Search Documents

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By J. J. Rutledge

On Sept. 4, 1914, Mine No. 1 of the Union Coal Co., Adamson, Oklahoma, suddenly caved, entombing thirteen miners whose bodies were never recovered. The seam of coal mined, the Lower Hartshorne, averaged 5 ft. in thickness and dipped at an angle varying from 22" to 30n. The strata overlying the coal seam were sandstones and shales. The mine was worked by the pillar-and-room method, the rooms being driven directly up the dip of the seam. All coal was blasted off the solid. Rooms were turned on short centers and room pillars were thin and irregular, as shown in Fig. 1. Fig. 2 is a cross-section of the form; showing the mine workings. Some cracks had been observed on the surface, it is said, at least a month before the squeeze occurred, but the collapse of the mine workings came very suddenly. As is usual when squeezes occur on such steep dips and the pillars fail, the crush progressed rapidly down the dip until it reached solid coal; there was a line of break, or draw, over in the solid coal. Several well-defined cracks appeared on the surface, after the mine had squeezed, but there was no appreciable subsidence of the surface, the weight seemed to be thrown entirely to the dip. About one year after the squeeze, and after the workings of the adjoining mine, NO. 4, had been retimbered and made safe, the writer inspected the tenth north (right) entry, or lift, off of No. 4 slope, which was below and fairly near the lowest caved portion of mine No. 1. The roof shale was composed of thin layers, which had been bent in somewhat the same manner as the leaves of a book having flexible covers are bent when the book is folded or rolled up in the hands. Though the mine workings are immediately beneath the streets and buildings of the mining town of Adamson, business was not disturbed by the squeeze, so far as any subsidence of the surface was concerned. No surface monuments were available and no elevations were taken, but the mine workings had been accurately surveyed and traversed, and the streets of the town overlying the mine workings had been carefully platted on the mine map, so that it was possible to locate accurately the cracks on the surface.

Jan 1, 1923

By W. E. Remmers

The defect in wire known as "cuppiness" has appeared and disappeared from time to time but the exact cause of its appearance or disappearance has not heretofore been known definitely. This defect is not limited to one particular metal or alloy but seems to be found at various times in all of the materials that are drawn into wire. Fig. 1 represents cuppy wire made from an aluminum alloy and Fig. 2 illustrates copper wire that became cuppy in drawing without intermediate annealing. Differences of opinion are current among the manufacturers of wire and in the literature (see bibliography at end of paper), some believing that the source of the trouble lies in segregation in the wire rod, oxides, sulfides, slag, etc.; others that the trouble is created by an unevenness of stress distribution across the section of the wire, usually thought of as being a function of die shape. All of the published work is of a qualitative rather than a quantitative nature. With this in mind, it was deemed advisable to make a study of the shape of the wire-drawing dies, as well as the oxygen content of the copper to be drawn. Experimental After several methods were tried, it was found that by studying the contour of the butt-end of the rod after drawing a measure of the "working" across the section of the wire could be made. The butt-end of the annealed rod was not sheared but was sawed off. The end was then smoothed with a fine file so that the plane of filing was perpendicular to the drawing axis. It is to be noted that this method is not an absolute measure of the distribution of cold working but is a very good indicative means of studying comparative values. The method of examining a tension break in wire was found to be the most sensitive in detecting cuppiness. Other methods, such as microscopic examination of longitudinal sections, X-ray radiographic studies, etching away of outer layers with nitric acid, and fracture by bending, can all be used to identify cuppy wire but the tension break will give the fracture characteristic of cuppiness before any of the other methods can

