Search Documents

By John Griffen

THE modern anthracite breaker or washery uses almost completely a wet method of preparation, which requires, roughly, 1 gal. of water per minute per ton of production per day. The entire anthracite industry uses about 320,000 gal. per min. of water for this purpose or 800,000 tons of water per day. As this water leaves the breakers, it contains fine solids-coal, slate, pyrite, and clay-and is then called silt or slush; as slush is the term most commonly used, it will be employed throughout this paper. The solid content of the slush will be referred to as solids. In the earlier days of anthracite mining, little coal was washed, less crushing was employed, and virgin coal was mined exclusively. As a result, the slush problem was not acute because of the relatively small quantity and the coarseness of the solids. Such slush as was produced could usually be easily impounded and retained or could be discharged into streams without any appreciable pollution being apparent. The character of the fine waste from the breakers, changed materially as its quantity increased until now about 40,000 tons of slush solids are produced daily. Second mining and robbing operations materially increased the quantity of fine solids delivered to the breaker in the mine car. The demand for chestnut, stove and egg sizes, to the exclusion of grate, steamboat, and lump sizes, require finer crushing of the mine-run coal with a consequent increase of fine solids in slush. The use of rice and barley sizes removed a considerable tonnage of coarser solids from the slush but left great quantities of fine solids difficult to retain completely and store and long considered of no possible fuel value. Despite the efforts of the coal operators, the slush solids have found their way into the streams causing, in some cases, serious pollution. The Water Supply Commission of Pennsylvania published, in 1916, a report on Culm in the Streams of the Anthracite Region,1 from which the following is taken: About 40,000,000,000 gal. of water carrying 10,000,000 tons of fine culm are discharged into the water-courses direct, flushed into the mines, or disposed of by various means on the surface. The extent to which the very small sizes of anthracite

Jan 9, 1921

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By W. A. Ver Wiebe

Under the impetus of new demands caused by the war, the oil and gas industries of Kansas established new records during the year 1942. In all, 1513 test wells were drilled, which is somewhat of a drop from the figure of 2113 for 1941. The 1513 tests yielded 800 new oil wells, 85 new gas wells, and 628 dry holes. Thus there was an increase in two categories, the gas wells and the dry holes. Considering that last year only 592 dry holes were completed out of a much larger total, the figure of 628 dry holes causes some concern among local operators. The increase in unsuccessful tests illustrates once more the fact that each year it is becoming harder to find the remaining oil pools. When the figures are broken down, it appears that western Kansas accounted for 1177 tests, of which 689 were oil wells, 33 gas wells, and 455 dry holes. The total potential daily initial production uncovered by the successful wells amounted to 753,178 bbl. of oil and 619,734,000 cu. it. of gas. The figures for new initial production indicate a substantial drop from last year's figure of 1,691,000 bbl., and the figures on gas are slightly higher. In 1941 the new gas as based on a daily potential was 508,000,-000 cu. ft. In eastern Kansas, 336 wells were drilled. Among these in were oil wells, accounting for a daily initial potential production of 16,199 bbl. The new gas wells numbered 52 and added 253,725,000 cu. ft. per day to the gas potential production of the state. The remaining tests, 173 in number, were dry. It is interesting and perhaps significant that about half (630) of the wells drilled in western Kansas were drilled by the independent operators. Among the large companies, the Cities Service Oil Co. drilled 163 wells; the Stanolind Oil and Gas Co., 52; the Skelly Oil Co., 39; the Continental Oil Co., 48; and the Shell Petroleum Co., 21 wells. In eastern Kansas the independent operators drilled 297 out of the total of 336 wells. Among the major oil companies the Cities Service Oil Co. drilled 19; the Phillips Petroleum Co. 7; and the Sinclair-Prairie Oil Co., 6 wells. The figures based on relative percentages of dry holes to successful oil or gas wells are revealing. In western Kansas almost one half of all wells drilled by the independent operators were dry holes. The major oil companies drilled approximately 547 wells in western Kansas, of which 379 were successful in finding either oil or gas. It thus appears that the major companies fared better than the independents. In eastern Kansas the major companies drilled 39 wells, of which 29 were successful in finding commercial quantities of oil or of gas. No less than 329 wildcat test holes were put down in western Kansas and 105 in eastern Kansas, or 434 in all, during 1942. Considerably more than half of these were drilled by independent operators; 223 in western and 99 in eastern Kansas. An exploratory hole 56 mile or more from production is regarded as a wildcat well in Kansas. On a percentage basis, about 80 per cent of wildcat wells were failures. In western Kansas only 20 per cent found either oil or gas. The failures were about equally distributed among the major

