Search Documents

By C. P. McCormack

The Cuyuna manganiferous iron ores can be a principal source of manganese for the iron and steel industry in the United States, provided metallurgical methods as a whole are adjusted so as to use run-of-mine ore. The use of manganese in steelmaking is growing. Increasing amounts of impurities in raw materials call for more manganese, a constant cheap supply of which is wanted. There are few deposits of ore in the United States carrying over 35 per cent. manganese that can be mined and marketed at a profit in normal times. We are largely dependent on foreign ores. The small domestic deposits should rightly be held in reserve for an emergency, such as a war, when importation might cease. Even the production from lean ores, concentrated it may be, might not carry us through a protracted stringency. The Cuyuna district is, therefore, during normal times capable of supplying a large total of manganese. The ores are iron ores containing 5 to 25 per cent. of manganese with the inverse range of 52 to 28 per cent, of iron. The manganese costs no more per unit in the ore than the iron, because cost of mining, largely by open-pit methods, is not affected by the manganese content. The manganese units should, perhaps, command a higher price, but as their value is contingent on metallurgical practice, a higher price may be justified only when a shortage in manganese occurs. Manganiferous iron ores can never entirely supplant straight manganese ores though methods are employed that will permit them to do so partly. For the manufacture of ferromanganese, ores carrying above 42 per cent. manganese are needed. Ores with manganese running between 20 and 42 per cent. are used for making spiegeleisen. But established practice in certain plants, based on the admixture of manganiferous iron ores to straight iron ores has greatly lessened the consumption of high-priced, scarce, manganese alloys with good results. The substitution of manganiferous ores for ferro and spiegel affects the manufacture of basic iron and its conversion into basic open-hearth

Jan 1, 1925

By C. Richard Tinsley

Non-ferrous econometric metal models available from consultants are reviewed for structure and computer access, using copper as an example The evolution of a computerized metals price forecasting system for a consumer of non-ferrous metals is outlined including front ends, bridge equations, and supporting databases. An empirical sensitivity analysis technique is described. A postscript discusses the subscription costs of these models.

Jan 1, 1977

By J. A. Marton, N. Brown, M. Herman

AT high temperatures a deformed polycrystalline metal shows grain-boundary displacement in preference to slip lines.' This has led to the conclusion that overall strain at high temperatures is produced chiefly by grain-boundary displacement. Detailed microscopic examinations of individual grain boundaries have shown many interesting ways by which their displacement occurs; sometimes no grain deformation was observed except possibly in the immediate neighborhood of the boundary. However, X-ray examinations show that at high temperatures subgrain formation occurs;Y he process, generally called polygonization, results from lattice bending and the subsequent climb of dislocations to form low-angle boundaries. Quantitative measures of the grain-boundary displacements show that they make a minor geometrical contribution to the overall strain; the major contribution is made by grain deformation."'" A relationship between grain-boundary displacement and grain deformation was suggested by McLean, who showed how the degree of polygonization would determine the amount of grain boundary displacement: and by Dorn, who showed that for a given creep stress, the amount of grain-boundary shear was related to the overall strain and was independent of temperature.' Although the grain-boundary displacement may make a small geometrical contribution to overall strain, it may still be the rate-controlling factor in high-temperature creep. If in general grain-boundary displacement and grain deformation are dependent quantities, then the designer of a creep-resistant metal would like to know whether it is more desirable to strengthen the matrix of the grain or to increase the strength of its boundary. The widespread interest in the relationship between temperature and grain-boundary displacement makes it desirable to test the generality of Dorn's result6 that the ratio of grain-boundary displacement to overall strain is independent of the temperature for a given creep stress. In this investigation p-brass was used because it produces sharp grain-boundary displacements above 400°C. Since B-brass undergoes an order-disorder transformation which abruptly strengthens the grain, it is an excellent metal for determining whether grain-boundary displacement or grain deformation is the rate-controlling factor in creep. The problem will be confined to the temperature range where

