Search Documents

Jan 1, 1892

By Richard Borg

The partial molal free energy of Cd in each of the four intermediate phases, Cd3 Cu, Cd8 Cu5, Cd3Cu4, and CdCu2 is determined using the Knudsen vapor pressure technique. Measurements are made also within the two-phase regions, and thus the variation in FCd is now known across the entire phase diagram. The absolute values are all less the 2.0 kcal and increase regularly with increasing Cd concentration. The small absolute value of the free energy precludes the possibility of obtaining highly accurate values; nevertheless, the results are compatible with those previously reported for the liquid phase. Additional results are reported concerning the lattice parameters of the 6, E, and b phases. THE elements Cu and Cd combine to form four intermediate phases which are designated* and E and which include respectively the following inter metallic compounds: CdCu2, Cd3Cu4, Cd3 Cu5, and Cd3 Cu. The extent of each phase with respect to temperature and composition is shown in Fig. 1 which is the equilibrium diagram drawn according to Hansen.1 All four phases are brittle, and most probably are true intermetallic compounds. Only the crystal structure of the 6 phase has been thoroughly investigated.2,3 The structure is cubic and isotypic with y brass. The structure of Cd3 Cu has not been previously reported, It is hexagonal with a = 8.11 and c = 8.76 0.02Å and the structure is presently being determined.* The compounds Cd3 Cu4 and CdCu, have been each previously the subject of a single investigation. Cd3Cu, is presumed to be cubic4 with the space group Fd3m, whereas CdCu2 is hexagonal2 with the C14-type structure. Cu2 Cd is found by X-ray analysis to be hexagonat with lattice parameters a = 5.00A and c = 16.17Å. The material appears to be pure Cu2Cd as all reflections could be indexed on the basis of the single hexagonal structure. These values disagree with those of Kripyakevich and coworkers5 who report a = 4.96Å and c = 7.98Å. Their investi-

Jan 1, 1962

NEW MEMBERS The following list comprises the names of those persons who became members during the period Feb. 10, 1919, to Mar. 10, 1919. ALLEN, ROLLAND CRATEN State Geol., Appraiser of Mines, Lansing, Mich. ALTMAYER, MAURICE ERNEST, Ingenieur des Arts et Manufactures, 145 Rue de la Pompe, Paris, France. AUSTIN, CHARLES L., Assayer, Highland Boy Mine, Utah Cons. Min. Co., Bingham Canyon, Utah. BARTLETT, ARTHUR J., Chief Engr., Louisville Coal & Coke Co. Goodwill, W. Va. BOIES, ORLOW W., Research Chem., Roessler & Hasslacher Chemical Co., 1632 Tenth St., Niagara Falls, N. Y. BRAGG, G. A., Mgr., Experimental Copper Leaching Plant, Mellon Inst. of Industrial Research, Thompson, Nev. BRUSCANTINI, GIOVANNI, Min. Engr., Gen'l Mgr., Sindicato Minero de Cuba, Box 370, Santiago, Cuba. COLONY, R. J Instructor in Geol., Columbia University, New York, N. Y. DAVENPORT, FRANK B., Cons. Engr., 806 Coal Exchange Bldg., WiIkes-Barre, Pa. EATON, S. FORD 120 E. 85th St., New York, N. Y. EBY, J. H., Min. Engr Box 433, Spokane, Wash. ENGELHARDT, EDWARD A., Mgr., Surinaamsche Bauxite Mij, Paramaribo, Dutch Guiana, S. A.

