Search Documents

By Oscar E. Harder, H. A. Grove

It is now just a quarter of a century since Fred W. Taylor§(23) pub-lished his classical paper On the Art of Cutting Metals, describing his researches in which he, in cooperation with Maunsel White, had developed what is essentially the modern method of heat-treatring high-speed steels. Regarding this research, Dr. Sauveur,(22) in his address on Steel Wizards, Past and Present, at the annual banquet of the American Society for Steel Treating in Philadelphia in 1920 said, "The discovery of high-speed steel, or if you prefer, of the treatment imparting high-speed properties to certain steels by Taylor and Maunsel White I am inclined to consider as our one epoch-making contribution to the metallurgy of steel." It was at about that same time (1900) that Taylor exhibited high-speed steels, heat-treated by the improved process, at the World's Exposition in Paris and attracted much attention by showing that the steels would operate at such feeds and speeds that the tips of the tools were visibly red hot. This observation must have started metallurgists to wondering regarding the relative hardness of the various steels at red-heat temperatures. Considerable work has indeed been done in an effort to measure the hardness of high-speed steels and related materials in the red-heat range, using various methods. The result's, however, have been only partly satisfactory, owing to experimental difficulties. The present investigation had as it's immediate inception an address by J. V. Emmons, of the Cleveland Twist Drill Co., to the Columbus Chapter of the American Society for Steel Treating in 1931, in which he deplored the fact that comparatively little was known with regard to the hardness of high-speed steels at elevated temperatures, in spite

Jan 1, 1933

THE object of all classification is to group together things which are alike, and separate those which are unlike. This object is essentially a practical one, enabling us to apply past experience to new conditions: Many costly large-scale experiments lose half their importance for want of proper description of the coal used, and the consequent impossibility of predicting other coals will behave in the same way. I do not, therefore, make a fundamental distinction between "scientific" and "use" classifications, except in so far as use depends on conditions, such as size or impurities which are not related to the nature of the coal substance itself. The characters chosen to define the classes of coal must be such as are accompanied by as many other properties as possible. It is not to be expected that any system of classification will enable us to predict every property of coal, since all specimens have an individuality of their own. But specimens can be grouped by a number of resemblances into species. Further, species which resemble each other can be grouped into genera.

Jan 1, 1928

By R. H. Sweetser

There are probably as many variations of the method for blowing-in blast-furnaces as there are furnace superintendents. That some of these variations are poor practice is shown by the troublesome and sometimes disastrous experiences of many furnace-men, even within the last few years. It is the object of this paper to put on record a blowing-in practice that has gradually developed to the point where the results are sure, safe, and satisfactory; and also to bring into discussion several variations that are questionable. The blowing-in of a modern blast-furnace is one of the greatest of metallurgical operations. On its degree of success depends much of the future life of the lining and the subsequent behavior of the furnace; and it involves possibilities of danger to the men engaged in the work. The objects to be attained are the heating of the interior of the furnace to the high temperature necessary for smelting iron; the starting of the smelting process; and the gradual movement of the stock in its downward course. The most critical points are the placing of the kindling-wood, the " bringing down " of the gas, the closing of the iron-notch, and the first cast. The lighting of the first gas, the opening of the cinder-notch for the first flush, and the running of the first cast are anxious times for the superintendent and the furnace-men. Drying-Out the Furnace. As soon as a furnace-lining is completed it should be thoroughly dried out, whether it is to be blown-in soon or not; and the longer it is dried, the better for the furnace. At least two weeks is desirable; but good results can be had with 10 days of firing. The crudest and least desirable method of drying is to build a wood fire in the bottom of the furnace, throwing the wood in through a tuyere-arch, and using the iron-notch for

