Search Documents

By C. S. Barrett, D. F. Clifton

THE transformation that occurs in lithium and its solid solutions containing magnesium1,2 is similar in many respects to other diffusionless transformations of the martensitic type. This general similarity makes it desirable to investigate the transformation curves in detail. The current interest in the phenomenon of stabilization in martensitic transformations has created a need for a careful appraisal of possible stabilization effects in both cooling and heating transformations in lithium alloys. The effect of prior heat treatment on the temperature at which transformation begins and the effect of various temperature cycles in partially transformed alloys also merit attention. Limited data on some of these features were presented previously,' but the present studies have been made with improved apparatus, in which erratic fluctuations were smaller than in the earlier work, and include many independent determinations of certain critical observations. Material and Methods Geiger counter X-ray spectrometers were used: a Norelco instrument, original model, and a General Electric XRD-3. The low-temperature specimen holder has been described elsewhere." Specimens 10 mm in diam and 1.5 mm thick were held in firm contact with a copper block which was attached to the lower end of a stainless steel tube that extended up to a reservoir of liquid nitrogen. A heating coil on the tube permitted a controlled temperature gradient along the tube, so that desired temperatures and rates of heating and cooling could be obtained by controlling the heating current. The specimen was surrounded by an atmosphere of evaporated nitrogen in an insulated chamber having double cellophane windows. The temperature of the specimen was read by a thermocouple imbedded in it close to the irradiated area; the specimen could be held at constant temperature within 1°C for long periods. The body-centered cubic 200 reflection near 8 = 26" was used as the index of the amount of b.c.c. material present; occasional checks were made using the most suitable line of the low-temperature phase, the close-packed hexagonal 110 line near 8 = 29". Copper radiation was used throughout. A continuous record was made of the reflected intensities on a strip chart recorder, both when the peak intensity of a line was being followed and when the lines were being scanned at constant temperature. On the continuous recordings of peak intensity, periodic checks were made on the background intensity between the lines, and on the setting of the spectrometer for maximum intensity. The lithium-base solid solution containing 12.4 atomic pct Mg (33.3 wt pct) that had been used previously' was chosen, as it had a transformation range at relatively high temperatures, so as to permit wide temperature cycling within the range. Just prior to use a pellet was cut from the ingot,

Jan 1, 1951

By GEORGE O. SUMAN

IN THE operation of oil properties there are various difficulties with pumping wells which can often be overcome or greatly lessened if sufficient attention is, directed towards pump and tubing problems. The difficulties referred to are the wearing out of pumps, sanding up of pumps, and the sanding up of the hole. As the perforations in the oil strings are large and the oil and sand loose and unconsolidated considerable trouble is often encountered in pumping wells due to the ease with which' the sand can come into the holes. DETERMINING FLUID LEVEL In determining the proper depth at which to tube a well it is essential to first find out something about the behavior of the fluid in 'the hole: Facts in regard to this natter can be obtained by finding the fluid level on pulling the tubing, by making a pumping test on the well tubed to various depths, and by bailing tests during cleaning out work. In ordinary oil field operations it is customary to take the fluid level at the time of pulling the tubing. This 'can only be done when the pump is not sanded up. There are two methods used in obtaining the fluid level. One method is to note where the outside of the tubing starts, to be covered with fluid when pulling the

Jan 1, 1925

[ARTICLE I. NAME AND OBJECT Section 1. This Society shall be known as the Society of Petroleum Engineers of the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. Section 2. The object of the Society of Petroleum Engineers shall be to furnish a medium of cooperation among those interested in the petroleum-natural gas industry an to promote the advancement of this branch of mineral technology through meetings to stimulate the preparation, reading, discussion and circulation of papers connected therewith. ARTICLE II. MEMBERS Section 1. Any person who is a member of AIME may become a member of this Society by the specified process. Section 2. Local organizations may be formed by the Society of Petroleum Engineers as subsidiary units, the membership of which shall be subject to and in accordance with the by-laws of the Institute.]

