Search Documents

By Eldon Dunlap

RECENTLY the producing branch of the petroleum industry has shown a considerable and growing interest in the quantitative determination of the water, oil, and gas content of cores as it relates to estimation of reserves, to providing a, basis for judging as to the feasibility of applying various secondary-recovery and pressure-maintenance processes, and in general to the operation of producing properties. For years it has been known that oil, gas and water coexisted in the pores of many semidepleted oil measures. It is now generally believed that oil-bearing beds contain connate water in amounts varying up to 50 per cent of the pore space. However, only lately has reliable direct evidence of the extensive occur-rence of connate water in oil sands been published. Very little work has been done to ascertain the effect of this water on the productivity and ultimate recovery of oil from wells. It was the intent of this research to study the influence of this indigenous water on the flow of oil through unconsolidated sands, with the hope that the results could be applied qualitatively to the flow of oil in underground reservoirs partly saturated with water. Obviously, ultimate recovery estimates based on the void volume of the reservoir will be in error unless a, conscious or unconscious correction is made for the volume of water occupying a portion of the effective pore volume of the reservoir- Evaluation engineers in the past have applied arbitrary saturation and recovery factors that may inadverently have compensated for the failure to consider specifically the water content. Nevertheless, the evidence available indicates that these factors need revising if each is to be independently correct and truly representative. Although the mere fact that the connate water renders part of the pore volume of the reservoir incapable of containing oil is of primary importance to the operator, it is also of interest to know whether and to what extent the presence of varying amounts of interstitial water influ-ences the permeability of the sand to oil.

Jan 1, 1938

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By C. P. Proctor, J. B. Morrow

With numerous plans under consideration for coal classification, and with the advent of the Bituminous Coal Code, the intelligent sampling of coal has become increasingly important. To us it is rather significant that there have been very few fundamental studies of coal sampling in American technical literature since those of E. G. Bailey, which appeared in the Journal of Industrial and Engineering Chemistry in March, 1909. He covered the subject up to that time so thoroughly and in such an excellent manner that perhaps many other later students have felt that they could add very little to his findings. The recent studies of the British Engineering Standards Association have indicated the possibility of a somewhat different interpretation of Bailey's results, permitting the taking of smaller samples, and perhaps it will now be helpful to reopen this question. C. W. H. Holmes, in an informative series of articles on coal sampling recently published in Colliery Engineering, makes two rather interesting statements, as follows: It is scarcely surprising to find a lack of interest and knowledge regarding the sampling of coal not only in the mining industry itself but also among consumers of industrial fuel: at its best coal sampling is a dirty business, regarded as a nuisance and an expense by the commercial man, and usually as a nuisance and nothing else by the chemist. The writer can conceive only two classes of people who have never experienced any difficulty in obtaining representative samples of coal from wagons; those who have never tried to, and those who have never had the necessity or desire to check the accuracy of their work. The primary purpose of this paper is to present some tabulated data of the more significant results of a sampling investigation undertaken during the last four years to obtain certain fundamental data on the variables connected with coal sampling and to point out that often assumptions have been made that are not in accordance with the facts. One of the standard sampling methods states:

Jan 1, 1936

By T. A. Rickard

From time immemorial the fissure-vein has been held the simplest type of ore-deposit. The prominence given to it by Cotta and his disciples, from their study of the mines of the Erzgebirge, is impressed upon technical literature; and, in consequence, the ores which carry the valuable metals have been supposed to occur mainly in fissures, cleaving the rocks in diverse directions, and the noblest type of vein has been deemed that which cut across the country independent of its structure, whether evidenced as bedding, foliation or cleavage, and which was identified with rents produced in the rocky crust of the earth. As so conceived, the vein was a fissure filled with ore, extending through the country for a varying distance, and continued downward to a depth more or less proportionate to its longitudinal extent. The vein-material was bounded by an encasement of rock, and those immediate surfaces which limited it on either aide were called " walls." These primary conceptions have become modified by the experience of modern mining in widely separated regions. The study of lode-formations has led to the recognition of notable departures from the supposed normal structure of the veins of Saxony and Cornwall, the two classic homes of early economic geology. Typically the walls of a vein are conceived as parallel rockplanes enclosing the ore; the upper one being called the " hanging-," and the lower the "foot-wall."* Walls are rarely alike. Even where a vein traverses a homogeneons formation, such as a massive crystalline rock, it is usually found that the surface which bounds it underneath

