Search Documents

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

By Pei-Yung Huang, C. R. Hayward

In order to understand more fully the actual state of copper lost in copper reverberatory slags, a systematic study on the various reactions between certain metallurgically important copper compounds and synthetic copper reverberatory slags was undertaken by the authors in the Massachusetts Institute of Technology from 1942 to 1945.1 This paper, being only a part of the work completed, is published first because it furnishes the first experimental evidence of the formation of copper ferrite from reactions between cuprous oxide and copper reverberatory slags. Choice of Slag Composition The choice of the composition of the synthetic reverberatory slags to be used was much deliberated. Commercial copper reverberatory slags, neglecting minor constituents, avcrage :2,3 45 to 47 pct FeO; 38 to 42 pct SiO2; 5 to 6 pct CaO; 5 to 6 pct A12O3. Since the ternary system CaO-FeO-SiO2 has been much more thoroughly studied4 and is much simpler than the quaternary system CaO-FeO-SiO2-Al2O3, it was decided to use calcium oxide only instead of calcium oxide and alumina in the synthesis of the slags. Fortunately the composition of the average copper reverberatory slag with calcium oxide substituted for alumina lies in the region of the phase diagram clarified by the investigators. A survey of the phase diagram (Fig I) suggested two compositions: (I) the composition near the invariant point S, which is made up of 46 pct ferrous oxide, 37 pct silica and 17 pct calcium oxide; (2) the composition near the invariant point K with 45.5 pct ferrous oxide, 43 pct silica and 11.5 pct calcium oxide. Composition S has the advantage that the percentages of ferrous oxide and of silica almost exactly coincide with those of the average reverberatory slags, and that of the lowest melting point (1093º ± 3ºC) in the whole ternary system. The calcium oxide content, however, obviously is high. Since we have already substituted calcium oxide for alumina, and since calcium oxide is more basic than alumina, the fulfil- slag is decidedly too basic. Composition K has a slightly higher melting point (1150O + 3OC) and a higher silica content, but this is preferred because the slag is saturated with respect to tri-dymite and thus should not corrode siliceous refractories. Besides, it is less basic than composition S. The filial slag composition, therefore, was chosen to

Jan 1, 1949

By Benny J. Nelson

To obtain information on the effect of gallium upon the corrosion of magnesium alloys, tests were made on the commercial alloy AM52S (Mg-3 pct Al-1 pct Zn-0.2 pct Mn) and experimental

Jan 1, 1957

By Colin M. Sargent

ALTHOUGH annealing twins are frequently observed in many fcc metals, their occurrence in aluminum is relatively rare. ~ahn' in his review of twinning has listed only a few references to observations of twins in aluminum, e.g., Refs. 2 and 3. They have also been shown to occur in evaporated aluminum layers.4 During the present work, several annealing twins were studied in aluminum. The specimens of 1099-grade aluminum had the following thermomechanical treatment: deformed 90 pct by rolling, partially re-crystallized, further deformed 60 pct to a final thickness of 100 p, then annealed for 24 hr at 120°C. This treatment produced several annealing twins—-about ten per electron microscope specimen. The specimens were produced by the window technique and examined in a Phillips E.M. 200 operating at 100 kv. A typical twin boundary is shown in Fig. 1. For several of the twins studied the twin plane could be tilted so that it was parallel to the electron beam, e.g., Fig. 2. The associated diffraction pattern, Fig. 3, shows the twinned relationship between the grains. The twinning plane in each case was (111). Use of a reflection common to both the twin and the matrix,* i.e., using reflecting planes parallel in the twin and the matrix, the coherent twin boundary becomes invisible and only the noncoherent segments of the stepped boundary are seen, e.g., Fig. 4. Trace analysis of the boundaries showed that the long straight portions were invariably the twin plane; i.e., these portions are coherent. The planes of the shorter segments are shown by Fig. 5 to be (551 1, (7111, and {211).

