Search Documents

By Winthrop P. Haynes

The symposium on production for the year 1944 includes more foreign papers than any one of the past three years, because of a partial relaxation of the censorship in many Western Hemisphere countries. The committee was not successful, however, in securing papers from Europe and the Near and Far East at this time, with the exception of Saudi Arabia and Bahrein. Where possible, these papers include summaries upon production for the missing war years, so that we shall have no permanent gap in the records. At the close of the war, we hope again to publish the usual more complete form of report for all important oil-producing countries. EXCERPTS FROM CIRCULAR TO AUTHORS In order to facilitate interpretation of the data in this chapter, we print the following excerpts from the Circular to Authors. The field is the unit in this tabulation. In cases of fields extending across State boundaries, such as Rodessa, it is suggested that each State author treat the section of the field in his State as a unit, and by a footnote indicate that the field extends into an adjacent State. Each place in the table may represent one of three possibilities; either the proper entry is determinable and can be supplied by the author, or an approximate figure can be supplied which is the author's best guess and should be entered followed by an x, or it does not apply to the particular field and the space is left blank. Contributions of great value may be made by the author in many cases where entries are not subject to precise determination. In such cases the author should use his good judgment and make the best entry possible under the circumstances. The entry of a zero is a positive declaration, and it is an important declaration where it is in order. It is thought that the nearest whole numbers are sufficiently accurate for our purposes except as to percentage of sulphur in oil. If an author desires to report any other figures to tenths, he may do so. The quantity of gas produced should include, where possible, gas sold or otherwise marketed, and gas blown into the air, burned as flares or otherwise wasted. Segregation of these figures would be interesting if the authors can make such segregation. In any event, the figures should represent as nearly as possible the total quantity of gas removed from the reservoir. . Under the columns on "Depth," the average depth to the top of the productive zones and to the bottom of the productive wells, when subtracted, should give the approximate thickness of the productive zone. For fields where this is not true because of unusually high dip or for some other reasons, it is suggested that the authors indicate in their text the approximate average thickness of the productive zone. The net thickness of the producing formation should be the thickness of the producing zone, less the estimated amount to cover the portions of the zone that do not yield oil, such as dense shales, etc. It is recognized that for some fields the authors can only make rough guesses; in such cases, they should enter their best estimate followed by an x. Average production per acre-foot need not be reported as it can

Jan 1, 1945

By Richard M. Foose

The year 1950 has been a fascinating and unusual one as far as industrial minerals are concerned because of the sudden development of a critical international situation in late June. The first half of the year was marked by thriving peacetime conditions.

Jan 2, 1951

By C. A. Hartnagel

The year 1944 marks the eightieth anniversary of the discovery of petroleum by drilling in New York State. It was in 1864 that a half dozen shallow wells were drilled at Limestone in Cattaraugus County, in a region that now forms the northern extension of the 82,000-acre Bradford pool. These early wells found oil, but not in paying quantities. They did, however, attract attention to the district and were a factor in the development of the still active Bradford pool of Pennsylvania and New York. During 1943, the production of petroleum in New York amounted to 5,029,000 bbl. This represents a decrease over the previous year, in which 5,421,000 bbl. was produced. The flush production for the New York fields occurred in the early eighties shortly after the discovery of oil in the Richburg pool of Allegany County. During the flush period, production was in excess of five million barrels annually. By 1887, however, the output had decreased to an amount only slightly more than two million barrels, and through the early years of the present century the annual total was often less than one million barrels. Flooding of the oil sands for increasing productioil was made legal in 1919, and in 1927 the output once more reached the two million mark. Two years later it had increased to over three million barrels. In Table r is shown production since 1935, in which year for the first time the output under flooding methods was in excess of four million barrels. From this table, it is evident that oil production in New 'I'ork is rather well stabilized, and since most of the oil is obtained by the flooding, or water-drive, method, with little or no prospect of discovery of new oil territory, rapid changes in yield from year to year are not to be expected. In thickness, the oil sands have a maximum of about 50 ft., and by means oi flooding may produce 10 to 12 thousand barrels an acre and proportional amounts for thinner sands. In some cases, floods have been developed in sands only 12 ft. thick. Under good flooding conditions a yield of 2000 bbl. an acre is about the lower limit at which oil can bc produced at the present price of $3.00 a barrel. The average cost for the physical development ol a lease, not including the cost ol the lease itself, is $5000 an acre. Since several months must intervene before the flood begins to act on the oil wells, and a year or more is required to bring thc wells to maximum daily production, it is evident that a considerable interval occurs before maximum returns are realized. Once a flood is developed and the wells