Jan 1, 1897

By L. Douglass Anderson

Fox some years past the annual reviews of the metallurgy of lead have almost uniformly stated that there have been no great changes, such as there were, being more particularly noticeable in the refinement of details. While this is quite true, nevertheless these changes in details are gradually bringing about a condition that, taken as a whole, constitutes a considerable advance in the art. Local circumstances have often -compelled metallurgists to adopt certain peculiarities of practice which -upon trial have been found advantageously applicable to more than the restricted district f origin. This paper will deal ' with some of the more novel features developed in recent years at the United States smelter, Midvale, Utah, particularly with reference to the influence of the bag house. The plant is equipped with six blast furnaces, 48 by 160 in., mechanically fed; four Wedge furnaces for roasting matte and sulphide ores; four Dwight-Lloyd sintering machines; 20 converter boxes for blast roasting; storage bins for ore, fuel, and fluxes; "oxide" and "sulphide" sampling mills; bag house taking all the gases of the plant; arsenic plant for treating the dust gathered there; laboratory, shops, etc. The most marked feature of the plant is its complete bag-house system. Of the many schemes thus far tried for preventing damage to surrounding agricultural interests the writer is aware of none as yet quite as efficient as the bag house. A common remark of visitors upon approaching the plant and viewing the clear stacks is that it appears to be shut down, whereas once inside all the evidences of industry are found.

Jan 7, 1914

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

By Robert L. Bates

Definition An industrial mineral, says the Glossary of Geology, is "any rock, mineral, or other naturally occurring substance of economic value, exclusive of metallic ores, mineral fuels, and gemstones; one of the nonmetallics." Probably most geologists and engineers would accept this simple and straightforward definition, at least as a general statement. On analysis, however, certain anomalies crop up. For example, it may be considered arbitrary to include industrial diamond and corundum and to exclude their precious varieties, gem diamond and sapphire. So the present volume has a section on gems and gem materials, in spite of the definition. Another problem arises when we try to define precisely what is metallic and what is nonmetallic. Bauxite and ilmenite certainly qualify as metallic ores, but both are also raw materials of important nonmetallic substances; hence they are included in the book, A third anomaly is that, by common consent of geologists, engineers, mineral economists, and others concerned, the term industrial minerals may include not only rocks and minerals but also certain manufactured products like cement and lime, and even mixed groups of natural and artificial products, such as abrasives and refractories. Thus the central realm of the industrial minerals is clear enough, but its boundaries tend to be indefinable. Since a definition that allowed for every irregularity in the outer fringes would be excessively unwieldy, the one quoted above may be considered satisfactory. The expression industrial minerals is commonly equated with nonmetallics, and with the somewhat more precise phrase industrial minerals and rocks as in the title of this book. Characteristics of the Field The industrial minerals as broadly interpreted are a highly diverse group of materials; indeed, we may say paradoxically that diversity is about all they have in common. At one end of the spectrum are ordinary earth materials such as gravel and crushed stone, with a value of perhaps $3 per st; at the opposite end are industrial diamonds, which sell (by the carat) at the rate of roughly $18,000,000 per st. Neither the metals nor the fuels, and few if any categories of manufactured products, include items that differ in value by more than six orders of magnitude. Most gravel and stone are of no value unless close to a market; diamonds and other exotic substances possess such unique and desirable properties that their occurrence in remote corners of the earth is no deterrent to their use. The broad range of industrial minerals falls between these extremes of unit value and place value. The industrial minerals penetrate the entire fabric of modern industrialized society, from such fundamental operations as drilling for oil and smelting iron ore to the manufacture of virtually the whole array of consumer products. There is no industrial-minerals industry; there are many industries. The simple term field is convenient as an all-inclusive expression. An industry is considered to belong in the industrial-minerals field if its operations consist of extraction and processing, but not manufacturing. Thus the mining and beneficiation of feldspar is a mineral industry, but the manufacture of ceramic products is not. In the cement and lime industries, processing merges into manufacture, and the line is less distinct. It disappears altogether in a plant that extracts salt as artificial brines, and makes sodium and chlorine chemicals, all under the same roof. An aspect of some industrial minerals that differentiates them from the metals is that their physical properties carry over into ultimate use of the product. Such minerals as mica, asbes-

Jan 1, 1983

By A. M. Abouzeid, S. Chander, D. W. Fuerstenau

Today numerous ores contain valuable minerals in finely disseminated form; and although the recovery of these fine mineral particles is generally exceedingly difficult, diminishing raw material resources necessitates the recovery of such mineral values. In many systems, the efficiency of recovering fine particles is still extremely low and often fine particles must be discarded as slimes. However, in recent years, various advances have taken place in the recovery of mineral particles in the very fine size range. In this paper, the background and performance of a number of processes for fine particle processing and separation are reviewed and discussed, particularly from the point of view of how fine particle recovery might be improved.

