Search Documents

By John T. Galey

The outstanding developments of the year in southwestern Pennsylvania were the establishment of the Summit Fayette County gas pool and the gas pool in Nicholson township, Fayette County, and Monongahela township, Greene County, as major producing areas, and the indication of four new shallow gas pools. Curtailment of drilling for shallow gas is expected to follow order M68 of the Office of Production Management. Gas completions were approximately 70 per cent higher, oil completions nearly 25 per cent lower, dry holes were unchanged and drilling wells as of Dec. 31, 1941, nearly loo per cent higher than last year. Shallow Development Oil.—Outside Butler County, only 11 producers were drilled, with a total initial of 221 bbl. The best of these was in a portion of Gilmore township, Greene County, which ordinarily produces gas. This well flowed 77 bbl. in 11 hr., along with about one million cubic feet of gas from the Fourth (U.Dev.) sand. Washington County had a 10.20 and a 25-bbl. well in Morris township and a 20-bbl. well in South Franklin township. These were all in the Fifth Sand. The price of oil to Jan. 27 was $1.80 per barrel, when a 15¢ increase was made. This was followed by a raise of 20¢ on Apr. 23, 15¢ on May 21, 20¢ on June 18 and 25¢ on Aug. 14. The last increase was canceled on Aug. 23 by the Office of Price Administration, which pegged southwestern Pennsylvania crude at $2.40 per barrel. Gas.—An almost doubled initial production of natural gas is the result of the large increase in number of wells drilled. The outstanding discovery of the year was in the vicinity of Armbrust, Hempfield township, Westmoreland County, where a well drilled to what at first was considered the Bayard sand, but what is now known to be the Fifth (U.Dev.) sand, at 2100 ft. found nearly 5 million cu. ft. of gas. Since this completion 14 wells have been finished, only one of which was dry, giving a combined total open flow of approximately 15 million cu. ft. The sand is 35 to 40 ft. thick and the saturation extends through most of that thickness. Rock pressure, which is 1040 lb. per sq. in., is abnormally high. An area of only about one square mile has been proven but some of the 24 new wells drilling as of Dec. 31 will no doubt extend it considerably. This development has taken place in an area heretofore considered to have had little prospect. There were three good wells in other parts of Westmoreland County. One well in Franklin township, which had 12 million cu. ft, of gas in the Fifth sand, was entirely surrounded by dry holes but is still pro- . ducing at a high rate. In Bell township a 1.6 million cu. ft. well was found in the Speechley (U.Dev.) sand and in Washington township the same sand produced 2.7 million cu. ft. with shut-in pressure of 970 Ib. at 2820 ft. This well is offset by two dry holes and one well with a capacity of only 10 M cubic feet.

Jan 1, 1942

By F. E. Bash

Constantan is an alloy of copper and nickel that is extensively used, under a number of trade names, as a resistance wire with a low temperature coefficient of resistance, and one of the elements of base-metal thermocouples, iron usually being the other thermoelement, although for low-temperature work copper is also used. Before the war, constantan was imported, in common with many other technical necessities. Since it required considerable time to receive the constantan after it was ordered, fairly large stocks were kept on hand; but after the beginning of the war no more was imported and the stocks of foreign material were exhausted about the same time that the steel and munition manufacturers began to need great quantities of it for thermocouples for the heat treatment of steel. To meet this demand, the International Nickel Co. began manufacturing constantan that met all the requirements of the users of resistance wire but did not give the same electromotive force against iron as the German material and consequently could not be used with instruments calibrated for a definite e.m.f.-temperature relation. It so happened that all the constantan made had an e.m.f. lower than that necessary to meet the specifications of the Leeds & Northrup Co. for whom this investigation was carried out. If some had been higher and some lower, good wire could have been obtained by a process of selection, but as it was no wire at all could be procured. To remedy this situation, a thorough investigation was started with the close cooperation of the International Nickel Co. and the Electrical Alloys Co. The specifications to which the constantan had to conform were that it should give an e.m.f. of 47.40 millivolts against pure iron at 1500" F. (816" C.) with the cold-junction temperature at 0" F., or a proportional e.m.f. at temperatures near 1500" F. The method of checking a wire was as follows: It was first welded to a piece of iron wire; Armco iron was found to be satisfactory but iron with greater than 0.1 per cent. carbon would give a lower e.m.f. against the same piece of constantan than pure iron. The couple was then insulated and the fire end was tied to the