Jan 1, 1961

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

department, first as a practical miner, next. as rodman on the survey corps, of which he soon became chief, then draftsman and mining engineer in the company's office. In January, 1916, he was promoted to the position of district engineer in charge of mining engineering work. He became a member of this Institute in September, 1917. Captain Ba.llamy's military experience began at the same time as his engineering practice. He was a charter member of Company A, Engineers, N. G. P., which was organized ten years ago. He saw service on the Mexican border as First Lieutenant of this Company, and remained in that position until November, 1916. In July, 1917, he was again called into service and was sent to Camp Hancock, Ga., with the 103d Regiment of Engineers. Before joining this regiment he attended a school for officers at Fort Sill, Okla., where he received special training in field fortifications. In December, 1917, he was commissioned Topographical Captain on the Regimental Staff, and in April, 1918, preceded his regiment by about six weeks to France, where he again attended an officers' training school. He rejoined his regiment on July 15, near Chateau Thierry and was killed near Fismes on Aug. 9, 1918. Lieutenant Martin F. Bowles Martin F. BOWleS, born Apr. 25, 1893, at Bonne Terre, Mo., and graduated from the Neodesha, Kans., High School, had finished all but one month of a four-year course in metallurgical engineering at the Missouri School of Mines, Rolla, Mo., when on May 12, 1917, he entered the first Officers' Training Camp at Fort Riley, Kans. At the close of the training period, he was commissioned a Sccond Lieutenant and assigned to Co. B, 355th Infantry, 89th Division, and stationed at Camp Funston. He left this camp with his company on May 21, 1918, and sailed from an eastern port on June 4, ayriving in England on June 15, 1918. After a short stay at a rest camp there, he proceeded to France. On August 14, he wrote that he was with Battalion Headquarters as Gout Officer, 1st Battalion, 355th Infantry, 89th Division. The last letter received from him, dated September 2, was written in his dugout and contained the following: "Here it is 2.45 a. M. Sitting in a dugout waiting for some patrols to report back in, I am writing this by the light of two candles." He was killed in action on the night of Sept. 3, 1918. The letter of notifi-

Jan 1, 1920

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By E. C. Truesdale, Gerald Edmunds

A few years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.&apos; During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. Table 1.—Typical Analyses Percentnge by Weight Sum of Zinc Fe, Ib1 Fe Cd 1A1 cd Special High Grade*.......... 0.007b 0.005b 0.005b none O.OIOb C.P. (chemically pure)......... < 0.0002 0.0005c 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 637). b Maximum. &apos; Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By W. C. Ellis, E. S. Greiner, M. E. Fine