Jan 1, 1969

By Don Simon

In the late 1960s the mining industry was in an apparent slump due to a combination of factors. Enrollment dropped significantly at schools offering mining engineering degrees, resulting in a shortage today of experienced mining graduates to staff middle management positions. How has this limited supply affected salaries? Does the shortage impair the mining industry's ability to respond to national energy needs?

Jan 12, 1979

J. E. JOHNSON, JR., New York, N. Y. (communication to the Secretary*).-The discussion of Mr. Henrich's paper took place at a meeting from which I had the misfortune to be absent, and has just come to my attention. I do not wish to let the subject pass without contributing to it a little information which has come into my possession. In 1912, I published a brief note in the Transactions on The Effect of Alumina in Blast-Furnace Slags, giving in tabular form three typical slags used in iron blast-furnace practice, one of them the high alumina slag of, which Professor Richards speaks. That table is reproduced herewith. TABLE 1.-Composition of Slays. 1 3 3 4 5 6 7 CaO by Neutral Ratio Ratio Ratio Al2z03, SiO2, Differ- Substan- Cat Ca0 a A1203 Ratio Per Per ence, ces, CaO Cent. Cent. Per Per Al2O3 + Sioz Sit: SiO2 Cecil_ Cent. Virginia practice 6.5 36.0 54.0 3.5 1.27 1.6S 1.50 Lake-ore practice 13.5 33.0 50.0 3.5 1.08 1.92 1.51 Special experiment... 36.0 24.7 36.8 3.5 0.59 2.90 1.44 It supplies what seems to me convincing evidence that, for the purposes of the iron blast furnace, alumina can be regarded only as a neutral substance, dissolving in the slag and materially altering its viscosity, but not affecting its chemical activity. In subsequent experience with charcoal furnaces, I found the same rule to hold; that the chemical effect of alumina could be disregarded, providing the ratio of the lime and magnesia to the silica were kept constant. This is exactly the experience which Messrs. Dwight and Mathewson had in copper- and' lead-smelting furnaces. I have never seen any evidence or argument adequate to support the contention of Professor Richards-that the alumina acted as a base in the charcoal iron furnace and as an acid in the coke furnace, and that the function of alumina in iron-furnace slags is inherently different from that in copper- and lead-furnace slags-and I am compelled to differ absolutely with his conclusions in that respect.

Jan 9, 1917

By W. W. Mullins

The development, by the mechanism of volume diffusion, of a grain boundary groove on an interface separating a solid phase and a saturated fluid phase is calculated under the following assumptions: 1) isotropy of the interfacial free energy 's, 2) applicability of the Gibbs-Thompson formula relating curvature and chemical potential, 3) a nearly planar groove surface. The groove profile is found to have a .fixed shape and linear dimensions that are proportional to (time)1/3. The constant of proportionality is evaluated and involves ?s in such a way that the latter my be evaluated from grooving kinetics. A grain boundary that intersects an interphase interface will tend to produce a groove along the line of intersection (Fig. 1). The ultimate motivation for the formation of the groove is the reduction in interfacial free energ that occurs as the grain boundary contracts. Smith has discussed the way in which the free energy of the interfaces determines their dihedral angles at the groove root and has given a detailed analysis of the effect of the dihedral angles upon the nature the microstructures developed in polyphase alloys. Herring2 has extended the considerations to the case in which the free energy of an interface depends on its orientation and has thus added torque terms to the condition for interface equilibrium. Although the grain boundary and the interphase interface may quickly achieve the proper equilibrium angles where they intersect, as determined by the balance of equivalent tensions and torques,"2 the groove will generally continue to grow (though with decreasing speed). Thermodynamically, this continued growth reflects the fact that the lowest free energy cannot be achieved until the entire grain boundary has been eliminated; mechanistically, the growth occurs in response to inhomogeneities of chemical potential that are caused by the constraint of fixed dihedral angles at the groove root. The latter point is illustrated in Fig. 1, which shows that atoms* near the groove are on the convex side of a cylindrically curved surface and therefore have a higher chemical potential than atoms on the flat interface beyond. Thus atoms tend to leave the curved groove shoulders and force the groove to deepen. When both phases are solid additional chemical potential gradient may arise from whatever strain fields are necessary to insure continuity of material across the interface. In the discussion that follows, this complication due to strain will not occur since we always assume one phase to be a fluid and the other a solid. The transport processes that may operate to permit growth of the groove are surface (interface)* diffusion, volume diffusion in the phase on either side of the interface, and evaporation-condensation when one phase is gaseous. (Also a melting-freezing process is responsible for groove enlargement on a solid-melt interface as discussed in Sec. VI). The theory of grain boundary grooving has been discussed in detail for the processes of surface diffusion and of one type of evaporation-condensation.3'4 The theoretical predictions for the mechanism of surface diffusion have been confirmed in an experimental study of grooving kinetics in copper.5 In this paper, the theory of groove development by volume diffusion will be presented. Volume diffusion can occur either by atomic migration in the solid S or by diffusion of S atoms in the fluid phase, or solvent, adjacent to the groove surface. As discussed in Sec. V, volume diffusion in the solid should be less important than surface diffusion in forming a groove. Apart from verifying this statement then, the main interest of the present analysis centers on diffusion in an external solvent. The solvent may be either a liquid (e.g., water, or-

