Search Documents

By Edward B. Cook

INTRODUCTION. THE installation of the Gayley Dry-Air process appealed specially to the management of the Warwick Iron & Steel Co., for the. reason that for fifteen years records had been kept at the works of the company, showing the amount of water entering the furnace in the form of aqueous vapor, and careful observations had been made of its effect upon the working of the furnace. Some years had proved much worse in their effect than others, on account, not only of excessive moisture, but also of great variation in the moisture from day to day, and sometimes within a few hours. It had been found impossible to. make a satisfactory percentage of high-silicon foundry-iron in summer, even on high fuel; and for some years the endeavor had been made so to arrange the sales that, during July and August, only a small percentage of the iron produced would be required to carry more than 2 per cent. of silicon. Our larger furnace, running on basic iron, year after year, produced in February a tonnage 20 per cent. higher than in August, on a much lower fuel-consumption, while, at the same time, the summer months were marked by ? messes," tuyeres closed by slips, and other irregularities, constituting serious additional business losses. It will be easily understood, therefore, that the records made at the Isabella furnace after the installation of the dry blast in 1904 possessed special interest, and were closely watched by us. On the basis of our own experience, we argued that if the moisture could be kept low, and also uniform, the cost of installation would be more than justified. The subject was brought before our Board of Directors in the fall of 1905; and in the spring of 1906 it was decided to install a plant of sufficient capacity to treat 70,000 cu. ft. of air per min., an amount

Nov 1, 1908

By P. A. C. Wilson

Instantaneous outbursts of carbon dioxide in coal mines have occurred in Germany only in one part of the Waldenburg-Neurode mining district.' This mining region comprises the northeastern fold of the "Innersudetian" coal basin. The basin (Fig. 1) is in the form of a geologic trough approximately 60 km. (37 miles) long and 30 to 35 km. (19 to 22 miles) broad and is enclosed on three sides by ancient truncated mountain ranges—the Riesengebirge, the Bober-Katzbachgebirge and the Eulenge-birge. Only the southeastern part of the trough is not enclosed by mountains of older rock formation. The floor of the basin before the building up of the coal measures was formed on the western, northwestern and northeastern borders by the material from Archean rocks (gneiss and mica schists); in the northern part over this was deposited the Silurian formation. The carboniferous period is represented both by the Lower ("kulm") and Upper Carboniferous, with an unconformity between the stages; that is, the kulm was tilted up and partly eroded before the Upper Carboniferous was deposited. The kulm is a salt-water formation (with marine fauna) but Upper Carboniferous rocks are nonsaline water deposits, with fresh-water flora only. The Lower Silesian coal measures were thus formed in a lime basin fed by the running water coming down from the mountains. As already indicated, the bottom series of the Upper Carboniferous formation, termed "Waldenburg strata" were laid down unconformably on the Lower Carboniferous. Over the Waldenburg strata there are the "Weisstein strata," an intermediate barren stage without coal beds, 400 to 500 m. (1300 to 1600 ft.) thick. Another unconformity followed, which is overlain by the '(Saarbrucken" series, which contain the upper coal measures, and the ('Ottweil" strata. In the last named, it is only on the southwestern fold that beds of coal are developed.

Jan 1, 1931

By C. Norman Cochran, James L. Brandt

ALTHOUGH gas in aluminum and its effect on aluminum products have been the subject of a number of papers, not many quantitative determinations of the hydrogen content of solid aluminum and its alloys have been recorded in the literature. For solid aluminum samples, four investigators have reported hydrogen contents which appear reasonable compared with the hydrogen solubility of 0.7 ml per 100 g, STP, in molten aluminum at 660°C established by Ransley and Neufeld' and verified by Opie and Grant' and Ransley and Talbot. Sloman," who used a vacuum fusion procedure, reported the hydrogen content of some high purity aluminum as 0.66 ml per 100 g, STP. Griffith and Mallett, employing the tin fusion method, reported the internal hydrogen content of six different aluminum alloys as ranging from less than 0.1 ml per 100 g, STP, for 1100 alloy to 0.7 ml per 100 g, STP, for 4043 alloy (previously 43S, a 5 pct Si alloy). Eborall and Ransley," using a solid extraction of the gases at 600°C, reported hydrogen contents ranging from 0.1 ml per 100 g, STP, to 1 ml per 100 g, STP. Ransley and Talbot reported that several thousand analyses on 99.2 pct and higher purity aluminum as well as Duralumin type alloys indicated hydrogen contents ranging from 0.1 ml per 100 g, STP, to 0.5 ml per 100 g, STP.

