Search Documents

By D. L. Harris

Chemical upgrading testwork on Stillwater chomite concentrate shows that reduction roasting and leaching (sulfuric acid and/or ferric sulfate) can provide upgraded feed to ferrochromium furnaces for making upgraded ferrochromium. Two-stage reduction smelting in electric arc furnaces can make upgraded ferrochromium also. Sulfating roasts and leaching (acid and/or water) results using gaseous SO2—SO3 or solid ammonium sulfate were not satisfactory for upgrading chromite. Chemical upgrading of domestic Stillwater (Montana) chromite has been considered at various times1'2' to provide a material with higher chromium to iron ratio, more like foreign high grade ore, for the production of standard grade ferrochromium. Physical bene-ficiation of Stillwater chromite ore can provide a ratio, Cr/Fe, no higher than the ratio in the chromite mineral, which is approximately 1.7. For comparison the analyses of a foreign metallurgical grade chromite ore, a high grade electrostatic process Stillwater concentrate and a stockpile concentrate from the Stillwater ore are noted in Table I. Single stage smelting of the high grade foreign ore with a ratio, Cr/Fe, of 3.37 can provide a ferrochromium of over 65 pct chromium content. Similar smelting of the Stillwater concentrate with a ratio of 1.7 can provide a ferrochromium of 50 to 55 pct chromium content.' It has been demonstrated on a pilot plant scale that chemically upgraded Stillwater chromite having a ratio, Cr/Fe, of 3.0 also can be smelted to provide a ferrochromium containing over 65 pct chromium.5 Two major considerations for an upgrading process are the ratio, Cr/Fe, in the product and the chromium recovery. A minimum ratio, Cr/Fe, of 3.0 is required in the product but for economic reasons a higher ratio is desirable for blending purposes as long as the recovery is satisfactory. Data from different kinds of chemical upgrading testwork are presented in this report. Some of the testwork was conducted to make a product which was not intended to be feed for ferrochrome smelting, but the data are considered pertinent to chemical upgrading. Results reported by others are noted also for comparison. WORK REPORTED BY OTHERS The U. S. Bureau of Mines has contributed much to the literature on chemical upgrading of chromite and a summary is given in Table 11. Reduction roasting and acid leaching were reported by Boericke and Bangert,1 by Lloyd and Gorst, et a1,2 and by Boericke3 to demonstrate very good success on a laboratory scale and only fair success in pilot plant tests for Stillwater (Benbow) concentrates. This work included basic studies on thermodynamic properties to explain the reduction and leaching results. Canadian workers, Downes and Morgan,9 have reported experimental success in upgrading a low grade Bird River chromite, similar to Stillwater material by the same process. Russian workers1' have noted results on reduction tests of high grade chromite which may apply to low grade ores and which help in understanding the reduction process. The use of flux additives in the reduction process was an innovation of their work. The Canadian workers9 also reported other kinds of experiments, including autoclave leaching of the chromite in a limited amount of sulfuric acid. An insoluble basic chromium sulfate was formed and separated from soluble iron, magnesium, and aluminum sulfates to provide an upgraded material. U.S. Bureau of Mines workers, Lloyd, Rosenbzum, Home and Davis,' reported on autoclave leaching of Benbow concentrates as a means of obtaining chromium alum for electrolysis. This last work required selective crystallization of alum to separate iron from chromium. Chloridizing roasting of Benbow and Mouat concentrates has been reported by Hunter and Banning6 and others8 to show that the iron chloride could be volatilized from the chromite to provide upgraded residues.