Jan 1, 1958

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit, the selection of the proper material and size of sucker rods, and the design of the pumping unit, requires that the sucker-rod loads be known with a reasonable degree of accuracy. In production practice, it is also desirable to know the effects of operating speeds and strokes on a plunger motion, as well as on the rod loads. For a particular well, data on rod loads can be obtained by measuring the load in sucker rods with a dynamometer. This method is not satisfactory because it does not permit the various factors to be investigated independently. It is also impossible to measure the plunger motion simultancously with rod motion under operating conditions. The mathematical solution is impractical because of the simplifications that have to be made to get a solution and the tremendous amount of numerical work that is necessary after such a simplified solution has been attained. This paper shows how analogies and models can be applied to the solution of these problems. The loads set up in a sucker-rod string during the ordinary pumping cycle are made up of the weight of the rods, force required to accelerate the rods, weight of the oil and force required to accelerate the oil on the upstroke, rod friction, stuffing-box friction, plunger friction, friction of the oil in the tubing and rods, arid friction loss through the valves. The problem of determining the sucker-rod load is further complicated by the fact that the long oil column and the sucker-rod column act as springs, which affect the transmission of the polished-rod motion. A further complication is the fact that the motion cannot be transmitted at a speed greater than that of the velocity of sound in the material, and this means that there will be a time lag in the transmission in the motion, as well as a modification of its magnitude and a phase displacement.

Jan 1, 1936

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit, the selection of the proper material and size of sucker rods, and the design of the pumping unit, requires that the sucker-rod loads be known with a reasonable degree of accuracy. In production practice, it is also desirable to know the effects of operating speeds and strokes on a plunger motion, as well as on the rod loads. For a particular well, data on rod loads can be obtained by measuring the load in sucker rods with a dynamometer. This method is not satisfactory because it does not permit the various factors to be investigated independently. It is also impossible to measure the plunger motion simultancously with rod motion under operating conditions. The mathematical solution is impractical because of the simplifications that have to be made to get a solution and the tremendous amount of numerical work that is necessary after such a simplified solution has been attained. This paper shows how analogies and models can be applied to the solution of these problems. The loads set up in a sucker-rod string during the ordinary pumping cycle are made up of the weight of the rods, force required to accelerate the rods, weight of the oil and force required to accelerate the oil on the upstroke, rod friction, stuffing-box friction, plunger friction, friction of the oil in the tubing and rods, arid friction loss through the valves. The problem of determining the sucker-rod load is further complicated by the fact that the long oil column and the sucker-rod column act as springs, which affect the transmission of the polished-rod motion. A further complication is the fact that the motion cannot be transmitted at a speed greater than that of the velocity of sound in the material, and this means that there will be a time lag in the transmission in the motion, as well as a modification of its magnitude and a phase displacement.

Jan 1, 1936

By Joseph R. Crump, Francois Ville, Frank M. Tiller

Several simplifications have been accepted in filtration theory during the past fifty years in an effort to avoid apparently intractable mathematical problems. In effect, these simplifications ignored the variation in average cake porosity and average filtration resistance with variation in pressure drop or with time. This study examines the traditional approach and shows that, in many cases, it cannot give correct design guidance. Using a set of dimensionless parameters because of the large number of significant variables, a revised theory is developed which does not require that porosity and resistance values be set constant. Graphs developed in the traditional approach (e.g., dt/dv versus v or t/v versus V) have substantial curvature near the ordinate; but this curvature is frequently ignored in theory and is easily missed in experiments. The revised theory allows more accurate design calculations, especially for compressible cakes.

Jan 1, 1980

By H. Landsberg

SUBSIDENCE caused by mining operations has been a matter of interest for the mining engineer for just 111 years, since the Belgian Committee for study of subsidence in the city of Liege submitted its first report in 1825. This interest is fairly expressed in the enormous amount of literature that has since appeared on this subject. A bibliography, probably far from being complete, which preceded this study as a pre-liminary survey, comprises more than 800 titles. In spite of this fact the problem remains today as acute as it has ever been. The questions of as good a recovery as possible of the national resources, the safety of the operations, and the protection of private and public property are the important angles from which to look at the problem.