Jan 1, 1957

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By G. W. Jones

THIS paper describes experiments in which eight test samples of gelatin dynamite were fired in three different types of apparatus and the quantity and composition of the gaseous products of detonation determined. The special dynamites were so prepared that the oxygen balance of the samples varied from -35.0 to +6.0 g. per 100 g. of explosive, including the wrapper. By means of this graded series of explosives, the relation between oxygen balance and gaseous products of detonation could be studied explicitly. The effect of varying oxygen balance on explosive strength has been discussed in another paper.1 The apparatus employed in the work described in the present paper included (1) the Bichel gage, a steel bomb of 15-1. volume; (2) the Crawshaw-Jones confined detonation apparatus, a steel cannon from which the explosive is fired into a pipe of 90-1. volume; and (3) the Hercules tank, an apparatus in which the explosive is confined in a quartz block which is placed in a steel tank of about 4500-1. volume. A full description of the apparatus is given later. VARIABLES AFFECTING COMPOSITION OF DETONATION PRODUCTS The character of the detonation products of commercial explosives is governed in part by the same factors that affect the combustion products from explosive mixtures of air with gases or vapors. In either case, combustible materials-namely, carbon, hydrogen, and sometimes sulfur-are present and combined variously. In an exploding gas mixture the combustibles are oxidized by oxygen in the admixed air, whereas with explosives the necessary oxygen is provided by oxygen-carrying materials in the explosive ingredients.

Jan 1, 1928

By Thomas T. Read

The cost of labor turnover in industry is so large as to justify the adoption of almost any means to bring about its reduction. Intensive study has shown that faulty methods of hiring and discharging men is the most important factor in labor turnover. Complete control over hiring and discharging by the foreman is a relic of outgrown industrial conditions; centralized hiring permits this work to be put on a scientific basis and also does away with many serious evils that cannot, otherwise be reached. Centralized hiring does not impair the authority of the foreman; he hires his men from the employment office and discharges them back to it, instead of from and to the street. The employment manager, being a direct representative of the employer, tends to restore the former relation of direct intercourse between employee and employer that was helpful in avoiding friction between them. Being a specialist,, he is able to bring special knowledge and skill to bear upon the task of selling employment in his concern to desirable workmen; he is also able to give the foreign workman the special attention he requires. Employment managers have been used for the past few years by a number of large organizations, a few of which are engaged in the mining and rnetallurgical industries. They have invariably reduced labor turnover, in some cases to as little as one-tenth of what it had been. So great a reduction is due in part to other changes made in the light of the data made available by scientific study of the labor problem. In my former paper on personnel work' I advocated the more general use of the employment manager in mining and metallurgical enterprises as a means of reducing labor turnover. The form of organization recommended seems not be to understood by all, and I have requested the privilege of explaining it at greater length, since it is perhaps the most important factor of all in personnel work, and has a vital influence on the cost sheet of every industrial enterprise.

Jan 1, 1918

During February there will be a meeting of the Committee on Technical Nomenclature of the Society for the Promotion of Engineering Education and representatives of the various engineering societies, to do the preliminary work necessary for the adoption of uniform lists of technical symbols. At this time it is expected that lists of symbols in general use throughout the country will be presented and the symbols most generally used will be recommended for adoption.