Jan 1, 1944

By C. A. Hartnagel

The year 1944 marks the eightieth anniversary of the discovery of petroleum by drilling in New York State. It was in 1864 that a half dozen shallow wells were drilled at Limestone in Cattaraugus County, in a region that now forms the northern extension of the 82,000-acre Bradford pool. These early wells found oil, but not in paying quantities. They did, however, attract attention to the district and were a factor in the development of the still active Bradford pool of Pennsylvania and New York. During 1943, the production of petroleum in New York amounted to 5,029,000 bbl. This represents a decrease over the previous year, in which 5,421,000 bbl. was produced. The flush production for the New York fields occurred in the early eighties shortly after the discovery of oil in the Richburg pool of Allegany County. During the flush period, production was in excess of five million barrels annually. By 1887, however, the output had decreased to an amount only slightly more than two million barrels, and through the early years of the present century the annual total was often less than one million barrels. Flooding of the oil sands for increasing productioil was made legal in 1919, and in 1927 the output once more reached the two million mark. Two years later it had increased to over three million barrels. In Table r is shown production since 1935, in which year for the first time the output under flooding methods was in excess of four million barrels. From this table, it is evident that oil production in New 'I'ork is rather well stabilized, and since most of the oil is obtained by the flooding, or water-drive, method, with little or no prospect of discovery of new oil territory, rapid changes in yield from year to year are not to be expected. In thickness, the oil sands have a maximum of about 50 ft., and by means oi flooding may produce 10 to 12 thousand barrels an acre and proportional amounts for thinner sands. In some cases, floods have been developed in sands only 12 ft. thick. Under good flooding conditions a yield of 2000 bbl. an acre is about the lower limit at which oil can bc produced at the present price of $3.00 a barrel. The average cost for the physical development ol a lease, not including the cost ol the lease itself, is $5000 an acre. Since several months must intervene before the flood begins to act on the oil wells, and a year or more is required to bring thc wells to maximum daily production, it is evident that a considerable interval occurs before maximum returns are realized. Once a flood is developed and the wells

Jan 1, 1944

Discussion of the paper of R. H. RICHARDS and BOYD DUDLEY, JR., presented at the New York meeting, February, 1915, and printed in Bulletin No. 97, January, 191.5, pp. 67 to 72. R. H. RICHARDS, Boston, Mass.-I believe that the manner of working for efficiency in almost all lines is to study the conditions of highest efficiency, and then to measure what is being clone. We can then see how near we have approached the highest efficiency. Spigots in practice often use many times the water theoretically needed. There are places where that is necessary for safety reasons. There are, however, places where it is unnecessary, and in these places it seems to me that this work of Mr. Dudley's will be a great help to the mill man to arrive at the greatest economy of water and highest efficiency. ALBERT R. LEDOUX, New York, N. Y.-A good many years ago I received a telegram from that distinguished engineer, Hamilton Smith, which simply said in substance: "I have discovered that liquids will flow faster from a square orifice than from a round orifice of the same area, under the same head." I wondered why he sent me the telegram, but some time afterward he told me that he had been making experiments along that line in Montana; that he thought the discovery was interesting

Jan 5, 1915

By Peter Joraleman

Man has always felt more comfortable breaking his life into categories or classifications. An otherwise bewildering life somehow becomes easier to bear when divided into neat measurable sections, each of which is fitted into its proper niche. It seems likely that the world's first economic geologist, when faced with the world's first two ore bodies, started his career by classifying them. Early on, he divided his ore bodies into those born of water, of fire, and of air. In retrospect this threefold classification was probably about as useful as the more complex ones that followed. This division of ore bodies probably did not help him in his search for new deposits, but it made him feel more secure in dealing with those already known.

Jan 12, 1975

By Edward Halse

Normal banded structure,* exhibiting bands or layers of mineral symmetrically arranged from the sides to the center of the vein, appears to be by no means common in the Republic of Mexico. When the bands of quartz form interlocking crystals in the center (" comb-structure "), the evidence that the filling has taken place in an open space is complete. This also applies in the case of any mineral the fibers of which are perpendicular to the walls, and which presents here and there, in a central line, cavities or vugs lined with crystals (geodes); but it does not follow that the whole width of the banded vein represents that of the original open fissure. The opening and filling may have been slow and gradual processes, advancing