Jan 1, 1936

By D. M. Hausen

The amenability of a given vanadium ore to any given treatment depends largely on the mineralogic combinations of vanadium in the ore. Quantitative data on vanadium mineralogy provide not only an objective basis for selection of proper treatment, but also may eliminate many time-consuming amenability studies whose results are empirical, at best. Vanadium is distributed through the interstices of mineralized sandstone ores in the form of oxidized vanadates, reduced oxides, and silicates. Oxidized vanadates, e.g., carnotite, tyuyamunite, etc., are most readily beneficiated by simple acid leaching. Reduced oxides are more slowly solubilized, but relatively amenable to most acid treatments. The layered silicates, roscoelite, mixed layered mica-montmorillonite, and chlorite, are least amenable to most acid extractions, and constitute an assemblage of vanadium- bearing clays that are common to many sedimentary deposits. Vanadium is combined principally as layered silicates in the clay fractions of many sandstone ores. Mineralogic studies in this paper are largely confined to clay minerals, and to their amenability characteristics in low pH liquors.

Jan 1, 1985

By Harvey S

After considerable experience in connection with the magnetic iron-ores at the South, especially in the Cranberry district of western North Carolina and eastern Tennessee, the writer was led into a thorough investigation of the magnetic separation of iron-ores, and, from this investigation, has gradually been developed a separating machine which it is the purpose of this paper to explain. Numerous United States patents have been issued upon machines for magnetic separation. Since the original patents date back to 1849, it is not possible to-day to establish broad claims upon the principles of electro-magnets as applied in such machines. Among these inventions there are certain types of separators which have very marked practical advantages over the others; and these successful machines, while varying radically from each other in their proportions and arrangements, are all based upon a principle originally explained in a patent which was granted in 1870, and which has now expired by limitation. The problem of practically separating iron-ores, as found in the mines, is very different from the separation of a purely magnetic substance from a purely non-magnetic one, since the crystals of magnetite, scattered through the ore-bearing rock, and sometimes collected in masses, are of very different sizes. The average size of the particles may be definitely ascertained for each mine, and the crushing- and screening-machinery may be adapted thereto, but there will still be a large percentage of very fine crystals which, in the crushing for the average, will not be broken apart from the gangue. If these mixed particles are thrown into the heads they carry gangue with them, and if thrown into the tails they occasion a loss of ironore. There are two methods for preventing such loss. One is, to crush all the material to the size of the finest particles, which means, of course, a large crushing-plant, heavy wear and tear, and excessive cost for repairs, and the production of only a very fine-grained concentrate which our blast-furnace managers, to say the least, do not

Jan 1, 1893

By E. S. Bardwell

THE reverberatory copper-refining furnaces at the Great Falls Reduction Dept. of the Anaconda Copper Mining Co. have used successively, as fuel, lump coal on grates, pulverized coal, oil and natural gas. In no other plant, so far as can be ascertained, has such a variety of fuels been used. This fact affords a unique opportunity for comparing the relative efficiency obtained with these several fuels under nearly identical conditions. FURNACES The present furnace refinery at Great Falls was placed in operation in April, 1916. The original installation consisted of two furnaces, each with hearths 36 by 14 ft. and provided with fire boxes 10 by 12 ft. for firing lump coal on grates. These furnaces had air-cooled sand bottoms and chrome-brick side walls both above and below the metal line. The roofs were of 12-in. silica brick. Each furnace was provided with a waste-heat boiler of approximately 400 boiler-hp. capacity. We soon found that chrome brick was very unsatisfactory as sidewall material because of its excessive spalling. At the first opportunity the furnaces were rebuilt, using magnesite brick below the metal line and silica brick from the metal line to the roof. At the same time the thickness of the side walls was increased, thus decreasing the width of the hearth to 13 ft. At about this time also, the thickness of the furnace roofs was increased from 12 to 15 in. No further changes occurred in furnace design until 1922, when the use of lump coal on grates was abandoned in favor of pulverized coal.

