Search Documents

By C. M. Shigley

Tan record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.1 The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 t0 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000000-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation-the largest known magnesium plant utilizing sea water as its raw material. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and y miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1945

By J. Weertman

The paper of Gifkins and Snowden considers the interesting but difficult problem of determining the stress dependence of secondary (steady-state) creep at low stresses. These authors have concluded that at stresses below 250 psi (2 x 107 dynes per sq cm) the secondary creep rate of lead is proportional to the stress (viscous creep) and is not proportional to the stress raised to about a fifth power. The experimental data considered by them were obtained on tests conducted at room temperature and at 50°C. The lowest stress employed was 50 psi (3.5 X 106 dynes per sq cm). The authors pointed out the main difficulty in determining the stress dependence of creep at low stresses. The creep tests must be run for very long lengths of time. However they made no estimates of when an experimental creep rate determination must be rejected because it does not represent a true steady-state or minimum creep rate. In order to be certain that a creep curve is within the steady-state region, the total creep strain should be of the order of 0.1 to 0.2. For a creep test of a year's duration this requirement implies that a secondary creep rate smaller than about 10-3 per hr cannot be measured reliably. The corresponding creep rate for a 10-year test is 10-6 per hr. The creep rates of the tests that were considered by the authors to prove the existence of viscous creep were of the order of or less than 10-6 per hr. One can conclude reasonably that this data does not prove unambiguously that large strain steady-state creep rate of lead is proportional to the stress in the stress range of 50 to 250 psi (3.5 x 106 to 2 X 107 dynes per sq cm). Another technique can be used to obtain the stress dependence at low stress levels. The creep rate is a very sensitive function of temperature. The creep rate can be increased by very large amounts merely by increasing the temperature. We carried out steady-state creep tests on lead single crystals25 at temperatures up to 320°C. We were able to obtain creep rate data down to stresses as low as 35 psi (2.5 x 10' dynes per sq cm). Our smallest creep rate was 8 x 10-5 per hr. Thus we obtained large strain, steady-state creep rates to even lower stresses than were considered by Gifkins and Snowden. No evidence was seen for viscous creep. The creep rate was proportional to the stress raised to about a 4.5 power down to the lowest stresses. Since there is no reason to believe that changing the temperature should change the stress dependence of steady-state creep, we feel that large strain viscous creep does not occur in the stress range quoted by the authors for lead single crystals or large-grain polycrystalline samples of lead. This conclusion does not imply that viscous creep may nat occur in a lower stress range or in the same stress range for fine grain material or at creep strains very much smaller than 0.1. Support by the U.S. Office of Naval Research is acknowledged. Authors' Reply R. C. Gifkins and K. U. Snowden We thank Dr. Weertman for his discussion and although, as we hope to show, we do not agree with his reservations, we do concur in stressing the importance of ensuring that creep rates are reliably obtained. Dr. Weertman appears to be content to accept n = 1 for low stresses with fine-grained material but not for single crystals. We believe our results show that the former result cannot be accepted without also accepting the latter. We will also show that the probable errors in our minimum creep rates are insufficient to alter our conclusions, that the criterion proposed by Dr. Weertman is arbitrarily restrictive and his alternative experimental approach possibly invalid. 1) A principal result of our Fig. 1(a) is that n = 1 for polycrystalline specimens at room temperature and 50°C for stresses below -250 psi. There was evidence that crystal slip and grain boundary sliding contributed approximately equaily to the overall strain in this low-stress regime. This implies that either a) grain boundary sliding controls slip within the grains or b) both grain boundary sliding and crystal slip independently occur according to mechanisms which give n = 1. Alternative a does not seem acceptable, so we were forced to consider b. This led us to reexamine work on bicrystals by Strutt and Gifkins and plot curves Fig. l(b). Previously Strutt et al. (loc. cit.), had merged these points with others using the Zener-Holloman parameter and thus, we now believe, had been led to overlook the behavior where n = 1. Curves C and D in Fig. l(b) did appear to confirm the hypotheses that n = 1 for crystal slip at these low stresses and the sliding curve F was similarly of the expected form. It was comparatively easy to find a quantitative theory to account for n = 1 for sliding and the similarity of curves C and D to curve F (all obtained from the same set of specimens) led us to feel that the single-crystal curves were valid. 2) We believe the secondary creep rates for both the polycrystalline and single-crystal specimens to be in error by factors c2. In Fig. 6 creep curves for polycrystalline specimens of lead(1) and lead(II) are reproduced as curves a and b, respectively, and curve c is for a single crystal at 100 psi. It is clear that, although the attainment of secondary creep rate takes 2 years for a and 150 days for b, thereafter the curve is linear for periods of 7 and -1 year, respectively. The single crystal has a linear portion commencing after 20 and extending to 90 days. Creep extension was measured directly using a traveling microscope reading to 0.01 mm on gage lengths marked on the specimens; the gage lengths

