Search Documents

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By J. L. Huiatt, G. M. Potter, R. B. Tippin

The US Bureau of Mines and Great Salt Lake Minerals and Chemical Corp. have developed a froth flotation process for concentrating potassium salts from Great Salt Lake solar evaporites containing about 6% K2O. The crude evaporites, which were predominately halite (NaCl) with smaller amounts of kainite (KCl.MgS0, 2.7Hp0) and schoenite KeS0,MgS04.6H,0), were conditioned in a saturated brine solution., thus converting nonfloatable kainite to the floatable mineral schoenite. Schoenite was then selectively floated with a medium-molecular-weight fatty acid. Continuous small-scale pilot-plant testing indicated that 80% of the potassium could be recovered from the crude evaporites in flotation concentrates assaying about 13% K2O.

Jan 1, 1976

By Rex B. McLellan

A simple model for dilute interslitial solid solutions is set up which enables a solubility equation for the equilibrium between the solid solution and the gaseous solute to be deduced. This solubility equation is used to estimate the partial thermody -namic functions of Ag-O and Fe-N dilute interstitial solid solutions from the measured equilibrium between these solutions and the gas phase. It is shown that the partial excess entropy of the solute atom in solution is a vibrational entropy which is due Principally to the oscillation of the interstitial atom and does not arise from electronic or elastic interaction between the solute atoms and solvent matrix. In this work measurements of the equilibrium between dilute solid interstitial solutions and a gaseous phase are used to deduce the important thermody-namic functions of the solid solution with the aid of a theoretical solubility equation formulated from a knowledge of the thermodynamic functions of the gas and a simple model for the solid solution. The quantity of principal interest which is deduced from the equilibrium data is the change in vibrational entropy occurring when a solute atom (u) is placed in an interstial site in the solvent (u) lattice. This paper forms part of a more general study in which the properties of condensed phases are deduced from measurements of the equilibrium between the condensed phase and a gas. Previous investigations have dealt with the equilibrium between krypton and liquid metals,' a pure metal and its vapor,' and dilute substitutional alloys and the vapor,3 and the subject has been popularly reviewed by McLellan.4 In the latter investigation3 the vapor pressures of very dilute Cu-Ag and Cu-Au alloys were measured with a Knudsen cell technique over a large range of temperatures and the analysis of the vapor-pressure data showed that the relative partial excess entropies were large and positive [ds= -Sudk = 30 for Au-Ag alloys and 150 for Cu-Au alloys; these values should be compared to unity, the value assumed for these exponentials in the quasi-chemical theory of solutions]. For many interstitial solutions experimental data is available for the equilibrium between the solution and a gaseous phase, and this can be used to deduce the vibrational entropies of the solute atoms in solution. The general method employed is to calculate the chemical potential of the solute atoms in the gas and equate this to pi, the chemical potential of solute atoms in the solid, which is deduced from a simple model set up for the dilute interstitial solution (in which the solute atoms act as bound oscillators in interstitial sites). This enables a theoretical solubility equation to be set up. In the case of Ag-O and Fe-N solid solutions the solubility c, is found to vary with temperature according to a relation of the type, where PU2 is the pressure of the O2 or Np molecules. Essentially, the theoretical solubility equation enables the parameter A(T), which gives the vibration entropy, and the parameter AH, which gives the energy of solution of a solute atom, to be estimated from the measured variation of solubility with temperature. The solutions treated are dilute enough to enable solute-solute interactions to be neglected so that the partial energy and excess entropy of solution E, and GS are not functions of composition and the configurational entropy is that of a random solution. Large positive values have been found for sxSu this quantity has not been given sufficient consideration in recent work on interstitial solutions and it is felt that the partial thermodynamic quantities of very dilute solutions should be understood before the thermodynamics of concentrated solutions can be fully appreciated. EXPERIMENTAL DATA 1) The Silver-Oxygen System. The measurements of Steacie and Johnson,= using silver foils, indicate that there is a pronounced minimum in the solubility vs temperature curve for O-Ag solutions. Eichenauer and Miiller6 have recently redetermined the solubility of oxygen in silver using a method developed in the investigation of metal-hydrogen systems.7 The solubility determinations were carried out on compact specimens of differing shapes and sizes and the results indicate a much lower solubility than was obtained by Steacie and Johnson with no minimum at 400°C. Subsidiary experiments showed that the erroneous results of Steacie and