Jan 4, 1919

Jan 1, 1881

By R. Lee-Aston

HALLOWAY mine of Tennessee Copper Co. at Copperhill, Tenn., has been under development for several years. It has two shafts, the A shaft, 1336 ft deep from the surface to the 16 level, and the B shaft, lying 500 ft to the southeast and extending 1385 ft deep from the 10 level down to the 24 level. A section through the two shafts, Fig. 1, shows the development work entailed by the proposal and the area involved. The Problem: For operational reasons it was necessary to extend the B shaft from the 10 level to surface, and the pilot hole and raising method was chosen. This method had been used to extend the Company's Boyd manshaft from the 10 to the 14 level in 1954, but no satisfactory hole surveying method had been employed. In that instance, when the hole was located it was found to be about 8 ft from its calculated position. The success of this shaft extension method lies in the ability to keep the pilot hole within the proposed shaft diameter for nearly the entire length. The approximate 670 ft of extension distance in one hole was thought to be excessive because of deflection encountered locally in other core drilling. Since a connection between the two shafts, intermediate between the surface and the 10 level, would be required at some future date, the pilot hole drilling was done in two sections. This intermediate level was fixed at the 6 level and distances became 470 ft from surface to the 6 level and 230 ft from the 6 to the 10 level. A rock pentice of 25 ft was left temporarily in place just above the 10 level.

Jan 3, 1958

By C. W. Pritchett

Several years ago, during a trip from Jojutla to Huauatla, in the abate of Morelos, Mexico, I was told by my guide of the ruins of an old smelter near by, and my curiosity was excited to such an extent that I went out of my way several miles to see them. I found them very interesting; and, as I fortunately

Jan 1, 1902

By James Douglas

The Copper Queen mine was opened in 1880 by Messrs. Martin, Ballard & Reilly, and the first copper-furnace was blown-in on August 20th of that year. Prior to that summer nothing but prospect-work had been done on the copper Queen and on a number of adjacent claims. In fact, it was a small deposit, not of copper-ore, but of cerussite, which still remains undeveloped, on the western slope of the Queen hill, which

Jan 1, 1900

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of September, 1913: Members. ANDERSON, ANDREW P., Min. Engr 908 Story Bldg., Los Angeles, Cal. ANDROS, STEPHEN 0., Min. Engr University of Illinois, Urbana, Ill. BECKETT, PERCY G., Min. Engr Globe, Ariz. BLAIR, THOMAS S., JR., Prest. Blair Engrg. Co 343 S. Dearborn St., Chicago, Ill. BOYLE, HARRY, Min. Engr S07 Lowman Bldg., Seattle, Wash. BRADEN, EUGENE B., Vice-Prest., Selby Smelting & Lead Co., Merchants Exchange Bldg., San Francisco, Cal. CHALMERS, JOHN W., Min. and Elec. Engr., Morro Velho, Villa Nova de Lima, Honorio Becalho Minas Geraes, Brazil, So. America.

Jan 10, 1913

By Fritz F. Prugger, Peter R. Jones

This paper considers some of the main aspects of underground mining in the flat, rich, but deep lying deposits of Saskatchewan. It briefly describes the pertinent geological features as they relate to mining and the practical de-stressing techniques used to allow productive extraction in the high stress environment present in many of the province’s mines. Mining layouts, materials handling, and the evolution of some of the world's largest mining equipment are examined.