C. H. Samans and W. R. Ham (Chicago, Ill., and Dix-field, Maine, respectively)-—For several years we have been studying transitions of this basic type in metals, alloys, glasses, etc. Usually, however, they are not so clearly marked as those which the authors have found, and hence are much more difficult to determine accurately. Since our studies indicate that most of them occur virtually unchanged (as far as temperature is concerned) regardless of the form in which the element appears, we believe that they are a characteristic of the atom. Specifically, we believe that there is an additional rotational degree of freedom possessed by the nucleus which has not been considered heretofore. This nuclear rotation is made up of several components, each related to the several quantum shells of electrons. In chromium there are four of these shells and hence four separate series of characteristic transition temperatures. The lowest temperature at which any transition occurs, based on the present state of our computations, is 125°K, 4° higher than the authors&apos; value of 121°K. A convergence of this series, we believe, shows up at the higher temperature of 2085 °K, surprisingly close to the transformation temperature of 2103°K recently announced by N. J. Grant of M.I.T. for a body-centered to face-centered transformation in chromium. Likewise, our computations indicate a temperature of 311°K for the second transition temperature, reported by the authors as 310 °K. A convergence of this series, we believe, shows up at a higher temperature as the melting point at 2163°K. Although our work on these series must, in a sense, still be regarded as empirical, since we do not understand fully as yet just what the series mean, it is based on a reasonably firm picture. The individual constants, from which the various series are computed for each element, comes directly from the X-ray K absorption limit. Furthermore, the same basic method has accounted for transformation and melting temperatures in about 50 of the chemical elements, which is all we have tried thus far. In many cases the only known transformation is the melting point, but in others the occurrence of transformations or other transitions, equally as well marked as those of the authors, has been pointed out by others. These observations have assisted us greatly. Consequently we were very pleased to see the authors&apos; excellent work in finding these two transitions in chromium. With these confirming data, our picture of this element is clarified considerably, so we expect that at least some of our work can be published in the near future. R. C. Ruder (E. I. du Pont de Nemours & Cu., Wilmington, Del.)—The authors&apos; interpretation of these transitions in terms of 3d to 4s electronic structure transitions is most interesting. It would be interesting to have additional experimental evidence of such transitions from the temperature dependence of the Hall coefficient in the neighborhood of the property changes discussed in this paper. Simple theory15 suggests the Hall coefficient as a measure of the free electron (or s electron) concentration per unit volume. It has been shown that for paramagnetic&apos;" and ferromagnetic1? metals the simple theory is in fact too simple. However, the existence of a discontinuity in the Hall coefficient would provide information which should aid both in our understanding of these transitions and the significance of the Hall coefficient in these metals. It was rather surprising that no significant paramagnetic effects were observed. In this connection the recent work of McGuire and Kriessman18 is cited. They measured the magnetic susceptibility of chromium from 20" to 1460 °C. They also observed no large change in the susceptibility although there might be a change in slope in the vicinity of the 40 °C transition. The existence of these 3d to 4s electronic transitions has been discussed in connection with the paramagnetic susceptibility behavior of nickel and nickel alloys.&apos;"-" Assuming a correspondence principle between classical and quantum mechanical paramagnetic theory and using classical theory to calculate the effective Bohr magneton number from the Curie constant for substances obeying the Curie-Weiss law," it is found that the effective magneton number is a function of temperature. The process of calculation involves the inverse of the differential of the 1/x4 vs. temperature curve so that good and numerous data are necessary to obtain significant results. The data of Fallot23 show a discontinuous increase of about 12 pct in the effective magneton number between 850" and 900 oC, followed by a continuous increase up to the melting point. The data of Sucksmith and Pearce24 show a possible 8 pct increase. The older data of Terry25 and Weiss and Foex26 show a continuous increase. It is possible that small amounts of impurity atoms change these electronic transitions significantly. Fallot&apos;s23 data on a nickel alloy with 4.5 atomic pct Fe indicate that the discontinuity occurs around 1300 °C. Systematic investigation of the transition metals for transitions of this nature should provide information which would be very valuable for our understanding of these metals. The absence of antiferromagnetic structures in chromium has been shown by Shull27 using neutron diffraction techniques. M. E. Fine, E. S. Greiner, and W. C. Ellis (authors&apos; reply)—The remarks by Drs. Samans and Ham are certainly very interesting, in particular those pertaining to the close agreement between the theoretically calculated values for transition temperatures in chromium and the experimental values reported by a number of investigators. This is a remarkable achievement and we shall look forward to a more detailed presentation of the method followed in their calculations. We do not believe that the transition in pure chromium near 40 °C remains temperature invariant with alloying, as was reported by Samans and Ham for a number of the substances that they studied. We have not done any work with alloys but base our belief on the results of earlier studies in which less pure chromium was included and considerably lower transition temperatures were observed. The transition tempera-