Jan 1, 1921

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By R. R. Knuckey

Having been associated with the operation of the de Vooys process for coal, which has treated 13,000,000 tons per annum, and recognizing the process as of value in ore sorting, Huntington, Heberlein and Co. Ltd. (Great Britain) in 1936 made an examination of all other existing methods. In none of the pioneer applications had recognition been given to the necessity for maintaining certain conditions that are essential for sorting certain ores if a truly efficient separation by gravity alone is to be assured. Consequently, in 1936-1937 Huntington, Heberlein and Co. Ltd., with Pearson, employing certain ideas connected with the de Vooys application, commenced the development of a separator that would allow conformance with optimum conditions in the zone where separation is effected. Later, Holt and Wade added to the value of the original application by Wuensch, Rakowsky and others, whose conceptions are being successfully operated today. Meantime, Trostler had enhanced the value of the original H-H. process by improvements that are now embodied in operating plants, and today the process incorporates an improved apparatus and a stable medium that produce the optimum conditions for separation. These conditions are: 1. Elimination of disturbing currents in the separating zone; 2. Reduction to a minimum of medium-density differences throughout the separating zone; 3. Stable medium of minimum viscosity to permit the unretarded fall of mineralized particles; 4. Removal of products of separation with minimum disturbance to the separating zone. Design of Separator The H-H. sink-and-float separator consists of a pyramidal tank in which the separation actually takes place, connected at the bottom with an inclined bucket elevator. The tank and the elevator are filled with medium to within a few inches of the top of the tank. Medium is fed into the separator at a variety of points, according to the type of ore being treated, and it is withdrawn from the separator at two points: (1) together with the float product, by means of a variable-speed addle, at the surface of the medium, and (2) by flowing over an adjustable weir cut in the side of the elevator casing. The prepared ore is fed onto the surface of the medium. The intermediate paddles, which revolve at a slow speed of 2 to 5 r.p.m., move the floating ore across the bath from feed end to float-discharge end. The ore, which is heavier than the medium, sinks below the sweep of the addles and reaches the boot of the bucket elevator, which discharges it without disturbance of the separating zone. These arrangements for withdrawing medium from the separator allow the use of minimum flows, which connote minimum

Jan 1, 1947

By Strathmore R. B. Cooke, Paul B. Queneau

The kinetics of the dissolution of scheelite in basic solutions of carbonate and fluoride were investigated. Work was also done with solutions of alkali metal chloride, hydroxide, phosphate, and mixtures of phosphate and fluoride. The study was conducted at 90 psig and at temperatures ranging from 100" to 155"C, and both natural and synthetic scheelite single crystals were used. The interaction of scheelite with carbonate solutions generally followed a parabolic rate law, and resulted in the formation of calcite crystals on the attached surface. The transport of the CO3 through the calcite to the scheelite surface was probably rate -controlling between 115" and 135°C. Positive deviations from Parabolic behavior were observed at 100" and 155?C, presumably due to the calcite grain growth, and to the formation of a noncoherent calcite layer, respectively. The leaching of scheelite with alkaline fluoride solution produced a calcium fluoride reaction-product which covered the surface as a sheet-like layer. Below 110°C the dissolution rate was parabolic; at 115" and 135°C it was linear. In the linear region, the periphery of the calcium fluoride layer lifted from the sample. Only the lower layers, braced by the scheelite substratum, remained unbroken. This bound layer, approximately constant in thickness, limited the rate at which the fluoride could attack the scheelite. The phosphate and phosphate-fluoride leaches dissolved scheelite at a linear rate; solid reaction products were respectively hydroxyapatite and fluorapatite. Sodium hydroxide and chloride were not effective leachants, and did not produce observable solid reaction products. THE feasibility of pressure leaching of scheelite pulps with basic solutions containing either carbonate or fluoride ions, as indicated by the following equations, has been established by previous investigators:1-3 200°C CaWO4s + CO37q - CaCO3s+WO4aq [1] 200°C CaWO4s + 2Faq ^ CaF2s+WO4aq [2] It is to be noted that a commercial process employing reaction [I] is in use at Union Carbide's operation near Bishop, Calif. In the earlier work referred to, it was apparent that the precipitation of the solid reaction-product on the scheelite particles sharply reduced contact of the leachant with the scheelite. We have extended this work by studying the kinetics of dissolution employing single crystals of scheelite of known exposed surface area. In addition, the effectiveness of solutions of phosphate, of phosphate with fluoride, and of chloride and hydroxide as leachants for scheelite have been investigated. EXPERIMENTAL Apparatus. The low-pressure autoclave used in this wo (100 psig maximum) is essentially that of J. Halpern4 as modified by F. A. Forward.5 Constructed entirely of 316 stainless steel, its maximum capacity is 4000 ml. The temperature in the autoclave was regulated to *0.5?C by a Wheelco thermocouple controller. A 4-in. diam, three-bladed impeller, circulated solution upward against the sample, and a strobo-scope permitted holding the stirring rate to *15 rpm. A check valve and a "pop" type safety valve were installed, a sample holder was fixed to an externally adjustable rod, and a water-cooled condenser was placed in series with the sampling valve. The stainless steel sample holder, Fig. 1, held the epoxy-mounted sample (f) five mm above the impeller. Tightening the tapered sleeve (d) positioned the epoxy-resin specimen-mount by forcing it back against the spacer (c). The mount (e) was 1 in. diam. Sample Description and Preparation. Both synthetic and natural scheelite crystals were leached. The former were single crystals of 99.95 pct purity which were leached approximately perpendicular to the "c" axis; they were supplied by the Gallard-Schlesinger Chemical Manufacturing Corp. The natural crystals, supplied by Minerals Unlimited, were transparent, analyzed 99.8 pct CaWO4, and in ultraviolet illumination exhibited the characteristic blue glow of substantially molybdenum-free scheelite. To permit exposure of an essentially constant surface area of scheelite to the leachant, the samples were mounted in Scotchcast Brand Resin No. 250 (Minnesota Mining and Manufacturing Co.). The mount-