Jan 1, 1964

By W. M. Morris

THE volumetric behavior of isobutane at temperatures below its critical temperature has been studied by several investigators. Seibert and Burrell1 measured the vapor pressure of isobutane from the ice point to the critical temperature. Dana and co-workers2 determined among other thermodynamic quantities the density of the saturated liquid and the saturated gas and the vapor pressure from approximately 0° to 130° F. Sage and Lacey3 studied a number of the thermodynamic properties of this hydrocarbon from 70° to 250° F. The specific volume in the gas and liquid region was determined at pressures up to 3000 lb. per sq. in. ? throughout this temperature interval. In addition, the vapor pressures were measured at 30° intervals. These data taken together serve to establish the thermodynamic behavior of isobutane at temperatures between 0° and 250° F. with reasonable accuracy. However, apparently there are no data available at the higher temperatures. For this reason an investigation of the volumetric behavior of isobutane at temperatures between 100° and 460° F. was carried out with apparatus that has been described in another paper (A.I.M.E. Tech. Pub. 1127).

Jan 1, 1939

By Oscar Weiss

STILFONTEIN and surrounding areas gave nega-tive results in all prospecting attempts since about 1904 when Goerz and Co., a forerunner of Union Corporation Ltd., first drilled in the region and on the farm Stilfontein. Subsequent efforts by African and European Investments Co. and Anglo American Corp. from 1934-37 were completely unsuccessful. Holes drilled by these companies on the farms Riet-fontein, Hessie, and Palmietfontein were stopped in the Lower Witwatersrand system without finding payable reefs. The results of gravimeter, ground magnetometer, and aerial magnetometer surveys are presented in the area, in and around the new Stilfontein Gold Mine, in the Klerksdorp District of the Transvaal in the Union of South Africa. The gravimeter and ground magnetic surveys were completed in 1947—48. The gravity anomalies suggested a block of Upper Witwatersrand quartzites faulted-up between denser rocks of dolomite and Ventersdorp lava. Boreholes S.T. 1, 2, and 3 were drilled in 1948 and, after penetrating the dolomite and Ventersdorp lava, entered Upper Witwatersrand quartzites and intersected the Gold Estates Reef and Vaal Reef. Subsequent drilling delineated the suboutcrop of the Vaal Reef and determined the main structure of this horizon. The gold content of the Vaal Reef was highly payable and shaft sinking is now in progress. The Stilfontein Gold Mining Co. has been formed and, up to date, f5,000,000 capital has been raised for plant, shaft sinking, and development. The payable Vaal Reef horizon extends further south from Stilfontein, the reef occurring at increasing depths. It is possible that at least another mine may be established on these deeper horizons. The farm Stilfontein 39 is situated in the Klerksdorp District of the Transvaal. This farm and the surrounding areas have been subjected to repeated programs of prospecting dating back to about 1904, when Goerz and Co., the forerunner of Union Corporation, Ltd., first drilled on the farm and in the surrounding areas. From 1934-37, numerous boreholes were drilled on the neighboring farms, Riet-fontein. Hessie. and Palmietfontein, by African and European Investment Co. and Anglo American Corp. All these efforts were completely unsuccessful, and nobody suspected any possible gold-bearing area on Stilfontein until about 1947, when a gravity traverse run by B. D. Maree on the main road, showed a negative gravity anomaly. During 1947-48, the writer's organization completed gravimeter and magnetic surveys on Stilfontein and Rieffontein. An area of negative gravity anomalies was mapped, and it was suggested that this could be caused by blocks of Upper Witwatersrand quartzites, of the average density of 2.65, faulted up between dolomites and Ventersdorp lavas, the density of both of these rocks being 2.8. Fig. 1 shows the geology of the area as mapped by L. T. Nel of the Geological Survey of South Africa. The boreholes on Stilfontein, with the exception of a single hole of Goerz and Co., were drilled after the completion of the geophysical survey. The grouping of the first boreholes S.T. 1, 2, 3, 4, 5, and 6, clearly shows that these were located in the zone of negative gravity anomalies. Fig. 2 shows the gravity anomaly contours. Fig. 3 shows two sections across the gravity anomaly, together with the corresponding geological sections as obtained from boreholes. The close relation between gravity values and thickness of dolomite plus Ventersdorp lavas is striking. The two latter formations having the same density (2.8), act as one mass as far as gravity effects are concerned. Fig. 4 shows the magnetic anomalies observed on the ground by vertical magnetometers and at 500 ft abbve mean ground level by aerial magnetometer. The latter are anomalies of the total magnetic intensity. The magnetic results show that, on the farm Rietfontein and on the northern half of Stilfontein. Lower Witwatersrand magnetic shales were to be expected at relatively shallow depths. As the strongly