Jan 1, 1964

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By Daniel Hanson

FoR most of their practical applications metals are required to withstand stresses of appreciable magnitude: indeed, it id because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances—or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By H. I. Aaronson, H. A. Domian

The self-diffusivity of Ag10 has been measured as a function of temperature and composition in AgMg. a CsCl-type intermetallic compound with a substitutional defect structure on both sides of the stoichiometric (50 at. pct Mg) composition. These measurements show that In D increases linearly, and both In Do and Q decrease linearly with deviation from stoichiometry. The slopes of these lines are significantly steeper in magnesium-rich alloys. Equations for the variation of Q with composition have been derived by application of the theory of random walk processes on the assumption that diffusion in compounds of this type takes place by the six-jump cycle mechanism of Huntington, Elcock, and McCombie. The favorable agreement obtained with experiment furnishes fresh support for the correctness of this assumption. A principal result of this treatment is that. although the concentration of vacancies is considerably higher in the silver sublattice than in the magnesium sublattice, the acfivation energies for movement of the magnesium sublattice vacancies are so much lower that these vacancies are responsible for effectively all diffusion of silver in this compound. A tendency for vacancies of both types to be kinetically bound to wrong atoms is also noted. THIS study was undertaken to examine the influence of substitutional defects upon self-diffusion in an intermetallic compound, AgMg, with a CsCl-type crystal structure. The CsCl structure is exception- ally simple. At the equiatomic or stoichiometric composition in a binary alloy, it consists of two interpenetrating simple cubic sublattices, each of which is exclusively populated by the atoms of one species. When atomic size and other factors are favorable, deviations from stoichiometry can be entirely accommodated by the substitution of atoms of the species present in excess of 50 at. pct on the sublattice of the other species on a one-for-one basis. Under this condition, the only vacancies present are those formed by thermal activation. The excess atoms thus incorporated into the sublattice of the minority species may be considered as substitutional defects in this sublattice. Several X-ray studies have shown that the defect structure of AgMg is entirely of the substitutional type on both sides of the stoichiometric composition.1"3 The thermodynamic investigation of Kachi indicates that, aside from a low level of thermal disorder and these constitutional defects, order is maintained to the solidus temperature. This compound is therefore a particularly useful vehicle for a study of the influence of substitutional defects upon diffusion kinetics. Other advantages of AgMg for this purpose include: the broad composition region, as much as approximately 10 at. pct on either side of the stoichiometric (50 at. pct Mg), in which the compound is stable; the comparatively low temperature range of the solidus (820°C and below),5 making diffusion anneals near this range experimentally convenient; the reasonably good machinability of the compound, permitting utilization of the standard sectioning method of radiotracer analysis; and the availability of a good tracer, A for one of the constituent species. While this investigation was in progress, Hagel and westbrooks reported data on the self-diffusion

Jan 1, 1964

By A. N. Mitinsky

Discussion of the paper of A. N. MITINSKY, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1697 to 1705. LAWFORD H. FRY, Burnham, Pa. (communication to the Secretary*). -The author assumes that the proportional limit and the elastic limit are coincident or very nearly so, and then further assumes that the stress corresponding to these two points is the least stress which if repeated will cause failure. The point is extremely interesting and it is to be regretted that the author did not quote experimental data to show the relation between the limit of repeated stress and the other properties of the material. The author's suggestion that a steel of poor quality may have a normal value for the yield point and tensile strength (see Fig. 2) and an abnormally low elastic limit, and that this will correspond to a low resistance to repeated stress, may account for a number of failures of axles in which the tensile tests show normal physical properties. If so and if a determination of the proportional limit would have eliminated the material before it was put into service, this determination will merit most earnest attention. It appears, however, that considerable further research is necessary before any definite conclusion as to the quality of a steel can be drawn from its proportional limit. Mr. Mitinsky's paper is extremely interesting and if it stimulates thought and work along the lines indicated, it may prove of considerable practical benefit. H. V. WILLE, Philadelphia, Pa.-The paper discusses the difference between the proportional limit, or elastic limit, and the yield point, and refers to the fact that much harm results from confusion of the terms yield point and elastic limit. Similar confusion has arisen in this country; the American-Society for Testing Materials does not even consider the elastic limit and proportional limit to be identical and recently adopted the following definitions:

Jan 12, 1915

By B. M. Larsen

A discussion based on three commercial furnace tests and electrical analogue calculations is presented. It shows that while regenerator efficiency is mainly dependent on loading or relative amount of heat exchange surface plus the heat transfer coefficients as effected by flow velocity, the actual air preheat temperature can be high or low, largely independent of regenerator efficiency, mainly due to the diluting or unbalancing effects of cold air leakage into various parts of the furnace system. THERE are many signs of a renewal of interest in the heat regeneration aspect of the open hearth process, among them being the recent paper by Marsh,' the introduction of auxiliary checkers in the stacks of the Isley furnace design, and a number of recent installations of two-pass checkers in new and old furnaces. However, there are also signs of yielding to the usual temptation of oversimplifying a problem. Faced with the job of obtaining better draft on a furnace, for example, a good designer always recognizes that focusing attention on some one factor, such as height of the stack or capacity of the exhaust fan, does not make his problem any easier; rather he must look at the whole system, including such items as valve resistances, bends in the flues, and flow resistance in the waste heat boiler; then he must make his design in relation to the available draft so as to avoid any serious bottleneck in the system. Yet this example is really much simpler than the problem of air preheating, and again, the latter problem is not really made easier by concentrating on air temperature in uptakes and on the more obvious methods for making this air as hot as possible. Also to be considered are such things as the total amount of air needed theoretically for complete combustion at any selected fuel rate, together with that needed for oxygen absorbed into the bath and for burning the combustible gases given out from the bath, plus some excess air. Furthermore, how does this total air requirement relate to the regenerator efficiency at various loadings? How much of the total air equivalent in stack gases will come from preheated air passed through the whole length of the incoming regenerator and how much from air leakage into various zones of the whole furnace system? Does the effect of leakage air differ depending on whether it leaks into the ingoing regenerator, the furnace above floor level, the outgoing regenerator, or the stack zone? Over a number of years we have in this Laboratory experimented with methods for measuring hot gas temperatures; we have measured, approximately, the efficiency of a few regenerators on commercial furnaces and we have developed an electrical analogue' for calculations of regenerator efficiency. The whole problem is too complex to cover in one paper even with a more complete background of data than we possess, but we can attempt here to clarify certain aspects in a general way, hoping to assist specific plant studies on individual furnaces. Some of our earlier experience has been incorporated into chaps. 4, 19, 20, and 21 in the book "Basic Open Hearth Steelmaking,"" and on the assumption that this text is available to most readers, this discussion has been shortened by references to that book. The most recent design of a flowing-gas thermocouple which we are now using for measurement

Jan 1, 1955

By J. P. Doan, G. Ansel

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By G. Ansel, J. P. Doan

The important literature concerning zirconium in magnesium-base alloys is predominantly contained in patent references. Sauerwald, Eisenreich, and Holubl-4 discovered the profound grain-refining influence of small amounts of zirconium on cast magnesium and the attendant increases in strength and ductility. They extended their work to reveal that limited amounts of certain other elements, including zinc, could be added for further improvement in strength and hardness. British Patent 5111375 relates to the parent discoveries of Sauerwald, Eisenreich, and Holub. All of these references deal primarily with casting characteristics and properties in the cast state. Minor mention is made of desirable tensile strength, ductility, and toughness of wrought Mg-Zr alloys* modified by one or more additional elements. No extensive reference in the literature5. has been found to the particular characteristics of wrought blg-Zn-Zr alloys, with which the present paper is concerned. The work to be discussed represents essentially an extrusion study of the blg-Zn-Zr alloys and indicates that this system is highly interesting in the wrought state both academically and commercially. Accordingly, an important aim of this paper is to describe the hot-workability, tension and compression properties, metallography, and toughness of these alloys. Compositional variations are limited to the ranges 0 to 7 per cent Zn and 0 to I per cent Zr. Experimental Procedure Alloying and Casting Alloying ingredients were cell magnesium, commercial zinc (intermediate grade), and a chloride salt containing approximately 50 per cent ZrCl² and 50 per cent alkali chlorides. This salt is produced by Titanium Alloy Manufacturing Company. Melting, alloying, and pouring procedure essentially followed the crucible process as described by Nelson.6 The magnesium was melted using Dow No. 310 flux, and the temperature raised to 1350° to 1400°F for the alloying operations. After alloying of the zinc, the zirconium containing salt was added in small portions with vigorous stirring. This is an adaptation of the method described in British Patent 533264.7 The alloying efficiency of zirconium was approximately 30 per cent. During the alloying of zirconium, fluorspar was added in amount required as a flux-inspissating agent. Next the melt was refined with Dow No. 310 flux and held quietly for 15 min. Finally billets were cast in a book-type permanent mold