Jan 1, 1961

By H. Buttner, F. H. Udin, J. Wulff

GRAIN boundaries, the interface between adjacent crystals differing only in respective orientation, have been the object of much experimental and moderate theoretical attention for many years. The earlier experimental work was primarily concerned with the effect that grain boundaries have on the physical behavior of metals, while the basic nature of the boundaries themselves drew only secondary attention. A complete turnabout has been witnessed in more recent years, however, as researchers are now undertaking investigations bearing as directly as possible on the character and physical properties of the grain boundary. Quite comprehensive reviews of the past literature on the subject of grain boundaries have been reported on numerous occasions by various authors, and together these references represent a thorough coverage.'-? It becomes evident in these reviews and other papers"" that the properties of grain boundaries can be explained by regarding a grain boundary as a crystalline region of transition between two unmatched grains. Studies show that grain boundaries have a definite interfacial energy. By measuring the geometry about a point where three interfaces meet in equilibrium, the energy of any two boundaries can be measured with respect to the third. If the absolute interfacial energy of one boundary is known, the absolute energy of the other two boundaries can be calculated. This apparently holds true for any system of phases and interfaces.""25 Most studies have been carried out on solid-solid or liquid-solid systems, or systems of both. However, if about the point of intersection one phase is vapor and the other two are disoriented grains, then two interfaces are surfaces, and one is a grain boundary. Investigations leading to relative grain boundary energy for this particular system have been made by Fullman,23 Greenough and King," and Bailey and Watkins." Herring" treats the system mathematically and arrives at an equation, which appears as Eq. 1, in a form consistent with the reference angles indicated in Fig. 1, ( d?1 ?n = x sina + cosa ( ------- 2 ?2 Sinß da + C0Sß (d?2/d As the system of interfaces comes to equilibrium, a groove of angle appears at the intersection of the grain boundary with the surface, an effect first observed by Rosenhain and Humfrey." Eq. 1 is essentially a summation of the vertical components in Fig. 1 set equal to zero, where ?1 and ?2 are surface tension vectors lying along the side of the groove at point 0 in the groove root. The differential vectors represent the forces tending to rotate the surface into a position that will expose a crystal cleavage surface of lowest energy. Chalmers, King, and Shuttleworth- simplify Eq. 1 by assuming the differential vectors equal to zero, ?1 = ?2= ?Surface and arrive at the following equation: ?B = 2?s cos [2] Greenough and King24 use Eq. 2 for determining the grain boundary energy of silver using prepared bi-crystals of known orientation. Bailey and Watkins25 have done the same for copper, as did Chalmers and others on lead. These authors report the grain boundary values as ratios relative to the surface energy. In the above work, the orientation of grains forming the grain boundary in all cases was controlled so