Jan 1, 1952

By Z. E. Arlin, R. D. Lynn

The problem of disposing of excess waste water coming from The Anaconda Co.'s two uranium mills in Grants, N. M., first confronted the company's engineers in 1956. The increased discharge of mill waste water was due to the start-up of a second mill, recently completed to supplement production from a smaller plant which the company had operated since 1953. The waste water is mildly acidic and has a low level of radioactivity due to small amounts of uranium-natural, thorium-230 and radium-226. In addition, it contains large amounts of manganese, iron and the sulfate and chloride salts of sodium, calcium and magnesium.

Jan 7, 1962

By Charles H. Jacoby

In 1774 a Swedish chemist, C. W. Schule, first recognized manganese as an element. That same year Schule's associate, J. G. Gahn, isolated the element manganese for the first time. In 1856 the Bessemer process of steelmaking gave birth to the economic importance of manganese. Later, in 1882, Robert Hadfield discovered high manganese steels. Although the primary use of manganese is in the ferroalloy industry, two additional important uses for manganese are making chemicals and dry cell batteries. Manganese is also vital to plant and animal life. Various chemical compounds of manganese are used in fertilizers, feeds, glass manufacture, paints, varnishes, and for numerous medicinal and chemical purposes. For the study of industrial minerals and rocks, only the chemical and battery grade material is of- concern, but for the sake of comparison, metallurgical aspects are included in this presentation. Although currently the world's largest consumer of manganese, the United States is producing only minor amounts of ore at the present time. This is due primarily to the fact that although huge deposits of manganese occur within our borders, all are of such low grade as to be economically unfeasible to mine. For many years various government agencies and segments of private industry have devoted sizable sums of money and time in an attempt to upgrade ores from the various deposits, and also in an attempt to recover manganese from blast furnace slags. In view of current world prices, and the quantity of high grade material available, there is little likelihood that any of these approaches will be found to be economically feasible in the near future. Geology and Mineralogy Mineralogy There are over one hundred minerals that contain manganese. These minerals vary from those with compositions that are predominantly manganese to those having only minor percentages. [Chemical Mineral Composition % Mn Hausmannite Mn304 72 Polianite MnO2, 63.1 Pyrolusite MnO24 60-63 Cryptomelane KR8O16R (R=Mn) Variable PsilomelaneBa Mn Mn8O16 (OH).45-60 CoronaditePb R8O16R (R=Mn) Variable Hollandite Ba R8O16R (R=Mn) Variable Manganite Mn2O3•H20 62 Braunite 3 Mn2O3•MnSiO3 62 Tephroite 2 MnO•SiO2 54.3 Rhodochrosite MnCO3 47 Rhodonite MnSiO3 42 Spessartite 3 MnO•AI2O3•3SIO2 33.3 WadHydrous Mn OxidesVariable Franklinite(Fe Mn Zn)O(Fe Mn)sO3 Variable Asbolan Cobaltiferous wad Variable AlabanditeMnS63.14] Geology From a geological standpoint most manganese deposits are complex. In general, it can be said that all primary deposits of manganese are carbonates or silicates. The most productive and profitable have been those of sedimentary origin and residual concentrations. Examples of these residual types of deposits are associated with the metamorphosed lodes of Madhya, Pradesh, India, and the lateritic deposits of Orissa and Bihar, India; nodules in the residual clays of the Philippine Islands, US southern Appalachians and Arkansas, Ghana, and Brazil. Sedimentary manganese deposits are best exemplified by the Nikopol district of Russia and the Tchiatouri area of Georgia, USSR. Hydrothermal replacements are characterized by the rhodochrosite deposits of Butte and Phillipsburg, MT. In general, the hydrothermal type deposit has not resulted in any large tonnages being produced, but may have given