Jan 1, 1930

By H. I. Aaronson, S. Toney

When the component grains of .ferritic hicrystals of an Fe-1.55 pct Si alloy are disoriented through an angle "6 " about a conzmon [ll0] axis, the tendency for preferential growth of austenite crystals along the grain boundary during transformation at elevated temperatures is small when 11 deg, but increases rapidly at larger angles. This type of orientation-dependence indicates that grain boundary diffdsion promotes preferential growth along large-angle boundaries. Morphological differences between austenite crystals formed at small-angle [1101 and [loo] boundaries suggest that precipitate morphology can be dependent on the dislocation structure of the boundary. ThE morphology of precipitate crystals nucleated at a grain boundary can be significantly affected by the structure of the boundary.' The limited amount of experimental evidence available in the literature indicates that the morphological effects of boundaries made up of arrays of dislocations, such as subbound-aries and small-angle grain boundaries, are different from those of boundaries having essentially disordered structures, i.e., large-angle grain boundaries. On the basis of indirect evidence, it has been concluded that large-angle grain boundaries give rise to the formation of grain boundary allotriomorphs (crystals which nucleate at grain boundaries, and grow preferentially and more or less smoothly along them)2 in the proeutectoid ferrite and the proeutec-toid cementite reactions in plain-carbon steels, and apparently also in many non-ferrous alloys.' At small-angle grain boundaries in a plain carbon steel, on the other hand, ferrite crystals were found to take the form of primary side plates. Similarly, Guinie, loys. Primary sideplates formed at a subboundary with a constant orientation tend to be parallel to only one, or occasionally two matrix habit planes, and a marked change in the orientation of the boundary is accompanied by a change in the habit plane. Previous studies on the morphological effects of grain boundary structure were performed on poly-crystalline aggregates. Information on the disorien-tation of the pairs of grains forming the boundaries at which the various morphologies appeared in these specimens was largely either qualitative or semi-quantitative. Precipitate morphologies accordingly could not be accurately and systematically correlated with grain boundary structure, and thus theories which have been proposed for the various morphological effects could not be satisfactorily tested. This investigation was undertaken in an attempt to remedy these deficiencies by studying the morphological effects of grain boundary structure with a method in which the boundaries are formed by matrix grains whose disorientations are known and controlled with reasonable accuracy. EXPERIMENTAL PROCEDURE The crystallographic requirements of this study were fulfilled by means of oriented bicrystals of silicon-iron. Disorientation of the component ferrite crystals was carried out about common, major crystallographic axes through angles ranging from 1/2 to 44 deg. The silicon content was low enough SO that the bicrystals could be partially transformed to austenite by heating to elevated temperatures. The silicon-iron used had the following initial composition: 1.55 pct Si, 0.04 pct C, 0.0031 pct N, 0.17 pct Mn, 0.020 pct S, and 0.002 pct P. The alloy was obtained in the form of 0.036-in. sheet. The procedures employed to prepare seed crystals in strips of this sheet, to reorient the seeds, and to grow them into bicrystals are essentially those described by Dunn and Nonken and aynes." The characteristics of the bicrystals are given in Table I. The "bicrystal type" indicates the crystallographic plane parallel to the broad faces of the strip in both grains and the crystallographic direction which was parallel to the long edges of the strip in both grains prior to disorientation. The angular disorientation of the grains, 8, which was performed about the direction normal to the plane of the broad faces of the strip, was measured between the [ 00l] directions. Orientation of the grain boundary, , was taken as the angle between the plane of the grain boundary and a plane containing the axis of disorienta-

Jan 1, 1962

By John Lohrenz

Consider an investor who, knowing future costs and revenues, can choose how rapidly to produce from a given mineral source. If the investor elects to make that choice to maximize present value of future profits, how do policies affect the choice? Various alternative policies are examined. Some, such as higher royalty rates, lead to slower production rates than would otherwise obtain. Clearly, the chosen rates of production are policy-dependent. One is wisely counseled to consider how mineral policies affect the rate of production from given sources when analyzing current and alternative policies.