Jan 1, 1943

By Henry M. Howe

The object of the present paper is to suggest injecting into the hearths of iron blast furnaces, whose temperature has become unduly lowered, some form of fuel whose calorific intensity, under the peculiar conditions existing there, is considerably higher than than of liquid petroleum, the rose of this substance for melting out chills having grievonsly disappointed the high hopes which were at first entertained of it. A chill being a fall of the temperature below that needed for the complete liquefaction of the slag, which requires, according to Plattner, about 1800' C., one would suppose that the chief thing to be accomplished in curing it would be to raise the temperature in the crucible of the furnace. The most obvious ways of doing this seem to be to raise the temperature of the blast, and to increase the amount of fuel in the crucible itself. Simply increasing the rate at which the blast enters the furnace, if carried beyond a certain point, should lower the temperature in the crucible. The existence of a chill shows that the fuel is arriving too slowly at the tuyeres. If air be introduced so rapidly as to he in excess of that required for the combustion of the fuel, all that excess will simply lower the temperature around the tuyeres, carrying the region of intense heat upwards, and weakening its intensity by increasing its size. Up to a certain point, increasing the rate of introducing the blast will increase practically pari passu the rate at which the fuel reaches the tuyeres. But when mechanical obstructions, which so often accompany chills, retard the descent of the fuel, there must be a point beyond which this does not hold good, and beyond which farther

Jan 1, 1883

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith' have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By L. Ibagos S., T. Balberyszski

The volumetric flow rate and the initial concentration of the copper sulfate solution influence the rate of reaction and, hence, the precipitation efficiency in a continuous launder cementation system. Using a model of such a system it was found that the precipitation efficiency is related to the two process parameters by the approximate expression [ log [1-n] = -[0.072 co 2.91 e – 0.511c o Q 1.15 ] N Q] where c is the initial concentration, Q, is the volumetric flow rate and N is the number of launders in the system. This expression agrees with an equation developed for the rate of the cementation process if it is assumed that the exponential factor represents the change in the surface area with concentration and the exponents 2.91-and 1.15 relate the hydrodynamic conditions and the surface concentration to co and Q. The experimental results are used to determine the values of a Precipitation Coefficient for any volumentric flow rate and initial concentration of solution. Knowing the Precipitation Coefficient, the total volume of launders that will result in a given precipitation efficiency can be calculated. It is established that maximum precipitation efficiencies are obtained for initial concentrations between 6.0 and 7.0 gpl and volumetric flow rates of approximately 350 m3 /hr Good agreement between calculated and actual launder volumes is obtained for a number of industrial operations for which a comparison is made.

Jan 1, 1973

By K. R. Janowski, A. B. Chase, E. J. Stofel

Ruby crystals of exceptional optical quality have been grown from fluxes composed of Bi2O3 + PbF2 or Bi2O3 + BiF3. Careful control of growth conditions was required to minimize the number of growth defects consisting primarily of dislocations, occluded flux, and growth twins. Slow growth rates coupled with the addition of small amounts of La2O3 as a flux dopant were helpful in producing nearly perfect crystals. Chromium concentrations up to 1 pet were incorporated into these crystals without adversely affecting their perfection. Crystals up to 10 mm in diameter having as few as one to ten dislocations per crystal were typical of those produced under optimum growth conditions. Under these same conditions the occlusions were eliminated, and growth twins were either eliminated or reduced to one to three twin boundaries per crystal. INTEREST in the nature of lattice imperfections produced during the growth of ruby crystals (Al2O3-corundum structure) has been stimulated recently by the need for ruby lasers of good optical uniformity. As a result, ruby crystals grown by the flame-fusion (Verneuil) process have been studied in detail and have been found to contain high densities of dislocations (106 to 107 dislocations per sq cm) and mosaic structures that impair their optical quality.'-3 Attempts to improve the quality of Verneuil-grown crystals by controlling the growth variables have not been entirely successful. On the other hand, rubies grown by the flux process have received little attention even though their more nearly equilibrium growth conditions suggest that they would have fewer growth defects. Nelson and Remeika have shown recently that small flux-grown rubies can indeed be made into very low-loss lasers. However, they did not report information on crystalline imperfections in these crystals.4 Stephens and Alford have reported briefly on defects found in a flux-grown corundum crystal but they neither described these defects in detail nor related them to the method of growth.5 The present investigation was undertaken to establish the relationship between growth conditions and crystalline perfection of flux-grown rubies, sapphires, and other crystals of the corundum family. EXPERIMENTAL PROCEDURE The corundum crystals used in this study were grown by slowly cooling solutions of A12O3 in molten-salt solvents of PbO + PbF2, Bi2O3 + PbF2 or Bi2O3 + BiF3. The materials employed were Linde A (a Al2O3 powder) with reagent-grade chemicals as solvents. Some of the solutions also contained small additions (1 pet or less) of one or more of the transition metal elements chromium, manganese, iron, and titanium as crystal dopants. La2O3 was added to some of the solutions to alter the growth habit of the crystals. The La2O3 promoted the occurrence of growth facets parallel to (0112) and {1011} planes, where the indexing system is the morphological system described in detail by Kron-berg6 and used throughout this paper. The melts from which the crystals were grown were prepared by mechanically mixing the various constituents and placing them in platinum crucibles. The covered 50- and 100-ml platinum crucibles were heated in muffle furnaces at 1250°C for short periods of time (1 to 4 hr) and then program-cooled at either 2° or 4°C per hr to 1000°C. At this lower