Jan 1, 1983

By Norman P. Goss

What would appear to be a very simple process on paper has proved to be overrun with a multitude of unseen difficulties. For more than 70 years attempts have been made to cast metals in a continuous manner, but it has been only within the last Io years that some degree of success has been achieved.1 Historical Development Bessemer's Experiments—Method I Bessemer was the first to try to cast molten metal in a continuous manner. His method is fully described in U. S. Patent No. 49053, issued in 1865. The patent drawing is shown in Fig. I. In this method the molten metal was poured between a pair of rolls of large diameter, which were cooled by water sprays. Means were provided to prevent moisture from coming into direct coptact with the molten metal. The width of the strip was controlled by the flanges. On paper this should work to perfection, but it is beset with many difficulties still awaiting solution. Bessemer failed to reduce his invention to commercial practice. About 1890 Bessemer's method was revived by Norton and associates (U. S. Patent No. 441375). They formed the Fluid Metal Rolling Co. at Maywood, Ill., and spent $250,000 in endeavoring to develop the technique for this simple method. Finally they had to abandon it. Naturally, they did carry the technical development far beyond anything Bessemer had done, but even so it was far from being a useful commercial success. In recent years it has undergone further development by C. W. Hazelett (U. S. Patent No. 2058447), who has succeeded in obtaining long lengths of copper, brass, aluminum, and even stainless steel. He introduced many' ingenious devices but the greatest obstacle still remained—the disintegration of the roll surface when the surface is heated and chilled in rapid succession. Difficulty is also experienced in maintaining a uniform supply of molten metal to the rolls. The patents pertaining to this method would indicate these to be the major obstacles. Experimental work by Mellen—Method 2 A departure from the method introduced by Bessemer, was tried by Grenville Mellen, of East Orange, K. J., sometime between 1914 and 1920, who obtained a number of patents.2 His method is illustrated in Fig. 2. This method failed to make an impression upon the art; however, it is of value in pointing out the difficulties the inventor ran into and the way in which he tried to meet them. The split mold sections form two endless chains. When going through the center of the apparatus, these sections engage each other to form a complete mold. As the engaged mold section moves downward at a constant speed, molten metal is teemed into it. As this is going on, another set of cooperating mold sections move into position on top of the one being filled. The molten metal is teemed into the mold through a silica tube. According to the teachings of this patent, the level of molten

Jan 1, 1945

By David L. Rife

Fluid inclusions have been studied since the mid-1800s. In 1858, the famous English geologist H. C. Sorby, stated that ". . . there is no necessary connection between the size of an object and the value of a fact, and that, though the objects [inclusions] ... are minute, the conclusions to be derived from the facts are great."' This statement philosophically emphasizes why fluid inclusions should be studied. Fluid inclusions supply the economic geologist with "hard" data on the chemical environment and mechanisms of transport for ore fluids. Such studies enable geologists to understand more about their complex nature. The information that can be obtained from fluid inclusions is as follows: 1) Fluid inclusion "filling temperatures" measured with the microscope heating stage, reflect the hotness of an ore fluid at the time of its entrapment and are one of the most accurate methods of geologic thermometry. 2) Ore fluid densities indicate the extent to which ground water becomes mixed with ore fluids. Density is determined from the composition of inclusions, the ratios of gas to liquid (at room temperature), and from