Jan 1, 1932

By John Dresser

General THE controlling supply of asbestos for the world is obtained from southern Quebec, 150 miles or less north of the international boundary line between Canada and the United States, and about 75 miles south of the city of Quebec. The principal production is furnished by eight mines, seven of which occur within a distance of 6 miles, but there are also several smaller properties in the vicinity. The industry was begun in a small way some 35 years ago and has advanced more or less regularly ever since. The annual production now exceeds 100,000 tons and its value is about $3,000,000. It represents over 80 per cent. of the world's production. History Asbestos has been known in the eastern townships of Quebec since 1847, when attention was called to it in an official report by Sir William Logan, the first Director of the Geological Survey of Canada, but it was not until 30 years later that it came into commercial importance. The largest deposits, those of Thetford and Black Lake, were found in 1877 during the construction of the Quebec Central Railway. Work was begun upon them almost at once and has been continued ever since. The Danville mine, the next largest producer, was opened in 1879, and the slip-fiber deposits of East Broughton were located shortly afterward. For the first 15 years only the "crude" asbestos was recovered; that is, fiber long enough to be extracted by hand cobbing. Although this is still a valuable part of the production, it is now a relatively small part of the total output.

Jan 9, 1914

By D. T. Farnham

The shale used at the Renton plant of the Denny-Renton Clay and Coal Co. for the manufacture of vitrified paving brick occurs in a hill rising from 200 to 300 ft. above the level of the valley in which the plant is situated.

Jan 1, 1915

By Raymond Ladoo

THE milling of talc, as is the case of many non-metallic minerals, until recently, has not received adequate technical consideration, for the talc industry has become of importance only within the last decade. At first, talc was used only in the massive form, for foot warmers, griddles, and so on, and milling methods were unnecessary. As the demand for ground talc increased, producers adopted the machinery used in the milling of flour; in fact, many talc mills were rebuilt flour mills. Improvement has been slow, but today several types of grinding and separating machinery are in use; many of them, however, are still inadequate and inefficient. To determine the best methods of milling talc, it is necessary to understand the essential properties a talc must possess to fit it for a particular use. For toilet purposes, whiteness, freedom from lime and grit, fineness of grain, and good "slip" are essential. As a paper filler or coating, the talc must be white, have a good slip, be free from grit and iron, uniform, and fine grained; freedom from lime is a disputed point. Fibrous talc is supposed to be superior to massive on account of the interlocking of grains in the paper, thus increasing its strength; this point, though, is in doubt. In general, talc for the paper industry need not be of as high quality or as fine grained as that used for toilet purposes. Talc is usually bought by sample, for which reason it is difficult to state the essential properties for use in paint, rubber, roofing, and so on. The adoption of standard screen tests and standard grades by producers is necessary before an accurate basis for manufacturing or selling standards can be established. Off-color tales might be utilized, as in Germany and-Austria, by the establishment of standard grades of colored tales.