Jan 1, 1982

By B. D. Cullity, S. S. Hsu

The stress distribution at the surface of a twisted cylinder is analyzed along the boundary of a slip plane of arbitrary orientation and this analysis is applied to the torsion of cylindrical crystals of magnesium. A criterion for slip is developed and the critical resolved shear stress of magnesium in torsion is found to be 0.038 kg per sq mm. The mechanism of torsional deformation in magnesium and aluminum is described, as well as the relaxation of a twisted crystal at elevated temperatures. THERE has been considerable fundamental study A of the mechanism of slip occurring during deformation in tension and compression but comparatively little attention has been paid to the mechanism of torsional deformation. This paper is concerned with the way in which a single crystal deforms in static torsion and with the phenomenon of untwisting which a twisted crystal undergoes during annealing. Particular attention is paid to the application of the critical resolved shear stress law to torsional deformation. Probably the most likely mode of torsional deformation that can be imagined consists of rotation of one part of the crystal relative to another on the active slip plane. Here the most interesting feature is the slip direction. If a cylindrical single crystal is twisted about its axis and if, to consider the simplest case, the active slip plane is normal to the specimen axis, then the direction of gross slip at any point must always be at right angles to the radius drawn to that point. It follows that the crystallographic direction of slip must be continually changing, in sharp contrast to slip in tension which occurs in a crystallographically constant direction. Extensive investigations of slip in torsion have been made by Gough and his associates.' They made torsional fatigue tests on metal single crystals belonging to a number of different crystal systems and observed, with a microscope, the appearance of slip lines on the surface and of strain markings on the transverse cross section of cylindrical specimens. They concluded that the critical resolved shear stress law was just as valid in torsion as in tension, in the sense that slip occurred on that plane and in that direction in which the resolved shear stress was a maximum. They also established that the operative slip planes and directions were the same as in tension. They did not, however, measure the critical resolved shear stress in torsion nor, in fact, did they establish that a critical value of the resolved shear stress was necessary for the initiation of slip. Their investigations were, moreover, restricted to torsional fatigue tests which necessarily involve small strain amplitudes. Wilman,' studying crystal growth and the abraded surfaces of crystals, observed crystal fragments

Jan 1, 1955

TITANIUM is one of the most abundant elements in the minerals that make up the earth's crust but its use in industry is only a generation old; yet probably no other important commercial mineral raw material (except possibly magnesium) has undergone more changes and developments in sources of supply, in processing techniques, in uses and applications, in the past 10 years, or stands on' such a threshold of still more advances. Its outstanding use today is as the oxide, and because of its extreme whiteness, high refractive index, chemical stability, and relative cheapness, it has become the white pigment used in the largest volume. New developments in the uses of titanium metal, potential and actual, may surpass the pigment use of the oxide before many years. TITANIUM-BEARING MINERALS Although a number of minerals contain titanium as the principal metal, only a few are of commercial importance. These are arizonite, ilmenite, and rutile. The other oxides, brookite, pseudobrookite, and anatase, occur in a few deposits, one at least of minor importance. The silicate titanite, and the double oxide of calcium and titanium, perovskite, occur in a few deposits in quantities sufficient to be considered as potential ores were not richer deposits of the oxides available elsewhere. Arizonite is a name given by Palmer46a to a mineral found some years ago in minute quantities in Arizona, which has the formula Fe203.3Ti02. Unexpectedly, it was found that the black titaniferous iron oxide found in large quantities on the beaches of many continental land masses corresponds in chemical composition to this formula (although ferrous oxide is always present). No one has yet been able to prove that the commercial mineral on the beaches is truly arizonite, or an allotropic modification of it, since X-ray investigations by Howard Carl and A. F. Gabriel, of the U. S. Bureau of Mines, and by the X-ray laboratory of the Chemical Department at the Experimental Station of the du Pont company, have shown only that the sand mineral gives just a jumble of lines, rather than an identifiable pattern. Lack of a better name,