Jan 1, 1952

By Haydn H. Murray, Sam H. Patterson

The term "clay" is somewhat ambiguous un¬less specifically defined, because it is used in three ways: (1) as a diverse group of fine-¬grained minerals, (2) as a rock term, and (3) as a particle-size term. Actually, most persons using the term "clay" realize that it has several meanings, and in most instances they define it. As a rock term, clay is difficult to define be¬cause of the wide variety of materials that com¬pose it; therefore, the definition must be gen¬eral. Clay is a natural earthy, fine-grained ma¬terial composed largely of a group of crystalline minerals known as the clay minerals. These minerals are hydrous silicates composed mainly of silica, alumina, and water. Several of these minerals also contain appreciable quantities of iron, alkalies, and alkaline earths. Many defini¬tions state that a clay is plastic when wet. Most clay materials do have this property, but some clays are not plastic; for example, halloysite and flint clay. As a particle-size term, clay is used for the category that includes the smallest particles. The maximum-size particles in the clay-size grade are defined differently on various grade scales, Soil investigators and mineralogists gen¬erally use 2 micrometers as the maximum size, whereas the widely used scale by Wentworth (1922) defines clay as material finer than ap¬proximately 4 micrometers. Some authorities find it convenient to use the term "clay" for any fine-grained, natural, earthy, argillaceous material (Grim, 1968). When used this way, the term includes clay, shale, or ar¬gillite, and some argillaceous soils. Even though no standard definition of the term clay is accepted by geologists, agronomists, engineers, and others, the term is generally un¬derstood by those who use it. Clay is an abun¬dant natural raw material, and it has an amaz¬ing variety of uses and properties which will be discussed in this chapter. Clays rank among the leading industrial min¬erals in both tonnages produced and total value. Their importance is indicated in Table 1, which lists the 1970, 1971, and 1972 production and values according to the U.S. Bureau of Mines (Ampian, 1972). Adequate reliable statistical data on which to summarize world production of clay are un¬available; this paragraph outlines the world re¬quirements for clay only in a very general way. According to one estimate, the world bentonite production in 1972 was 3.5 million tons (Anon., 1973a), but in the authors&apos; opinion it was prob¬ably at least 5 million tons. The total fuller&apos;s earth produced was at least 1.5 million tons and may have been as much as 2 million tons. The total world kaolin production in 1972 was more than 10 million tons. Approximately 7 million tons of this total was produced in only two regions-the Georgia-South Carolina kaolin belt in the United States and the Cornwall re¬gion, United Kingdom. The world&apos;s 1972 out¬put of ball clay, which is also produced pri¬marily in the United States and the United Kingdom, was approximately 1.5 million tons or perhaps a little more. The total world fire clay production in 1972 was probably about one and one-half to two times and the miscellaneous clay production three times the United States production. As industrial minerals, clays are a complex group that consists of several mineral commodi¬ties, each having somewhat different mineral¬ogy, geologic occurrence, technology, and uses. In this chapter these commodities are organized

Jan 1, 1975

By George H. Deike

DURING the past year a survey was conducted by the Committee on the Promotion of Student Interest in Coal Mining to determine whether the program as laid down in past years was operating effectively. It is a source of satisfaction and pleasure to be able to report considerable headway among operating companies in putting cooperative scholarship plans into operation. In previous committee reports the pioneer work along this line by Eugene McAuliffe, president of the Union Pacific Coal Co., has been cited. That Company now has in its employ, in responsible positions, three men who received their education under such scholarship plans. One student under a similar plan is now studying at the Colorado School of Mines.

Jan 1, 1942

By A. B. Kinzel

SILICON and its metallurgical uses have been the subject of speculation since the earliest days of modern civilization. The early philosophers, Theophrastus and Pliny, believed that silica was a special form of ice, an opinion that was not seriously challenged until the seventeenth century. The first comprehensive view of the nature of silica was advanced by Lavoisier in 1787. He assumed silica to be an oxide of an unknown metal. In 1808 Berzelius produced ferrosilicon by heating silica, iron and charcoal. Probably the first produc¬tion of crystallized silicon was in 1854 when H. St. C. Deville accidentally produced the material while electrolyzing a double chloride of aluminum and sodium containing siliceous impurities. It is not strange that the early investigators should have given so much attention to silica and silicon, because of the great natural abundance of the former. Although silicon does not exist in the elemental state in nature, it has been estimated that the lithosphere contains approximately 60 per cent silica; quartz and rock crystal are found in practically every part of the world.