Jan 1, 1970

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By Felix E. Wormser

REGISTRATION started bright and early Monday morning in the Silver Corridor at the Waldorf-Astoria with Mrs. W. H. Bassett as chairman. What a registration-over 200 ladies! Several joined us from as far away as California and Washington State. Apparently they enjoy our meetings so much that present travel inconveniences didn't discourage their coming. At noon the ladies joined the men at the All-Institute Luncheon and Monday evening we had our informal dance, which is separately reported. Tuesday morning was devoted to our annual meeting at which all Section annual reports were read. At noon we were all the guests of the W.A.A.I.M.E. at a luncheon at the Port Arthur Restaurant on Mott St. in Chinatown. Many of us rode down on the old 3d Ave. elevated railway-the last of four. It, too, is soon to be torn down. The luncheon was delightfully unusual, with huge dishes of delicious Chinese food on each table. Our chairman, Mrs. Read, who lived in China in her youth chose our menu, and she chose it well, for most of us indulged so heartily that as we arose from the table we felt we couldn't eat again for 24 hours. Someone donated sherry wine, and boxes of Chinese pencils as favors. We wonder who? All owe a big vote of thanks for this lovely party to Mrs. T. T. Read and Mrs. H. A. Prosser, chairmen, and Mrs. H. W. Hardinge, Mrs. R. Hursh, and Mrs. R. L. Lloyd, vice-chairmen.

Jan 1, 1944

By D. R. de Fontaine

By computing the values of the resolved shear stress for a great many orientations of the tensile axis on all 12 (111) <110> slip systems, Taylor and Elam&apos; were able to map out a stereogram of slip systems, given here, Fig. 1, in Diehl&apos;s notation (see, for example Hauser and Jackson&apos;). The purpose of the present note is to derive such a stereogram by mathematical reasoning and to give a simple method of defining the system with highest resolved shear stress for any direction of the tensile axis, thereby eliminating tedious computation of the Schmid factor. Let the tensile axis, of direction cosines [xyz], make the angles 0 and relative to the slip plane normal [HKL] and the slip direction [hkl] respectively. Fig. 2 shows a simple cubic cell whose edges define a Cartesian coordinate system. Let A be a unit vector of origin 0 supported by the tensile axis. Its end point [xyz] then lies on a sphere of unit radius, on the positive hemisphere of which the planes z = 0, x = y, y = z limit the so called primitive triangle of a standard [loo] stereographic projection. For any point of this triangle, the following hold: 0«2 «y *sx « 1 [l] Now, for given [xpz], the most highly stressed system will be the one for which the following expression of the Schmid factor has the largest possible value: (HKL) belonging to the form (111) and [hkl] to the form <110>, the denominator on the right hand side of Eq. [2] is equal to 1.fi.a. The unknowns H, ... h, . . . can now be determined by correctly distributing +1 and -1 to H, K, L, and +1, -1,O to h,k, 1 giving the numerator of Eq. [2] its greatest positive value (the angles 0 and cpare chosen acute) subject to the condition: Hh+Kk+Ll = 0 [3] since the slip direction must lie in the slip plane. Condition [3] can be satisfied only by having one of its terms vanish and the other two equal to +1 and -1. Taking the case of the tensile axis lying in the primitive triangle, x2y, z and therefore Hh will be chosen equal to +1 with H = h = +1 in order to retain a maximum of + signs. There remain two alternatives: either 1 = 0 or k = 0. 1) take 2 = 0 Then Kk = -1 and the numerator of [2] becomes: Retaining a maximum of + signs gives L = k = +1 and becomes: 2) take k = 0 Then L1 = -1and, likewise, the numerator of [2] becomes: xz - z2 + xy + yz [5] But the difference [5] - [4] can be written: (y - z)(x+y +z) [6] positive or zero by virtue of [I]. If [6] is positive (y > z), then the largest possible value for the numerator of [2] for any xyz inside the primitive triangle is given by [5], i.e., for: That is to say, the active slip system corresponding to an orientat:~on of the tensile axis inside the primitive triangle is:

Jan 1, 1962

By E. J. Dulis, G. V. Smith

AS reported several years ago,&apos; nitrogen may be taken up from the atmosphere by austenitic Cr-Ni steels during creep or creep-rupture tests. This was indicated by chemical analysis and by the appearance of a new microstructural phase, or phases, tentatively identified as chromium nitride (S), at the surface or at the intergranular cracks associated with fracture. The nitrogen pickup was observed to be dependent on time, temperature, and deformation. In a more recent investigation, a sample was obtained in which there was sufficient of the precipitate to suggest that it could be readily identified by X-ray diffraction. This sample had been taken from a 1/4 in. diam creep-rupture specimen of annealed, type 304L stainless steel of the following initial composition: C, 0.03 pct; Mn, 0.65; P, 0.010; S, 0.019; Si, 0.54; Cr, 19.50; Ni, 12.02; N, 0.031; and Al, 0.005. The specimen had ruptured after 10,470 hr at 1500°F (2000 psi). In this case nitrides were distributed across the whole section of the sample, Fig. 1. The precipitate occurred both at the grain boundaries and within the grains; the latter precipitate had in some cases the appearance of pearl-ite, and in others was distinctly Widmanstatten. Chemical analysis of the sample after test showed 0.64 pct "soluble" nitrogen (soluble in 1:1 hydrochloric acid: water) and 0.18 pct "insoluble7&apos; nitrogen (insoluble in the hydrochloric acid solution but dissolved by fuming sulphuric acid). For identification of the precipitate by X-ray diffraction, the matrix in the surface layer of the specimen was dissolved by prolonged attack in an alcoholic solution of picric and hydrochloric acids. The appearance of the specimen surface after such etching is shown in Fig. 1c. The diffraction pattern of the surface-concentrated precipitate was obtained with a recording spectrometer in both the forward and back-reflection regions (the latter by adapting a special fixture to the conventional X-ray unit). The observed X-ray diffraction lines, Table I, show the presence of Cr,N and CrN; the agreement with interplanar spacings calculated from reported data2,3 is quite good. Since it has been suggested&apos; that CrN dissolves only in concentrated sulphuric acid, whereas Cr2N dissolves in dilute hydrochloric or sulphuric acids, an effort was made to distinguish between the two nitrides. This proved possible, inasmuch as etching in a dilute solution of hydrochloric acid gave a sample in which microscopic examination showed that much of the Widmanstatten-pearlitic precipitate within the grains had been eaten out, leaving the grain boundary precipitate in relief, and which, when examined by X-ray diffrac-

Jan 1, 1953

By C. E. Birchenall, R. H. Condit

THREE surface activity procedures are in com--L mon use for the determination of diffusion coefficients in solids. In the oldest of these&apos; the activity observed at the original surface is compared before and after diffusion, where all the activity is in a thin, plated layer on the surface before diffusion. Partial absorption of the radiations from active atoms which have diffused below the surface reduces the effective activity after diffusion. The formula employed to calculate the diffusion coefficient is where F, is the ratio of final to initial activity at the surface, measured with identical counting geometry; Z=u3Dt, where D is the diffusion coefficient; t is the diffusion time; and u is the absorption coefficient for the radiation in the solid as defined by Lambert&apos;s law. This absorption law implies that all the rays are parallel to each other and normal to the specimen surface. This assumption of a collimated beam used by Steigman, Shockley, and Nix has been adopted by all other investigators and, although it gives results which are approximately correct under restricted physical conditions, it does not represent many actual circumstances. It is the purpose of this paper to show the importance of the divergent rays and to indicate a procedure for taking them into account. In the residual activity method the activity is determined on a series of surfaces ground on the specimen at progressively greater depths in the diffusion layer parallel to the initial surface. Gruzin2 has de- rived a formula for this procedure, which may be put in the form where I is the ratio of the activity measured at a newly ground surface at distance k below the initial surface to the activity at the initial surface measured after diffusion, and K= k/2p Dt. A third procedure involves the autoradio-graphic determination of activity on a plane ground at a small angle to the initial interface through the penetration zone. Aut oradiography can be particularly sensitive to the oblique rays. Unlike most counters which detect essentially all ß particles or X-rays which enter the active volume as a single event, the photographic emulsion may be thin enough so that oblique rays with longer path length in the emulsion produce more darkening than rays which move normal to the film plane. Consider a plane containing a source of radiation uniformly spread over a circle and a point counter located on the perpendicular through the center of the circle. As the counter moves along this line, the total angle 6, at the counter subtended by the specimen will vary. For a fixed counter distance, let 6 be angle between the counter axis and the line connecting the counter to a point P on the active plane. If an absorber of thickness X is interposed parallel to the source between counter and source, the ray from point P to the counter will pass through an absorber thickness X secant 6. Exponential absorption is assumed to hold for all rays. If r, is the ratio of intensity at the counter with absorber to the intensity without absorber and a = pX, 1 00 The behavior of this integral, evaluated numerically,