Jan 1, 1949

By Herbert R. Hanley

THE One Hundred and Twenty-sixth meeting-of the Institute, held in San Francisco, Sept. 25 to 29, 1922, was a success in every way. Character-istically, San Francisco presented climate suited, to the occasion, while the Committees on Arrangements left nothing undone that would contribute to the interest and entertainment of the members and their wives. There was a registration of over 230, and all sections, save three, were represented. In the technical meetings, under the leadership of Albert Burch in the mining session and C. W. Merrill in the milling session, the greatest interest was manifested in ore-hunting geology and modern ore-dressing methods. The general geologic phase developed numerous discussions and had for its aim the study and correlation of known data and the application-of these to the finding of commercial orebodies. The geologic features of the Comstock and their significance to the development of the present orebodies were discussed. This brought out matters of much technical interest as well as those of romantic nature in the history of the early life of that camp. The profitable application of modern milling methods to ores, non-commercial a short time ago, was discussed with much interest. The recent work on the Comstock ores occupied a conspicuous part in these discussions. Basic principles delineated by mathematical study of mechanical devices for the milling of ore came in for a prominent part in the program as well as the physical-chemical side of the processes devised for the winning of precious metals as a profit.

Jan 11, 1922

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By W. T. Turrall, D. Porter

The paper describes a machine developed for the purpose of concentrating clear optical grade fluorspar crystal from a feed material containing less than 1 pct impurities. The principle of concentration is based on the fact that in a liquid having an index of refraction equal to that of fluorite (n — 1.434) clear crystals are invisible, whereas crystals containing occluded impurities absorb a part of the light. As the crystals pass through a light beam, undesired crystals give themselves away by creating a shadow on a photoelectric receiver. .The shadow is converted by the photoelectric cell into an electric pulse. An electronic circuit amplifies this pulse and commands the operation of a mechanical concentrator. Hp HE crystal laboratory, Dept. of Physics, Massa--*- chusetts lnstitute of Technology, was confronted with the problem of obtaining a supply of optical grade calcium fluoride (CaF,) for use in growing synthetic CaF, crystals. A search of the known fluorspar deposits did not indicate that any quantity of optical spar could be obtained. Even the best material had to be sorted by hand to remove impurities. The process for growing CaF, crystals developed by Professor D. C. Stockbarger of the Dept. of Physics, M.I.T., necessitates very pure feed materials. Exclusion of impurities is required, even in amounts detectable only spectrographically. The impurities occurred as minute inclusions of SiO,, BaSO,, CaCO,, FeS2, water or air. Crystals up to 4 in. in diam and weighing several pounds are made by the Harshaw Chemical Co. in Cleveland. Since the time required to grow a 4-in. crystal is about one week, and since the cost of manufacture is high, removal of impurities by any concentration method appeared practical. The mineral engineering section of the Dept. of Metallurgy undertook to investigate the possibility of concentrating clear optical fluorspar, —4 mesh + 10 mesh, from a feed containing over 99 pct CaF,. Various innovations of the known methods of concentration were considered, but in each case the minute amount of impurities associated with the crystal produced such extremely small differences

Jan 1, 1953

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of in- creasing importance to the economic life of the northern field operations. Successful approaches have Been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas; the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 1, 1950

By Wayne C. Hazen, James K. Kindig

As the complexity of hydrometallurgical systems increases, it offers new opportunity for applications of solvent extraction. However, the high capital cost of mixer-settlers for large flow rates is a drawback to wide application in base metal recovery. This paper presents information on the use of cyclone separators in place of settlers with attendant significant reduction in capital cost. Various flowsheet possibilities for this development are discussed.