Jan 1, 1968

By F. E. Lucas

This paper is offered with considerable diflidence, since some of the statements made may not agree with the opinions of other members of the Institute. What I give is the result of some years of experience in the operation and construction of coke-ovens, and observation of plants in America and Europe. Although my title is " The Manufacture of Coke," I have found it impossible to do justice to the subject without touching on a number of points which, while not strictly involved in the making of coke, yet are of paramount importance from an economic standpoint. There are, indeed, many points of interest, on each of which a separate paper of considerable length might be written, but the scope of my paper will permit me only to touch lightly some of them, in the hope that what I say will promote a full discussion on the whole question. Those of us who are interested in the manufacture of coke are under an obligation to the American Institute of Mining Engineers, which has opened its meetings to the discussion of this subject. I do not believe that there is any question to-day more worthy or more in need of discussion. When geologists and mining-men tell us that, at the present rate of consumption, our coal-fields will be exhausted in a few generations, me should welcome any means that will conserve these deposits as far as possible, and give us the greatest amount of heat or power from every ton mined. I shall try to show that much can be done in this direction through the by-product coke-oven, and that it should stand second to none as an economic factor in the industrial world. I shall here deal exclusively with the by-product oven, except for the comparative statement I hare prepared, showing the saving to be effected by coking in by-product instead of beehive orens. It should be borne in mind that this comparison

Jan 1, 1913

By William D. Manly, John Towers, Paul A. Beck

RECENT work on grain growth in high purity aluminum and in a solid solution type alloy of aluminum and magnesium' showed that the isothermal increase of the average grain diameter D with time follows the equation [D = K(to + A)-Eq I] Here [to] is that portion of the total annealing time [t], which is available for grain growth, i.e. the annealing time less the time necessary for complete recrystallization. The parameters A and n depend only on the temperature. A has the dimension of time, and is usually of the same order of magnitude as the time for recrystallization: R. In some instances R may be substituted for A in Eq I. This is the case for example at long periods of annealing or at high temperatures, where both A and R become small in comparison with t. In such instances Eq I is simplified to [D-K-tnEq2] For high purity aluminum the exponent n increases in the ratio of about 1 to 5 in the temperature range of 350° to 600°C. 70-30 brass has been long known to exhibit grain growth of the continuous type, such as occurs in pure metals. For this reason, it was of interest to determine whether grain growth in brass also follows Eq I and 2 as it does in aluminum. Isothermal grain growth data for 70-30 brass were published in recent years by R. S. French2 and by H. L. Walker3 Fig I shows a log D vs. log t plot of French's data, together with the 500, 600 and 100°C data by Walker for 42.8 pct reduction by rolling. In such a log D vs. log t plot Eq 2 corresponds to a straight line with a slope of n. As seen in Fig I, the data of French and the 600°C data of Walker can be represented by straight lines. However, the 500 and 700°C data of Walker give curved lines and the average slope of his 500°C line is very different from the slope of the line representing French's data for the same temperature. Furthermore the curvature of the 700°C line suggests a tendency for grain growth to stop after 8 hr. If confirmed, this would constitute a definite deviation from Eq 2, not explainable on the basis of the specimen thickness effect found in high purity aluminum.1 Walker's specimens were 0.125 in., i.e. 3.18 mm thick, while the deviation occurs at a grain size of approximately 0.4 mm. A further point of divergence arose recently, when J. E. Burke suggested4 on the basis of Walker's data, that, instead of Eq 2, grain growth in 70-30 brass follows the equation [D-D. =K• t,Eq3] Here D, is the grain size as recrystallized at the temperature in question. Although it was possible to show5 that, for pure aluminum, for which isothermal grain growth has been carefully investigated, Eq 3 is incompatible with the experimental facts, the situation remained somewhat obscure with respect to 70-30 brass. In view of the discrepancies between the