Jan 1, 1973

By C. Grua, M. Gottlieb, E. M. Wewerka

The Purpose of this paper is to present an overview of research underway at the Los Alamos Scientific Laboratory to investigate some of the more attractive options for controlling trace element contamination of coal refuse drainages. * The control methods under consideration include chemical and physical methods to immobilize or remove undesirable contaminants prior to refuse disposal, the treatment of refuse disposal sites with attenuating agents to prevent the discharge of contaminated water, and the direct treatment of refuse drainage as it emerges from the refuse disposal site. The results from these laboratory studies suggest that many of these techniques are technically feasible for controlling trace element contamination of refuse dump drainage.

Jan 1, 1982

By James P. Graham

In this paper the authors present the background information to preheating and its development and describe the facilities available at the British Carbonization Research Association. The results obtained at BCRA including those collected during commissioning of the new plant at BCRA are summarized and reference is made to the research work planned for the next stage. The enlarged test-plant facilities at the British Carbonization Research Association embrace both 10-t (4.2 m high) and 17-t (6.5 m high) test ovens and two types of preheater, the preheated coal being charged by either gravity or pipeline. During the commissioning of the new equipment, an extensive programme on preheating was initiated and the paper includes the results obtained so far. These cover tests on wet and preheated coals and commercial blends, the use of Rosin- and Cerchar-type preheaters and charging by both gravity and pipeline systems to the 10-t and 17-t ovens. Accordingly, for the first time a direct comparison is possible of both the performances of the plants and the qualities of the respective products. The paper also outlines the findings from a study of the carryover of solids during the charging of preheated coal and of the treatment of those solids.