Jan 1, 1933

By S. M. Marshall, B. M. Bird

For a number of years European investigators have used laboratory methods of predicting the probable strength of coke made from coal, and recently several investigators in the United States have reported the use of various tests for this purpose. There is at present no method accepted as standard, however, nor is there even agreement as to the general type of test that should be used. Furthermore, because the details of most of the tests have not been worked out carefully, one investigator can not hope to duplicate the work of another. The extension of coke manufacture to new localities in the United States, and the increasing need for cokes of exceptional qualities made from the most economical mixtures, made it desirable to have some simple laboratory test which will determine whether given coals, alone or blended with other coals, are more satisfactory from the standpoint of coke strenpth- than others of different cost. The work described herein has resulted in the development of a simple laboratory test which, it is believed, can be generally adopted in coal laborat,ories, and which will give concordant results even though performed by different investigators in different laboratories. The general method of predicting whether a coal or a mixture of coals will produce a strong coke, resistant to crushing and shattering, has been to correlate the known strengths of the cokes produced in commercial ovens with some measurable constituent or with some property of the coals, and then to use the relationship so found for forming an estimate of the coking strengths of coals unknown. Several such correlations have utilized the percentages of the various ultimate constituents of coal, such as the oxygen content and the hydrogen-oxygen ratio;(39)§ other correlations have involved the proportion of a, B and r com-pounds, (17,21,30c) or of "oil and solid bitumens."(16,30) Also a relationship has been traced between the coking properties of coal and the rate of change of the resistance offered to the flow of an inert gas by fine particles of the coal while being slowly heated. (11,176) But the most general corre-

Jan 1, 1930

By E. P. Pfleider, W. G. Pariseau

This paper reports the theoretical and experimental results of an analysis of ore pass drawdown as a problem in soil plasticity. The method of analysis developed appears to be a promising technique of investigating the mechanics of fragmented materials. A reconstructed plasticity theory brings experiment and theory into reasonable agreement, and hence may provide the foundation needed for rational ore pass design. The gravity-induced movement of broken rock through ore passes is an economical method of transporting fragmented materials through large vertical distances in underground mines, provided the ore pass is well designed. Unfortunately, the design procedures now followed do not very often result in ore passes that function properly. On the one hand, the huge accumulation of empirical data pertaining to the movement of materials in gravel bunkers, storage bins, deep grain silos and other structures that have features in common with ore passes remains uncorrelated. On the other hand, there is a dearth of experimental data substantiating theoretical models of material behavior. Consequently, reliable generalizations encompassing the broad spectrum of problems involved have not been forthcoming. AS an initial step towards improving the situation, a detailed case study of two-dimensional ore pass drawdown was made. The mechanics of the process were analyzed theoretically as a problem in soil plasticity and tested experimentally through observations of a laboratory ore pass model. THEORY Taylor1 defines a soil as a "mass commonly considered to consist of a network or skeleton of solid particles, enclosing voids of varying size." Broken rock in an ore pass is such a material. In plasticity theory this material is replaced by an idealized substance that deforms elastically up to some state of stress at which slip or yield occurs,2 For com-pressive states of stress, the Mohr-Coulomb criterion is a satisfactory yield condition. After the yield point is reached, the ideal soil deforms in accordance with the concept of plastic potential.4 Under plane strain conditions the governing equations separate into a system of stress equations and a system of velocity equations.&apos; Only stress variables appear in the stress system. The velocity system, however, contains a stress variable. The two systems are, therefore, coupled. Both systems are hyperbolic, and each has two real, distinct families of characteristic curves that coincide according to the classical theory of ideal soil plasticity. The