Jan 1, 1954

By J. R. FINLA

THE three great war periods of recent times involving the-chief industrial, commercial, and military nations of the world have been the following: 1. Wars centering around the French Republic and Napoleon Bonaparte, .1791-1815;. involving every nation in Europe, parts of Asia Minor and *North Africa., and the United States of America. 2. Wars in Europe, Asia, and North -America beginning with the Crimean War, 1854-56, the British Empire, France, Sardinia, and Turkey against Russia; the Sepoy rebellion in India, -1857; -war of France . and Sardinia against ..Austria in Italy, .185.9; :the Taiping rebellion in China, 1861; Civil War in , America, 1861-65; French. occupation .of .M Mexico, .1863; Prussian war against :Denmark, :1864; (Prussia and Italy against Austria sand various -south German : states, 1866; :the Franco-German War, 1870.7,1.

Jan 1, 1931

By Ronald E. Versaw

Environmental legislation, both existing and proposed, requires that mills, tailings dams, evaporation ponds, and related processing facilities be located, constructed, and operated within stringent guidelines. An early step in planning a new processing facility is performing a site selection study in which topographic, hydrologic, geotechnical, and environmental parameters are evaluated for several alternate sites. Once a site is selected, then an environmental report, including a description of the proposed action, alternatives, baseline surveys, and discussions of potential environmental impacts, mitigation measures and monitoring programs is required. The federal legislation, siting studies, and environmental studies (along with the implications of these as they affect design) are discussed. In addition, costs for performing these studies and implementing control of effluents are discussed.

Jan 1, 1978

Discussion of the paper of Earl S. Bardwell, presented at the Butte meeting, August, 1913, and printed in Bulletin No. 79, July, 1913, pp. .1429 to 1441. H. O. HOFMAN, Boston, Mass. (communication to the Secretary*) :-It is pleasing to the originators of the planimetric determination of oxygen in refined copper to see that the method has been taken up by a large smelting plant to be used in every-day work after it has been simplified to suit the new conditions. Several years ago Huntington and Desch 1 had improved our mode of working. They projected the developed negative on to a screen, traced the outlines of the picture with a pencil, drew a border, and measured one constituent with. the planimeter. In order to give the work greater precision, they divided the area into squares of 1 cm. side, shaded the

Jan 11, 1913

Mining headlines in 1952 dealt mainly with expansion as the industry aimed for an ever increasing production to meet the nation's needs. Huge sums were expended for equipment, research, and development. Headlines told part of the story. Negotiations between San Manuel Copper Co. and the RFC finally resolved in a $94 million loan for the development of low grade Arizona ores. Magma Copper, parent firm was to supply an additional 8 million. Kennecott Copper Co., deepening its Deep Ruth Shaft of its Ruth, Neyy mine, announced that the shaft would be in full production in 1953.

Jan 2, 1953

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By Robert A. Colten, Frederick C. Hull, Robert F. Mehl