Jan 2, 1919

By H. C. Chang, N. J. Grant

Creep of very coarse grained, high purity aluminum was studied at 400° to 1100°F with an initial stress range of 50 to 1200 psi. The process of boundary sliding and migration was studied. The driving force of boundary migration under creep conditions is shown to be a combination of strain energy migrationand surface energy. A theory is presented regarding the strainenergyrole the grain boundaries play under creep conditions. From this thetheory intercrystalline failure of commercial alloys can be explained. Also from this theory an optimum grain size should exist for good high temperature properties of high purity materials. IN the investigation of the creep of very coarse grained, high purity aluminum previously reported,' the cyclic nature of the process of grain boundary sliding and migration has been established by microscopic observation of the actual creep process as well as metallographically. It was also substantiated by measuring localized strains across the grain boundaries. In addition, it was shown how extensive subgrain and fold formation may result from boundary sliding and how the slid grain boundary may become sharply wavy as a result of subgrain formation. Since the publication of those results, additional information on the process of grain boundary sliding and migration has been obtained. It is the purpose of this paper to report on the direction and driving force of boundary sliding and migration, the effect of grain size, and the effect of temperature. Finally the effect of decreasing purity (alloys 2s and 3s) on the process of boundary sliding and migration is noted. From these results, an explanation is presented for the intercrystalline failure of alloys under creep conditions. The effects of grain size on the creep properties of impure and high purity materials are discussed in the same light. The experimental procedures and technique have been presented elsewhere.' It is only necessary to state how the 2s and 3s aluminum specimens are prepared. Machined specimens were first annealed at 600°F for about 12 hr. In order to produce a large grain size the specimens were then stretched 3 to 8 pct. The specimens were marked with reference marks, electropolished, annealed at 900°F for 24 hr and at 1150°F for 12 hr, and repolished. The grain size of 2s aluminum produced by this treatment is comparable to that of high purity aluminum in the direction of its width of the specimen, i.e., there are 2 to 4 grains across the width of the specimen. However, the grains of 2s aluminum are 3 to 10 times longer in the direction of the specimen axis. On the other hand, the grain size of coarse grained 3s aluminum ranges from 10 to 20 grains across the width of the specimen due to the treatment just outlined and therefore is much smaller than that of both high purity and 2s aluminum. As in 2s aluminum, the grains are about 3 to 10 times longer in the direction of the specimen axis than in the direction of the width of the specimen. The arrangements of the grains in 2s and 3s aluminum were generally irregular; therefore it was difficult to follow the course of the grain boundaries. Results Method of Presentation: In order to show the arrangement of the grains, especially the direction and positions of the grain boundaries, traces of the grain boundaries on the four surfaces of the specimens were unfolded and mapped out after macroetching. Figs. 1 and 2 show the structural development drawings of specimens P-3 and P-8 respectively. The two flat surfaces (of which the front one faces the microscope) and the round-edged surfaces will be called the "front surface" and "back surface" and

Jan 1, 1954

By Robert F. Mehl

Jan 1, 1944

By Robert F. Mehl

Jan 1, 1944

Executive Committee. Louis D. HUNTOON, Chairman. ARTHUR S. DWIGHT, Vice- Chairman. E. MALTBY SHIPP, Treasurer. GEORGE F. KUNZ, HOMAS T. READ, Secretary. Woolworth Building, New York, N. Y. Meeting, May 2,1913. The Annual Meeting of the New York Section was held at the Engineering Societies Building, Friday evening. May 1913, at 8 p.m. Dr: Kunz presided. The Annual Report of the Secretary-Treasurer was read and accepted. Mr. Colvocoresses offered the following amendments to the By-Laws: ARTICLE II: First paragraph amended to read as follows: "The officers of this Section shall be. a Chairman, Vice-Chairman, Secretary, and Treasurer." In the second paragraph the word "four " to be changed to " five." ARTICLE V : The following paragraph to be inserted: ' The funds of this Section shall be received by the Treasurer, and shall be paid out only by check signed by the Treasurer, and in case of his absence or inability, the Chairman, Vice-Chairman, or the Secretary may act for the Treasurer." On motion duly seconded the amendments were adopted as read. The Nominating Committee, appointed by the Chairman, recommended the following men for officers : Chairman., Louis D. Huntoon ; Vice-Chair-man, Arthur S. Dwight; Secretary, Thomas T. Read, and Treasurer, E. Maltby Shipp. There being no other nominations, Mr. Rand moved that the Secretary be authorized to cast the vote for the members in favor of the men nominated. Motion carried. In reply to the circulars mailed regarding the summer outing the Secretary reported that 89 members approved and 9 did not approve of such an outing. The Chairman introduced Dr. M. Belowsky, of the University of Berlin, who addressed the meeting in German. Following Dr. Belowsky, the speaker of the evening, A. H. Fay; of the Bureau of Mines, discussed Metal Mine. Accidents.