Jan 1, 1979

By C. R. Hayward, H. O. Hofman

The aim of instruction in a metallurgical laboratory is to make real the principles on which metallurgical processes and operations are based, and to foster the spirit of investigation. The materials with which experiments are carried out are ores, metals, and metallic compounds. The method varies with the end sought. A class may work as a whole, each member contributing his share to the solution of a problem, or the students may carry on investigations independently; the former exemplifies class-research; the latter, individual research. It is with a branch of the former, with special reference to ore-treatment, that the present paper deals. In smelting an ore by a well-established process, the result is shown by analyzing the products to see whether their compositions correspond to those calculated in making up the charge; by taking account of stock to show the distribution of metal in the different products made and the losses from dust and volatilization; by casting a thermal balance to find the distribution and losses of heat; and by making a cost-sheet to ascertain, as far as possible, the necessary outlay of money. In lixiviation and amalgamation, the mode of operating has to be varied to adapt a process to the individual ore. Here a number of tests become necessary. Each will consist of a series of experiments with one variable, in order to find the conditions under which the variable gives the best result; a summary of several tests will give the best method of operating. Working a number of charges with the best method will furnish the data desired for ascertaining the recovery of metal,

Jan 1, 1910

By T. B. Counselman

AFTER several years study, the Universal Atlas Cement Co. decided to rebuild its plant at Leeds, Alabama. The entire old plant, which was to operate during the new construction, was then to be scrapped with the exception of two kilns. The quarry was to be mechanized, new and larger kilns installed, with the most modern type of equipment all through the plant. Raw grinding operations at all of the Universal Atlas plants were dry. However, the dust hazard of this operation and the growing emphasis on occupational diseases made wet grinding attractive. Coal at Leeds is cheap, so that a slightly higher coal practice was unimportant. Power was cheap, so that waste-heat boilers were not desirable. Since new kilns were to be installed, these could be made long enough to make filters unnecessary. Wet raw grinding could be either the old practice of open-circuit compartment mills or closed-circuit grinding in accordance with metallurgical practice. The latter saved power and steel wear and saved initial investment. This had been demonstrated in cement plants. Also, the elimination of tramp oversize was a most important advantage. Ease of chemical control was another factor. Blending in the thickener, with elimination of slurry mixers had been found practicable. Therefore, if wet raw grinding were used at all, the advantages were clearly in favor of closed-circuit grinding. Detailed layouts of the most modern possible closed-circuit dry-grinding plant and of a closed-circuit wet-grinding plant were prepared, and careful estimates were made of initial investment and operating costs. Full consideration of all the factors involved resulted in a decision to install wet closed-circuit grinding. The capacity of the new kilns was established at 4000 bbl. per day. Two new kilns were installed, each with a capacity of 80 bbl. per hour. Since 625 lb. of raw material is required to make a barrel of finished cement, the capacity of the grinding plant for the new kilns had to average only 1250 tons per day. Sufficient additional grinding capacity had to be provided for the two remaining old kilns, or their possible replacement by a third new kiln. The grinding rate, therefore, was set at 90 tons per

Jan 1, 1939

By R. E. Ford, P. Tarassoff, P. H. Jennings

Copper oxide ore may be leached at all sizes from run-of-mine down to pulp, and consideration must be given to all available methods in determining the most economical one. Heap leaching was evaluated in a pilot plant at Gaspe Copper Mines, Ltd. which was designed to simultaneously leach two 1200-ton dumps of ore. The plant was operated for two years, in part under severe winter conditions. Two modes of leaching were investigated: acid leaching in which sulfuric acid was added externally to the leach solution, and pyritic leaching in which pyrite concentrate was added to the dump and acid was generated in situ by bacterial action. The pilot plant operation is described, and the results are compared with laboratory data obtained in 6-in.-diam columns. It is concluded that pyritic leaching offers certain operating advantages over acid leaching when copper is recovered by cementation in that iron buildup in the solution is prevented.