Jan 1, 1913

By L. C. Snider

During the past few years a number of large and highly productive oil fields have been discovered in the United States. The immediate oversupply which has resulted, together with the circumstances under which the new fields have been operated, has created exaggerated impressions of the importance and magnitude of these fields. Statements as to the many years during which individual fields could supply the entire demand of certain areas, as to the overwhelming effect of these fields on the industry, and as to their greater size compared with any of the older fields have become so common as to attract little attention. For example, East Texas is commonly considered as the "greatest oil field" and a review of the development of the field for 1931 is so headed in one of the leading trade journals.' East Texas is unquestionably a very great oil field. However, some students of the field have estimated its ultimate recovery at about one billion barrels, and the Bradford field discovered in 1875 is also estimated, by competent engineers, to have about a billion barrels still recoverable by water drive, in addition to more than 300,000,-000 bbl. it has already produced. If East Texas should produce the two or three billion barrels assigned to it by more optimistic estimators, it will, though considerably greater than Bradford, still fall far short of it in importance to the industry. A reasonable doubt also exists as to whether East Texas will exceed the Midway-Sunset field which has produced about 720,000,000 bbl. and still has important reserves. Again, in importance to the industry, Midway-Sunset has been greater than East Texas can ever be. Relative Importance of Oil Fields The principal purpose of this study is to compare, on the basis of their importance to the industry, a considerable number of the major fields which have been developed in the United States. Some remarks are also made as to the estimates of reserves in certain fields now in course of development, since the writer believes that the conditions under which these fields are operated lead to estimates of recoverable reserves which

Jan 1, 1933

This paper "On Coal" was published in three issues of The Western Gleaner in 1814. Name of author is not given. This magazine was started by Cramer, Spear & Eichbaum, in Pittsburgh, Pa., in December 1813, and ran for about two years. Copies are very rare, and this one is made from an original in the Darlington Library, University of Pittsburgh. This is almost certainly the first general article on coal published west of the Allegheny Mountains, and one of the earliest in this country. ON COAL Its Natural History-Mining of Coal-Phenomena occasioned by Fire-damp-Method of Coking-Distillation of Tar from Pit-coal-Gas-light-Coal, a Manure I. NATURAL HISTORY OF COAL There are few productions of nature which present to the philosopher a wider field of investigation than pit-coal. A substance highly inflammable is found in the deep recesses of the earth, sometimes loaded with numerous superincumbent strata of hard rock, and extending frequently along with these strata through a vast expanse of territory. Though metals may be said to be inflammable substances, as they combine more or less rapidly with oxygen when placed under particular circumstances, yet the character of rapid combustion with disengagement of light and heat, seems to belong. principally to such substances as are derived either from the animal or vegetable kingdom. That this is probably the case with regard to coal we are further induced to believe, by the remarkable circumstance, that the chemical analysis of this natural production yields especially, though in various proportions, those materials which constitute essentially the vegetable. And if any thing was wanting to confirm, us in that opinion we might trace in a number of fossile substances the gradual transition of the vegetable into the state of mineral coal. This fact is so intimately connected with the natural history of coal, that we cannot think it superfluous to give it some farther development. Among the great number of principles which the chemist is capable of tracing in the vegetable kingdom, the presence of extract, resin and fibre seem to form the characteristical marks of plants.-If vegetable matter be boiled in water, and the water, after having been strained and filtered, be exposed for some time to the open air, a flocculent precipitate takes `place from every part of the liquor; which soon subsides to the bottom of the vessel containing it. This is the extract; altered, indeed, by exposure, and now no longer soluble in water, a change which is supposed to depend on the absorption of oxygen; and if, by any means the proportion of oxygen be increased, the extract gradually becomes of a darker color, blackens, and approaches to the state of charred wood.