It is known that pearlite forms from austenite by a process of nucleation and growth, and that the rate of formation of pearlite may be described by a rate of nucleation and a rate of growth.l,2 The manner in which these two quantities operate to produce the observed isothermal reaction curve has been analyzed in a paper published in I939.3 Two types of process were described: (I) that in which nucleation occurs at the grain boundaries of the parent phase, with the nodules growing toward the centers of the grains, initially as hemispheres and then after impingement as roughly radial-columnar structures; and (2) that in which nucleation occurs generally, with the nodules growing to full spheres until impingement with other growing nodules restricts growth. Both cases are met in the formation of pearlite from austenite (Fig. I);2,4 the former, occurring near the knee of the S-curve, has been named "grain-boundary transformation," and the latter, occurring at temperatures near Ael, has been named "group-nodule transformation." In developing our knowledge of the factors that determine the rate of formation of pearlite from austenite, it is important1,2 to obtain data on the rate of nucleation and the rate of growth of pearlite. Such data, when obtained near the knee of the S-curve, will furnish information of use in understanding the factors that affect hardenabil-ity; when obtained at higher temperatures, such data will be useful in understanding the behavior of steels that during heat-treatment react to pearlite.2 It is the purpose of this paper to present data on the rate of nucleation and the rate of growth of pearlite in dependence upon composition, grain size, temperature, and the degree of homogeneity of the parent austenite. The studies are restricted chiefly to plain carbon commercial steels." Previous Data on Rate of nucleation and rate of Growth Data on the rate of nucleation and the rate of growth of pearlite have been published by Scheil and Lange-Weise,5 by Mirkin and Blanter,6,7 by Meh1,l and by Dorn, De Garmo and Flanigan.2, It is difficult to interpret the data, for in most cases too little information is given on austenitizing temperatures and times, the state of homogeneity of the austenite (presence or absence of carbide, etc.), austenite grain size, and mode of formation of pearlite at the temperatures given. Except for the approximations of Mehl and the work of Dorn, austenite grain size was disregarded, though it is well known

Jan 1, 1942

By A. L. Moore

KAISER Bauxite Co., a subsidiary of Kaiser Aluminum & Chemical Corp., has been mining and shipping Jamaican bauxite for over a year. On Feb. 10, 1953 the first boat load of bauxite left Port Kaiser, Jamaica, for the company's alumina plant at Baton Rouge, La. To provide its own source of the aluminum ore, a Kaiser Aluminum & Chemical Corp. exploration party started initial reconnaissance in 1947. This work, and subsequent exploration, led to the acquisition of reserves sufficient to warrant a full-scale mining operation for several decades.

Jan 3, 1954

By R. L. Brown, A. C. Fieldner

Committee it supports pioneering research on the development of a coal-burning gas turbine and through the Mining Development Committee it promotes research on a new type of continuous mining machine that operates without using explosives. Other organizations have contributed major publications on fundamental and applied coal research in the last two decades, including the Minerals Industries Experiment Station of Pennsylvania State College, the Illinois Geological Survey and University of Illinois, the University of West Virginia, the University of Michigan, the University of Alabama, the University of North Dakota, the Massachusetts Institute of Technology, the Koppers Company, the U. S. Bureau of Mines, and, in recent years, the Institute of Gas Technology. Engineering development work, which is included in the overall estimate of $20,000,000, is conducted largely by manufacturers of equipment, and this portion of the estimate is difficult to gage. It represents a large proportion of the estimate and probably is too small rather than too large. For example, the development of mobile coal-loading machines and continuous mining machines, outstanding in recent mining research, undoubtedly involved a high cost. Coal Mining From an economic point of view, the greatest research development in the coal industry obviously has been the growing degree of mechanization in mining. The percentage of underground-mined bituminous-coal output mechanically loaded has risen from 3 pct in 1926 to 67 pct in 1949. Coal operators and equipment , manufacturers have united in designing machinery. Loading machines of large capacity and astonishing flexibility are in common use. Shaking conveyors transport coal from producing faces to transfer points from which it may be carried long distances underground and on the surface; and in many mines rubber-tired shuttle cars carry the coal from the loader to the