Jan 1, 1974

By H. A. Kortmann, K. Koch, B. M. Grover, O. P. Burghardt

Addition of lime, especially when treating a hematite feed, sometimes results in swelling and a severe loss in strength during reduction in the temperature range 900° to 1100°C and in grain disintegration in the temperature range 400° to 600°C in a weakly reducing atmosphere. Swelling and/or grain disintegration of pellets is often the reason for trouble in blast furnace operation, resulting in a decrease in the rate of smelting. Following a brief description of the test procedures employed (measurements of swelling, pressure-reduction-softening and grain disintegration), some results are given which were arrived at when testing pellets from industrial plants. Results of systematic tests are presented, where the effect of the quantity and quality of the gangue upon the behavior during reduction of pellets is illustrated. Varying amounts of quartz and limestone were added to a high-grade hematite ore and, then, pellets produced in a pot grate. The relationships of the behavior of the fired pellets during reduction are presented, among others, in the ternary system CaO-FeOn-SiOP. Finally, an attempt is made to explain the reasons for swelling, loss in strength, and grain disintegration.

Jan 1, 1974

By W. A. Goodyear

It is safe to assert that in cities generally, the fuel of the future for all domestic, as well as for most manufacturing and metallurgical purposes, will be gaseous fuel. The immense advantages which gas possesses in facility and cheapness of distribution, cleanliness, and economy of manipulation, and the facilities which it offers for utilizing in almost all cases a much higher percentage of the total quantity of heat produced, than it is possible to do with any kind of solid fuel, are facts which will vastly more than compensate for the comparatively small loss of heating power, which will be found necessary in the turning of the solid fuel into gas upon a large scale, and which, in the bpinion of the writer, will, at no distant day, command attention, and will ultimately result in a revolution in our use of fuel. The employment of gaseous fuel upon a scale of any considerable magnitude, has hitherto been almost entirely confined to the utilization of the waste gases of the iron smelting furnace for heating the blast, and the rapidly increasing use, for certain metallurgical pur-

Jan 1, 1883

By G. Kimmel, A. Bar-Or

The rate of nucleation and the rates of both lateral and longitudinal growth of martensite plates (needles) in b—a transformation were determined as a function of temperature, in various U-Cr alloys. The activation energies for nucleation and both modes of growth were calculated from the experimental results. The identical values for lateral and longitudinal growth clearly indicate that both are controlled by the WHITE,' Mott and Hines and Holdeen3 showed that characteristic martensite plates (needles) appear in U-Cr alloys during the transformation 8 —0 in the lower temperature range (up to -300°C). Holden pointed out that the rate of growth of the individual martensite plates under isothermal conditions is same mechanism. Lomer's suggestion that single-atom movement over subatomic distances controls the specially slow growth of martensite receives further support from the present kinetic study, which shows that the growth rate can be described quantitatively by known formulas for the growth rate in processes involving single-atom movement. very slow, and suggested that this is due to the slowness of the relief of the stresses engendered during the growth of the individual plates. lomer4 attributed the slow growth to the complexity of the atomic adjustment at the growing interface b/(u. In the present work the rates of nucleation and growth of martensite plates in U-Cr alloys were studied by direct observation, in order to elucidate the mechanism which controls their characteristic slow growth.