Jan 1, 1972

By W. E. Forsythe

WHEN measuring ordinary temperatures, the instrument is generally placed in very close contact with the body the temperature of which is desired. However, if the temperature of the source is continually raised, a point is soon reached where no known substance will, in general, remain constant in any of its temperature-measuring properties if placed in direct contact with the source. Also, it is occasionally necessary to measure the temperature of a source that 'is so small or so situated that it would be very hard to bring the measuring instrument into direct contact with the source. When these conditions exist, advantage is taken of the well-known fact that all bodies, when at sufficiently high temperatures, send out radiation in amounts readily measurable. This radiation has been found to be related to the temperature. The temperatures of very hot bodies have probably always been judged by the color, or the brightness, of the light given off. With practice, one can estimate probably within 50° to 100° C. of the correct value. However, if judgment is left to the eye alone, very much larger errors are sometimes made, due to

Jan 9, 1919

By Victor Formanek, Paul Chataignon, Maurice Rey

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By Maurice Rey, Victor Formanek, Paul Chataignon

IT is found when floating oxidized lead ores by sulphidization, that the presence of calcium salts in the water, is usually detrimental and lowers the recovery. This effect is particularly marked in dry countries such as North Africa, where the waters often carry large amounts of calcium sulphate and where the ore may even contain gypsum. The effect of calcium salts is readily visible. Whereas in their absence cerussite is quickly stained brown and then black by sodium sulphide, in their presence the mineral remains very light in color. A similar effect is produced when barium sulphide is used as a sulphidizing agent instead of sodium sulphide. Magnesium salts have little or no effect and even tend to reduce the detrimental effect of calcium salts. A study of this phenomenon indicates that it is due to the precipitation of calcium or barium carbonate in contact with the mineral simultaneously with the formation of lead sulphide. The chemical reactions can be interpreted as: PbCO3 + Na2S = PbS + Na2CO3 CaSO4 + Na2CO3 = CaCO3 + Na2 SO4 They might also be written: PbCO3 + S = + Ca++ = PbS + CaCO3 The precipitation of calcium carbonate can be followed by the lowering of the pH with which it is accompanied. Magnesium carbonate is more soluble than calcium carbonate and usually does not precipitate under the conditions prevailing. It is interesting to note that calcium salts have no effect on anglesite (lead sulphate) because calcium sulphate is soluble, but barium salts hinder the sulphidization of anglesite because of the precipitation of barium sulphate. Remedies When calcium sulphate is present in large amounts, the softening of the water with soda ash is usually too expensive to be considered, but the precipitation of the objectionable calcium carbonate can be prevented in two different ways. One is the use of sodium hydrosulphide instead of sodium sulphide. This salt gives a lower pH than sodium sulphide and does not bring about the immediate precipitation of the calcium which remains in solution as calcium bicarbonate. The other procedure is to add ammonium salts such as the sulphate or chloride which have the property of increasing markedly the solubility of calcium carbonate. Ammonium salts have other effects such as cutting down conditioning time and accelerating flotation. They should be added to the flotation cells rather than to the ball mills. Table I. Effect of Sodium Hydrosulphide and/or Ammonium Sulphate on the Flotation of Two Oxidized Lead Ores Mibladen Ore4 La Plagne Ored Con- Tall- Con- Tail-centrate ing centrate ing Reagents Pb, Pct Pb, Pct Pb, Pct Pb, Pot Without addition of CaSO, NaS 56.0 0.68 43.4 0.65 NaSH 56.2 0.60 40.4 0.50 Na2S + (NH4)2SO4d 54.6 0.56 NaSH + (NH4)2SO4d 43.0 0.66 With addition of 40 lb/ton CaSO4 Na2S 39.4 3.85 34.0 3.21 NaSH 49.1 0.70 49.6 0.88 Na2S + (NH4)2SO4d 53.9 0.85 NaSH + (NH4)2SO4d 51.0 0.45 41.1 0.78 In table I are given the results of representative tests on two different oxidized ores. They show that the strongly detrimental effects of calcium sulphate can be offset by the two procedures outlined above. Sodium hydrosulphide is now used regularly on a mill scale on certain ores. Tests are being carried out with ammonium salts. It should be noted that malachite is subject to influences similar to cerussite. One final word of caution—when the ore is rich in primary slime, which is flocculated by the calcium salts, it may be indispensable to remove these by washing or precipitation with sodium carbonate instead of keeping them in solution by the above methods. Acknowledgment We wish to thank Socibtk Miniere & Metallurgique de Penarroya and Minerais et Metaux, for permission to publish these results.

