test pieces were given a metallographic finish, immersed for 30 min in cold concentrated HC1, washed in water, then acetone, and dried with lint-free cloth. Reaction rates were determined in a modified Sieverts type apparatus by measuring the decrease in gas pressure of the reacting gas contained in a constant volume. The amount of gas added could be measured in a calibrated gas burette to an accuracy of 0.01 mm. During the course of a run the temperature never varied by more than 10°C and then only for brief moments. After placing the specimen in the furnace, the system was first evacuated for 12 hr at room temperature, and then flushed with purified argon five times, adsorbed gases being discharged during this period from the glass system with a high frequency spark coil. The flushing and discharging were repeated at 400°C. This rather involved procedure was found necessary after a number of trial runs indicated extraneous effects traceable to the system. Reaction periods up to 2 hr were used, at initial gas pressures of 0.2 to 0.5 atm. Experimental Results Fig. 1 shows the decrease in oxygen pressure for tests at 0.5 atm at various temperatures as a function of the square root of the time. Deviations from linearity are minor and the parabolic rate law is obeyed. Fig. 2 shows the same plot for the nitrogen reaction. A definite deviation from linearity is noted; however, it is probable that the higher initial rates are caused by the presence of small amounts of oxygen contamination, the initial faster rate changing to the slower rate after about 5 to 10 min. Calculations of the rate constants were made on the basis of the latter portion of the curves. The parabolic rate law constants calculated from these curves are shown for oxygen and nitrogen in Fig. 3. In spite of some scatter the average curves are quite definite. Changes in gas pressure of the order of 20 pct did not result in a measurable change in the rate law constants. The activation energy for the oxygen reaction was calculated to be 47,400 cal per mol (above 700°C), which is not in agreement with the value quoted by Gulbransen and Andrew' for lower temperatures, their value being 26,000 cal below 600°C. The activation energy for the nitrogen reaction was calculated to be 45,400 cal per mol above about

Jan 1, 1955

By J. C. Bradley

The relation of annealing temperature to conductivity of copper wire has been determined. Conductivity hard was 98.26 per cent. After a 10-min. heat,ing at 200" C. it was 98.69. By annealing 10 min. at 300" C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500" C. anneal; thereafter it decreased to 100.53 after a 950" C. anneal. If copper is gassed the decrease is much more than this. Material and Method The work was done on high grade electrolytic copper, 99.942 per cent, copper plus silver, silver 0.0008 per cent. It was hot-rolled to 1/4 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100" C. heating a coil was put into water, the water brought to . boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched. Results Data from the tests are shown in the table and plot (see Fig. 1); conductivity is referred to the International Annealed Copper Standard at 20" C. Conductivity hard is considerably less than conductivity soft.1 The increase is sharp when the wire anneals. The maximum, 101.15 per cent, in the particular material used, comes at 500º C.; thereafter the conductivity falls to 100.53 per cent. after 950" C. annealing, a drop of 0.62 per cent.