Jan 1, 1902

Jan 1, 1923

Jan 1, 1923

INTRODUCTION Engineering studies of many near surface coal deposits that are amenable to strip mining can be enhanced and expedited by the application of computer techniques for defining coal reserves and overburden and intraburden yardage and their stripping ratios. The case study discussed herein could be from the western coalfields of Colorado, Wyoming, or Montana; the lignite deposits of the Dakotas or Texas, or from the strippable coal seams of the midwest. Because the techniques can be applied so universally, the actual map locations are not identified. The same computing principles apply to one seam or multiseam deposits, and the capability of the computing programs and plotting routines to display the coal seams in plan and sections provide excellent base maps for further engineering planning and mine layout studies. MANAGEMENT OF DRILL HOLE DATA Drilling for coalfield information is usually done at much wider centers than for other mineral deposits. The geologic logs of the holes are generally quite simple, and frequently record only major lithologies and depths to the top and bottom of the coal seams, together with hole collar survey information. A header card is prepared for each drill hole showing: Hole ID Northing Fasting Elevation Azimuth Dip The header card can be followed by any number of downhole lithologic intercept records: [Hole Depth Lithology Hole ID From-To Coal] Less data errors occur if the computer cards are punched directly from drill hole logs, thus eliminating opportunities for mistakes in transcribing data. All arithmetic manipulations should be left to the computer to avoid as much human error as possible. The SURVEY program is run over the raw data file and all lithologic intercepts are computed and defined in XYZ space. BOUNDARY SURFACES-COAL SEAMS AND LITHOLOGIC UNITS The most useful computer program for defining coal seams in 3D space is a linear inter-

Jan 1, 1980

By John J. Childress, Russell L. Cook

Stringent environmental regulations, which have limited the use of sludge ponds, coupled with the economic incentive to clean more coal or to add fine coal cleaning additions to existing preparation plants have increased the use of static thickeners in preparation plants. The Lamella Gravity Settler, sometimes designated Lamella Thickener, is a shallow depth sedimentation device which has been applied in a variety of industrial process and wastewater control projects in place of the conventional raked thickeners. This paper presents the theory and design of the Lamella Thickener, as well as describing the operating results from several full scale installations in a variety of Appalachian preparation plants.

Jan 1, 1979

By L. F. Mondolfo, F. A. Crossley

SURFACE effects in the brittle fracture of materials such as glass and in the plastic slip of zinc and cadmium crystals are well known.' Recently, another surface effect has been found for zinc monocrystals. It has been observed that certain normally ductile zinc monocrystals become ex- tremely brittle when their surface is coated with a layer of oxide or copper plate.

Jan 1, 1952

By W. F. Sullivan, J. R. Coleman

The use of radioisotopes in obtaining basic information on large scale industrial processing is illustrated with two examples. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. The examples show the advantages associated with the industrial use of tracers as well as the limitations. The Atomic Energy Commission regulations governing the use of radioisotopes in this manner are also discussed. The nuclear properties of radioactive isotopes have provided a new technique for obtaining basic information on large scale industrial processing. A small portion of the process stream is made radioactive by mixing with a suitable radioisotope or by irradiation in a nuclear reactor. The "tagged" portion is then part of the normal process stream and can be followed by detection and measurement of the associated radioactivity. The advantages of radioactive tracing over other forms of tracers are well known, and include such factors as chemical similarity, capability of precise determination of very small quantities due to the high sensitivity of detection apparatus, and the absence of foreign element contamination of the final product. This report will illustrate two applications of the use of radioactive tracers in large scale industrial processing which have provided information that would have been hard to obtain by other means. The first is concerned with the operating characteristics of a kiln scrubbing tower and the second with those of a Hardinge ore mill. ATOMIC ENERGY COMMISSION REGULATIONS Atomic Energy Commission approval can be obtained by qualified personnel if the proposed quantity of radioactivity does not exceed AEC's standards for

Jan 1, 1965

By James E. Breland

A case study of tangible and intangible costs incurred by a coal mining company for meeting the requirements of the Federal Coal Mine Health and Safety Act of 1969 is discussed. For clarity, the data is presented on a "before and after" basis, with special emphasis on safety records, costs, and production performance. The cost figures have been subjected to outside verification.