Jan 6, 1913

By A. U. Seybolt, J. L. Walter

The effects of the addition of 0.5 pct ThO2 (by volume) on the grain structure and texture of heavily rolled tungsten sheet were studied. Powder metallurgy ingots were rolled to sheet, 0.001 in. thick, and samples were annealed at temperatures from 1200" to 2500°C. The heating rate to the anneal temperature was varied from 3°C per min to 6500°C per min. The orientations of the largest grains were determined by X-ray diffraction. The disposition and loss of the ThO2 particles were determined by electron transmission microscopy and the activation energy for remozlal of the thorium was measured by mass spec-troscopy. Heating rates below about 800 C per min produced large, highly elongated grains. Higher heating rates produced much smaller, less elongated grains. The grain structure and texture of the slowly heated samples were identical to the structures and textures of heavily rolled tungsten foil conventionally doped with aluminum, silicon, and potassium but the recrystallization temperature was about 200°C lower. There was stringer-like dispersion of larger ThO2, particles superimposed on a uniform dispersion of fine particles. The particles increased in size and decreased in number with time at temperature. The loss of particles was accompanied by formation of grain boundary voids and surface pits. The activation energy for removal of the ThO2 was about 40 kcal per mole. THE addition of small amounts of aluminum, silicon, and potassium to tungsten has a profound effect on the grain structure of heavily rolled sheet1 or drawn wire."4 Thus, "doped" tungsten sheet, rolled to 0.001 in. and recrystallized, develops a structure consisting of large, highly elongated grains of a specific preferred orientation.' It has been shown that the elongated grain structure was caused by a dispersion of particles, identified as mullite (Al6si2O13),1,4 in strings parallel to the rolling direction in sheet or to the wire axis. Identical results were obtained for iron which was doped with glass and rolled to 99 pct reduction of thickness and recrystallized.5 Again, the glass particles were disposed in strings parallel to the rolling direction. The strings retarded boundary migration in the lateral direction but grain growth was able to proceed relatively unhindered along the direction parallel to the strings.1,5 In both the doped tungsten and the glass-doped iron, the particles were highly plastic during the high-temperature deformation. Since mullite melts at about 1800°C and the glass employed melts at about 810ºC, the particles were probably molten during the recrystallization anneals (above 1800°C for the doped tungsten and 850°C for the glass-doped iron). There are indications in the literature that particles not plastic at hot-working temperatures (up to about 1550°C for tungsten) may also impart elongated grain structures by primary recrystallization of worked alloys. Examples are dispersions of tantalum carbide in chromium,6 and ThO2 in nickel where elongation ratios of recrystallization grains of up to 20:l were obtained.7 Strings of ThO2 particles in W-ThO2 wire have been seen by Rieck.8 In view of the available evidence, it was of interest to extend the previous studies of doped tungsten and glass-doped iron to include W-ThO2 sheet materials. Of specific interest was the grain structure, preferred orientation, recrystallization temperature, and disposition of the thoria particles. EXPERIMENTAL PROCEDURE A) Material Preparation. About 380 g of blue tungsten oxide (approximate composition WO3) was wet with a sufficient amount of aqueous solution of Th(N03)4 to provide 0.5 vol pct ThO2. The wet mixture was stirred to distribute the doping material uniformly throughout the powder. Stirring was continued while the mixture was heated until it was completely dry. The dried, doped mixture was then reduced to tungsten powder by heating at 850°C for 2 hr in a stream of dry hydrogen. The doped tungsten powder was hydropressed in a rubber sack at pressures of 50,000 psi to produce an ingot approximately 2 cm diam by about 5 cm long. Next, the pressed cylinder was heated in hydrogen for 2 hr at 1350°C to render it strong enough for machining. The cylinder was machined to a square cross section of 1.6 by 1.6 cm with rounded corners. Finally, the bar was heated for 2 hr at 2150°C in hydrogen to provide a sufficiently dense mate rial to withstand the hot-rolling operation. Prior to rolling, the ingot was reduced in thickness by about 20 pct by forging at 1550°C. This served to increase the density of the material and to widen it slightly for better rolling characteristics. The forged ingot was then rolled at 1550°C to a reduction of 45 pct of thickness, following which the rolling temperature was reduced to 1300°C and the slab rolled, with several reheats, to 0.050 in. Further reduction was accomplished at 800°C in tungsten sheet packs to a total reduction of about 99.85 pct. B) Annealing Treatment and Observation of Structure. Small samples of the rolled foil were annealed in one of two ways. Some of the samples were suspended in a covered tungsten can and annealed at temperatures from 1200" to 2200°C for various times in vacuum of l0-7 to 10-6 mm Hg. The can was heated by induction and temperatures were determined by optical pyrometry