Jan 1, 1942

By Giovanni Barla, Stefan H. Boshkov

This paper examines the application of gelatin mixture models to the study of factors such as gravity effects, tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space. The technique of calibrating gelatin mixtures proposed by Richards and Mark in 1966 is applied to the particular problem considered. Similitude relationships between model and prototype are discussed with reference to the constitutive equations describing the physical behavior of the rock mass. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example with the view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The prediction of the displacement, stress field and mode of fracture associated with a given rock structure, its initial stress field, and its physical properties is essential to rock mechanics and ground control. The basic approach is to assume the rock mass to behave as a continuous, homogeneous, and isotropic medium. The classical theory of elasticity is the simplest theory based on such a concept. Specification of the elastic constants, the initial state of stress in the ground, and the boundary conditions on stress and displacement allows one to predict stress and displacement within the body. Subsequently, provided that a criterion which governs rock fracture under various stress conditions has been established, a stability analysis of the rock structure can be performed. A natural extension of the present knowledge consists of removing some of the simplifying assumptions which characterize the analytical solutions based on the classical theory of elasticity. Complex geometry, the significance of tectonic and residual stresses, anisotropy, physical nonlinearity, time-dependent behavior of the rock mass and connectedness of the geologic space are some of the important factors which are neglected in the classical approach. A better insight into the real problem can be attained with either the finite element method of stress analysis or an experimental technique. The former has already been applied with success on several occasion 1-4 and is destined to render great service in the field of rock mechanics and ground control. The latter, which will be considered in this paper, has been used extensively in applications too numerous to be enumerated. Experimental technique involves either prototype testing, if the area to be studied is accessible, or model testing. Two- and three-dimensional photo-elastic analyses are very convenient means of obtaining the stress distribution in models of complex geometry. In general, such analyses are confined to studies of stress fields around openings which are sufficiently far removed from the surface boundary so that the stresses in their neighborhood are practically equal to those produced by an initial uniform stress field; i.e., so that gravitational effects are negligible. There are, however, many rock structures where these effects must be taken into account to attain a more realistic representation of the problem. Surface and near surface rock structures, systems of openings interacting with one another, and structural components loaded only by their own weight are some of the obvious examples. This paper was written to show how factors neglected in the usual analysis based on the classical theory of elasticity, can be taken into account when gelatin mixture models are used inconjunction with photoelastic methods. The interaction between two openings in a linearly elastic medium, under conditions of plane strain, is used as an illustrative example, with a view to describing the history of stress and deformation changes on the rock medium and lining around a slusher drift while undercuts are made in block caving. The birefringence of gelatin mixtures has been known for some time. A series of experiments were carried out by Rossi in 1910,5 but after that very

Jan 1, 1970

By T. A. Klinefelter

Lightweight concrete aggregates are materials weighing less than the usual aggregates of sand, gravel, and crushed rock. Concretes made with sand and gravel or crushed rock weigh 145 to 150 lb per cu ft, compared with 50 to 90 lb per cu ft for concretes made with lightweight aggregate. The ultra-lightweight concretes weigh much less than 50 lb per cu ft. Lightweight aggregates may be natural or manufactured materials, or byproducts from other commercial operations. Natural materials include pumice and pumicite, tuffs, breccia, scoria, diatomite, and vegetable products, such as peat, straw, and sawdust. Manufactured materials include expanded perlite, vermiculite, slag, clay, shale, and slate. Byproducts include cinders, aircooled slags, and coke breeze. Concretes made with lightweight aggregate were used first in construction of commercial buildings, later in homes. Present usage is general in multistory and other building construction, such as bridge decks, barges, jet-plane runways, piers and other structures. The industry has grown remarkably in the last decade. General Considerations The particular use to which the concrete may be put determines the importance of the various properties of the aggregates employed. Any given type of aggregate, however, should be reasonably uniform in composition and properties. It should be suitably graded and maintain proper weights, insulation values, and adequate strength to prevent breakdowns in mixing. It should bond properly with the cement, be inert to chemical reactions with cement and steel, and resist weathering, moisture, insects, and fungi. Some properties of any given type of lightweight aggregate from different suppliers may vary considerably because of differences in the source of raw material and the method of treatment. This statement applies particularly to expanded clays, shales and slates. All lightweight concretes have higher absorption of moisture and lower thermal conductivity, lower compressive strength, as well as lower unit weight as compared with standard concretes made with sand, gravel or crushed rock. Excepting cinders, the cost of lightweight aggregates is usually higher. Grading and unit weight requirements are given in ASTM standards: C 330-53T, Lightweight Aggregates for Structural Concrete; C 331-53T, Lightweight Aggregates for Concrete Masonry Units; C 332-54T, Lightweight Aggregates for Insulating Concrete. The production of masonry units shows the growth of the use and types of lightweight aggregates. In 1947 the total number of lightweight block was 460,000,000 units in 8 by 8 by 16-in. equivalents. By 1954 this had increased to 950,000,000 units. Of the 1954 production, 27 pct was of manufactured types, 43 pct of cinders, and 30 pct of remaining types. Raw Materials Used as Lightweight Aggregates It was stated above that a variety of products both natural and manufactured are used as lightweight aggregates. It is easy to understand that a bulky material of low unit value cannot be transported far and still remain a low cost product. Hence the product used in a particular market depends upon the availability of the possible raw materials. Thus it is