Jan 1, 1977

By Takashi Katsura, Avnulf Muan

Equilibrium relations in the system FeO-Fe2O3 Cr2O3 have been determined at 1300°C at oxygen pressures ranging from that of air (0.21 atm) to 1.5 x 10-11 atm. The following oxide phases have stable equilibrium existence under these conditions : a sesquioxide solid solution with corundum-type structure (approximate composition Fe2O3-Cr2O3); a ternary solid solution with spinel-type structure (approximate composition FeO Fe2O3-FeO Cr2O3) and a ternary wüstite solid solution with periclase-type structure and compositions approaching FeO. The metal phase occurring in equilibrium with oxide phase(s) at the lowest oxygen pressures used in the present investigation is almost pure iron. The extent of solid-solution areas and the location of oxygen isobars have been determined. ThE system Fe-Cr-O has attracted a great deal of interest among metallurgists as well as ceramists and geochemists. Metallurgists have studied the system because of its importance in deoxidation equilibria, ceramists because of its importance in basic brick technology, and geochemists because of its importance for an understanding of natural chromite deposits. Chen and chipman1 investigated the Cr-O equilibrium in liquid iron at 1595°C in atmospheres of known oxygen pressures (controlled H2O/H2 ratios). The main purpose of their work was to determine the stability range of the iron-chromite phase. Hilty et al.2 studied oxide phases in equilibrium with liquid Fe-Cr alloys at 1550°, 1600°, and 1650°C. They reported the existence of two previously unknown oxide phases, one a distorted spinel with composition intermediate between FeO Cr203 and Cr3O4, the other Cr3O4 with tetragonal structure. They also sketched diagrams showing the inferred liqui-dus surface and the inferred 1600°C isothermal section for the system Fe-Cr-O. Koch et al3 studied oxide inclusions in Fe-Cr alloys and also observed the distorted spinel phase reported by Hilty et al. Richards and white4 as well as Woodhouse and White5 investigated spinel-sesquioxide equilibria in the system Fe-Cr-O in air in the temperature range of 1420" to 1650°C, and Muan and Somiya6 delineated approximate phase relations in the system in air from 1400" to 2050°C. The present study was carried out at a constant temperature of 1300° C and at oxygen pressures ranging from 0.21 atm (air) to 1.5 x 10-11 atm. The chosen temperature is high enough to permit equilibrium to be attained within a reasonable period of time within most composition areas of the system, and still low enough to permit use of experimental methods which give highly accurate and reliable results. These methods are described in detail in the following. I) EXPERIMENTAL METHODS 1) General Procedures. Two different experimental methods were used in the present investigation: quenching and thermogravimetry. In the quenching method, oxide samples were heated at chosen temperature and chosen oxygen pressure until equilibrium was attained among gas and condensed phases. The samples were then quenched rapidly to room temperature and the phases present determined by X-ray and microscopic examination. Total compositions were determined by chemical analysis after quenching. In the thermogravimetric method, pellets of oxide mixtures were suspended by a thin platinum wire from one beam of an analytical balance, and the weight changes were recorded as a function of oxygen pressure at constant temperature. The data thus obtained were used to locate oxygen isobars. The courses of the latter curves reflect changes in phase assemblages and serve to supplement the observations made by the quenching technique. 2) Materials. Analytical-grade Fe2O3 and Cr2O3 were used as starting materials. Each oxide was first heated separately in air at 1000°C for several hours. Mixtures of desired ratios of the two oxides were then prepared. Each mixture was finely ground and mixed, and heated at 1250" to 1300°C in air for 2 hr, ground and mixed again and heated at the same temperature for 5 to 24 hr, depending on the Cr2O3 content of the mixture. A homogeneous sesquioxide solid solution between the two end members resulted from this treatment. A Part of some of the sesquioxide samples thus prepared was heated for 2 to 3 hr at 1300°C and oxygen pressures of 10-7 or 1.5 x 10-11 atm. Reduced samples (either iron chromite

Jan 1, 1964

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

By AIME AIME

YALE UNIVERSITY looked like a top-notch school to "Bert" Phillips in spite of the belief that the college in the home town sometimes looks less attractive than a more distant campus. So Bert, a native of New Haven, earned his B.S., M.S., and Ph.D. degrees from Yale. Immediately after Yale days lie served as metallurgist of the Scovill Manufacturing Co., Waterbury, and then went to the Central Research Laboratories of the American Smelting and Refining Co. at Maurer, N. J., where since 1931 he has been superintendent of research. Bert has contributed to metallurgical literature many reports of studies on the constitution and the physical, metallurgy of copper and copper alloys as well as papers on general nonferrous physical metallurgy.

Jan 1, 1938

By George J. Bancroft

It is unnecessary to repeat here the contents of many valuable contributions to this subject which have appeared in the Dansactions and in the publications of the U. S. Geological Survey. As a basis for the further suggestions of this paper, the following are the most important: 1. The investigation of J. R. Don,' showing the gold of certain Australasian veins to have been deposited by ascending solutions, and not by lateral secretion. 2. The theory of Prof. Posepny? distinguishing the vadose from the deep circulation, and ascribing the origin of certain classes of ore-deposits to ascending solutions of the latter class. 3. The theory of Prof. Van Hise,3 as to the underground circulation and the primary enrichment of veins thereby. 4. The paper of Prof. J. F. Kemp,4 showing that ore-deposits are largely the products of " expiring vulcanism." Many. of Prof. Kemp's ideas have been widely adopted by mining men. 5. The theory of secondary enrichment, so lucidly expounded by Mr. S. F. Emmons.V his theory, dealing with the rearrangement of ore-bodies after primary mineralization, has been generally adopted, and seems to me to have been as completely proved as the nature of the case permits. There are two facts which I think should be constantly borne in mind in formulating a theory of the genesis of ore-