Jan 1, 1927

By C. Kremer Bain

DURING the past several years of diamond drilling in Washington County, Mo., the St. Joseph Lead Co. has discovered a concentration of commercial lead-zinc ore at four different points within an area of 36 square miles. The largest and to date the most promising group of these orebodies is located in the Indian Creek area. It was considered to be of sufficient value to warrant development. The Indian Creek area is in the center of the northern half of Washington County, 11 miles northwest of Potosi, Mo., the county seat. The location is readily accessible from Potosi by car or truck over the all-weather Missouri State Highway No. 114. The topography is one of rolling relief, varying from an elevation of 700 ft above sea level on Mineral Fork and Indian Creek to a maximum of 1176 ft at High Point Tower. It is divided in equal halves between the drainage to Mineral Fork and to Indian Creek. The shaft site at 1060 elevation is on the divide between the two drainage areas. The Indian Creek side is rough and heavily wooded, with only a few cultivated clearings. The slopes to Mineral Fork are more gentle and rounded, with much of the area cleared for farm land. Most of the surface is covered with Potosi and Eminence formations, which show little evidence of any structure. Ore structure was worked out by extensive diamond core drilling, with holes varying in depth from about 700 to 1300 ft. As of Oct. 1, 1950, 218 prospect holes had been drilled within the 36-square mile area. The ore is disseminated galena with considerable accompanying sphalerite in the Bonne Terre forma-tion in the shape of irregular blanket-type deposits. The main controlling structural feature of the outlined mineral zone is a buried pre-Cambrian rhy-olite-porphyry ridge extending partly through the Bonne Terre formation, which laps against the por phyry and also covers it. The mineralized zone parallels and forms an irregular halo around the porphyry ridge and is concentrated in the Bonne Terre formation where the La Motte sandstone is cut out by the porphyry ridge. This is a very common mineral occurrence in the southeastern Missouri lead belt district. The La Motte sandstone, which normally underlies the Bonne Terre formation, is thus cut out entirely. In this area the Bonne Terre is usually about 275 to 320 ft thick, the La Motte varying in thickness from zero up to 400 ft. Commercial concentrations of ore are indicated at several places, the most notable being at the shaft site where an orebody at least 4000 ft long with widths of 500 to 600 ft has been outlined. The total thickness of mineralized rock reaches 150 ft in some holes, although total ore thickness runs from 8 ft to about 60 ft, often in more than one layer. Preliminary Planning Ore reserves as outlined lend themselves to open-stope mining with trackless haulage and mobile loading machines and drilling equipment. This type of equipment has proved to be very efficient during recent years in the company's lead belt operations. After a study of bids for shaft sinking and an estimation of comparative costs, it was decided that the shaft would be sunk by St. Joseph Lead Co. personnel using company equipment. Since the plant site is about 26 miles from the company's nearest lead belt operations, it was necessary to plan a complete surface plant, including mill, shops, office, change room, and warehousing facilities. Immediately following the filing of an application for a certificate of necessity, a headframe was selected for which detailed drawings were already available. The order was placed for fabrication so that it could be delivered and erected in time to serve for sinking the shaft. This eliminated the expense of a temporary headframe. Drilling was started on two churn drill holes near shaft location, and two 1000-gpm deep well pumps

Jan 1, 1954

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By L. W. McKeehan

THE occurrence of twins in large ferrite crystals, made by a new process, was reported in a recent note. This paper describes a typical case of such twinning and suggests, on the basis of the observed facts, why smooth slip-planes are rarely observed in this metal. METHOD OF PREPARATION The material In which the crystals here dealt with were grown was made from 1/8 -in. Armco iron welding rod containing C, 0.04; S, 0.037; P, 0.003; Si, 0.008, and Mn, 0.02 per cent. This rod was cold drawn into wire about 1 mm. dia. A piece of this wire was supported vertically and was locally heated in hydrogen at atmospheric pressure to about 1400° C. by an alternating current (60 cycles per sec.) of about 35 amp., passed through it between a pair of travelling contacts about 8 cm. apart. The rate of travel for the case in hand was 12 cm. per hr. After some 30 cm. of the length of the wire had been heated and cooled in this manner the whole wire was immersed for a few seconds in dilute nitric acid, not restrained by alcohol. Etching was continued until, as nearly as could be judged by eye, the original smooth cylindrical surface of the wire was no longer capable of specular reflection.