Jan 1, 1983

By Samuel B. Christy

Jan 1, 1889

By E. A. Gulbransen, J. W. Hickman

INTRODUCTION DURING the past two decades considerable progress has been made in the art of manufacturing heater alloys. The conventional iron-chromium-nickel alloys have been improved by the addition of small quantities of other elements. Up to the present time, to our knowledge, there has not appeared a systematic study of these alloys where the newer tools of investigation have been brought to bear on the problem. It is not yet clear what roles the additional elements play in increasing life time in usage. As a first approximation one might guess that elements such as manganese, silicon, zirconium, calcium and aluminum would aid in the formation of a protective film on the alloy surface, thus retarding the oxidation rate and increasing lifetime. If these additional elements do form protective oxides in the outer surface of the oxide film, it may be possible to identify them by means of reflection electron diffraction. It is also possible that the additional elements may not diffuse to the surface but may remain at the interface between the oxide and the metal. Then, too, the major elements in the alloys undoubtedly form oxides which are stratified on the surface. If the minor elements concentrate in a layer in contact with the substrate where they undergo oxidation and if this oxide film offers resistance to the diffusion of iron, chromium and nickel ions, then the lifetime of the heater element might be expected to increase. It is also possible that preferential reduction in the diffusion rates of the several ions may occur to such a degree that oxides may form in the body of the film and on the outer surface which are different from those that would normally form if the additional elements were not present. The use of transmisson electron diffraction may aid us in interpreting these phenomena. Up to the present time all of the factors which influence the lifetime of a given heater element are not definitely known. Among these are: (I) The rate of oxidation of the alloy. This may be dependent upon the composition and the physical state of the alloy. (2) The stability of the structure of the coating which forms. Transitions from one structure to another or solid phase reactions resulting in a change of composition may occur. The tendency of the film to adhere to the substrate when heated and cooled successively will be important. (3) The evaporation of various constituents from the alloy such as the removal of carbon by oxygen in a decarburization reaction. With these possibilities in view, an electron diffraction study of the oxides occurring on six different nickel-chromium alloys was undertaken with the hope that the results of this study could be correlated with oxidation rate studies as determined by means of the vacuum microbalance method1 and with

Jan 1, 1948

AT THE beginning of December, the Lausanne Con-ference was in session. The representatives of the United States declared the American position. The representatives of Russia were received and were heard. The Turks appeared at this conference in the attitude of victors, dictating terms. The British refused to surrender Mosul, and December thus ended with this question unsettled. Early in the month the premiers of the principal powers met in London for the discussion of the German reparations question, the temporary agreement expiring on. Jan. 15, 1923. On Dec. 11 the Conference adjourned without getting anywhere, and at the end of December prospects looked more hopeless than ever. The premiers are to meet again on Jan. 2, 1923. The interruption of the London conference was followed by the intimation of early participation of the United States in European affairs in the practical way of a large loan to Germany. These intimations, ema-nating from Washington, appear to have been in the nature of trial balloons. They showed that the wind was unfavorable, the bankers not considering conditions suitable for the flotation of such a loan. British statisticians are puzzled by the fact that the trade returns of Great Britain show a greater turnover in the volume of goods during the first 11 months of 1922 than in 1920, although the rate of labor employ-ment in 1920 was nearly 100 per cent. and in 1922 only about 86 per cent., with an economic situation admit-tedly so bad as to be alarming. The British Parliament was convened under the premiership of Bonar Law. One of its first acts was confirmation of the constitution of the Irish Free State. Civil war in Ireland continued. Poland, like most of the other countries of Europe, is torn between socialism and conservatism, with the former party at present predominant. Early in December, Gabriel Narutowicz, an engineer but a radical, was elected president. On Dec: 14 he entered office and-on Dec. 16 he was assassinated.

Jan 1, 1923

By L. E. Porter

El Segundo field is about 14 miles southwest of the central portion of the city of Los Angeles, immediately adjacent to the town of El Segundo and the Standard Oil Company's El Segundo refinery site. The field is served and bisected by several major highways connecting the beach cities on the west side of the Los Angeles Basin. The exact location of the field and its position with respect to other producing areas is shown on the map covering this portion of the Basin (Fig. I). The Republic Petroleum Co. discovered the first commercial production in the area when it completed its El Segundo No. 1 (sec. 18, T. 3 S. R. 14 W.) at a depth of 7402 ft. on Aug. 24, 1935, flowing at the rate of about 400 bbl. per day, 28" gravity oil. The producing horizon in this well consists of about 72 ft. of conglomerate and schist conglomerate situated below the nodular shale (Miocene). The true (or solid) schist (Franciscan) was encountered and penetrated some 20 ft. in the bottom of the hole. This paper gives a report on the history of development and oil production to date, and also submits the writer's interpretation of structural conditions as determined from such development. The limited development, together with the complex and variable nature of the producing horizon, makes any interpretation of the structure at present only tentative, and any forecast for a given well extremely hazardous. History of Oil and Gas Production The El Segundo field has produced approximately 1,920,000 bbl. of oil. It has 27 producing wells and 14 drilling wells or locations. The present daily rate of production is about 13,400 bbl. The production history of the field to date is shown in Table 1. The principal companies operating or owning leases in this field are: Caminol Company, Geo. F. Getty, Inc., Ohio Oil Co., Republic Petroleum Co., Pacific Western Oil Corporation, Royalty Service Corporation, Richfield Oil Corporation, Standard Oil Company of California, The Texas Company, Union Oil Company.