Jan 1, 1951

By Grover R. Castle

INTRODUCTION "Project Financing" or "Project Loans" have become increasingly popular in recent years, and commercial banks are being asked to consider more and more of such financing. However, the analysis of this type of loan is quite different from the analysis of a loan to a financially sound corporation based on the company's balance sheet. For this reason Chemical Bank did a study of project loans in an attempt to be more sophisticated in our approach to them. As part of this study, we examined 29 project financings for which information was available. In this article I shall describe project loans and set forth the guidelines we developed, as an aid to credit officers who might have occasion to analyse this type of financing. DEFINITION OF "PROJECT FINANCING" OR "PROJECT LOAN" The terms "project financing" and "project loan" commonly describe the various methods that banks and institutional lenders use to finance the construction of new projects on a basis whereby payout is anticipated from the revenue stream generated by the project. A project financing often involves a loan to a new entity formed specifically to own the project. The analysis of a project loan proposal is quite different from the analysis of other term-loan proposals since it involves a credit decision based on the review of a projection or forecast rather than of historical earnings and/or it involves the reliance on contractual obligations of third parties. Lenders are asked to assume the added risks associated with project loans because: 1. Project financing may permit a company to obtain additional leverage. It is possible for companies to arrange financing on a project basis that could not be arranged as a direct borrowing. For example, a company may not be permitted to borrow more money directly, due to a limitation in a bond indenture. However, a project financing can sometimes be negotiated on a basis not prohibited by the indenture. 2. Often the sponsors of, or the stockholders in, the project are seeking an off-balance-sheet financing. For example, 11 of the 29 projects in our study were arranged on an off-balance-sheet basis and one showed on the balance sheet as a deferred income item. An off-balance-sheet financing, for the purpose of this article, is a financing which does not show as a direct liability on the balance sheet of the sponsors of or stockholders in a project. 3. Projects are often located in a foreign country. The financing is arranged so that the lenders assume the political risk on the loan because many companies rightly believe that this arrangement affords a degree of insulation from political risk not otherwise obtainable. 4. Many projects are jointly owned by several sponsors. This form of financing lends itself well to a situation where a new entity is formed to own a project and do the borrowing. Project loans can be used to finance a variety of activities including development of iron-ore deposits and associated pelletizing plants; development of coal reserves; construction of pipelines, alumina plants, fertilizer plants and refineries; etc. The specific areas of analysis can be quite different, depending upon the type of project being financed. It is important, therefore, to classify the proposal according to the type of project, and also by the nature of the financing - nonrecourse financing, financing covered by a guarantee of completion and financing supported by an undertaking lasting for the life of the financing. I will discuss each of these types in more detail later, but first, I should like to make some

Jan 1, 1985

By Norman Carmichael, John Kiddie

The problem of transportation in the Clifton-Morenci district of Arizona has been one of peculiar difficulty and consequently has been an important factor in the cost of mining and treating the ores produced. From the crude beginning made over 50 years ago, many changes have been necessary to keep pace with the increased output of copper. A heavy-duty haulage system has developed on the original 20-in. track gage to meet the existent metal-mine conditions. Topography The transportation difficulties of this district may be readily appreciated from the relief map shown in Fig. 1. The northern half of the district is high mountainous country and there is a general but irregular drop toward the southern part, where the country, although still rugged, is in reality a great sloping plain. This is cut by numerous ravines from which the waters, in the rainy season, discharge into the channel of the San Francisco River. A chasm, 1000 ft. deep, has been eroded through the center of the district by Chase Creek, which is flanked by high irregular mountain masses, notably Copper Mountain, American Mountain, Coronado Mountain, and Markeen Mountain. The latter rises 2300 ft. above the bed of the creek, The San Francisco River has also cut a deep channel, though it is somewhat broader than Chase Creek. Eagle Creek traverses the extreme southwest portion of the area, where it has carved picturesquely through vast volcanic flows. Faulting has left its mark upon the topography of the district by adding to the irregularities caused by erosion. Strong faults occur at the Coro-