Jan 1, 1947

By Joel H. Watkins

The terms kaolin, china clay, ball clay, and paper clay are more or less loosely and interchangeably applied to a large class of white-burning clays. These clays are made up chiefly of hydrous amorphous (colloidal) aluminum silicates with variable amounts of free silica and other impurities in small quantities. Occasionally also the term kaolinite is wrongly applied to a white-burning clay, for kaolinite is a mineral of definite chemical composition and definite crystalline form which occurs but sparingly in nature. It is not the purpose of this paper, however, to define or classify clays, or to enter into a discussion of the chemistry of clays. It is rather a general description of the occurrence and methods of mining of a kindred group of clays, and a discussion of their future economic aspect. In the Southern Appalachian States, the mining of white-burning clays has in recent years become an important industry. Although these clays are of several distinct types, which occur in as many localities under different geologic conditions, they are for the most part primarily of the same origin. They are essentially the same in elementary constituents, and are largely consumed in the game industrial arts. From the standpoint of a mining engineer, therefore, and for convenience in comparison and correlation, it should be interesting to discuss them under one heading. Kinds of Clay The most important types of clay which are now being actively mined in the Southern Appalachian States and with which this paper is particularly concerned are the North Carolina, Virginia, and Georgia kaolins or china clays (residual); the South Carolina and Georgia kaolins or paper clays (sedimentary); and the Florida and Tennessee plastic kaolins or ball clays (sedimentary). Other varieties which are interesting but which are as yet of little importance are the pocket deposits of white clay in Augusta County, Virginia, the bauxitic kaolins of Tennessee,

Jan 1, 1915

By Robert S. Williams

On several occasions, when 60-40 brass is first obtained in the beta condition by quenching at about 825" C. and is then reheated, the writers have noticed that reerystallization will take place in the form of twin crystals at the grain boundaries of the original beta crystals. It was, therefore, thought that interesting results would be obtained if this twinning process was studied further, especially as to the temperature at which it first occurs. The material used in the investigation was a bar of extruded muntz metal, 1/2 in. in diameter, and of the following composition: Copper, 60.21 per cent.; zinc, 39.73 per cent.; lead, trace; iron, trace; tin, nil. Specimens 1 in. in length were sawed from this bar and a hole was drilled into the side of each specimen until it reached the center, and the tip of a platinum-platinum rhodium thermocouple was inserted. A small Hoskins' resistance-type electric furnace was used for heating the specimens. The specimens were first heated at 840' C. for 2 hr. and then quenched ' in cold water, in order to get the material entirely in the beta state. In every case, in the reheating process, the furnace was brought to the desired temperature before the specimen was introduced. The time occupied in preheating was from 20 to 30 min. By sawing back 1/4 in. on each side of the hole, two parts were obtained from each specimen and duplicate observations were possible. The specimens were held at the reheating temperatures for periods of 15 min., 30 min., 1, 2, and 4 hr. All specimens were etched with a freshly prepared mixture of equal volumes of concentrated NH4IOH and H2O2.