Jan 1, 1969

By F. R. Brotzen, D. L. Davidson

ALTHOUGH much effort has been devoted to the problem, the nature of plastic flow in bcc metals is still not fully understood. Some of the difficulties encountered stem from the scarcity of information on orientation effects and the uncertainty as to the glide system in these metals. In an attempt to provide some of this information, the present investigation was carried out, using zone-refined molybdenum single crystals deformed in tension and in direct shear. Considerable evidence exists to indicate that the primary slip system for molybdenum is (110) <111>.1,2 Figs. 1 and 2 indicate that this is, indeed, the case for direct shear at room temperature (see Ref. 3 for a description of the shear-testing equipment and procedure). Moreover, from Fig. 2, the shear stress on the (123) is lower than that on the (112). This would be the case if, as has been suggested,4,5 slip on these two planes is in reality com-

Jan 1, 1965

By J. C. Fisher, J. H. Hollomon

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in &apos;hap&apos; an&apos; size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0&apos; the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate&apos; by Griffith4 &apos;0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By J. H. Hollomon, J. C. Fisher

The fundamental problem concerning the fracture of both crystalline and noncrystalline solids is the divergence between the actua1 and the theorcticallY computed fracture stresses; the stress required for fracture, computed from the forces between atoms, is many times that actually observed with commcrcinlly available materials. Computatiolls have been made,,2 indicating that the theoretical fracture stress should be from 100 to 1000 times that actually observed. There are other incidental problems that have arisen, perhaps the most importallt of which is the problem of size effect often observed in the measurement of the fracture stress of non-metallic solids, such as glass. Another effect conccrns the relation between deformation and the stress required for fracture, Experiments recently made with pearlitic steels indicate that the tensile fracture stress increases with increasing tensile deformation and decreases with increasing prior com-pressive deformation, This marked ani-sotropy of the effect of deformation on the fracture stress is in contrast with the essential isotropy of the flow stress. Early experiments on rock salt crystals by Joffe, et al.3 have illustrated the effect of tensile strain in increasing the tensile stress required for fracture. A consistent theory must be constructed that will explain not only the divergence, of the measured fracture stress from the theoretical value, the size effect, and the ergence of deformation; but will also explain and predict the effects of combined stress, of temperature, of strain rate, and of metallurgical structure. With respect to this last variable, it has now been relatively well established that the carbide particle is the clement of structure controlling the fracture of steels. In steels carbide particles vary in shape from plates to spheroids. It has been found that not only docs the magnitude Of the Fracture stress depend upon the size and shape of these particles. but also its dcpendencc upon strain is affected by changes in &apos;hap&apos; an&apos; size Or the particles. The precipitate resulting from the age hardening Of duralumin also modifies the fracture stress of this alloy. Nonmetallic inclusions greatly lower the fracture stress of all metals. The magnitude of the lowering depends 0&apos; the size and shape of the included particles. In glass, the major source of the low fracture stress has been fairly conclusively demonstrate&apos; by Griffith4 &apos;0 arise from real flaws or cracks present in the material. He showed that the stress concentration at the end of a defect was of suficient magnitude to raise the stress at this location to a value comparable with the theoretical strength Of the material. If the cracks were reduced in size, Griffith showed that the observed fracture slrength the by virtue Of the decrease in stress concentration. He also pointed out that cracks disposed perpendicularly to the applied tensile stress would be more effective in lowering the fracture

Jan 1, 1947

By Laurence Delisle, Arron Finger

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Arron Finger, Laurence Delisle