Jan 1, 1908

NEW MEMBERS The following list comprises the names of those persons who became members during the period May 10 to June 10, 1914. Members ABE, ASAKA, Chief Min. Engr., Yamagano Gold Mine, Satsuma-Gori, Satsuma, Japan. ANDERSON, FRANK M., Geol Cartagena Refining Co., Cartagena, Colombia, S. A. BACON, MAURICE W., Genl. Mgr Stewart Mining Co. Butte, Mont. BACON, RAYMOND F., Chem Director, Mellon Institute, Pittsburg, Pa. BAKER, HAMILTON WALLACE, Min. Engr Fernley, Nev. VON BAYER, AUGUST HECTOR, Supt Kentucky Solvay, Coke Co., Ashland, Ky. BISHOP, WHEELER SCOTT, Research Chem Care Braden Copper Co., Rancagua, Chile, S. A. BOWEN, CHARLES GILMAN, Timekeeper 208 School St., Grass Valley, Cal. BOYER, SAMUEL L., Mine Operator, Mgr., Mike. Horse Min. Co., W. 2808 Boone Ave., Spokane. Wash.

Jan 7, 1914

By R. M. Treco

THE thermal expansion of pure beryllium was first investigated by Hidnert and Sweeneyl in 1925 on a single cast specimen stated to be of 98.9 pct purity. A study of the coefficients of expansion by X-ray methods has recently been made by P. Gordon' on powder obtained from the Brush Beryllium Co. assaying 97 wt pct beryllium with about 2 wt pct oxygen as an impurity. The present work pertains to about the highest purity metal obtainable from the Brush Beryllium Co. This metal was in the form of lumps which were remelted and cast in a high-vacuum induction furnace. Expansion data in this paper deal with beryllium extruded into bars of rectangular cross-section 4x1/2 in. and the anisotropic expansivity of a large cast single crystal. Analysis of the cast metal after extrusion indicated a beryllium assay of 99.28 pct. Impurities were 0.170 pct Fe, 0.140 pct Al, 0.014 pct Mg, 0.086 pct Si, 0.020 pct Cu, 0.020 pct Mn, 0.007 pct Ni, 0.007 pct Ca, 0.080 pct C, 0.179 pct 0, (as BeO). Part I—Extruded Metal Thermal expansion measurements were obtained with a fused quartz-tube differential type dilatom-eter3 on specimens cut from the extruded sections in longitudinal and transverse directions. Specimens were machined to a diameter of 0.250 in. and a length of 3.000 in. One sample from each direction was vacuum annealed for 1 hr at 800°C. The dilatometer tube was placed in a vertical tube furnace having a uniform temperature zone which was twice the length of the sample. Average time for a complete thermal cycle to 500°C was 18 hr. Temperatures were observed with two chromel-alumel thermocouples attached to the sample about 1 M in. apart. The accuracy of temperature measure-ment was ± 0.25°C. An argon gas atmosphere sur-rounded the specimen to prevent oxidation of the beryllium. Samples were identified as shown in table I. Results - The original plan included measuring expansion up to 1000°C, but the first two runs on sample No. 5 showed that a permanent contraction occurred from