Jan 1, 1948

By H. Becke, D. Stolnitz, D. Flatley, W. Kern

Extensive solid solubilities of CdTe (zincblende-type struckre) and InTe (B37 type) in each of the rock salt-type compounds, PbTe and SnTe, have been observed. Partial phase diagrams have been determined by thermal analysis and X-ray metallography. The limiting mol fraction. X,, of the solute in the rock salt-type a phase and the corresponding eutectic temperatures, T,, are: (PbTe)l-x(CdTe)x: X,- 0.2, T, =866°C; (PbTe),-,(lnTe),: X, - 0.35, T, = 646"C; (SnTe),-,(CdTe),:X,- 0.11, T, = 784 "C; (SnTe),-,(lnTe),: X,-0.53, T, = 630°C. The lattice parameters of the a phase decrease linearly with X, even in (PbTe),-,(CdTe),, where a, (CdTe) = 6.481A > %(PbTe) = 6.459A. This is taken as proof that the cadmium atom enters an octahedral interstice of the tellurium atom sublattice; i.e., the formation of the a phase entails the direct replacement of lead by cadmium. The a, us X curve extrapolates to 6.16A at X = 1, in agreement with the value predicted for an ionic crystal of CdTe; it is also consistent with the reported lattice parameter It is well-established that the compositions of intrinsic semiconducting and semimetallic compounds conform to normal valence rules.1"5 The apparent exceptions can be explained by taking account of anion-anion covalences, as in CdSb, or of multiple cation valences, as in In Te.'This empirical generalization is the basis of the chemical approach to semiconductors2 by which the properties of an intrinsic semiconductor are rationalized in terms of the ionic-covalent bonds necessary to saturate the valence-electron complement of the anion sublattice. A fundamental shortcoming of this approach is its disregard of long-range crystal interactions. It cannot, accordingly, deal with the phenomenon of charge conduction except through the use of ad hoc postulates. As an example, a crystal of CdTe would, in the valence-bond picture: be described in terms of electron pairs, each with the same discrete energy, localized between every cadmium and tellurium atom. This is, of course, contrary to the Pauli of the high-pressure rock-salt form of CdTe, corrected for decompression from 36 kbar. The free energy of formation of the a phase of pure CdTe at room temperature is calculated from the phase diagram to be +10 kcal per g-atom, in accmd with the value calculated from the transformation pressure. The standard enthalpy is +13 kcal per g-atom, and the standard entropy is +9 eu. The latter value implies the formation of extra classical particles, such as vacancies, interstitials, or nondegenerate charge carriers, but these alternatives are not consistent with the semiconducting properties and the densities of the a phase. The extrapolated values of the lattice parameters of (PbTe),-,(lnTe), and Spectively, for the rock salt-type modification of InTe. The corresponding interatomic separation is intermediate between monovalent and trivalent indium. The qualitative implications of the results are considered from the viewpoints of both valence-band theory and energy-band theory. principle, and is corrected by methods of molecular-orbital theory in which bonds are replaced by bands of molecular orbitals whose energies, E, depend upon a crystal-momentum vector, k.7 Each band is derived from a linear combination of atomic orbitals with two electrons required to saturate each molecular orbital in the band. In a crystal of N atoms containing z atoms in its primitive unit cell, there are 2 N/z states per band which lie in a region of k space bound by the Brillouin zone. In an intrinsic semiconductor, the bands can be grouped into valence bands which are normally filled and conduction bands which are normally empty. If the highest valence band and the lowest conduction band overlap anywhere within the Brillouin zone, the material is rendered semimetallic. The quantity defines the effective mass, m*, of an electron in a conduction band (or of a hole, i.e., an electron deficiency, in the valence band) and leads directly to the concept of charge mobility through the relation \x = et/m*, where e is the electron charge and t is the lattice relaxation time.