Jan 1, 1968

By F. B. Foley

IT is with an unusual degree of personal satisfaction that I find myself in a position to pay tribute to the memory of Henry Marion Howe. One could not have spent any length of time in the presence of Dr. Howe without profiting intellectually. I do not hesitate to say that my years of association with him were the most stimulating of all my years of metallurgical study. He always impressed one with his own eager search for knowledge. Never dependent on the written word alone he sought information from anyone whose opinion he valued. His ability to piece together bits of apparently conflicting data from various sources so as to build up a logical hypothesis was unique. A small slight man with the intellect of genius he would have gone to the top in any endeavor he undertook and it was fortunate for metallurgy that its study attracted him as it did. Howe was a modest man. I like to recall an incident which left a lasting impression with me. The lab- oratory in his home, "Green Peace," was in the basement and access was by way of stairs leading down from his secretary's room. In using these stairs my attention was attracted many times to an ordinary cardboard shoe box which reposed on the shelf above the landing. It was crudely labeled on its side in black ink "Vanity Box." My curiosity was aroused to the point that I finally asked his secretary what it was. With some amusement she took the box from its shelf on the stairway, opened it and showed me its contents—numerous letters, from the foremost men of science of every civilized country throughout the world, commending his "Metallography of Steel and Cast Iron." I recall that in reply to one who thought there was not enough of Howe's own researches in his book he wrote, "Primarily I am a writer, secondarily an investigator." Howe wrote to make his readers think. No one ever strove harder than he to be right but above all, whether his viewpoint proved ultimately to be right or wrong, he was always content if by his stand, he provoked a reader to take the next step along the path to greater knowledge. I doubt that he was ever afraid to be wrong for he was always secure in the thought that his effort was guided by a sincere search for the truth. One continually searching for truth is entitled to occasional excursions up the wrong alley. A glance backward to the metallurgical confusion of some thirty to forty years ago, or need one go back so far, provides convincing proof of what a host of companions one may have in a common acceptance of ideas which the future will prove to be wholly untenable. Well over a hundred years have passed since investigators have interested themselves in the effect of increasing the temperature of iron and steel on their mechanical properties. We are told by Charles Walrandl in "Industrial Annals" for June 11, 1822, that bend tests, conducted in a Russian steel works of Prince Demidoff, on steel bars "highly heated" and bent during cooling became brittle when bent at an iris blue color. He concluded, "That when steel is heated to a temperature between 473°F and 662°F the mettle was more brittle between these limits than at a much lower or at a much higher temperature." It was a curious bit of information recognized as true to this day and still not explained satisfactorily. In 1878 Charles Houston in Annales de Mines associated this brittleness with an increase in tensile strength at 572°F. When this relatively low temperature is exceeded it is recognized that steel becomes weaker as temperature is increased up to the melting point, where no strength of practical importance remains. It is easy to believe, in fact it goes without saying, that this weakening as the temperature of a metal is increased is the result of the motion of the atoms making up the metal, a motion which itself is evidence of the temperature increase. However, if we are considering iron or steel we find that this decrease in strength is not a steady one, for, besides the increase in strength just referred to, one comes to a temperature, the critical temperature, where results of tests indicate the metal to be extremely weak and then as temperature increases to become sensibly stronger again. This apparent anomaly was made the subject of the first Howe Memorial Lecture, delivered by Albert Sauveur in 1924. It may be of interest to review these findings of Sauveur. He used two methods of investigation. One involved the twisting of bars. The bars were heated in an

Jan 1, 1951

By B. Barlin

Introduction The development of metallurgical practice at lambia Broken Hill is directly related to the change in mineralization of the deposits as mining progressed from the open pits to underground. The ore consists of a mixture of lead and zinc sulphide minerals, together with abundant silicates, carbonates and other oxidized minerals of these metals. The irregularity that characterizes the shape of the orebodies applies equally to their mineral content, which makes ore reserve calculations and the maintenance of a balanced feed to the metallurgical plants, problems of some magnitude. History The Rhodesia Broken Hill Development ,Company was formed in 1904 after an Australian prospector, T. G. Davey, discovered the outcrops in 1902. In the early years zinc ores were calcined for shipment but this proved uneconomic. Cerussite outcrops were then smelted directly in blast furnaces for the production of lead until 1929 when ore above the water level was exhausted.

Jan 1, 1970

By Thomas. B. D.

GRAVITY concentration is a general term designating processes for separating and sorting granular material by means of forces that depend on the density, size and shape of the particles. When these forces are applied to the particles the latter are caused to move, those of a given density along one path and those of a different density along another, until ultimately they are sufficiently separated to be removed from the operation of the process. The forces producing this separation are in general complex and, unfortunately, no completely rigorous analysis of them has as yet been devised. The science of the hydrodynamics of viscous fluids deals with , the little that is known about the problem. Every observer of nature is familiar with the fact that an object moving in a fluid encounters a force of resistance. We have only to walk against a brisk wind or stir a cup of coffee, or observe the slow fall of a grain of sand in water, to experience directly the fact that such forces exist. The exchange of force between an object and a fluid in which it is moving operates on the fluid as well as on the object. Thus a sailboat may be set in motion by the force exerted by the wind on the sail; but the sail also deflects the wind-furthermore, the water in which the boat floats is set in motion by the force exerted by the boat as it cleaves through the water, The wind is thus enabled to do work on the water through the intermediary of the boat. In general, an object moving through a fluid encounters a force that opposes the motion and also acts to change the motion of the fluid. In gravity concentration we are dealing with this force of resistance acting on the granular particles that are to be separated. Furthermore, the motion induced in the fluid by a particle will in turn affect the motion of a neighboring particle. This effect will be reciprocated and in consequence there will be an exchange of forces between all the particles in the material. These effects are complex and the most that can be expected is that we may be able to determine in a qualitative way how they operate. In gravity concentration, then, the following types of forces may be distinguished as acting on the particles:

Jan 1, 1943

By William Ward

ONE often reads of the rich placer gravels in many of the canoe-traveled rivers of South America. The apparent richness of these gold-bearing gravels impresses the traveler, and in fact he may see batea after batea showing enough colors to figure over a dollar per cubic yard. These workings are called "playas" from the Spanish word playa, meaning shore or beach. Many workings have been reported in tropical rivers, but to my knowledge no dredge has made a success in such deposits. Investigation generally shows that the area of richness is limited and especially that the depth of the rich concentration is hardly ever more than a few inches. The Cauca river in Colombia, South America, is noted for its many rich playas.. This river rises near Popayan in the southern part of Colombia, flows north through a narrow valley between parallel mountain ranges and empties into the Magdalena river near Maganque. The airline distance between source and mouth of this river is only about 500 miles. The rainfall is large and the lower Cauca appears to be about the size of the Missouri river in the United States. From its mouth up to Valdivia, in the State of Antioqua, it is navigable. Above Valdivia is a. narrow gorge, above which the river is again navigable for some distance. The part of the Cauca where the playa panning is most noticeable is from Valdivia down to Where the Nechi river enters the Cauca, a distance along the river of about 100 miles. The current in this part is swift, so that the stern-wheel river steamers make the trip with some difficulty. In the course of my work in this section of Colombia I have had the opportunity to make a study of several of these playa workings and will give in detail the conditions observed.

Jan 7, 1914

By Leonard E. Wood, Yeghishe M. Avedissian

Knowledge of the basic properties of rocks-strength, structure, and permeability-is prerequisite for the success of foundation work for masonry dams, large bridge piers, and tunneling as well as for excavation in rock and special underground construction. Strength of engineering materials depends upon texture and structure as well as the environmental conditions to which they have been subjected. Failure in its widest sense implies the transition of a material from elastic to plastic state (yield strength), from continuous to discontinuous state (rupture strength). The compressive strength of a material such as rock is the stress at which a sample, loaded and unconfined at the sides, fails by rupture. Some of the external factors that control strength of rocks are the nature and type of stress, whether uniaxial or triaxial, compression, tension, or torsion. Another important factor is the rate of stressing-whether constant, impact, or gradually increasing. Of the internal factors, the effect of texture upon strength is obvious. Generally, fine-grained rocks have higher compressive strength than coarse-grained prototypes. Among metamorphic and igneous rocks those with better and higher degree of interlocking of their crystals are generally stronger than the ones with poor or lower degree of interlocking. In sedimentary rocks, the degree and type of cementation has a great influence upon their strength. Structurally, the existence of fissures, cracks, and seams of argillaceous or organic materials in a rock specimen will greatly reduce its strength. Because most rocks are characterized by bedding planes, laminations, or foliations, they are anisotropic in their physical properties and hence compressive strength depends on the orientation of the bedding planes to

Jan 1, 1972

By Hugh D. Pallister, Richard W. Smith

The Alabama flake-graphite industry has flourished only in times of war when importations of foreign graphite for crucible use have been greatly curtailed or cut off. World War I was a boom period and in 1918 some 30 plants produced 7,795,475 lb. of flake graphite. The industry languished following the war and no graphite was produced from 1929 to 1939. The Federal Bureau of Mines began investigating the Alabama graphite deposits in 1940 and worked out modern recovery methods that were applied to production during part of World War II. A prospecting program disclosed reserves of over 25 million tons of graphitic schists. In 1942 the War Production Board authorized the enlargement of the only plant then producing flake graphite and the construction of two new plants. Production of flake graphite from these three plants in 1943 is estimated at 8,100,000 lb. Increased imports from Madagascar late in 1943 shut down one of the new plants and curtailed production at the other. Alabama flake graphite has not yet been able to compete with Madagascar graphite for use in the manufacture of any but small graphite crucibles. The future of the industry must depend on meeting the higher carbon content demanded for other uses.

Jan 1, 1945