Jan 1, 1951

By F. P. Bullen

Empirical relationships between fracture stress, orientation angle, and diameter of crystal have been determined at 77°K. Orientation ranges of markedly different behavior were found—a law of constant normal stress&apos; of value a (diameter)-1/2 for the fracture of ductile crystals, and a condition of shear stress (or strain) for more brittle crystals. The observations are not consistent with current theories. An interpretation is advanced which is also applicable to observations on the effect of prestrain at room temperature on the subsequent fracture stress at 77°K and to the effect of cyclic stressing on the cleavage strength.&apos;&apos; The law of constunt normal stress&apos; and the brittle ductile transition are also explained. The interpretation is more consistent with the initiation of cracks by intersecting dislocations than with theories based on stress -concentration by dislocation arrays. ZINC single crystals are particularly suited to the study of cleavage because fracture occurs on the basal plane over a wide range of crystal orientations. Analysis of the conditions of stress and strain at fracture in crystals of different orientations should indicate which parameters control the cleavage process. Unfortunately, controversy has arisen over the correct empirical relationship between tensile fracture stress and orientation. Schmid&apos;s observations1,2 favored a &apos;law of constant normal stress&apos;, as observed in other materials.2 For zinc, however, the observed values are far below the theoretical strength and cannot represent the true limit of cohesion between neighboring atomic planes. Hence, the interpretation of such a &apos;law&apos; is not straightforward. Deruyttere and Greenough3,4 found a complex variation between tensile fracture stress and orientation; this variation did not agree with a &apos;law of constant normal stress&apos;. Two theories have been advanced to account for their observations: a) the propagation of cracks from low-angle boundaries,5 and b) the release of energy from piled-up dislocations during crack-propagation.4 The present work resolves the apparent discrepancy between the observations and shows that neither of the above theories are applicable to the tensile fracture of zinc single crystals. A phenomenological explanation, along the lines suggested by Gilman,&apos; is advanced and successfully applied to previously unexplained effects. EXPERIMENTAL DETAILS &apos;Crown Special&apos; redistilled zinc was used, except for one comparison series op tests using &apos;Tadanac&apos; electrolytic zinc. Crystals of 1 mm diam, subsequently called &apos;1 mm crystals&apos;, were grown from the melt in vacuo in precision-bore Pyrex tubes internally coated with graphite. Several specimens 1 in. long were cut from each crystal and chemically polished. Jigs were used to minimize handling strains, and crystals were mounted in the Polanyi machine the day prior to testing to allow recovery from any such strains. One-mm crystals were chemically polished for long periods to obtain 0.1 mm (approx) crystals. One-mm crystals were cemented into miniature gimbals by &apos;Araldite&apos; casting resin. The Appendix gives the reasons for using gimbals and the results obtained by other methods. More complete details of all techniques are given elsewhere.7 The symbols and terminology used are as follows: X = orientation angle (angle between tensile axis and line of greatest slope in the basal plane). T = tensile stress (on true cross-section) S,N = shear and normal stress (components of T with respect to the basal plane) ? = shear strain D = crystal diameter. The subscript &apos;f&apos; will be used to denote values at fracture. PART I-ANNEALED CRYSTALS EXPERIMENTAL OBSERVATIONS One-mm crystals were used to establish the variation of fracture stress at 77°K with orientation at fracture (Xf), Fig. 1. For 18 deg = Xf = 55 deg, a &apos;law of constant normal stress&apos; was observed. For Xf > 55 deg, the fracture condition approximated to a constant shear stress. At Xf< 18 deg, twinning occurred before fracture so that the results were not typical of homogeneous single crystals,4,8— such specimens will not be considered herein. The dependences of fracture stress upon Xf were of similar type for 6 mm,* 1 mm, and 0.1 mm crystals,

Jan 1, 1963

E. O?C. Acker Jinzoc Adachi Truman H. Aldrich Walter H. Aldridge Anson W. Allen John H. Allen William R. Appleby W. Lawrence Austin W. S. Ayres David Baker John Henry Banks Henry C. Banon Alonzo F. Bardwell Walter A. Barrows H.C. Bellinger Wm de L. Benedict Robert Bentley John F. Berry Andrew A Blair George D. Blood Charles A. Bohn Walter M. Brodie Elwin F. Brown Fredrick Burbidge H.H. Burden Charles Butters

Jan 1, 1944

By Joseph P. Hodgson

Since about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develop the different phases of various mining subjects at regular meetings. Nine Foremen&apos;s Dinners In the latter half of 1912, the Copper Queen Consolidated Mining Go. gave monthly dinners to the men in the operating departments. Those who attended were superintendents, foremen, shift bosses, engineers, geologists, and heads of all departments, making a total of about 75 men. After the dinner, lectures were given on subjects which pre-

Jan 1, 1917