Jan 1, 1965

By Joseph S. Malesky

The discovery and development of explosives mark one of the most important findings in the history of civilization. Without explosives our vast economic enterprise concerning the mining of coal, copper, iron, aluminum, and various other ores could not function. Explosives are used in all kinds of construction works, in the razing of old buildings, blasting of trenches, driving of tunnels, and in many other instances common to our everyday life. For these reasons explosives are rightfully referred to as the forerunner of progress. An explosive may be defined as a substance (usually a mixture) that, when flame or shock is applied, yields readily to rapid combustion or oxidation, accompanied by the formation of such relatively large quantities of gases as to produce much violence and pressure which, in turn, react against their surroundings and cause what is termed an explosion. By their very nature the action of explosives is destructive and disruptive of adjacent materials. Decomposition of explosives can occur through deflagration, which is rapid burning or combustion, as in the case of black powder, or through detonation, which is an almost instantaneous disruption, as in the case of dynamites and blasting agents. HISTORY OF BLASTING WITH EXPLOSIVES At one time workmen obtained stone blocks for building by grooving the rock with crude picks, driving wooden wedges into niches in the rock, and pouring water on the wedges; the swelling of the wood forced out the blocks. As late as the 17th century, fires were placed against the face of rock to crack it, and water was sometimes dashed on the heated rock to shatter it by sudden cooling. The progress of our country is synonymous with advancement of the improved manufacture and extended use of explosives. Coal had been

Jan 1, 1981

By T. D. Tiemann

The chemical and mineralogical composition of Caribbean bauxite ores are described. Extraction of alumina by several processes from both Haiti and Jamaica bauxites is discussed and data presented. IMMENSE deposits of bauxite occur in the Caribbean islands of Hispaniola and Jamaica in the high plateau lands and have been excellently described by 0. C. Schmedeman.' The bauxite occurs as deposits in catchments or etched depressions in Tertiary limestone believed to have been deposited in the Eocene and Oligocene periods.' In appearance both the Haiti and Jamaica bauxites resemble a relatively high iron clay and have indeed been mistaken for such.' They are very soft and friable and disperse readily on vigorous agitation in water. The color range in general is light brown to red. Chemically, the outstanding characteristic of the bauxites is the low silica and high ferric oxide content. The extremely low silica makes them particularly valuable for the production of alumina in the Bayer plant since silica is responsible for the loss of both alumina and soda chemically combined as XNa,OYSiO2,ZAl2O2. The ferric oxide, only traces of ferrous iron are present, offers no interference in the production of high grade alumina. Typical oxide analyses of three types of ore are given in Table I2 and a list of the elements occurring in spectrographic quantities in Table 11." The size of the individual particles in the ore makes successful petrographic examination extremely difficult. The ores contain some relatively coarse grains of heavy minerals such as ilmenite, magnetite, and rutile, but other than occasional crystals of a few microns, the greater portion of the minerals are submicroscopic in size and approach colloidal dimensions. The mineralogic composition of the ores has been investigated by X-ray and differential thermal analysis.' These investigations indicate that the predominant mineral phases present are gibbsite (A1203.3H2O), boehmite (Al2O3.H2O), hematite (Fe2O3), and goethite (Fe2O3-H2O). There is no evidence of the occurrence of diaspore (Al2O3.H2O) in either the Haiti or Jamaica ores, but some type of "amorphous" alumina may be present in some of the bauxites of Jamaica." The temperature stability regions in the alumina-water system have been investigated and are given in recent literature. In the temperature range where the hydrated forms are stable, as determined by hydrothermal bomb methods," ibbsite is the stable phase to 155°C (311°F), boehmite from 155°C (311°F) to 280°C (536oF), and diaspore from 280°C (536°F) to 450°C (842°F). Although quite similar in many characteristics, the Haiti and Jamaica ore show a divergence in mineralogic composition that is reflected in the extractability of the alumina described in later paragraphs. Two principal differences occur in mineralogic composition. The iron-bearing mineral in the Haiti ores is predominantly hematite, while in the Jamaica ores goethite is predominant.4 Directly related to the extraction of alumina are the two minerals, gibbsite and boehmite. Boehmite is relatively high in the Haiti ores and in some of the less soluble Jamaica ores, while gibbsite predominates in the ores in Jamaica amenable to the American Bayer process of extraction. Pedersen and Related Processes In general, all processes for the extraction of alumina involving sintering or fusion of bauxite ores with limestone, soda ash, or a combination of limestone and soda ash followed by leaching, are based on the formation of alumina compounds that. yield alumina soluble in the subsequent leach. The principal idealized reactions in respect to alumina and silica for the three types of processes are as follows: Soda Ash Sinter: A12O3 + Na2CO3 = Na2O-Al2O, + CO2 SiO2 + Na2CO3 = Na2O . SiO2 + CO2 A12O2 + SiO2 + Na2CO3 = Na2O.Al2O8. SiO2 + CO2 Leach (with excess water): H2O + Na2O-A12O3 = 2 NaOH + A12O3 (insolution) H2O + Na2O-SiO2 = 2 NaOH + SiO2 (in solution) Soda Ash— Limestone Sinter: Na2CO2 + A12O3 = Na2O.A1203 + CO2 2CaCO3 + SiO2 = 2CaO . SiO2 + 2CO2 Leach (with excess water): Na2O' A1208 + H2O = 2NaOH + A13O3 (in solution) These latter reactions are the basis of the sinter process currently used for the recovery of soda and