Jan 1, 1938

By William C. Grady

Microscopic pyrites are present in all West Virginia coals. Sizes of these pyrites range from 0.1 µ 500 µ (1/2 mm) , and four types are noted: massive, patches, framboids, and isolated crystals. The relative and absolute abundances of the four types vary from seam to seam, and these distributions have a marked effect on the ease with which a seam may be cleaned of pyritic sulfur.

Jan 1, 1978

By A. M. Gaudin

CHANGES in industrial practice, in plant design, and in research methods which are so clearly to be seen on every hand, have affected the mineral industry as well as others. In particular, ore dressing has passed through a revolution in practice brought about by the introduction of flotation and other quasi-chemical methods, until it has ceased to be solely the mechanical preparation of ores. In fact, the term "ore dressing" itself is obsolescent, and "mineral dressing" has been growing in popularity. This assures adequate recognition of the fact that mineral substances other than ores, e.g. coals, clays, and cement rock, are treated by the same general methods. As a result of these industrial changes it was felt that a complete rearrangement of the curriculum and laboratories at the Massachusetts Institute of Technology would be ad-vantageous. Such a rearrangement would allow instruction and research to proceed in wider accord with industrial evolution and the needs of our times.

Jan 1, 1942

By E. B. BESSELIEVRE

THE great work of Gorgas in stamping out yellow fever in Panama during the construction of the Canal was one of the chief factors contributing to the ultimate accomplishment of the task, two previous attempts having failed largely through the demoralization of workers by epidemics of contagious diseases. Mining camps, rapidly constructed during the boom days of the rushes to new fields, have been frequent sufferers from typhoid when, as so often used to be the case, little or no attention was given to bacterial examination of the water supply or to the method used for disposing of the sewage.

Jan 1, 1930

NEW MEMBERS The following list comprises the names of those persons who became. members during the period Sept. 10, 1918, to Oct. 10, 1918. ADDISON, HERBERT, Vice-pres. and Mgr., Big Horn Collieries Co., 412 Colorado Bldg., Denver, Colo. ALLAN, .ANDREW, JR A. Allan & Son, Harrison, N. J. AMI, HENRY M., Charge of War Metals and Minerals, British Embassy, Washington, D. C. ALTHAR, HOMER C., Mill. Engr., The Lorain Coal & Dock Co., Bridgeport, Belmont Co., Ohio. BASER, JOHN T Pres., J. T. Baker Chemical Co., Phillipsburg, N. J. BARBA, W. P., Lieut. Colonel, Ordnance, U. S. A., 2301 Connecticut Ave., Washington, D. C. BENSON, JOHN PATS Min. Engr., Aurora Cons. Mines Co., Aurora, Nev., BOSWELL, H. F Resident Inspector, Southern Railway System, St. Louis, Mo. BRAUCHER, PETERS., Foundry Mgr., Philadelphia & Reading Ry. Co., Sixth & Perry St., Reading, Pa.