Jan 1, 1957

By H. L. Talbot, R. S. Young, A. Golledge

The differentiation of oxidized forms of lead from lead sulphide in complex products by chemical analysis is of considerable importance to certain mining and metallurgical companies. A method for the separation of "oxide" lead, (non-sulphide), from sulphide lead, based on the solubility of the former and virtual insolubility of the latter in concentrated ammonium acetate solution, has been employed for many years in the industry.1,2 Unfortunately this solvent, while satisfactory for lead sulphate and carbonate, is without action on lead phosphates or vanadates, with the result that at .Rhodesia Broken Hill Development Co. where these latter minerals are present, they have counted as sulphides when using this procedure. For the control of operations in the new concentrator it became necessary to have a closer check on sulphide lead than could be obtained by the only current method of differentiating this constituent from oxidized lead. For some time this problem has engaged our attention, and after a large number of solvents had been tried, the following procedure was evolved. Like all methods depending on selective solution in a com- plex material, it will not give 100 pct separation into oxide and sulphide portions. Because of the ease of oxidation of galena this is almost an impossibility. Our procedure will, however, give a recovery of 99-100 pct of the oxidized lead, contaminated with very small quantities of lead sulphide, and a corresponding recovery of 97-98 pct of the sulphide lead. The procedure is simple and reproducible, and gives results quite .satisfactory for routine control purposes. Experimental For this work standard samples of the following pure lead minerals were obtained from Broken Hill, Northern Rhodesia. These were hand-picked specimens, and were carefully ground to —200 mesh. Since it was realized that a fair-sized sample would be necessary for this work to thoroughly test the large number of procedures we had in mind, a compromise had to be effected between a few grams of very pure minerals and a large sample of lower grade material. For this work the presence of gangue was not deleterious, so long as the oxide lead minerals did not contain lead sulphide, and vice versa. Table I shows the lead minerals used, and their total lead content, both theoretical and actual. Apart from the pyro-morphite the minerals are seen by analysis to be quite pure. Many solutions were tried in an effort to dissolve the oxidized lead minerals and