Jan 1, 1924

By Dan Crackel, G. G. Ramos, Mark Heisel

INTRODUCTION Feasibility studies indicated that a cratering type stoping method was best suited to the character of the first ore block at Carr Fork. This method known as vertical crater retreat (VCR) has since been modified to a combination cratering and deck blasting using VCR drop raises for initial undercut development . The modified form retains many of the advantages of VCR while allowing high tonnage production blasts which have offset many of the disadvantages. FIRST CONCEPTS AND PREMISES Geologic Considerations The Steep Highland Boy (SHB) skarn orebody, the first of several blocks being developed, is a steeply dipping 70° to 90° limb of a syncline, with a width averaging 25 m (82 ft). The bed has a consistent east-west strike length of over 400 m (1300 ft) and extends from the surface to depths of over 1000 m (3300 ft). The footwall is highly fractured quartzite and the hanging wall grades from garneti te to limes tone and hornfe 1s. Because of the limestone in the hanging wall, the hanging wall appears more competent than the footwall. The ore is garnetite with lenses of massive sulphide and magnetite. The quartzite footwall is highly fractured not only because of the bedding but also due to the folding and intrusion of the quartz monzonite. This irregular footwall outline of some stopes in- creases the likelihood of excessive dilution. The principal ore mineral is chalcopyrite with some bornite. The garnetite ore is quite variable in terms of compressive strength and drillability. In addition to the sulphide and magnetite lenses, it is transected by clay- altered dikes and major and minor north-east faults. TABLE (1) gives the range and mean strengths of the rocks. Investigating Mining Methods Initial consideration of a suitable mining method centered around maximum safety and efficiency with minimum potential dilution. The following major methods were considered and investigated. Cut and fill mining was eliminated because of low productivity, the cost and problems associated with providing fill, and the relatively unsafe nature of the method. Sublevel caving was rejected due to the unpredictable cavability of the waste and the geometry of the ore body. Conventional sublevel or blasthole methods require excessive development, as fan and ring drills are limited to efficient drilling in the 18 to 25 m range (60 to 80 ft). Mining downdip with equipment drilling small diameter holes would have required eight separate extraction/drill horizons with crosscuts and associated excavation in the main ore block. The use of down the hole (DTH) machines cap- able of drilling 165 m (6g in) diameter holes

Jan 1, 1981

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By Roy D. McLellan

Electrolytic production of cadmium at the Great Falls plant started in the first part of the year 1925. Prior to that time, an experimental unit had been in operation for a few months during the year 1922. At present the plant is the largest producer of cadmium, not only in the United States but in the world. Electrolytic cadmium is characterized by its very low content of impurities. The main impurities, which are lead, copper, zinc and iron, do not aggregate more than 0.05 per cent., leaving a cadmium content better than 99.95 per cent. The consumption of cadmium has increased rapidly since the war, with the growing use in the plating industry. Cadmium plating has come into prominence because of its connection with the automobile and radio industries. As a protective coating, a deposit of cadmium is superior to zinc. Cadmium is also used extensively in alloys. Important among these is the alloy with copper used in telephone and trolley wire. In proportion of 0.5 to 1.2 per cent., cadmium adds materially to the strength and wearing qualities. Practically all commercial zinc concentrates contain a small amount of cadmium. In the electrolytic zinc process, the cadmium that is dissolved in the regular leaching operation is removed from solution with metallic zinc, generally added in the form of zinc dust. This precipitate also contains the copper taken into solution and the excess of zinc dust, which is required in order to insure a complete removal of all impurities. The precipitate is treated by a separate process to recover the copper, cadmium and excess zinc. In order to make the metals more soluble and to render insoluble such impurities as iron, arsenic and antimony, the precipitate is roasted. The roasting is carried out in gas-fired McDougall furnaces, with a roasting temperature of about 700' C. The roasted residue is leached with dilute sulfuric acid, spent electrolyte from the zinc electrolyzing, containing 10 to 12 per cent. free H2S04. The leaching is done in cylindrical tanks of 30 tons capacity, agitated