Jan 1, 1952

By A. L. Jr. Pozzi, A. O. Garder, D. W. Peaceman

A new numerical method is proposed for the solution of multidimensional miscible displacement problems. Besides the usual stationary grid associated with numerical procedures, the method uses moving points for which positions and concentrations are computed each time step. Based on the method of characteristics for treating combined transport and dispersion, the method applies equally well to any number of dimensions and, in contrast with other numerical procedures, properly takes into account the physical dispersion, no matter how small. Extensive tests show that accurate solutions of one-dimensional problems can be obtained over a wide range of values of the dispersion coefficient, including zero. They also show that the moving points do not need to be uniformly spaced, and that increasing the number of moving points beyond 2/grid interval does not significantly improve the accuracy of the solution. Two-dimmsional calculations using the new method were carried out to simulate laboratory model displacements in which gravity caused overriding of solvent. Good agreement between observed and computed profiles and measured and computed concentrations of produced fluid was obtained for a viscosity ratio of 1.89; at higher viscosity ratios, fair agreement was obtained Computed results were found to be significantly affected by vertical dispersion, and negligibly affected by dispersion in the direction of flow, in agreement with conclusions based on experimental observations. INTRODUCTION Although miscible displacement processes are potentially of great economic significance, limited progress has been made in developing mathematical methods for predicting the outcome of a solvent flood. Because of the complexity of the partial differential equations which describe multidimensional miscible displacement, numerical methods are a natural approach to their solution. The task of finding suitable numerical approximations to one of the partial differential equations, which involves both dispersion and convective transport, has been particularly difficult. Dispersion in the absence of transport is described by the heat flow equation, a second-order equation of parabolic type. This equation has been very successfully treated by numerical methods. Transport in the absence of dispersion is described by a first-order equation of hyperbolic type. This equation has been treated numerically with some success in one dimension, both by Lagrangian and Eulerian techniques, 1.2 but extension to two or more dimensions has not been satisfactorily accomplished. Usually one of two things happens: either the numerical solution develops oscillations or it becomes smeared by artificial dispersion resulting from the numerical process. When transport and dispersion are considered simultaneously, this numerical dispersion may dominate the low physical dispersivicy that generally characterizes miscible displacement. Stone and Brian2 have developed a new difference equation for treating combined transport and dispersion in one dimension. By suitable choice of certain parameters, they succeeded in markedly reducing both oscillation and numerical dispersion. However, a satisfactory extension to higher dimensions has not yet been found. Peaceman and Rachford3 presented a centered-in-time and centered-in-distance difference equation combined with a 1,transfer of overshoot" procedure which was demonstrated to work well in one dimension. The technique was applied to the two-dimensional miscible displacement problem, but subsequent calculations with zero dispersivity showed little change in results compared with the calculations they presented. This indicates that their method involved a numerical dispersion of the same order as the physical dispersion. The present paper describes an alternate method for solving the combined transport-dispersion