Jan 1, 1924

By G. O. Hiers

THE object of the experiments reported in this paper is to determine the eutectic composition of copper and tin and to determine the location of the part of the liquidus line immediately above the eutectic composition in copper. Three methods were used in the investigation: (1) the method of dissolving copper in a bath of molten tin at constant temperature, with the idea that when the bath was saturated with copper its copper content, by analysis, together with the temperature at which the saturation took place would locate a point on the liquidus line (2) the method of the differential cooling curves, and (3) the method of microscopic examination. This paper is principally concerned with the results of the last two methods mentioned. The results of the first method, that of dissolving copper in molten tin, did not agree with the .results of Miller,1 by the same method, nor with the results of other investigators by other methods, nor yet with the results of the cooling-¬curve experiments and microscopic examination reported here.

Jan 1, 1929

By R. C. Schmidt, B. E. Kennedy

The Mont Klahoyo magnetite deposit is located about 600 km (373 miles) northwest of Abidjan, Ivory Coast. During an exploration period ending in 1977 an international joint venture group investigated the deposit and proved reserves of 670 Mt (739 million short tons) grading 36% iron. The deposit occurs at the northeast end of the Baoubly-Kiriao chain of Precambrian iron formations with associated amphibolites, pyroxenites, and gneisses of the Liberian Shield. The ore body is represented by a highly metamorphosed banded quartz-magnetite iron formation with alternating beds of iron silicates and quartz-magnetite. Amphibolite-pyroxenites and sillimanite-cordierite-garnet gneisses form hanging and footwall rocks. The iron formation has been folded into an elongated, overturned 2-shaped major drag fold with axes trending and plunging approximately northeast. Beds are vertical or dip steeply to the southeast. The ore zone has an average thickness of 130 m (427 ft) and outcrops intermittently over a distance of approximately 5.5 km (3.4 miles). Based upon detailed studies of drill cores and the results of ore dressing test work, eight stratigraphic units, identified as K- 1 to K-8, are recognizable in the iron formation. Four interbedded units are low grade silicate zones (silicate facies) while the remaining quartz-magnetite units are oxide facies, representing the important Mont Klahoyo deposit ores. Ore-bearing "K" units are subdivided further into 11 ore types, based upon their specific lithologies, iron content, and concentration characteristics. Identification of these ore types proved particularly useful to mine planning and flowsheet design. A cap of oxidized material overlies the primary quartz- magnetite iron formation, but no enrichment has occurred. It is thought that the Mont Klahoyo iron formations were deposited chemically in a volcanic environment as a siliceous iron formation with volcanism the primary source of iron and silica. Metamorphism converted the siliceous iron formation to a coarse-grained, quartz-magnetite-silicate iron formation.

Jan 1, 1983

By Roy E. Dickerson

CUBA differs considerably from the other Greater Antilles in many geologic fundamentals. Cuba is geosynclinals; whereas Jamaica, Hispaniola. (Haiti), and Puerto Rico are geoanticlinal. (Scliuchert, Chas., Historical Geology of the Antillian. Caribbean Region, p. 13, 1935.) Rocks of lowermost Cretaceous age exist in large volume in Cuba, where- as they are generally absent in the other islands. Since many of the surface indications of petroleum are intimately associated with lowermost Cretaceous rocks, the Vinales limestone,, this difference is most important. The Vinales limestone in many places in Pillar del Rio and Santa Clara provinces reeks with light tars when broken with a hammer. The late David White and his associates on the U. S: Geological Survey studied

Jan 1, 1937