Jan 1, 1930

By F. George, W. Tice, M. Salkind

It was found that Al-A13Ni could be readily cold rolled perpendicular to but not parallel to the whiskers. Reductions of more than 98 pct were achieved without cracking by rolling perpendicular to the whiskers, whereas extensive edge cracking was noted after only 15 pct reduction when rolling parallel to the whiskers. The longitudinal and transverse tensile strengths were nearly doubled, and the longitudinal yield strength more than tripled by cold rolling 50 pct in a direction perpendicular to the whiskers. The whiskers exhibited some waviness (elastic bending) as a result of cold rolling, but at very high reductions (greater than 75 pct) whisker fracture and misalignment became significant. A fine dislocation substructure in the matrix consisting of cells attached to the whiskers was pro -duced by cold rolling. Most of- the substructure was readily removed by a 1-hr anneal at 500°C. Cold rolling was found to substantially reduce the thermal stability of the microstructure at 610°C but did not affect the stability at 500°C. FIBER and whisker reinforced composite materials promise significant improvements in properties over conventional materials. Before they find wide use, however, it will be necessary to understand the response of these highly anisotropic materials to common metalworking processes. Most of the nonmetal-lic fiber reinforced materials have very low elongations (a few pct or less) in the direction of fiber alignment. Thus, metalworking techniques such as rolling and forging would not be as broadly applicable to these materials. This investigation was initiated to determine how a composite system consisting of Al3Ni whisker reinforced aluminum responded to rolling, what changes in the microstructure occurred, and the effect of deformation on the mechanical properties. The composite material studied was produced by unidirectional solidification of the A1-Al3Ni eutectic alloy'-7 and consisted of 10 pct by volume of aligned whiskers of Alai in a matrix of aluminum. It should be pointed out that this system is not representative of all composite materials, and the results will therefore not be universally applicable. The A1-Al3Ni system is characterized by: 1) A strong fiber-matrix interfacial bond 2) A ductile matrix 3) A sufficiently low fiber content to allow significant plastic flow between fibers 4) Strong, completely elastic whiskers (tensile strength 400,000 psi, elastic modulus = 20 X 106 psi.1 These factors allow the material to be readily rolled perpendicular to the fibers. If the fiber-matrix bond were not strong, such a weak interface could fail during rolling. A measure of the ability of a composite to be rolled in the transverse direction can be obtained from noting the transverse tensile behavior. In the case of Al-Al3Ni,2 there is considerable ductility (15 to 30 pct). In the case of boron filament reinforced aluminum, for example, the transverse elongation is less than 1 pct,8 and the material could probably not be cold rolled as readily in that direction. EXPERIMENTAL PROCEDURE 3-in. diam ingots of A1-A13Ni eutectic were unidi-rectionally solidified in graphite crucibles. The starting materials consisted of 99.99+ pct pure nickel and aluminum, and the pure eutectic ingots were made with 6.2 wt pct Ni. The unidirectional solidification process (described in detail elsewhere1-3) consists of preparing a master heat of eutectic composition, remelting, and withdrawing the ingot vertically downward through the heat source at a controlled rate so that plane front solidification proceeds upward at a constant velocity. The resulting microstructure consists of 10 pct by volume of whiskers of very high aspect (length to diameter) ratio. The fiber lengths have not been measured because of the difficulty of detecting fiber ends9 but exceeds 104. There is some possibility that the fibers may be continuous within one grain. Flat sheet specimens 2¾ in. sq and approximately 0.2 in. thick containing whiskers parallel to the plane of the sheet and to one edge were used for this study. A1-A13Ni exhibits either a rod-like (high solidification rates) or a blade-like (low solidification rates) whisker morphology,1,3 and both types were studied. Rolling was accomplished using a two-high rolling mill at a speed of approximately 10 fpm. The rolling direction was either parallel to or perpendicular to the direction of growth (direction of whisker alignment). Reductions of from 0.002 to 0.03 in. per pass were used with the most common value being 0.005 in. per pass. Cold rolling of Al-Al3Ni to more than 98 pct reduction in thickness was accomplished with no intermediate anneals. In addition. a series of speci-mens was cold rolled 97 pct with a 1-hr, 500°C anneal in air after each 50 pet reduction. Tensile testing was accomplished using a Tinius-lsen four screw testing machine. Flat sheet specimens + in. wide and between 2 and 2; in. long with the thickness dependent upon rolling reduction, were used. The gage section was in. wide and 1 in. long. Strain was measured using a clip-on LVDT extensome-

Jan 1, 1970

By R. W. Raymond

Under the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been, that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them—Texas—came into the Union by its own voluntary

Jan 1, 1913

By James D. McClung, H. J. Gluskoter, M. R. Geer

INTRODUCTION The purpose of coal preparation is to improve the quality of coal to make it suitable for a specific purpose by (1 ) cleaning to remove inorganic impurities; (2) sizing-crushing or screening, or both; or (3) special treatment, such as dedusting. The properties and quantities of impurities in coal are of major importance in the design and operation of steam generating equipment. Al- though boilers are often designed and equipped to use a wide range of coals, no boiler will perform equally well with all types of coals. All coals have certain properties that place limitations on their most advantageous use. These limitations are especially stringent for many of the older installations. Because of a general lowering of quality of raw coal in recent years, the need for coal cleaning has significantly increased. Among the factors contributing to the need for increased coal preparation are (1) increased demand for quality brought on by market and environmental requirements; (2) increased extraneous dilution caused by mine, health, and safety laws; and (3) depletion of the higher-quality coal seams.