Jan 1, 1975

By A. E. H. Bergmann

INTRODUCTION The Sachtleben Chemie GmbH in Duisburg, a subsidiary of the Metallgesellschaft AG, operates a new sulfuric acid plant that employs fluid bed roasting of pyrite concentrates. The plant produces about 300,000 tons per year of pyrite cinders from the fluid bed roasting unit. The cinder product consists of 58 percent iron and is about 80 percent by weight smaller than 50 microns. This cinder product was found to be a competitive source material for the cement industry as the iron-containing additive. However, the extreme fineness of the cinder and its dusting tendency were undesirable and an agglomerating technique became necessary. In order to keep the price of agglomerated pyrite-cinders at a competitive level, the agglomerating method must be chosen such a way the capital and operating costs are low. Initial experiments were carried out on a laboratory scale to make an appropriate choice of the agglomerating method. Major goals of agglomerating the cinders were to improve the transportation, storage, and proportioning and metering properties. Minimum specifications are put on the size, size distribution and shape of the product. Criterion for handling is that a minimum of minus one mm. fines are produced after several handlings, while for storage, it is also desirable for the agglomerated product to survive several months in open air. Thermal agglomeration processes such as sintering one known to produce excellent products, but are by far too expensive for our application. For the same reason, granulation, balling, and pelletizing tests with addition of organic binding agents, such as tylose, starch, sulfite wash, molasses, etc. were not continued. The costs for the binding agent was considerable, which is probably due to the high pore volume of our cinders (35 %). Furthermore, the pellets or granules

Jan 1, 1977

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the '(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

By J. Parke Channing

The Miami orebody occurs in an altered Pinal schist. It is popularly known as one of the '(porphyry " deposits but, as at Inspiration and Ray, the ore is an altered mincralized Pinal schist. The orebody mined is the zone of secondary enrichment. Speaking in general terms, the area of the orebody at Miami may be considered as 1000 ft. long and 800 ft. wide. The vertical thickness varies from 200 to 400 ft., so that it is an extremely irregular mass. The study of the ground movement and resulting subsidence at Miami is complicated by the fact that the formation is not homogeneous throughout the mining area, the orebody terminating on its eastern extremity at a fault plane adjoining the Gila conglomerate. This conglomerate is a recent sedimentary deposit somewhat analogous to glacial drift and consists of boulders of granite, schist, and other material cemented with clay, and at times is quite hard. The fault dips eastward at an angle of 45". The original method of mining was top slicing, the slices being 10 ft. thick. At first, there was a good deal of experimenting with mining methods. Some undercut rooms were tried, and the stopes were filled with broken ore with the idea of removing intervening pillars by top slicing. The adoption of the top-slicing method in itself involved considerable experimenting, including some experiments with a long-wall system. The method finally adopted involved the operation of top slicing areas 250 ft. square, each with a central supply raise and ore-gathering raises, each block being worked as a unit. Mining operations in the Captain orebody, which connects with the boundary of the Inspiration property, were started by the room-and-pillar system, the rooms extending across the orebody, with widths of 10 to 15 ft., with 15- to 10-ft. pillars between. The intent was to operate the rooms as shrinkage stopes, permitting the pillars to crush when the ore was drawn from the rooms. It was found that the shrinkage stoping was unnecessary, so a system of block caving was adopted. This system was so successful in the Captain orebody that, about three years ago, the method of mining in the orebody was changed from top slicing to block caving, the method now in use. The block caving system, as practiced

Jan 1, 1923

The volumes of Transactions, which are published annually, contain the list of officers, rules, etc., the Proceedings, and the papers revised for final publication. (In this revision, after the preliminary publication, authors are permitted to use the largest liberty; and the changes and additions made in papers are sometimes important. It should be borne in mind by those who study or quote a paper in the preliminary edition, that they may not have in that form the ultimate and deliberate expression of the author's views. It should be added, however, that in the majority of cases there are no important changes.) These volumes are for sale as follows, in paper covers:

Jan 1, 1910

By A. Long, A. Silverman, J. L. Kulp

Garth Crosby has written an excellent geologic description of the deposits surrounding the Gem stocks in the Coeur d'Alene district. The ore deposits in the area of the Gem stocks may hold the key to the age and mineralization history of the entire Coeur d'Alene district. A recent isotopic study of the Coeur d'Alene district in this laboratory illustrates that a classical geologic interpretation of these deposits, with its implications for the whole district, may lead to erroneous conclusions. For this reason it seems pertinent to submit a summary of these results and an interpretation of the mineralizing history of the Coeur d'Alene districts.

Jan 5, 1960

By S. S. Deshmukh

An important element of evaluating a materials- handling system by simulation lies in being able to examine the details of the proposed operation in a fashion which closely approximates real behavior. The added factor of flexibility permits including or deleting those parts of the problem which can be shown to be important or trivial. Used carefully, simulation can match manpower and equipment far more efficiently than conventional calculations. The same is true of interacting equipment systems. This efficiency results from being able to simulate the real fluctuations in a system by using empirical probability distributions compiled from existing operations. Simulation eliminates guessing as to efficiency, absenteeism, bunching, and the broad host of delays that influence productivity and substitutes operating data in place of the usual factors. In this respect, simulation improves detail and confidence in the reliability of engineering estimates.

Jan 1, 1970