Jan 11, 1918

By James W. Dally, William L. Fourney, Anders Ladegaard Peterson

For the past 3 years, the authors have been conducting research sponsored by the National Science Foundation (RANN) to improve the process of excavation by drilling and blasting. The approach followed has been experimental where the development of stress waves and fractures initiated at the bore hole have been investigated in order to obtain a complete understanding of the dynamic fracture process. The second step in the approach has been to introduce modifications in the drill and blast procedure which will permit closer control of the fracture process. The laboratory investigations involve high speed photography where the dynamic fracture process is recorded with a Cranz-Schardin 1, 2 multiple-spark camera. The camera is equipped with 16 spark gaps which are pulsed at 25 K volts to produce an intense but very short (0.5 sec) flash of light. The camera is capable of recording 16 photographs of a dynamic event at framing rates which can be varied from 30,000 to 1,500,000 frames per second. The exposure time is sufficiently short to stop motion associated with detonating explosive charges and to make visible the details of the fracture process at a bore hose. The bore hole in a massive intact rock formation is modelled with a two dimensional plate containing a circular hole to represent the bore hole. The model material employed is a transparent polyester known commercially as Homalite 100.* This polymeric material is extremely brittle as evidenced by its extremely low fracture toughness of [ ]. The fracture toughness is a measure of the ability of a material to resist the propagation of flaws or small cracks. In comparison, Schmidt3 has recently measured the fracture toughness of Salem limestone and determined [ ]. Thus, the Homalite 100 should closely model the brittle nature of rock where fractures occur at small flaws and propagate without any apparent plastic deformation. Homalite 100 is also birefringent, which indicates that it becomes optically anisotropic when subjected to either static or dynamic loads. Circularly polarized light is transmitted through the loaded Homalite 100 model in a polariscope4 and the birefringence produces an optical interference pattern which is called a fringe pattern. For dynamic photoelasticity, the multiple-spark camera is equipped with polaroid filters to produce the circularly polarized light required to generate the photoelastic fringe patterns. An example of a singlespark frame showing a fringe pattern from a typical experiment is presented in [Fig. 1]. The photograph was taken 0.000072 sec (72 sec) after the detonation of the explosive charge. The circular fringes are due to the outgoing dilatational or P type stress wave and travel with a velocity of 85,000 in. per sec (2260 m/sec) in the Homalite 100. The P wave is followed by a second lower velocity stress wave known as the shear or S type wave which propagates at a velocity of 49,000 in. per sec (1245 m/sec). In the local neighborhood of the bore hole, several radial cracks are visible. These cracks propagate at essentially a constant velocity of 15,000 in. per sec (380 m/sec) prior to arrest. The fringes about the crack tips and in the local region of the bore hole are primarily due to the residual gases contained in the bore hole after the explosive charge was detonated. Sixteen frames similar to this one are recorded during the experiment to give full field visualization of the dynamic event at 16 discrete times over its duration. The fringe order number N is related to the difference in the principal stresses of and 02 according to a stress optic law4: [ ] where f0 = material fringe value, and h = model thickness. The wholefield dynamic-fringe patterns provide a basis for simultaneously observing the interaction between propagating cracks and the stresses which drive these cracks. Fracture Control Experiments Improvements in the efficiency of the drill and blast procedures must involve close control of the fracture process following the detonation of an explosive charge in a bore hole. By control it is implied that the number of cracks initiated and the location of each crack on the wall of the bore hole can be specified. Control also, involves orienting each crack and maintaining the crack path and velocity until the specified crack length is achieved. If the entire fracture process can be controlled, then rounds can be designed to optimize volume removed. fragment size and minimize costs. One area of blasting where fracture control is vitally important is in underground excavation where the strength and stability of the rock walls must be maintained and smoothness and precision of the walls must be achieved. The smooth blasting method is one of the most commonly employed procedures for achieving some degree of fracture control. In smooth blasting, the central region of material is first removed, and then the final row of closely spaced undercharged or cushioned holes are fired to remove the final volume and produce a smooth wall. In some instances, unloaded or dummy holes between the loaded holes are recommended to guide the fracture plane. This investigation pertained to an evaluation of 3 features of the smooth blasting process. These included (a) the effect of stress reinforcement on fracture by simultaneously firing 2 charges; (b) the influence of a dummy hole on control of the fracture planes between 2 simultaneously fired charge holes; and (c) the influence of dummy hole spacing on fracture plane control.