Jan 1, 1965

By W. J. Reagan

THE problem of increasing output and decreasing percentage of rejections is a vital one in the manufacture of steel of any kind. The making of basic open-hearth steel for use in rolled steel wheels, tires for locomotive and car wheels, and forgings of various kinds, is a highly specialized industry. The increase in weight of railway rolling stock of all kinds, and the high speed that the public demands of transportation facilities, make it imperative that steel for use in this class of material shall be of the highest quality obtainable. During the past few years it has been the writer's good fortune to have opportunity-to study the defects in basic open-hearth steel, and also the results obtained by various changes in open-hearth practice, on such defects. The opportunity for study and the details available are rarely found in the manufacture of steel of any kind. It seems reasonable to assume that many of the results determined here can be applied to the production of steel of other types with a decided improvement in quality, a decrease in the percentage of rejections and an increase in output. All of the material described is basic open-hearth steel with the following range of analysis: carbon, 0.50 to 0.85 per cent.; phosphorus and sulfur, 0.04 coax.; silicon, 0.15 to 0.35; manganese, 0.50 to 0.75. All of this material is bottom-cast, therefore tapping and pouring temperatures are higher than in top-cast production. Ingots used in this type of work are of standard length with varying diameters. The ingot is known as duodecagonal, or twelve-sided. The standard body length is 88 in. and the hot top length, 14 in. Fig. 1 shows a typical ingot of this type. The diameter varies from 13 to 30 in. Ingots for special forgings, which cannot be made in molds of standard size, are made in molds of various sizes and designs. These ingots are sliced cold, into blocks of various lengths, depending upon the weight of the forging to be made. Fig. 2 shows the ingot-after coming from the slicing lathe. Just sufficient metal remains between blocks to hold the ingot in one piece while it is being removed from the lathe; then steel wedges are inserted between the blocks and the blocks are broken apart. This affords abundant opportunity for inspection, as the interior of the

Jan 1, 1930

By Sherwin F. Kelly

NEW trend in geophysics has been uncovered in these depression years, made evident through the thinning cloak of commercial activity, which, in better times, would have completely obscured it. I refer to the increasing use of these methods for geological investigations by federal and state geological surveys. This is a trend that has been gathering momentum not alone in the United States, but abroad as well. Thus, in Poland, the Geological Survey has been playing an increasing role in geophysical work since 1927, and now has- its own geophysical department. The government petroleum producing organization of Argentina has its Geophysical Commission; Brasil boasts a completely equipped geophysical department in its Mineral Production Service; the government of Chile has contracted with commercial companies for geophysical surveys; Peru is planning an intensive program of geophysical prospecting in its petroliferous regions; and Canada has, for several years, cooperated with

Jan 1, 1935

By H. N. Hall

Various factors must be considered in an engineering evaluation of gravity-drainage reservoirs. Among these are: (1) the effect of producing rate on total oil recovery; (2) the effect upon well productivity and ultimate recovery of the pressure level maintained during the producing life of the reservoir; (3) the economic advantage of full or partial pressure maintenance; and (4) estimate of the rate of gas production and injection and the possible purchase of gas under conditions of full pressure maintenance to ascertain compressor facilities needed. All of these factors can be evaluated only when a reliable method is employed for determining reservoir performance in gravity-drainage reservoirs. The purpose of this paper is to present a general method for calculating the performance of a gravity-drainage reservoir. This method is applicable for conditions of complete pressure maintenance, partial pressure maintenance and normal pressure depletion. Provisions are made to take into account variations throughout the reservoir of reservoir configuration, changes in permeability and fluid composition. Based on the method presented in this paper, an IBM 650 computer program has been developed. The past performance of an actual gravity-drainage reservoir producing under conditions of declining pressure and no gas injection was duplicated using this program. INTRODUCTION In tilted reservoirs the production of oil is influenced by drainage of oil from upstructure to downstructure locations. When this downstructure drainage of oil is sufficient to cause effective segregation of the gas and oil in a reservoir, the reservoir is usually classified as a segregation drive or gravity-drainage reservoir. (Discussion will be restricted to gravity-drainage reservoirs which have no encroachment of edge water.) The important feature in gravity-drainage reservoirs is the density difference between reservoir oil and gas. These phases tend to segregate in the reservoir with the result that in the gas cap the oil saturation is maintained at a higher level by drainage of oil from the gas-cap area. Oil can be produced from the oil zone at a low gas-oil ratio and reservoir energy is thereby conserved. The standard material balance in not adequate for predicting gravity-dramage reservoir performance because it does not take into account the difference in saturation above and below the gas-oil contact. Several authors'.' have presented methods for calculating the performance of gravity-drainage reservoirs in which reservoir pressure is maintained constant by gas injection into the gas cap. Using some simplifying assumptions, these methods can be employed with a desk calculator to give acceptable results. The problem of predicting the performance of gravity-drainage reservoirs under the conditions of declining reservoir pressure is many time more complex than that of constant pressure. fierefore, attempis to develop a method suitable for desk calculation have required excessively simplified assumptions. In the past several years, highspeed digital computers have become more widely available for reservoir engineering problems. These corn puters are well suited to problems such as the prediction of the performance of gravity-drainage reservoirs with pressure decline. Many of the simplifying assumptions necessary for hand computation can be eliminated so that a realistic approach to the gravity-drainage process can be made. CONCEPTUAL PICTURE OF OIL MOVEMENT IN GRAVITY-DRAINAGE RESERVOIRS Before attempting to develop an analytical treatment for conditions occuring in a gravity-drainage reservoir, a concept should be formed concerning the movement of fluids in the reservoir as oil is produced. A review of the literature'.' shows that it is customary to classify gravity-drainage operations into two categories—(1) with complete pressure maintenance, and (2) with declining pressure. The same line of reasoning will be followed in presenting the concept of the movement of fluids in the reservoir because it is easier to visualize the movement of fluids under conditions of complete pressure maintenance. After discussing complete pressure maintenance, an analogy will be made between that and the case of declining pressure. It should be kept in mind throughout that the final aim for the problem of solving gravity-drainage performance with digital computers will be to develop a general program for any kind of gravity-drainage reservoir. COMPLETE PRESSURE MAINTENANCE One feature which is generally common in gravity-drainage reservoirs is a gas cap located at the top of the structure. This is shown in Fig. 1(a). Fig. l(b) shows oil saturations that might occur through the reservoir. In the gas cap, oil saturation is lower than