Jan 1, 1960

By Paul D. Foote

Most of the treatises on metallurgy intimate that simultaneously with the development by the atomic physicist of a really satisfactory theory of the atom will be inaugurated a new epoch in the science of metals. Metallurgically and metaphorically, we shall dwell in the Utopia of Sir Thomas More. It is my privilege this afternoon to demonstrate that this state has not arrived. An atom is a miniature planetary system consisting of a positively charged nuclear sun about which revolve electrons each carrying the negative charge e. The charge on the nucleus is + Ze where Z is the atomic number and the number of planetary electrons in a neutral atom is equal to Z. These electrons are arranged in several groups having different binding energies. Ordinary x-ray phenomena relate to processes occurring deep within the atom, usually with electrons in the so-called K or L shells. Such electrons in the heavier atoms are so closely bound to the nucleus that the forces exerted by neighboring atoms in a solid are relatively inappreciable. For most practical x-ray investigation, the atom may be considered as in the gaseous phase completely isolated from its neighbors. The K radiation from an element in the gaseous state, in the solid or liquid phase, or even in combination with other elements in all its possible valences, is almost identical.‡ Visual and ultraviolet spectroscopy is concerned with disturbances of the most loosely bound outer or valence electrons of the atom, always in the vapor state. The remarkable progress of the last year in both theo-

Jan 1, 1926

By William A. Johnson

THE mathematical analysis of diffusion curves in solid metals is Carried out ordinarily by analogy with the flow of heat in a continuous medium and no account is taken of the fact that the materials involved are composed of discrete particles that move discrete distances at irregular intervals. It is possible to treat the problem on the basis of simple assumed atomic mechanisms, in which case, because of the small scale of the elementary process compared to the gross effects observed experimentally, the two procedures lead to the same expression for the variation of concentration with distance. Thus, for engineering purposes, the usual methods are quite satisfactory. If, on the other hand, our purpose is to go beyond the mere collection of data, however desirable this may be, it is necessary to recognize and understand the factors that are of fundamental importance. One factor that has not hitherto been considered when dealing with solid metals is the difference in atomic weights of the isotopes of a single metal. While all the atoms of a given element are alike chemically, their weights may vary by a small but significant amount, and atoms of different weights may have different diffusion rates. With gases this variation in isotopic weight produces a change in the rate of diffusion by a factor inversely proportional to the square root of mass. While, except for the lightest gases, this is not a large effect, it is, for example, sufficient to permit a considerable concentration of one isotope at the expense of others. If metals exhibit a similar phenomenon, some modification of the analysis of the diffusion process will be required, since the different isotopes of a given metal will have different probabilities of moving and the heat-flow analogy will contain a fundamental error. This situation cannot be rectified by using a diffusion coefficient based on the average probability of moving, and it can be shown that even when the diffusion coefficient is independent of composition, the diffusion curve will not agree with the simple theory except in the rare cases where only one isotope exists; e.g., gold. If, however, the mass effect in the solid state were no larger than in the gaseous, the errors arising therefrom in the analysis of ordinary diffusion curves would be quite negligible. Nevertheless, our desire to obtain all possible information concerning the details of the diffusion process, and the possibility of diffusion in the solid state as a means for separating isotopes are cogent reasons for undertaking an experimental study to determine whether isotopes of different masses diffuse at different rates. EXPERIMENTAL PROCEDURE If isotopes of different masses diffuse at different rates, the ratio of the concentration of one relative to another will vary with the distance from the diffusion inter-