Jan 1, 1927

By Lucius W. Mayer

The iron-mines of the Ilsede Hütte Co. are at a town called Peine, about 20 miles east of the city of Hanover, on the railroad to Brunswick (Braunschweig). Hanover, the capital of the province, is a military city, of approximately 250,000 inhabitants, and Brunswick, 33 miles to the westward, has half this number. The mines here described are located in a hamlet called Bülten. The Ilsede Hütte Co. operates two mines, 1.5 miles apart, in this district, Gruber Bülten Adenstadt and Gruber Lengede Bodenstadt. It also operates an iron-mine north of Hanover, known as Eiserhaven, and one in the Harz mountains, the Georg Friedrich, at Grauhof. At Bülten a coarse conglomerate, a, Figs. 1 and 2, contains nodules of limonite, cemented together by calcium phosphate. The ore contains Fe, 25 to 45; Mn, 3 to 4; P, 0.6 to 1.4; S, 0.02 to 0.09; and CaCO3, 40 per cent. Directly above the conglomerate is limestone, b, followed by a mixture of clay and sand, c. Below the conglomerate is a hard clay floor, d. The ore-body, from 10 to, 12 km. long, and from 3 to 4 km. wide, has a maximum thickness of 20 m. It clips approximately 10° S.E., and strikes N. 45° E. Diamond-drill prospecting shows that the thickness diminishes to 1 m. as the end of the deposit is approached to the northward. At this point the deposit is 250 m. below the surface. In Fig. 2, the arrow, A, indicates the general direction of the work along the face, a, which is carried forward in a straight line for its entire length. At B, a train is approaching, which has come from the bench-track, shown at G, by a circuitous route, and is dumping the overburden behind the face, in the space left by the excavated rock. Formerly the work at this mine was essentially open-cut, the deposit having a very strong outcrop. Figs. 1 and 2 show also

Sep 1, 1908

By Frank B. McKune

This is something new in my life. A lot of you men here today I do not know, and some I do know. So if you have any remarks to make, I wish you would give your name and the name of your company. This is the first Acid Meeting which has been held under the auspices of the National Open-Hearth Steel Conference, and I hope it is a success. Whether it is a success or not depends entirely upon the support we get. If it does get good support, I have the idea it will be continued as a regular feature of the National Open-Hearth Steel Conference. We all think we have pretty good practices. But we can all learn and I hope that you, gentlemen, who take issue with the things someone else has said will stand up and give your opinions. Otherwise, the meeting will fall rather flat, and we won't get a great deal out of it; and there will not be enough interest shown by the National Committee to continue to place the meeting on the regular yearly program.

Jan 1, 1940

By Roy P. Full, Robert M. Grantham

Regional structural adjustments in early Tertiary time resulted in the development of the Republic graben, a major down-dropped block that is from 6 to 10 miles in width and more than fifty miles in length. The graben became the center of extensive volcanic activity during Eocene and Oligocene time, resulting in a thick sequence of water-laid tuffaceous sediments, volcanic flows, and associated intrusives. A younger series of sediments, pyroclastics, and flows were deposited in structural depressions within the graben following the period of widespread volcanic activity. The Republic mining district is located along one of the major intragraben structural zones, where continuing subsidence during the period of volcanic activity resulted in an increased thickness of flows and associated flow breccias and pyroclastics. Intrusive masses in part healed early graben-forming faults, but later subsidence reopened old faults and created new fracture zones which later became the control for the gold-quartz veins. Considerable block adjustment along the subsidence area is evidenced by the structural pattern in the mines, and telescoped vein structures indicate north-south compressional stresses and east-west graben-forming tensional stresses prior to and during the emplacement of the veins. The veins, varying from a few feet to more than 50 feet in width, are filled primarily by fine-grained quartz, commonly chalcedonic or porcelain-like in appearance. Finely laminated dark-gray to black concentric banding within the veins generally distinguishes the better-grade ore zones, which contain finely disseminated sulfides and ore minerals that include principally electrum, stephanite, naumannite, and native silver.

Jan 1, 1968

By W. J. Parton

THE efficient recovery and preparation of small sizes of anthracite called No. 4 Buckwheat (3/3 2 by 1/3 2 in.) and No. 5 Buckwheat (1/3 2 in. by 0), present a difficult problem to the anthracite operators. In many instances preparation of these sizes, particularly No. 5 anthracite, is extremely inefficient. In many of the older preparation plants, inadequate facilities, and often none at all, were provided as an integral part of the plant for cleaning this fine anthracite. Consequently, much of the material smaller than s, 32 in. was discarded. As the demand for these sizes increased, facilities for preparing the fine sizes were often crowded into existing structures with consequent sacrifices of capacities and efficiency. In addition to this condition, the methods of preparing the finest sizes are being developed in an attempt to improve their efficiencies. Because the demand for small sizes of anthracite still is increasing, many operators would benefit by investigating and improving the cleaning equipment employed on these sizes.