Jan 1, 1949

By J. Chipman, M. N. Dastur

The importance of dissolved oxygen as a principal reagent in the refining of liquid steel and the necessity for its removal in the finishing of many grades have stimulated numerous studies of its chemical behavior in the steel bath. From the thermodynaniic viewpoint the essential data are those which determine the free energy of oxygen in solution as a function of temperature and composition of the molten metal. A number of experimental studies have been reported in recent years from which the free energy of oxygen in iron-oxygen melts can be obtained with a fair degree of accuracy for temperatures not too far from the melting point. Certain discrepancies remain, however, which imply considerable uncertainty at higher temperatures; also several sources of error were recognized in the earlier studies. It has been the object of the experimental work reported in this paper to reexamine these sources of uncertainty and to redetermine the equilibrium condition in the reaction of hydrogen with oxygen dissolved in liquid iron. The reaction and its equilibrium constant are: H2 (g) + Q = H2O (g); K1 _ PH2O / [1] Ph2 X % O Here the underlined symbol Q designates oxygen dissolved in liquid iron. The activity of this dissolved oxygen is known to be directly proportional to its concentrationl,2 and is taken as equal to its weight percent. The closely related reaction of dissolved oxygen with carbon monoxide has also been investigated:3,4,5 co (g) +O = CO?(g); K _ Pco2___ [2] K2= pco X % O [2] The two reactions are related through the wat,er-gas equilibriuni: H2 (g) + CO2 (g) = CO (g) + H2O (g); K2 = PCO X PH2O [3] PH2 X PCO2 and with the aid of the accurately known equilibrium constant of this reaction, it has been shown5 that the experimental data on reactions [1] and 121 are in fairly good, though not exact, agreement. Experimental Method Great care was taken to avoid the principal sources of error of previous studies, namely, gaseous thermal diffusion and temperature measurement. The apparatus was designed to provide controlled preheating of the inlet gases and to permit the addition of an inert gas (argon) in controlled amounts, two measures found to be essential for elimination of thermal diffusion. A known mixture of water vapor and hydrogen was obtained by saturating purified hydrogen with water vapor at controlled temperature. This mixture, with the addition of purified argon, was passed over the surface of a small melt (approximately 70 g) of electrolytic iron in a closed induction furnace. After sufficient time at constant temperature for attainment of equilibrium the melt was cooled and analyzed for oxygen. GAS SYSTEM A schematic diagram of the apparatus is shown in Fig 1. Commercial hydrogen is led through the safety trap T and the flowmeter F. The catalytic chamber C, held at 450°C, was used to convert any oxygen into water-vapor. A by-pass B with stopcocks was provided so that the hydrogen could be introduced directly from the tank to the furnace when desired. From the catalytic chamber the gas passed through a water bath W, kept at the desired temperature by an auxiliary heating unit, so that the gas was burdened with approximately the proper amount of water vapor before it was introdvced into the saturator S. All connections beyond the catalytic chamber were of all-glass construction. Those connections beyond the water bath were heated to above 80°C to prevent the condensation of water vapor. After the saturator, purified argon was led into the steam-hydrogen line at J, and finally the ternary mixture was introduced into the furnace. THE SATURATOR The saturator unit comprised three glass chambers, as shown in Fig 1, the first two chambers packed with glass beads and partially filed with water and the third empty. Each tower had a glass tube with a stopper attached for the purpose of adjusting the amount of water in it. The unit was immersed in a large oil bath, which was automatically controlled with the help of a thermostat relay to constant temperature, ± 0.05ºC, using thermometers which had been calibrated against a standard platinum resistance thermometer. The performance of the saturator over the range of experimental conditions was checked by weighing the water absorbed from a measured volume of hydrogen; the observed ratio was always within 0.5 pct of theoretical.

Jan 1, 1950

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By A. R. Troiano, R. F. Hehemann

The influence of partial decomposition to high temperature bainite on reaction kinetics at a lower temperature has been studied in two alloy steels. Reaction at the lower temperature is retarded by the prior treatment, and the extent of decomposition may be reduced. Interpretation of these results is based on a mechanism involving a limitation in the nucleation and growth of bainite plates. OF the major transformations in steel, the characteristics and general behavior of the bainite reaction are probably the least understood and appreciated. Limitations of space preclude a critical evaluation of the present status of the bainite transformation in this presentation; however, such a treatment will shortly appear elsewhere. Only the salient features pertinent to the present investigation will be introduced briefly here. Although the reaction curve for the formation of bainite is similar to that for a nucleation and growth process, other kinetic features are more in keeping with the martensitic mode of transformation. A definite temperature exists above which austenite will not transform to bainite.1-5 his temperature, which has been designated B., is determined by the composition of the austenite. Unlike other nucleation and growth processes, the amount of austenite transformed to .bainite is a function of reaction temperature. The extent of decomposition increases from 0 at H. to 100 pct at some lower temperature.&apos; , This lower temperature will be designated B1 and appears to be relatively insensitive to austenite composition.% 5 The similarity in the effect of reaction temperature on the bainite and martensite transformations serves to emphasize the close connection between these two decomposition processes. Austenite decomposition in the bainite range proceeds without partition of the alloying elements.8-11 Partition of carbon has been proposed" primarily on the basis that partial transformation to bainite lowers M, and increases the amount of austenite retained at room temperature. Carbon enrichment resuslting from such partition has been employed to explain the influence of reaction temperature on the extent of decomposition.&apos;" It should be noted, however, that no enrichment has been detected experimentally in high carbon steels.1,14,15 Lattice-parameter measurements of retained austenite in steels containing 0.3 to 0.4 pct C have indicated carbon enrichment, 3,10-18 although the split indicative of a high carbon martensite has not been reported. Carbon enrichment, if it does occur, must be highly localized around the bainite plates. Therefore, carbon enrichment does not account for the influence of temperature on the progress of the bainite reaction."&apos; Thermal history is known to influence the martensite transformation through stabilization.20,21 No similar phenomenon in the bainite transformation has been reported. Materials and Procedure Two triple-alloy steels were chosen for this investigation. Their compositions were as given in Table I. These steels were chosen because the pearlite reaction did not interfere with the bainite reaction. Steel K was received in the cast condition and forged from 2 in. square bars to 1/2 x1 3/4 in. plates. The 4340 was received as 11/4 in. hot-rolled rounds. Both steels were homogenized in vacuum for one week at 2300°F in order to minimize segregation. A quenching dilatometer similar to that described by Flinn, Cook, and Fellows" was employed for the kinetic measurements. Dimensional changes were detected by a differential transformer coupled with a high speed recorder. The dilatometer was mounted so that it could be transferred to any one of three furnaces: a nitrogen-atmosphere austenitiz-ing furnace and two salt-bath furnaces for isothermal transformation. Dilatometer specimens were 1/32 x 1/4x 1/2 in. with a gage length of 1.4 in. All specimens were nickel plated in order to minimize decarburization during austenitizing. The austenitiz-ing conditions consisted of 10 min at the temperatures given above. Austenitizing temperatures were controlled to 210°F and transformation temperatures to ±3ºF. The precision of the dimensional measurements was estimated to be ± 5 x105 in. per in. Results and Discussion Isothermal Transformation: The characteristics of the isothermal bainite reaction will be described