By A. W. Furbank

IN reviewing the aerial cameras produced in different countries, it becomes apparent that in nearly all of them an attempt has been made to secure the greatest possible angle of view. This angle, of course, is determined by the objective. The objectives most commonly in use in aerial cameras have a maximum angle of 65°. The objective developed for this new Zeiss camera combines freedom from distortion and brilliant definition, with an angle of 95°. Aerial mapping, it is claimed, has been placed on a different economic basis, and new possibilities presented, par-ticularly in connection with automatic stereoscopic plotting instruments, to which some short references are made. One way of enlarging the angle of view is to couple several instruments with their axes convergent, thereby producing a multilens camera. Typi-cal of cameras of this sort in the United States is the Bagley four-lens camera, which later was developed into the five-lens camera (T3-A) of the U. S. Air Corps. More recently, in order to get away from the unfavorable Maltese cross image field of the five-lens camera, and to obtain a more practical form, two five-lens cameras were combined. By using them in tandem and rotating them by 45° relatively to each other, a ten-lens camera was produced, covering an octagonal ground area, with a total angle of view of 140°. Similar designs have been evolved in other countries. In all of them, however, a number of difficulties have arisen, quite apart from their large weight and high cost. Because of their complex mechanism, numerous shutters and magazines, and the high precision with which these parts must be interadjusted and synchronized, these cameras are far from dependable. Moreover, a multilens camera by itself does not yet constitute a complete outfit for producing pictures suitable for photogrammetric survey. Because all the component pictures, except the central one, are obliques, it is always necessary to employ rectifying apparatus which transforms the marginal views to the perspective of the central one. In multilens cameras with many individual magazines, it is not convenient to

Jan 1, 1938

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

WE the undersigned, being all persons of full age and citizens of the United States, and a majority residents of the State of New York, desiring to form a corporation pursuant to the provisions of the Membership Corporations Law for the purpose of incorporating, 8s provided in Section 5 of Article I. of said law, the existing unincorporated association known as American Institute of Mining Engineers, do hereby make, acknowledge and file this Certificate for that purpose, and do Certify as follows: I. That the American Institute of Mining Engineers is an unincorporated association organized and existing with the object of promoting the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by means of meetings for social intercourse and the reading and discussion of professional papers, and to circulate by means of publications among its members and associates the information thus obtained. II. That the persons duly appointed or designated to manage the affairs of said association are designated by the rules thereof Members of its Council; that the under- signed are all members of said Council as the same was constituted on the 29th day of December, 1904.