Jan 1, 1979

By A. J. Shaler, H. Udin, J. Wulff

In the study of the sintering of meta powders, we have come to the conclusion in this laboratory that further progress requires a more basic understanding of the operating mechanisms. This is emphasized in detail by Shaler. He has shown that a knowledge of the exact value of the surface tension is imperative for a solution of the kinetics of sintering. This force plays a principal role in causing the density of compacts to increase.2 Furthermore, a knowledge of the surface tension of solids is also applicable to other aspects of physical metallurgy. C. S. Smith3 points out the relation between surface and interfacial tension and their function in determining the microstructure and resulting properties of polycrystal-line and polyphase alloys. This paper describes one group of results of an experimental program designed for the study of the surface tension in solid metals. As a by-product of this work, considerable information has been obtained on the rate and nature of the flow of a metal at temperatures approaching the melting point and under extremely low stresses, a field of mechanical behavior heretofore scarcely touched by metallurgists. The importance of this additional information to students of powder metallurgy need not be stressed. Theoretical Considerations Interfacial tension arises from the condition that an excess of energy exists at the interface between two phases. Gibbs proves that this energy is a partial function of the interfacial area; thus: ?F/?s = ? where ?F/?s is the rate of change of free energy of the system with changing surface area, at constant temperature, pressure and composition, and ? is the interfacial tension, or interfacial free energy per unit area. If one of the phases is the pure liquid or solid, and the other the vapor of the substance, ? may properly be termed "surface tension," and is a characteristic of the solid or liquid. The attempt of a body to lower its free energy by decreasing its surface gives rise to a force in the surface which is numerically equal in terms of unit length to the free energy per unit area of the surface. Thus ? may be expressed either in erg-cm-² or in dyne-cm-1. Similarly, surface tension may be determined either by a thermo-dynamic measurement of the surface energy or by a mechanical measurement of the surface force. We have chosen the latter approach. Tammann and Boehme4 determined the surface tension of gold by measuring the amount of shrinkage or extension of thin weighted foil at various temperatures and interpolating to zero strain. The method is of questionable accuracy because of the tendency of foil to form minute tears when heated under tension. Their assumption of F = 2W?, where W is the width of the foil, is unsound, as the foil can decrease its surface area by transverse as well as by longitudinal shrinkage. Although their experimentation was meticulous, the paper does not include details of the sample configuration required for recalculating ? on a correct basis, even if such a calculation were possible. In the experimental procedure chosen here, a series of small weights of increasing magnitude are suspended from a series of line copper wires of uniform cross-section. This array is brought to a temperature at which creep is appreciable under extremely small stress. If the weight overbalances the contracting force of surface tension, the wire stretches; otherwise, it shrinks. The magnitude of the strain is determined by the amount of unbalance, so a plot of strain vs. load should cross the zero strain axis at w = F?. If balance is visualized as a thermodynamic equilibrium, the critical load is readily calculated. At constant temperature, an infinitesimal change in surface energy should be equal to the work done on or by the weight: ds = wdl [A] For a cylinder, s = 2pr2 + 2prl [2] If the volume remains constant, r = vV/pl [31 s = 2vpl+2V/l [4] ds = vpv/l - 2V/l²) dl [5] Substituting [5] into [I] gives for the equilibrium load, w = ?(z/rV- 2V/12) [6] and, again expressing V in terms of r and l, w = pr?(1 - 2r/l [7] Here the end-effect term, 2r/l, is neglected for thin wires in subsequent work. Eq 7 can be confirmed by means of a stress analysis. If the x-axis is chosen along the wire, then the stress is 2pr? - w pr² pr2 [8] A cylinder of diameter dis equivalent to a sphere of radius r, insofar as radial surface tension effects are concerned.³ Thus xv = 2?/d = ?/r = sz [9] For the case of zero strain in the x direction, the strain will also be zero in the y and z directions. Since the wire is under hydrostatic stress, Eq 8 and 9 are

Jan 1, 1950

Schedule of Events

Jan 1, 1977