Jan 1, 1955

COUNCIL OF NATIONAL DEFENSE W: S. GIFFORD, Director, GROSVENOR B. CLARKSON, Secretary. The Council of National Defense The Advisory Commission NEWTON D. BAKER, DANIEL WILLARD, Chairman, Secretary of War, Chairman.. (Transportation). JOSEPHUS DANIELS, BERNARD M. BARUCH, Secretary of the Navy. &apos; (Raw Materials). DAVID F. HUSTON, HOWARD E. COFFIN, Secretary of Agriculture. (Munitions, Manufacturing). FRANKLIN K. LANE, HOLLIS GODFREY, Secretary of the Interior. (Science and Research, including En¬ WILLIAM C. REDFIELD, gineerlng and Education). Secretary of Commerce, SAMUEL M. GOMPERS, WILLIAM B. WILSON, (Labor). Secretary of Labor. F. H. MARTIN, (Medicine and Sanitation). &apos; JULIUS ROSENWALD, (Supplies). At the request of Dr. Hollis Godfrey, Chairman of the Advisory Committee On Science and Research, which includes Engineering and Education, a Sub-Committee of Engineering Societies has been appointed with representatives as follows:

Jan 6, 1917

By Stanley D. Michaelson

Stanley D. Michaelson retired in 1976 as chief engineer, Metal Mining Div. and director of the Engineering Center for Kennecott Copper Corp. An active consultant on mining and metallurgical assignments, Mr. Michaelson is also currently adjunct professor of mining engineering at the University of Utah. He received his B.S. degree in mining engineering from Lehigh University in 1934 and an honorary E.M. degree from the Montana School of Mines in 1961. Mr. Michaelson received AIME&apos;s Robert H. Richards Award in 1962 and was named a Distinguished Member of the Society of Mining Engineers of AIME in 1975. He has served as a Director and as a Vice-President on the AIME Board of Directors and is a Past President of the Society of Mining Engineers. He became an Honorary Member of AIME in 1978.

Jan 1, 1979

By Joseph Singewald

THE problem of the utilization of the low-grade red iron-ores has peen before the iron-mining industry of the South for several decades. the experiments by W. H. Coghill1 of the U. S. Bureau of Mines to determine the degree of liberation of minerals in the Alabama low-grade red iron-ores after grinding interest the writer very much because 10 fears ago, while a member of the U. S. Bureau of, Mines, he experimented similarly on the same ores using a heavy solution .2 Extensive experiments were made in the nineties by W. B. Phillips3 in association with H. A. J. Wilkens and H. B. C. Nitze. The ores were rushed to pass 15 mesh and were separated by magnetic machines into concentrates, middlings and tails. The experiments were made with carload lots in an experimental mill. Most of the ores tested, however, were soft, whereas the main problem is the utilization of the low-grade hard ores. Phillips gives the results of only four tests of hard ores; two of these are of self-fluxing ores of the grade now utilized and two of ower grade and less amenable to concentration than the average low-grade ore that underlies the self-fluxing ore of the Big Seam. The average of these least favorable samples shows the production, from an ore analyzing 32.30 per cent. Fe, 10.34 per cent. CaO, 33.40 per cent. insoluble, of a concentrate with 43.82 per cent. Fe, 8.90 per cent. CaO, 18.48 per Sent. insoluble with a ratio of concentration of 2 and an iron recovery of 39.2 per. cent. The grade of this concentrate compares favorably with the average grade of washed brown ores of the district which is given by Burchard4 as 45 per cent. Fe, 14.6 per cent. Si02. The slightly lower iron