Jan 1, 1932

By George Kunz

(Butte Meeting, August, 1913.) . THE manifold inconveniences resulting from the absence of a uniform standard of mass for determining the weight of precious stones have long been obvious. This lack has been keenly felt in commercial transactions, and those who have devoted time and research to the study of historic diamonds and precious stones have had frequent occasion to deplore the absence of such a standard in the past. In a paper read in Chicago in 1893, before the International Congress of Weights and Measures, held in connection with the World&apos;s Columbian Exposition, the writer suggested dividing the carat into 100 parts, and constituting a standard international carat of 200 mg. ; that is, 5 diamond carats or 20 pearl grains to a French gram, making 5,000 carats or 20,000 pearl grains to a kilogram. He also called attention to the fact. that while this would depreciate the present diamond carat or pearl grain only about 2.5 per cent., it-would abolish the troublesome discrepancies between the various carat-weights now in use, and could be easily explained and understood everywhere.1 The subject of the various diamond carats, their incongruity, and the resulting confusion as to the correct. weights of historic gems when definite records of them are searched for, has been fully treated by me in an extensive study of this subject in The Book of the Pearl.2 To the earnest and unremitting efforts of C. E. Guillaume, Director of the Bureau Internationale des Poids et Mesures at Sèvres, is largely due the eventual success of this eminently desirable reform, which he has constantly urged both by articles on the subject and by addresses delivered in Paris before the International Committee for Weights and Measures.2

Jan 7, 1913

By Renato G. Bautista, Theodore D. Tiemann

A kinetic study of the hydrogen reduction of taconite from the Wisconsin Gogebic range was made over the temperature range from 500° to 1000°C on eleven size fractions from 4 to 150 mesh. Two stages of reduction were observed, a rapid initial reaction followed by a slower reaction presumably taking place at an internal receding FexO-Fe interface. Calculated mean activation energies for the two reactions were 7800 and 14,600 cal per mole respectively. In recent years there has been an increased interest in the direct reduction of iron oxide ores to metallic iron by means of gaseous reducing agents such as hydrogen and carbon monoxide.1,2 These investigations have been motivated by the desire to develop a process that will by-pass the blast furnace in the production of steel. The majority of these processes have been developed to produce metallic iron by direct reduction from high-grade iron oxide ores.3"5 Very little work has been done on the low-grade siliceous iron oxide ores.6"8 The work reported here is directed principally towards the fundamental aspect of the reduction reactions of siliceous iron oxide ores, since the practical aspects of the gaseous reductant process were discussed previously. The ore used in the investigation was obtained originally from the United States Bureau of Mines10 trench sample of the Yale member of the Wisconsin Gogebic range iron formation. The Yale taconite has an average analysis of 28.2 pct Fe and approximately 50 pct SiO2. Chemically, these nonmagnetic taconites contain on the average about 53 pct silica and 30 pct Fe. An average analysis calculated fron the USBM10 figures for a composite of the five members (Norrie, Plymouth, Pence, Pabst, and ale) of the iron formation is given in Table I. Mineralogically, based on previous X-ray diffraction and other studies, the principal minerals are hematite (Fe2O3), geothite (Fe2O3.H2O), and quartz (SiO2). Minor amounts of iron containing silicates, siderite (FeCO3) and magnetite (FeO. Fe2O3) are present.10,11 The iron minerals and the quartz are finely disseminated requiring extremely fine grinding for liberation. For the experimental work, the ore sample was screened into a number of size fractions, the analyses and densities of which are given in Table II. EXPERIMENTAL PROCEDURE The reduction experiments were carried out in a 24 in. by 2 in. ID nichrome-wound vertical-tube furnace mounted on a stand. A 1 1/2 in. OD zirconium-oxide combustion tube was used inside the furnace to contain the atmosphere. To the top of this combustion tube was joined a pyrex ground-glass joint to which was attached a glass bulb with a small (1.0 mm) opening at the center, and with two outlets controlled with a stopcock on each side. A pyrex-glass joint with connections to three stopcock joints for introducing hydrogen, nitrogen, and mixtures of hydrogen and nitrogen gas was joined to the tapered bottom of the combustion tube. The sized ore fractions were contained in a 1 in. diameter by 1 1/2 in. 150-mesh nickel screen basket. The basket was suspended in the furnace from a balance by means of a supporting nickel wire which hung freely inside the combustion tube. The furnace temperature was controlled by a Leeds and Northrup Speedomax Type G controller, connected to a chromel-alumel thermocouple placed