Jan 1, 1946

By T. Prof. Ph. D. Egleston

(Read at the Amenia Meeting, October, 1877.) THE copper-bearing rocks of Lake Superior are composed of a series of metamorphic rocks, comprised under the names of amygdaloid and conglomerate, in which the copper and silver found with them are pseudomorphs. These rocks, generally, have well-defined walls which cause them to separate easily. Generally, the country rock is sterile, but it occasionally rises into the copper-bearing rock, and then carries copper. Usually, the amygdaloids carry copper, and the greenstones or melaphyres which encase them do not. There is a very generally received opinion that the copper in these beds occurs in shoots. This does not appear to be proved, though the opinion seems to have some foundation from the experience of the Calumet & Hecla Mine, where a body of poor rock has been left, which, on the mine map, shows a general direction. The theory may be true of that individual mine, but too little work has been done in the other mines to draw any decided conclusion. The copper is very unequally disseminated in the rock, if any given piece be taken as an example, but, if the whole copper-bearing series be considered, its distribution is uniform. It may prove that there are certain directions in which the copper has been deposited more abundantly than in others, and these may be found to correspond with certain geological causes, but up to the present time the knowledge gained is not sufficient to warrant any general conclusion. These rocks are supplemented by a series of true fissure veins, of which there are several systems, making the amount of native copper very large. Unfortunately, except in the fissure veins, known as "mass-mines," the copper is so scattered through the rock, and is in such a fine state of division, that, although it is not always difficult to mine, it is always difficult to dress it sufficiently too make it pay. The metal is so uniformly distributed through these copper-bearing rocks that detached pieces, called " float," are found in digging on almost any land in the country. These pieces vary from very small fragments, weighing not more than a few ounces,, up to many pounds. III one instance, in making an excavation for a cellar of a

Jan 1, 1878

By Harry A. Wahl

Precent fracture design procedures are bared on the total fracture area created. A method to distinguish beI,,.ecn total area and [he propped or effective fracture area has not been available. This paper presents a solution to this problem, applicable to horizontal fractures. The difierences between effective fracture area and torn] area are demonstrared in example calculations. This work is hayed on experimentally determined transport efficiencier of solids in sand-liquid slurries. Newtonian and non-Ne~vtoninn systems are considered. INTRODUCTION Fifteen years after commercial introduction, hydraulic fracturing remains the most successful stimulation technique in the oil field. This success is primarily due to ability of induced fractures to penetrate and alter permeabilities deep within formations. Many fields producing today could not have been developed without the hydraulic fracturing process. Because of wide usage, fracture-treatment design has received a great deal of engineering and research effort. This work, resulting in improved equipment and materials, has increased the benefits from fracture treatments as well as the applicability of the process. A major contribution was the development of fluid-loss additives. Necessarily, the number of parameters to be considered in treatment design has steadily increased, resulting in more complicated design techniques. Almost all present design procedures are based on the precepts set forth by Howard and Fast. Relating the fluid volume lost into the formation, the volume required in extending the fracture, and the total slurry volume injected, they developed an expression for the total fracture area created in terms of pertinent treatment parameters. Fluid loss during treatment was expressed as a function of time for three flow mechanisms. Although modifications of fluid loss equations have been made, the total fracture area concept has remained unaltered. A vast amount of field data indicate that induced fractures must be propped and held open to be effective. A notable exception is the Mesa Verde formation in the San Juan basin. However, analysis of these treatments shows that improved well productivities are obtained when propping agents are incorporated in the treating fluid. Although propped fracture area has been recognized as an important design parameter, a method to distinguish between total area and effective fracture area has not been available. The necessary information on slurry-sand transport in fractures has been lacking. Interest in the propped region of induced fractures is not restricted to areal extent alone. The distribution of sand within fractures is important from the standpoint of fracture flow capacities. Flow capacity affects the increase in well productivity after stimulation. The work of Huitt and Darin4 hows that partial monolayers of sand have large flow capacities compared to thick* dense sand packs. It has been postulated that gelled fluids have the ability to transport sand within the fractures at the deired low concentrations. An early contribution in the area of sand placement in fractures was made by Kern et al.' They studied sand movement in a transparent vertical fracture model. It was observed that the sand tended to settle out in the bottom of the model before moving very far. When the fluid velocity exceeded a certain critical value, all of the sand injected began moving through the crack even though it settled to the bottom. This critical velocity was determined under several flow conditions. Some work on sand movement in horizontal fractures has been reported in Russian publications. Sand movement was studied by Izyumova and Shan'gin' using a transparent "pie-shaped" flow model to simulate a horizontal radial flow system. However, the data were limited, especially in a quantitative sense. Dorozhkin, Zheltov and Zheltow studied the behavior of sand-liquid slurries in a horizontal linear flow model. The quantitative data were restricted primarily to the thickness of sand deposits formed at the bottom of the fracture. An earlier paper provided basic data on the flow of sand in horizontal fractures. This study was designed to yield specific quantitative information on rate of advance of sand particles and pressure behavior under various flow conditions. A comprehensive photographic study was undertaken in a 10-ft windowed flow cell to provide the necessary qualitative and quantitative data. Since the number of potential variables far exceeded the capacity of the initial study, emphasis was placed on the effects of sand concentration, oil viscosity and oil flow rate. A detailed description of these experiments and the results are described in Ref. 9. However. the implications of this work on the fracture design calculations were not discussed. An analysis of these data as well as new data is provided in the following sections. EXPERIMENTAL RESULTS The primary objective of the experimental investigation was to provide information on the rate of advance of the solids in sand-liquid sturries. A 10%-ft long transparent