Jan 1, 1952

Jan 1, 1898

By M. E. Wadsworth, T. L. MacKay

Sintered UO, samples were leached in sulfuric acid solutions of various concentrations. A pressurized system was used so that it was possible to investigate the kinetics of the reaction to 270°C with oxygen overpressures as high as 900 psi. The rate was observed to be a function of the concentration of hydrogen ions and directly proportional to the partial pressure of oxygen. Evidences are presented which indicate that a UO2 surface site reacts with a molecule of water to form a hydroxyl complex which in turn can dissociate with the characteristics of a weak acid. A rate determining step has been proposed which involves the reaction between an oxygen molecule and the hydroxyl complex on the surface of UO,. ThE 2 principal methods for uranium dissolution are carbonate and acid leaching. The sulfuric acid leach is the more popular and is used for the treatment of the majority of the ores of Africa, Canada, and the United States. Low recoveries in basic leach circuits led investigators at the University of British columbia1 to study leaching of uranium ores in pressurized vessels. Early in the study of dissolution of uranium it was found that only uranium in the hexava-lent state could be leached in acid or basic circuits. Therefore, the use of oxygen over-pressure in an autoclave offered an interesting approach to solving the low recovery problems of carbonate leaching. UO, was used in this study because it could be obtained in high purity and also because it is representative of the most refractory of the primary uranium minerals. A pressurized system was used to provide a means whereby important temperature and pressure parameters could be varied for the evaluation of the kinetic processes. The mechanism for the dissolution of UO2 should be similar for any of the uraninite type minerals. At the present all of the kinetic studies that have been conducted have been in carbonate media. Peters and Halpern2 carried out a kinetic study of the leaching of pitchblende. Their specimens were pitchblende ores selected on the basis of high grade and homogeneity. Pearson and wadsworth3 conducted a kinetic study of the dissolution of UO2 in carbonate solutions with results very similar to those obtained by Peters and Halpern. EXPERIMENTAL The UO2 as received* was found by spectroscopic *Mallinckrodt reagent, supplied by the Atomic Energy Commission. analysis to have a purity of 99.94 pct 0.03. It was ground in a mechanical agate mortar and screened through a 400-mesh sieve. Thin flat disks of UO2 were prepared by pressing the sized powder in a specially constructed die at a total pressure of approximately 25 tons per sq in. The pressed disks were approximately 0.25 cm thick, 1.6 cm diam, and 3.5 g in weight. As pressed, the samples were approximately 65 pct of theoretical density. It was essential that a binder such as poly-vinyl alcohol be added before pressing to prevent formation of cracks when fired. It was found by trial and error that pressed disks sintered close to 1870°C in a hydrogen atmosphere, reach densities between 91 and 91.5 pct of the theoretical density. At this density the samples had no measurable porosity based upon a 2-hr emersion in boiling water. An X-ray examination of these sintered UO2 disks showed them to be identical with the original UO2 received. Reaction of UO2 with the alundum furnace core was prevented by placing molybdenum between the samples and the core according to the method of Corwin and Eyerly.4 Leaching studies were carried out in a specially designed autoclave, the details of which have been presented e1sewhere.6 The main features of the equipment as applied to a kinetic study are: 1) solution samples may be removed during the course of a single run; and 2) temperature and agitation are carefully controlled. Two-ml samples removed from the autoclave during the course of a run were analyzed for U3O8 content with a Beckman model DK-2 spectrophotometer by the method of

Jan 1, 1959

By Brian Mason

Wire Ropes in Mines. Proceedings of a conference held at Ashorne Hill, Leamington Spa, Warwickshire, September, 1950. Published by the Institution of Mining and Metallurgy, Salisbury House, London, 1951. 828 P. $7.00-The volume contains 18 pages on the manufacture and properties of rope wire and wire ropes. In addition, wire rope practice in Britain, Ontario, the Witwatersrand, The United States, South Africa, and other countries are discussed. Testing, government regulations, and inspection are also treated. The book contains a three day discussion on these subjects complete with a summary of conclusions and recommendations. Heating Ventilating Air Conditioning Guide 1952. Published by the American Society of Heating and Ventilating Engineers, New York, 1952. 1496 P. $7.50.Contains a technical data section of reference material on the design and specification of heating, ventilating and air conditioning systems. Also has a section containing information on equipment and manufacturers. An index to technical and equipment sections is included.

Jan 1, 1952

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970