Jan 1, 1962

By Hsun Hu, R. S. Cline

The effect of rate of deformation on texture formatiotz has been studied with cube-oriented single crystals of 3 pct Si-Fe, compressed 80 pct at two widely different rates. Compression at a low rate (crosshead speed, 0.1 ipm) produces large orienta-tional changes and coarse deformation bands, whereas little change in orientation is observed, particularly at the surface of the crystal, when compressed at a high rate (impact velocity, -500 ips). Thin plates of mechanical twins are produced at the high rate, but their contribution to the deformation texture is practically negligible. The crystal deformed at a high rate has a lower hardness and a more uniform dislocation structure and is morc resistant to recrystallization. There is also a dilference in the recrystallization texture between the slowly and rapidly compressed crystals. These results indicate that plastic flow is less "turbulent" at high strain rates than at low strain ratcs. THE behavior of metals under high-speed deformation has been the subject of wide study in the past decade. Most of these works were concerned with mechanical properties during testing at high rates of loading, the resulting structures, and the theoretical aspects of the observed phenomena. The present status of knowledge and research activities in this field has been documented in recent publications.17&apos; There is, however, very little information available in the literature concerning the effect of high-speed deformation on the texture formation in metals. The possibility of an effect of rate of deformation on texture is suggested by the microstructural differences observed between normally and very rapidly deformed samples. Aside from the strong tendency for twinning (and phase transformation in certain metals) in high-speed deformation, the slip-line patterns and the dislocation configurations show marked differences as a result of large differences in the strain rates. For instance, in mild steel in static and dynamic compression, Campbell and co-worker3,4 observed that coarse slip occurred on several systems in specimens deformed at normal strain rates, whereas specimens deformed rapidly showed only fine slip on fewer systems, the slip-line pattern being very similar to that in specimens deformed at low temperatures and at normal strain rates. The absence of multiple slip was also noticed by Dieter5 in shock-loaded nickel. The dislocation configuration in an iron shock loaded at 70 kbar pressure was shown by Leslie et al.6 to be similar to that produced by light rolling at low temperature—the dislocation lines were mostly straight and uniformly distributed. These observations suggest that the mode of deformation at high strain rates is notably different from that at low strain rates. Consequently, the nature and the extent of lattice reori-entation during deformation should also be different. This investigation was undertaken to test this idea. MATERIAL AND METHOD The remaining part of a single-crystal ingot of a 3 pct Si-Fe alloy,* prepared for an earlier investi- gation,1 was used in the present studies. Specimens 9/16 in. square and 0.365 in. thick were cut from this ingot with (001) planes parallel to the square surfaces, and the [loo] and 1010] directions parallel to the edges of the specimen, within ±1 deg. These machined crystals were etched to remove distorted metal, and annealed at 1300°C for 24 hr in a purified helium atmosphere. The annealed crystals had a hardness of 161 Dph. The crystal orientation was rechecked with X-ray back-reflection techniques. In high-strain rate experiments the crystal was compressed in a Dynapak machine to approximately 80 pct reduction in thickness (from 0.360 to 0.070 in. with an impact velocity of -500 ips). Thus, the duration of loading was approximately 6x 10-4 sec, and the average strain rate was about 103 sec-1. As a result of this rapid, severe deformation, the specimen became a roughly circular thin disc. The original shape of the crystal, however, could still be recognized by a diffusely outlined square area in the center of the disc. For compression at a low speed, the crystal was deformed in a universal testing machine at a rate of crosshead movement of 0.1 ipm. Compared with

Jan 1, 1965

By B. S. Norris, Charles R. Austin

The stresses which initiate deformation processes in metals are fundamentally important in the study of the mechanical properties of metals. A point of inflection in the load-elongation curves obtained for single crystals&apos; has been rather too readily interpreted as a true yield point, and the critical resolved shearing stress on the plane of slip taken as a material constant. Even early work showed that the stress at this point varies with rate of loading, but it has not been generally appreciated that creep tests under static loads alone are suited for determining the existence or nonexistence of a yield point.* It has now been shown by Miller that single crystals of zinc3 when loaded statically begin to yield at loads too small to measure; as a result there is no case now known, apart from that cited in the present paper, in which a true critical stress for yielding has been demonstrated for single crystals of metals. The case of iron has especial interest: the existence of an upper and lower yield point and of an elongation at the yield point in ordinary iron and steel marks this substance as unusual, though the effects have been found to a very minor degree in other metals and alloys. $ Most alloys do not show such marked phenomena when appreciable yielding begins, and accordingly modern practice is to speak of the yield strength of such materials, a stress read from the load-elongation curve after elongation has begun, rather than yield point. The special behavior of iron suggests that it is more likely that single crystals of iron should have a true yield point than other metals. The study of the mechanical properties of metals and alloys requires a determination of the crystallographic mechanism of deformation, wlletller deformation proceeds by slip, twinning, or cleavage, or a combination of these, and a determination of the stresses that induce these modes of deformation. With this information, a study of the rates of work-

Jan 1, 1938