Jan 1, 1966

By T. Egleston

The importance of condensing the gases which escape from furnaces so as to save both the fine particles of ore carried off mechanically and those which are volatilized, has for a long time occupied the serious attention of metallurgists in all parts of the world. It was my good fortune during the last summer to visit the lead and silver works at Ems, near Coblentz on the Rhine, and through the politeness of Mr. Freudenberg, general director of the works, to study in detail their methods of condensation, and to receive from him the important results which have been obtained through a series of experiments lasting over a number of years. I have thought, that these results would be of great interest to the members of the Institute and to other metallurgists in the United States, and I have, therefore, with the assistance of Mr. Freudenberg, prepared a careful, detailed description of the construction of the flues, as well as an account of the various experiments which have been made with them, and the conclusions arrived at as the result of these experiments. It may be said, in general, that the reason why so little attention has been paid in the metallurgical works of the United States to the collection of flue-dust, is that we are not generally aware of the large amount of material carried off by the gases. This is owing partly to the fact that little or no attention is paid to the subject, and also to the fact that the assays, which are almost invariably made in the dry way, show a result so much below the real contents

Jan 1, 1883

By G. W. Housner

The series of earthquakes in the vicinity of Koyna Dam in south- western India, which included a very damaging magnitude 6.5 shock on Dec. 11, 1967 (Dec. 10 GMT), is of much interest. The events are exceptionally well documented, which is a tribute to Indian geologists, seismologists, and engineers. To help in disseminating the information in the United States, this chapter presents a brief summary of the pertinent data and lists references. Koynanagar (Koynatown), which began as the construction camp for the dam, is located about 140 miles southeast of Bombay and 70 miles south of Poona at 17.4ºN and 73.7ºE, about 40 miles inland from the Arabian Sea. Koyna River flows almost due south from its source a distance of about 38 miles and then makes an abrupt turn to the east and travels some 480 miles to empty into the Bay of Bengal. Koyna Dam is located about 3 miles north of this turn. The approximately north-south trending continental divide is a few miles west of Koyna and the terrain drops steeply about 1700 ft to where the hydroelectric generating station is located. The reservoir behind Koyna Dam forms a long, narrow lake (Shiva- jisagar Lake) with mean water level (MWL) at 2160-ft elevation. The 345-sq-mile watershed receives an annual rainfall of about 200 in., most of which falls between mid-June and mid-October. The peak storage is 99 x l09 cu ft. A controlled flow passes under the continental divide in a tunnel and then down to the electric generating station about 5 miles WNW of the dam. The inflow not used for power generation is released to Koyna River. The Koyna project is a major source of electric power for Bombay and produces 540 MW at peak load.