Jan 1, 1921

By John M. Bostwick

Bitumen is a general term for a group of materials composed of mixtures of hydrocarbons that are fusible and soluble in carbon disulfide. Included in the group are petroleum, asphalts, asphaltites, and mineral waxes. Asphalt is a dark-colored, cementitious solid or semisolid, which generally softens on heating and resumes a more viscous or solid state when cooled (personal communication). It is found in native form in fissures and pore spaces in rocks and as lakes. It is also obtained from the residues produced in petroleum refining. Asphaltites are black, naturally occurring solid bitumens. They are generally shiny and break with a conchoidal fracture. Common asphaltites are gilsonite (uintahite), grahamite, and glance pitch. Mineral waxes are solid or semisolid, relatively nonvolatile bitumens of various colors, having an unctuous feel and waxy luster. Of the native waxes, ozokerite is the best known. Montan wax is also classed as a natural wax, although it never occurs in the pure state and must be extracted from lignite or cannel coal (Ladoo, 1920). Mineral waxes may also be obtained by pyroprocessing of petroleum, lignite, and peat. Pyrobitumens are dark-colored, solid hydro- carbons that are infusible and relatively insoluble in carbon disulfide. They are so-called because they will yield liquid and gaseous hydrocarbons only when heated. Asphaltic pyrobitumens are defined as "substantially free of oxygenated bodies" and include wurtzilite (elaterite), albertite, and impsonite (Thrush, 1968). Nonasphaltic pyrobitumens contain oxygenated bodies; examples are coal and peat. The nonasphaltic type will not be discussed further. Petroleum Asphalts Asphalts refined from crude petroleum have almost completely replaced the native types. Refineries can produce asphalts in every desirable grade more economically and in greater quantity than the native types and with a variety of properties that meet the requirements of the various manufacturers using them. For all practical purposes, it is estimated that more than 95% of the asphalts consumed in the United States are refined from crude petroleum (private communication).

Jan 1, 1975

By A. M. Talbot

THERE is still considerable controversy as to the exact nature of the mechanism of the age-hardening process, in spite of the many experi-ments already performed. For this reason, a considerable number of typical systems should be examined in detail and their results correlated. Furthermore, the methods of studying the changes that take place during the progress of this phenomenon should be carefully scrutinized and the different methods applied to the same samples, preferably at the same time. The experiments described in this paper are presented to supply information on one age-hardening system and to show how the various methods of investigation compare in their indication of what has hap-pened. In brief, the progress of aging in magnesium alloys containing about 10 per cent by weight of aluminum at different temperatures was followed by measurements of hardness, electrical resistivity, dilation and lattice parameter, and by microscopic observation.

Jan 1, 1936

By G. H. Jardine

In future years, decision makers in the coal industry will make more and more decisions based on information from computer-based models. Whilst the use of such techniques will provide many advantages for coal companies, particularly in terms of efficient utilisation of their human resources, it is equally important for the decision makers to have an awareness of the limitations inherent in each particular computer-based model being used to provide information for the decision making process. A recommended procedure for identifying such limitations - by analysing the 3 major elements of the model - is presented. The human aspects of increased use of computer-based techniques are emphasised throughout the paper.

Jan 1, 1983

By John E. Sweet

There have already been so many subjects of a purely mechanical nature presented to the Institute of Mining Engineers, that it is unnecessary for me to apologize for adding another to the list. When a new invention, or what is supposed to be a new invention, claiming simply an improvement on the well-known devices, is to be described, it is usual to point out the defects of the old and give a history of the object or the art up to date. But, as no doubt a large proportion of the members of this Institute know as much, or more, about the history and use of the steam-engine indicator than I do myself, I will not further preface the subject, than to remind you that what called for the Richards's improvement on the Watt's indicator was high speed; that the leading improvement was the reduction of momentum in the reciprocating parts; and that this was accomplished by making the parts lighter, and reducing the travel of the heaviest, of them, and consequently the speed and momentum. The use of the indicator has been extended, for the speed of steamengines and other prime movers has been increased, until one engineer at least, John Cooper, of Philadelphia, says, "I want an indicator that will work up to a thousand revolutions." .Mr. Thompson, of the Buckeye Steam-Engine Company, of Salem, Ohio, has improved on the Richards's indicator by another reduction in the momentum, which is done by putting the parallel motion nearer the fulcrum of the pencil arm, reducing both weight and travel. The characteristic feature of the indicator I am going to illustrate is a still further reduction in the same direction, which is accomplished by dispensing with the parallel motion altogether. As is often the. case, in putting a simple idea into shape, some difficulties