Jan 1, 1970

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

By Malcolm C. Bridges, Ian A. Goddard

INTRODUCTION Mount Isa mine is a major producer of both copper and lead-zinc- silver ores. During the 1975/76 year, 4.3 million tonnes of copper ore were extracted at an average grade of 3.4%, and 2.4 million tonnes of lead-zinc-silver ore at average grades of 7.0%, 6.7% and 173 grams per tonnes respectively. Systematic lead-zinc mining has continued for just over 45 years and copper mining for just over 30 years. Virtually all mining is underground. The composite and somewhat schematic longitudinal section of Figure 1 shows the overall distribution of ore at the Mount Isa mine. The mine can be roughly divided into two parts about a central shaft complex: to the north there is predominantly lead-zinc ore and to the south there is copper ore. Underground operations are serviced by three shafts in the central shaft complex (P61, R62 andU62) and another to the south in the copper mining area (X41). Mining is spread over a total strike length of 2.9 km and extends to a depth of 960 m. Currently, lead-zinc ore is being extracted between 15 and 11 levels and is hauled to the central ore-hoisting shaft on 13 and 15 levels. Copper ore is being extracted between19 and 13 levels and is hauled to the central shafts on 19 level. The principal lead-zinc mining methods used now, as they have been over the last ten years, are sublevel open stoping and cut-and- fill stoping, with about equal tonnages of ore from each (Figure 2). Since about 1970, there have been several interesting developments in lead-zinc mining methods and procedures, principally: • the development of an effective method for the recovery of pillars between open stopes and • the evolution of safer and more productive cut-and- fill methods. During this period also, the focus of mining has moved 120 m deeper

Jan 1, 1977

By George A. Roberts, Arthur H. Grobe

Tensile, hardness and density properties are presented for a new 18-8 stainless steel powder for the —50, —100, and —140 mesh cuts and also for a prepared blend containing 62 pct —325 mesh powder. The data were obtained for sintering temperatures of 2100° to 2350°F and for compacting pressures of 30 to 50 tons per sq in. A NEED has existed for a stainless steel powder of uniform composition from particle to particle, which could be readily molded and sintered, and which would yield moderate to high strength and ductility when processed into parts by standard powder metallurgy techniques. The literature reveals that previously available powders have been lacking in one or several of these desirable characteristics. Originally attempts to produce stainless steel powder by blending and diffusing elemental metal powders were unsuccessfu1.l A truly alloyed stainless steel powder reported by Dale in 1947 yielded reasonable mechanical properties but required an exceptionally high sintering temperature of 2400°F in pure dry hydrogen.' A later development reported in 1950 by Stern provided a stainless type powder of excellent molding properties' but this powder likewise required sintering at temperatures over 2350 °F and did not yield properties as high as those previously reported. The powder was not truly alloyed prior to sintering. A prealloyed stainless steel powder has been developed that is readily moldable at 30 to 50 tons per sq in., can be sintered at low temperatures (2100" to 2300°F), and which yields compacts with both high strength and ductility. The powder is prepared by the liquid disintegration method," direct from molten metal. Early attempts to make 18 pct Cr, 8 pct Ni stainless steel powder by this method did not produce a usable powder for pressing and sintering because of a preponderance of spherical particles with relatively high, surface oxide content. It was learned that silicon additions to iron alloys, powdered by this process, gave bright powder of low-oxide content and such additions were made to 18-8 stainless with similar results. An attendant change in particle shape occurred reducing the number of spheroids materially. The optimum composition which has been studied and is reported here contains approximately 2.5 pct Si. Silicon additions to stainless steel of the 18-8 type improve the resistance to high-temperature oxidation and promote the formation of ferrite. Corrosion resistance is, however, controlled by chromium content and even though ferrite may exist the corrosion resistance is not generally impaired.4 Experimental Procedure A detailed study of the 18-8, 2.5 pct Si powder has been made in accordance with the following outline: 1. Four blends a. — 50 mesh b. —100 mesh