Jan 1, 1970

By Douglas J. Robinson

A pilot scale process has been developed to separate mercury, tin, silver, and copper from dental amalgam scrap. Laboratory research led to a process which was operated in 55 gallon drum sized reactors to treat 2000 Tr oz charges of scrap per day. This paper discusses the development work, presents a flowsheet and gives an indication of the equipment necessary to carry out the process on a commercial scale.

Jan 1, 1984

By L. D. Anderson

WHEN, after years of troublous experiences in roasting sulfide ores with heavy dust and fume losses resulting from the equipment and methods first available, there appeared on the scene of metallurgy that revolutionary process known as sintering, it was felt that at last there had been found the ideal method for preparing sulfide ores for blastfurnace reduction. Not only were the sulfides roasted but also the fine oxidized ores were bound together with them in strong porous cellular masses which were in the best possible condition for reduction. With the experiences gained in the manipulation of the Huntington-Heberlein, Carmichael-Bradford, and Dwight & Lloyd processes there developed a refinement of detail which brought the whole plan of roasting by sintering to a high plane of perfection. But that metallurgy is never stationary is revealed by the fact that changes in milling practice, particularly the development of flotation, have introduced a new set of problems in sintering itself. Inasmuch as it is felt that these problems have not yet been solved in an entirely satisfactory manner this paper is written to record the present practice of the Salt Lake Valley smelters with the hope that there will be brought forth such discussios as may perhaps lead to still better practice. By far the greater proportion of the sulfides smelted today are flotation concentrates. Usually they are high grade, sometimes as high as 70 per cent. and more in lead. They are extremely fine, many mills grinding the ore so that from 60 to 80 per cent. will pass through screens of 200 mesh. The physical condition in which many of these concentrates reach the smelters is disconcerting to the metallurgists. Some are of about the consistency of putty. Others are of a sticky, slimy nature. Others again, dried to the limit, are veritable powders. Remembering that the down-draft sintering charge for the best results must be porous enough to let air be drawn through it reasonably well, must be thoroughly mixed, and must have some coarse material in it to segregate out and form a layer on the grates, it will be understood that the advent of this extremely fine material has made necessary still further elaboration in the equipment and processes of preparing sulfides for the blast furnaces,

Jan 1, 1929

By Frederic E. Carter

There have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

By Charles White Merrill

Mankind's progress is measured in minerals. Man's emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate--and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium as a metal appeared as a commercial product only in 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1959

By W. M. McCardell, W. O. Winsauer

The abnormal conductivity found in shaly reservoir rocks containing an electrolyte is shown to be a consequence of the electrical double layer in the solution adjacent to charged clay surfaces. This increased conductivity results from a higher concentration of ions in the double layer than in the solution in equilibrium with the double layer. It is shown that the magnitude of the increased conductivity of a shaly reservoir material is influenced by the concentration and type of ions in the equilibrium solution as well as by the colloidal nature of the rock. INTRODUCTION An important factor in the quantitative interpretation of the electric log is the resistivity factor of reservoir rock. The resistivity factor is defined as the resistivity of the rock when completely saturated with an electrolyte divided by the resistivity of the electrolyte itself.' In the normal case, the resistivity factor for a particular rock sample is independent of the resistivity of the electrolyte and reflects the pore geometry of the rock.' In 1949. Patnode and Wyllie' showed that in some cases the resistivity factor is not constant, but instead varies with the resistivity of the electrolytic solution. It was shown that clean sands behave normally—i.e., that the resistivity factor does not vary with resistivity of the electrolyte — but that sands con- taining shale and clay may exhibit abnormally low resistivity factors when the solution used to saturate them is of fairly high resistivity. At low resistivities of the electrolyte, the resistivity factor for a shaly sand appeared to approach a normal behavior. It is evident that the resistivity factor of a shaly sand is dependent upon factors other than pore geometry when the solution used to saturate it is of high resistivity. Patnode and Wyllie, and later de Witte,' assumed that the conductivity of a shaly sand saturated with an electrolyte could be represented as the sum of two quantities. One of these was assumed, in effect, to be the conductivity which would be expected if the sample were a clean sand. and the other was assumed to be a conductivity inherent in the sample itself. The latter was supposed to be constant for a given rock sample regardless of the solution used to saturate it. The source of this added conductivity was ascribed to "conductive solids." In actual practice: the effect of the abnormal behavior of shaly sands is of minor importance except when the resistivity of a formation such as a sand is high. Thus the effect is more important when the sand is saturated with a dilute brine than when it contains a more concentrated electrolyte. The effect is also more important when the sample contains oil or gas than when it contains only saline water. Recently it has been suggested that the porosity of a stratum may be estimated from the electric log by use of the resistivity of the invaded zone." This is the zone flushed with the filtrate from mud used in drilling the well. which is ordinarily very dilute brine. When the method is applied to shaly sands, the effect of abnormal conductivity becomes of importance. This report describes an investigation of the mechanism responsible for the abnormal behavior of the resistivity of shaly rock saturated with conducting solutions. The investigation