Jan 1, 1879

By Alexander Coucoulas

FABRICATION of thin-film circuits deposited on glass substrates requires the formation of permanent electrical contacts. Since thin films are in the order of a few thousand angstroms thick and are deposited on nonconductive surfaces such as glass, new methods of lead attachment are being pursued in the microelectronics industry. Ultrasonic welding is being considered in thin-film technology since joining can be accomplished between a wide variety of dissimilar materials.l,' Ultrasonic welding is accomplished by a transducer-coupling-tip system which converts high-frequency electrical energy into mechanical vibrations and delivers it into the weld region. During the process the tip oscillates in a direction parallel to the surface of the weldments, inducing shear stresses in the work pieces which are clamped between the tip and anvil. Though the basic bonding mechanism is not clearly understood, it has been described as closely akin to friction welding. In the course of an investigation concerned with ultrasonic we!ding of aluminum wires to tantalum thin films (1400A) deposited on glass, low weld strengths were related to glass failure. Upon investigating this condition, an improved method of bonding was developed where the aluminum was held at a temperature where a minimum amount of strain hardening occurred during the introduction of ultrasonic energy. Experimental Procedure. Aluminum wires (0.015 in,) were bonded to tantalum thin films with an optimized set of welding parameters (power, time, clamping force) employing a commercial 100-w 60-kc ultrasonic welder. Forty-five degree shear-peel tests, where the lead is pulled at a 45-deg angle with respect to the substrate at 0.2 in. per min, produced a large variation from zero to the strength of the wire, Table I. Inspection of the weld region generally revealed: glass cracking before and after testing; the removal of glass nuggets from the substrate by the lead during testing, Table I; thin-film penetration. In an effort to improve the shear-peel strength, the aluminum between the tip and substrate was heated above ambient temperature through an argon gas media prior to and during welding with the same parameters employed above. With the addition of heat: wire deformation was increased; shear-peel tests all failed at the weld-wire junction, leaving the bonded portion undisturbed; no evidence of glass cracking or film penetration prior to or after testing was observed. In order to prevent failure at the weld-wire junction due to excessive wire deformation, 0.035-in. aluminum wires were welded to tantalum thin films with an optimized set of welding and heating parameters. As

Jan 1, 1967

By E. Goldin, H. J. Juretschke

THE electrical properties of porous conductors have been studied ever since such materials, usually prepared by pressing and sintering of metallic powders, obtained practical importance. In most cases, however, the results have not been easy to interpret because of the great number of independent variables such as powder size, pressure, pressing rate and temperature, subsequent thermal history, porosity, and so on, which enter into the fabrication of industrially desirable materials. In recent years an interpretation of these properties has become of interest because the electrical properties of many new substances, prepared as fine powders by crystallization from the vapor phase or by reactions in the solid state at high temperatures, have to be determined on porous samples formed from the powder. Since theoretically significant information must refer to the fully dense state of the material, it is important to relate the electrical properties measured on such porous samples to those expected for a sample of 100 per cent density. A simple theory for the porosity dependence of the electrical conductivity and the Hall effect was recently proposed by Juretschke, Landauer, and Swanson.' Their model, assuming a distribution of pores of equal size and shape, sufficiently far apart so that each pore is embedded in a region of uni-

Jan 1, 1959

By A. Berthet

In the past two decades, of the successive steps leading from iron ore to finished steel, the production of liquid steel and its preparation for the casting operation has probably undergone the most drastic evolution. The reason for this is the development of oxygen converters (top blown and later on bottom blown) and UHP arc furnaces which are replacing the conventional processes such as the open hearth and basic Bessemer processes. These new processes have been great advances, but it would certainly be quite hazardous to assert that the situation will remain the same for the coming decades. In fact, with the advent of continuous steelmaking a new generation of processes has now arrived. The research and development programme at IRSID on continuous an a steelmaking began ten years ago has progressed systematically in the following stages : First a comparison was made on a small pilot scale of various techniques : for example, refining in a runner by top or bottom blowing, pulverizing the metal stream by oxygen, using the mixing effect of a vortex, etc. but for various reasons these processes proved unsatisfactory and were abandoned in favour of a method using the so -called "emulsion refining".

Jan 1, 1972