Jan 1, 1979

By H. H. Campbell

Many attempts have been made to write a formula by which to calculate the strength of steel from its chemical composition, but most of these endeavors have failed because there were too many disturbing conditions. It is idle to collect from the pages of trade-papers, books, or the proceedings of scientific societies, a multitude of observations. The combination of such results will simply show that steel of the same composition will vary in tensile strength through wide limits—a fact that has been known for generations. That cold-working, overheating, and many another form of heat-treatment alter fundamentally the strength of steel, is ancient history, although it is only recently that the microscope has pointed out the road to an explanation of the phenomena. It mag be urged that the microscopic structure must betaken into consideration in any formula giving the ultimate strength, but from the standpoint of the present investigation this is unnecessary. We are trying to determine primarily, not what changes in ultimate strength may be made by variations in the condition of carbon, but what effect is produced by changes in the amount of carbon, when its condition remains constant. For such an inquiry, in order that the condition of the carbon should remain as nearly uniform as possible, it is essential that all testrpieces be made under the same conditions; and it is believed that the tests described in this paper satisfy that requirement. The investigations were made at the works of the Pennsylvania Steel Company, Steelton, Pa.; the ingots from which the tests were made were 6 in. square in every case; they were heated in the same furnace and forged at the same ham-

Jan 1, 1905

Continued Discussion of the papers of Van Hise, Emmons, Weed and Lindgren, Bans., xxx., 27, 177, 424, 578. See also the papers of Vogt, Kemp, Rickard, Blake and Lindgren, at pp. 125, 169, 198, 220, 226, and also the final contribution of Prof. Van Hise, p. 284 of the present volume. All the foregoing, together with the discussion here following, are included in the special volume, "The Genesis of Ore-Deposits," issued this year by the Institute. H. Foster Bain, Des Moines, Iowa (communication to the Secretary):* The zinc- and lead-deposits of the Mississippi valley, which it has been my fortune to study, give particularly good examples of many of the principles of ore-deposition formulated by Prof. Van Hise. Perhaps there is nowhere clearer evidence supporting his fundamental tenet., that ore-bodies are to be regarded as a result, and as merely one of the phases, of the work of underground waters. The facts regarding the mines of the upper Mississippi valley have been given in some detail for Wisconsin by Prof. Chamberlint and, more recently, for the mines west. of the Mississippi by the Iowa Geological Survey.‡ Fortunately, also, the processes of underground water-circulation have been studied in some detail in connection with the investigation of artesian waters throughout the region.$ In Missouri and Arkansas the mines and ore-bodies have been much studied ; but the general problems of the circulation of underground waters have been neglected. During the season just closed the writer has been engaged in a re-study for the United States Geological Survey of the zinc- and lead-deposits of the Ozark region, with special reference to those of the . Joplin area; and his full report is now in preparation. It has been interesting to note how fully the statement that the orebodies result from the general action of underground waters is