Jan 1, 1953

By John V. Beall

Given: One large, but dated open-pit copper mine and processing plants, down about one third in production capacity in decade because of declining ore grade. Solve for: Restoration of former peak capacity without further losses during period of reconstruction. That is the problem that Kennecott's Utah Cop- per Division began solving in 1963. Most of the work went to a task force of engineers, several of whom were plucked out of line jobs and assigned to the so-called "Expansion Project" for the duration. There was no doubt from the beginning that effective cooperation between Expansion Project engineers and operators was critical to success, and personnel was chosen accordingly. This foresight paid off. The Expansion Project is all but complete, and the Utah Copper Division is returning to its rated capacity of 300,000 tons per year of copper metal.

Jan 6, 1967

By E. R. Borcherdt

METHODS and equipment are subject to study in the Butte district at all times in order that advantage may be taken of any new developments that might serve to increase efficiency and lower costs. Detailed time studies of each operation involved in the entire mining process have been of invaluable assistance in analyzing the individual operation for possible improvement. In other words, the fact that a practice has been in vogue for many years does not exempt it from change provided an easier and cheaper method can be found. EXPLORATION Ore occurs in the Butte district in such manner that structures must be drifted on, no matter how small or unimportant they appear when intersected by a crosscut. Parallel structures also add to the crosscut requirements. This prospecting work, which formerly was done entirely by drifting and crosscutting, is now being supplemented by diamond drilling, to aid in greatly decreasing the amount of waste. In long-shot prospecting, or in second or third class prospecting, where the chances of developing commercial ore are not very great, diamond drilling is of particular value. In prospecting where chances of encountering commercial ore are certain or where crosscuts can be used later for haulage or ventilation, drilling obviously is not applicable. Improvement in drilling machines and bits has contributed greatly to the present success of diamond drilling. STOPING For many years square-set filled stoping was the principal mining method used in the Butte district. Later timbered and untimbered rill stopes were used, also some horizontal cut-and-fill stoping where both ore and walls were particularly strong. Because of the amount of timber required for square-set stoping, and the relatively low production per stope unit, experiments with horizontal cut-and-fill stopes were begun in ore bodies of which many had fairly weak walls. It was felt that increase in the speed of the stoping operation, followed closely by filling, to avoid weight being produced by permitting ore and walls to remain insufficiently supported over comparatively long periods, would maintain the walls and backs in safe condition without the use of timber and without ore dilution from wall slough. Cycles of drilling, scraping ore, and filling were devised, which have materially increased stope production and decreased timber consumption, so that both stope labor and supply costs were lowered appreciably without materially affecting grade control. In the larger mines of the district, where wide veins favor this stoping method, half of the total production is now being mined by horizontal cut-and-fill stopes (Fig. I). The increase of the filling rate demanded by the increased stoping rate was the greatest obstacle encountered in the accelerated stoping operations. Finally this problem was solved by replacing the time-honored method of transferring filling waste by small cars, which were hoisted or lowered in the auxiliary shaft, by a transfer

Jan 1, 1941