The alloys formed by the addition of nickel to iron by conventional metallurgical procedures show physical properties that differ widely from those of the individual metals. The effect of alloying on the mechanical properties is most pronounced in alloys containing between 15 and 25 per cent nickel. The tensile strength of an alloy containing, for example, 20 per cent nickel and 80 per cent iron (with 0.06 per cent carbon), in an annealed condition, is above 150,000 lb. per sq. in.$ owing to a martensitic type of transformation, as compared with about 50,000 lb. per sq. in. for pure iron in the same condition. The object of this work was to determine whether the same beneficial alloying effect coulcl be obtained in alloys of iron and nickel prepared by powder metallurgy technique. Procedure Bars and pellets for tension and compression tests, respectively, were made. Two groups of specimens were prepared: (I) by cold-pressing the powders and sintering; (2) by cold-pressing the powders, sintering, repressing and resintering. Raw Materials Nickel powder supplied by Metals Disintegrating Co., marked MD-151, was used. A typical analysis of this powder was as follows: sulphur, 0.040 per cent; copper, 0.18; iron, 0.23; manganese, 0.002; magnesium, o.oo15; lead, 0.035; tin> 0.025; silicon, 0.08; chromium, 0.008. Electrolytic iron powder supplied by Plastic Metals Inc. was used. A repre-sentative chemical analysis for impurities other than gases, supplied by the vendor, gave the following results: carbon, 0.005 per cent; manganese, 0.002; silicon, 0.003; phosphorus, 0.001; sulphur, 0.004; nickel, 0.008. The fractions from these powders passing a 325-mesh sieve were reduced in hydrogen at 600°C. for one hour, to clean the sur-faces of the particles. The reduced pow-ders, slightly caked, were ground in a mortar and screened again through a 325-mesh sieve. Mixing The proper proportions of the powders were mixed overnight on rolls, in glass jars fitted with iron-wire baffles to break aggregates of particles that might form. Pressing All specimens were compacted on hy-draulic presses. The pellets were com-pacted in a cylindrical die, 34-in. diameter. The ratio of thickness to the diameter of the pellets was maintained as nearly as possible at 0.9, as specified for standard short compression pieces. The tensile bars were made by compacting 30 grams of powder. Their shape is shown in Fig. I. The compacting pressures for the pellets and the tensile bars were:

Jan 1, 1946

By Ralph Sweetser

THE Round Table. on Qualities of Pig Iron, under the auspices of the Joint Committee on Qualities of Pig Iron, which is made up of members of the American Institute of Mining and Metallurgical Engineers, the American Foundrymen&apos;s Association, the American Society for Testing Materials, the Gray Iron Institute, and the. Malleable Iron Institute, was held at the Palmer House, Chicago, Ill., on Oct. 1, 1935. PROCEEDINGS R. H. SWEETSER,* New York, N. Y.-Seven years ago last June we had a round table on qualities of pig iron1, and at that time the foundrymen were out with their battle-axes for the blast-furnace men, and the open-hearth men were doing the same thing. After that meeting there was really a determined effort to find out about the qualities of pig iron, and great progress has been made all along the line. This afternoon we want to have a frank discussion of the qualities of pig iron, whether it is the molten pig iron going into the steel plant, or cold pigs going to the different foundries. We ought to hear something from Dr. J. T. MacKenzie, who is chairman of the Joint Committee, and from Mr. R. E. Kennedy, the tech-nical secretary. J. T. MACKENZIE, t Birmingham, Ala.-As a result of that meeting in Chicago, there was considerable agitation in the Foundrymen&apos;s Association to develop a set of tests for pig iron. One of the difficulties was that nobody talked the same language on shrinkage, draws, live iron, dead iron, and so forth, which were the main com-plaints against pig iron. By request of a committee of the Foundrymen&apos;s Association, the Bureau of Standards ran a comprehensive set of tests that did develop the prin-ciples governing the optical pyrometer as applied to cast iron and pig iron. Then the Bureau went on further with the fluidity test, and developed a method for the absolute changes of volume at the freezing point.

Jan 1, 1936

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite &apos;is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. &apos; As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924