Jan 1, 1952

By W. F., Dietrich

THIS paper deals with the- methods of mining the high-grade clays of California. Although the majority of the clay pits in the state are operated on a scale that is small by comparison with most metal mines, this very fact results in a diversity of methods and gives rise to problems of selection of the method best suited to given conditions. Two or three operators in California produce approximately 500 tons per day of a single kind of clay from a single pit. About five varieties of clay are mined on a scale of 200 to 400 tons per day; not over fifteen varieties are mined on a? scale of 50 to 200 tons per day; and more than 50 varieties are mined at a rate of less than 50 tons per day. It is the aim of this paper to delimit, insofar as the data at hand permit, the conditions and scale of operations that favor the selection of each dominant method of mining that is actually being applied at California properties. Details of the occurrence and utilization of the clays of California have been given in a recent bulletin and are not considered here.

Sep 1, 1928

By Kenneth B. Ray, George R. Gardner

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By George R. Gardner, Kenneth B. Ray

The application of wet cleaning processes for the beneficiation of bituminous coal has created in some localities a problem in the recovery and disposal of fine solids in the washery water. The maximum allowable concentration of these solids in the washery circuit that is consistent with satisfactory operation of the cleaning units remains a controversial point. It has, however, been generally recognized for a number of years that some degree of control should be exerted over the concentration of such material. Early methods of control involved intermittent or continuous discharge of a portion of the plant slurry into near-by streams or settling ponds, and this persisted even after the adoption of settling tanks or cones. The practice is not always economical, for two reasons: first, because of the waste of coal, and, second, because it is sometimes difficult and expensive to obtain an adequate supply of water. The latter condition often is aggravated by chemical treatment of the make-up water that is necessary to prevent excessive corrosion of plant equipment. The modern approach to this problem has been the adoption of continuous thickening devices. However, because such equipment occupies considerable plant space and is somewhat expensive to construct, the practice of loading these thickeners beyond their rated capacity is widespread, therefore often the performance of such units is not altogether satisfactory. In recent years, European washeries have increased the rate of settling of the fine coal from the slurry by the addition of specially prepared starch solutions. These reagents cause flocculation of the solid particles and thereby increase the rate of sedimentation. The first important work on the flocculation and clarification of coal slurry was done by Henry, who developed the Henry process and used it successfully in Belgian preparation plants. Soon after the initiation in Belgium, the process was introduced into England, where subsequent investigation developed similar processes, which were successfully used in

Jan 1, 1940

By P. Shahinian, J. Weertman

Minimum creep rates of nickel samples were measured in the stress region of 2.5x107 to 2.8xl0 dyne per sq cm and the temperature region of 400° to 1100°C. The creep rate seems to be proportional to (stress) at stresses below 7x10H dyne per sq cm. The activation energy of creep is approximately 65,000 cal per mol. IN a recent theory' of steady-state creep which is based on Mott's dislocation climb mechanism, the following creep equation was derived for creep in polycrystalline metals (if where K is creep rate, Q the activation energy of self-diffusion, S the entropy of activation of self-diffusion, L' the grain size, L the subgrain size, b the length of the Burgers' vector of a dislocation, u the shear modulus, u the stress, a the critical shear stress, M the density of active Frank-Read sources, v the vibrational frequency of a vacancy, and kT has its usual meaning. This equation predicts a creep rate which depends on the stress through a power law at low stresses. At high stresses the creep rate increases much more rapidly with stress. The theory breaks down for stresses great enough that the inequality holds true. It was the purpose of the present in-

Jan 1, 1957

By Jack F. B. Silman

Proving up any large, open pit ore deposit by normal exploration drilling under the best of conditions is a noteworthy accomplishment. But, when adverse conditions preclude standard drilling methods, and the same end result is achieved by a relatively new and little known type of drilling, special comment is in order. Three major problems confronted exploration drilling at the Questa molybdenite mine of the Molybdenum Corporation of America-sampling, terrain and time. Surface and underground longhole drilling provided the needed solutions, thus making the greatest single contribution to an exploration and development program that was successful in proving a major, open pit molybdenum deposit.

Jan 5, 1965