Jan 2, 1927

By Maurice B. Dusseault, Edo Nyland

Numerous consistent seismic signals are being generated in a pilot fireflood in a 750 m deep high permeability unconsolidated channel sand in Eastern Alberta. The pilot has a central air injection well, eight production wells on artificial lift, and two internally placed observation wells. Surface seismometers and a 12-hydrophone downhole string were deployed to detect seismics signals. Date were collected for 22 hours employing signal-triggered event detectors recording on cassette tapes. Monitoring during twelve hours of steady air injection at 625m3/s yielded a clear event frequency of about 50 events/h. The events were mostly clear compressional wave arrivals originating in the vicinity of the firefront. Stopping air injection caused a gradual drop in event frequency, and the rate was reestablished when air injection was reinitiated. Spectral frequency analysis and knowledge of material properties indicate that the events are shears of a stick-slip nature associated with the strain-weakening behavior of the over-compacted reservoir sands. The event amplitude indicates small-scale shearing, and different amplitudes suggest that planes re-shear with lower energy release levels. The triggering mechanism for shear rupture is high shear stress created by thermal expansion in the area of highest ther- mal gradient. Other enhanced recovery techniques may also produce useful signals for process control. In particular, steam flooding, hydraulic fracturing, and high-pressure injection operations likely generate mappable microseismic events which can be applied directly to production/ injection strategy.

Jan 1, 1982

By R. H. Tien

The accuracy of the method of steady-state approximation applied to the problems of heat transfer involving phase change (London and Seban&apos;s solution) is improved by defining a "modified heat of fusion" which accounts for the effect of specific heat. An analytical expression for this modified heat of fusion is derived in terms of the actual heat of fusion, specific heat, and surface temperature. Numerical solution for the freezing of iron indicates that the ratio of the modified heat of fusion to the actual heat of fusion increases from 1.04 to 1.4 as the surface temperature decreases from 2700° to 1600°F. The heat transfer process accompanying solidification is complicated owing to the moving solid-liquid interface where the latent heat of fusion is released. Exact analytical solution is available only for a few special cases of freezing problems such as Stefan&apos;s1 problem. In a commonly used steady-state approximation method, London and seban&apos;s2 solution, the effect of specific heat is neglected. This approximation, however, may introduce some degree of error in mathematical analysis when the temperature of the solid surface is much lower than the freezing temperature, as in the case of freezing metals. In a recent work by Robertson and Schenck,3 the problem of freezing a semi-infinite region with finite surface conductance was programed in a digital computer through the finite difference method. A family of curves for the correction of the London-Seban solution was given in a dimensionless plot for different ratios of heat of fusion and specific heat effect; it was shown that the London-Seban solution when applied to the freezing of a mild steel slab under some particular conditions gave results in error by about 10 pct in the solidification rate. Although the Robertson-Schenck computer result has improved the London-Seban solution to a great extent, lack of generality and the tedious computing procedure have restricted its application. In this paper a "modified heat of fusion" which accounts for the effect of specific heat is defined, and is used instead of the actual heat of fusion in the London-Seban solution. An analytical expression of this modified heat of fusion in terms of the specific heat, surface temperature, and actual heat of fusion is derived by comparing the solutions of Stefan and London-Seban for the case of freezing of a semi-infinite region with constant surface temperature. It can also be extended to the case with finite surface conductance, and the results show good agreement with the Robertson-Schenck computer solution. The expression of the modified heat of fusion, the accuracy of the London-Seban solution, and the temperature distribution within the solid are presented graphically in dimensionless form. Numerical solution for the freezing of iron indicates that the ratio of the modified heat of fusion to the actual heat of fusion increases from 1.04 to 1.40 as the surface temperature decreases from 2700° to 1600°F.

Jan 1, 1969

By C. Schlumberger, M. Schlumberger

In order to explore electrically a terrain composed of a succession of horizontal beds, a current of known intensity i is caused to flow between two grounds A and B, and the resultant drop of potential , caused by the resistance of the earth, is measured between two given points in the soil, M and N. In practice it is convenient to choose the two points M and N so that they lie on the line AB and their midpoint coincides with the middle 0, of that line, although this is not imperative. When the lengths L and I of the two lines AB and MN are varied, equations are obtained which may be solved for the resistivity p of the subsoil at various depths. Recall briefly that the formula 4 x l gives the average resistivity, in the horizontal direction, of a layer of earth which extends to a depth1 about equal to L/4. This elementary concept is adequate for numerous practical applications. Nevertheless, it must be said that, in many cases, a rigorous mathematical analysis may be made, provided it is always a question of homogeneous, superposed horizontal beds. The authors expect to publish, later on, appropriate methods of calculation for some specific cases.

Jan 1, 1932