Jan 1, 1949

By R. Priestner, R. F. Krause

Solid, cylindrical crystals of a iron have been fractured at 10°K by the simultaneous application of tension and torsion stresses. Thus, a complex distribution of normal (sN) and shear (ss) stresses existed in a cleavage plane at fracture. In every crystal the clearage-plane normal was inclined to the specimen axis, so that a unique point, M*, in the operative cleavage plane was defined where the quantities sn and s2 N + s2 S) were maximized. It is shown that the maxirrzum resolved normal stress on the cleavage plane at fracture decreased as the resolved shear stress in the cleavage plane at M* increased. Thus, a normal stress la?*! for fracture was not satisfied. A fracture law which takes shear stress into account. and which predicts that (s2 N +s2S) should be constant, is to be preferred. However, the data is best represented by a linear dependence of sN on sS, sS which 110 physical significance can be attached. It is suggested that the fracture-nucleating -mechanism is a short-range one. A critical stress law has not yet been unequivocally established for the propagation of cracks in metals. Measurements of the tensile fracture stresses of variously oriented zinc single crystals1 failed to establish the normal stress law expressed by In Eq. [1], sN is the fracture stress, P, resolved normal to the fracture plane, and 0 is the angle between the fracture -plane normal and the stress axis. Similarly, a comprehensive investigation failed to verify the normal stress law for the tensile fracture of a-iron single crystals.' However, a subsequent investigation,3 using iron from the same ingot, presented fracture data which obeyed the normal stress law. It has been shown previously4,5 that the Griffith criterion for fracture6 does not predict such a normal stress law. This result is of particular significance in considering the fracture of metals, such as zinc and iron, which may fail by cleavage. In these metals fracture propagates in a well-defined "cleavage" plane, whether or not an applied stress is normal to it. When the cleavage-plane normal deviates from the direction of application of a uniaxial stress, for example, the crack propagates under the combined action of normal (sN) and shear (ss) stresses. When the presence of a resolved shear stress in the crack plane is taken into account, the Griffith criterion is expressed by4

Jan 1, 1967

By Daniel N. Beshers, Ralph H. Condit

An expression for the diffusion coefficient of inlerstitial atoms in the bcc lattice is derived which takes account of jumps between tetrahedral and octahedral interstices. The results are applied to the case of carbon diffusion in iron to find values for jump frequencies of the types, octahedral-tetrahedral, tetra-hedral-tetrahedral, and tetrahedral-octahedral. ThERE has been renewed discussion1-5 concerning the mechanism of diffusion of interstitial atoms in the bcc lattice. This lattice has both octahedral and tetrahedral interstices, and it has been pointed out that the interstitial atoms may make jumps of the octahedral-octahedral type, hereafter called o-o, octahedral-tetrahedral, o-t, and tetrahedral-tetrahedral, t-t. Doubt has been cast on the applicability of snoek's8 model for internal friction to some interstitial migrations in bcc lattices wherein he proposed 0-0 jumps as the principal mechanism of migration. Also, the anomalous excess diffusion of carbon in iron at high temperatures4 has been ascribed to t-t jumps,2,3 even though the sites normally occupied are octahedral. In this paper an expression is derived for the diffusion coefficient, taking account of the three types of jump mentioned. The relationship of the coefficient to the corresponding internal friction relaxation time is found for the limiting case corresponding to Snoek's model. These results are applied to the case of carbon in iron. In Fig. 1, the structure is shown with the locations of the interstices. Each o site has four t site neighbors coplanar with it, and each t site lies halfway between two o sites. There are four t site first neighbors of a t site lying at the vertices of a tetrahedron. Let the average fraction of atoms occupying o sites and t sites be No and Nt, respectively. Since there are six o and twelve t interstices per unit cell having a lattice parameter, a, the concentration of interstitial atoms will It will be assumed that three types of jumps may be distinguished, t — t, t — o, o — t,for which the jump

Jan 1, 1968

1. Healthy and active Local Section organizations, are vital factors in promoting the vigor and growth of the Institute. 2. Activity on the part of Local Sections should be recognized and stimulated by appropriation of funds from the Institute's treasury; and these appropriations should be as large as is consistent with the relative needs for other activities. 3. As between different Sections, the amount of such appropriations should.

Jan 1, 1939