Jan 1, 1902

By Gilbert Santoro

In this study tantalum carbide filaments of various compositions in the fcc region were prepared by heating a tantalum wire in a measured amount of hydrocarbon vapor. Such properties as tensile strength, transverse-rupture strength, microhard-ness, lattice parameter, electrical resistivity, and magnetic susceptibility were measured as a function of carbon content. Some of these properties showed a maximum or a minimum between a carbon-to-tantalum molar ratio of 0.80 and 0.85, the composition range at which the color changes from metallic gray to gold. The recent literature has shown that in the large homogeneity range for the fcc phase of the Ta-C system there is a marked variation for such properties as microhardness,' electrical resistivity, ' thermodynamic properties,z'3 lattice parameter and superconductivity. In addition to the technological interest of these variations within a single phase, important theoretical benefits may ensue from a continuous investigation of properties vs stoichiometry in tantalum carbide and other refractory defect compounds, for example the effect of the metal-metal distance and crystal structure upon bond formation and electronic structure. Whether there is a similar variation of the tensile strength is of practical importance. Of theoretical interest would be the knowledge of how the magnetic susceptibility varies with carbon composition. Both of these properties, as well as the transverse-rupture strength, were determined for tantalum carbide filaments in the fcc phase region. The lattice parameter, the electrical resistivity, and the microhardness were also investigated and compared with values appearing in the literature. EXPERIMENTAL PROCEDURE Material Preparation. Tantalum carbide specimens of various carbon content were prepared by statically carburizing high-purity tantalum filaments in measured quantities of pure hydrocarbon gas. The filaments, which were 10 mil in diameter and 20 or 40 cm long, were heated by their own resistance at temperatures from 1800" to 2200°C using alternating current in some cases and direct current in others. Tantalum wire from two sources was used. One had a reported purity of 99.96 wt pct Ta. The ingot from which this wire was drawn had been electron beam-melted as the final step in its purification. The reported purity of the other wire, which was prepared by a powder metallurgical process, was 99.88 wt pct Ta. The impurities of both tantalum sources are listed in Table I. Spec-trographic-grade toluene or research-grade propane was used as the source of carbon. The apparatus for the carburization of the filaments is shown schematically in Fig. 1. The system was evacuated to 1 x l0-' mm of Hg when using the electron beam-melted tantalum and to less than 1 p when using the less-pure tantalum. Neither the difference in the base vacuum, nor in the hydrocarbon gas, nor in the tantalum filaments resulted in any detectable difference in the properties studied in this work. However, only the carbides prepared from the higher-purity tantalum were used in the magnetic-susceptibility determinations. Once the base vacuum had been reached, the system was flushed with the hydrocarbon and re-evacuated. For any desired composition of the carbide, hydrocarbon gas was allowed to leak into a constant-volume flask to a predetermined pressure. These pressures were measured by a Cartesian diver-type mercury gage with a range from 0 to 20 mm and with a scale expanded to nine times. The hydrocarbon gas was allowed into the reaction tube and the filament was quickly raised to the reaction temperature. The slack in the filament due to thermal expansion was taken up by drawing out the movable electrode with a screw mechanism. The filaments were kept at temperature from a few minutes to 200 hr. In the majority of cases the heating time was 6 hr. The reaction tube was cooled by cascading water on its outer surface. By means of an ammeter and a voltmeter the electrical resistance at the reaction

Jan 1, 1963

By A. L. Galpin

INTRODUCTION For many tailings ponds, particularly those having substantial watershed areas, the control of pond water levels will be a major factor influencing the operation of the pond and the design and construction of the dam retaining the pond. This paper summarizes the basic factors affecting the control of water in tailings ponds, methods of water control, and methods of estimating the variables involved. The influences that pond water levels can have on the design, construction, and stability of tailings dams are explained in order to emphasize the importance of water control in the overall planning of mine tailings disposal systems. Two examples of pond water control planning conclude the paper. BASIC FACTORS The principal factors influencing the control of water in tailings ponds are illustrated on Fig. 1. Fig. 1 (a) shows the general disposition of the tailings solids and water in the pond; the solids settle from the slurry to form "slimes", deposits sloping down into the pond from the points of discharge; these slimes hold volumes of water in the voids between solid particles; water in excess of this "retained" water forms a pool of "free" water laying over the slimes deposits. In some cases, tailings solids (and water) go to the tailings dam for its construction. Fig. 1 (b) indicates those ways additional to tailings disposal in which the pond gains or loses water. These include surface and sub-surface runoff from the pond watershed, water reclaimed from the pond for ore processing, evaporation, and seepage. Seepage losses sometimes include water draining from tailings sand placed in the dam, but a portion of the total seepage flow is often collected and returned to the pond in order to avoid downstream pollution and to recover water for re-use. PRINCIPAL REQUIREMENTS In relation to the control of water in a tailings pond, the first requirement is usually to maintain a pool sufficiently large to ensure adequate clarification of the free water prior to its reclaim for use in the mill, or its discharge from the pond.

Jan 1, 1972