Jan 1, 1964

CHARLES F. WILLIS,* Bisbee, Ariz.-(written discussion?).-The consensus of the discussion of the paper of Dr. Lanza indicates that the physical examination, while it is probably a good thing, is fought by the workingman, and that, because of this fact, it has been proved unsuccessful. The physical examination standing alone is worth but little, and could easily be made a subject both of ridicule and dissension unless the company having such examination shows its own good faith in promoting a thoroughly better health program. It is easily seen why a workman would resent his employer expecting him to be physically fit, if at the same time the employer provides un-healthful, unsanitary, working conditions, or if the town in which the employees are expected to live is dirty and unkempt. One mocks the other. The employer cannot say, "You must remain healthy so that I can get by with unhealthy conditions." But if working- conditions are as good as can be obtained to keep men well, the employer can ask his men to be in a healthy condition. A State examination and standard would have many difficulties, owing to the fact that a man would pass or would not pass the standard set, thus eliminating the discretion on the part of the employer in placing men whose physical condition might well permit working in one place and not another. Any physical examination that is run for the purpose of eliminating the physically unfit is unjust, both to the worker and to the nation as a whole; a State examination would make a distinct dividing line, whereas examination by the employer is conducted with a vision of the positions available. The workman's opposition to the physical examination comes from the fact that he has been taught to believe that it is an interference in his personal affairs, that he can be clean or dirty as he chooses, that he can he healthy or unhealthy, and that it is nobody's business but his own. The war has taught us, however, that the individual is no longer the unit and that all such propositions must be based on the greatest good for the greatest number.

Jan 6, 1919

By H. H. Einstein

Swelling ground is one of the most feared problems in tunneling. Although usually not causing sudden failures during construction, the very large and longlasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners up to 1 m (3 ft) thickness that have been cracked or crushed, tunnel inverts that are heaving at 0.1 m (0.3 ft) per week during construction and continue to heave during decades. This paper summarizes essential components of design construction procedures where tunnels in swelling rock can be built to perform satisfactorily. It is important to point out that design and construction cannot and should not be separated. The way the tunnel will be built has to be an integral part of the design. Swelling can be defined as time dependent volume increase and is distinguished from squeezing, another time dependent phenomenon occurring in tunneling. Squeezing involves exceeding the shearing resistance while swelling usually does not. Swelling of rock masses can occur as swelling of the intact rock, swelling of wall rock, of gouge and of filler in the discontinuities of a rock mass, and as a combination of the above. Swelling mechanisms have been discussed elsewhere (ISRM 1983).

Jan 1, 1984

By E. H. Citron

CLEANING fine coal in jigs is not new in Europe, where the feldspar jig is being used almost exclusively for this purpose. A feldspar jig operates with an artificial bed made up generally of feldspar or other hard rock material. Dimensions and specific gravity of this material must be of suitable values for good bedding qualities. For good efficiency, the size should range between 1x2 in. and 2x2x1/2 in. thick.

Jan 4, 1958

By R. W. Gurry

THERMODYNAMIC calculations indicate that boron is a better deoxidizer than silicon but probably is not quite as effective as aluminum. Boron should, therefore, be readily oxidized out of the open-hearth bath, which implies that it is not recovered in significant concentration from any scrap charged; also that, if added in the ladle, it tends to oxidize out during teeming unless protected by the presence of a. better deoxidizing agent. These conclusions do not apply to liquid cast iron, in which the oxygen content is much lower than in liquid steel. The possibility of conserving certain strategic alloying elements widely used in steelmaking, notably manganeie, chromium and molybdenum, by the use of boron, which in small concentration appears to be extraordinarily effective in promoting hardenability, raises a question as to what extent any boron present in the scrap charged into the open hearth is oxidized out during melting and subsequent refining. This question is significant because the optimum concentration of boron in the finished steel, which is fairly critical, would be very difficult to attain if the boron in the charge were largely retained in the metal. Moreover, unless boron is substantially eliminated in the open-hearth process its use on a large scale would eventually make it impossible to produce boron-free steel except by restricting the charge to virgin material. There is at present, unfortunately, virtually no satisfactory direct evidence to provide an answer to this question; but there are indications from practice that boron is oxidized out in the open hearth in the production of medium or low-carbon steel, although it may be retained if the carbon content remains fairly high; that is, if the oxygen is kept fairly low. In the absence of direct data, it is necessary to rely upon the indications of indirect evidence, the best approach now available being a thermodynamic calculation of the deoxidizing power of boron in liquid steel by the general method used so successfully by Chipman1 in his study of the reactions in the open-hearth process. The thermal data for boron, upon which such a calculation must be based, are reasonably satisfactory; the only quantities not directly determined are the entropy of melting of boron, the activity coefficient of boron in liquid steel, and the activity coefficient of B203 in an open-hearth slag; but these values may be estimated with ample accuracy. The results of this calculation, which is presented later, are given in Table I, together with corresponding data for other deoxidizing elements. This table shows the calculated residual content of oxygen in equilibrium with different residual concentrations of the deoxidizer in the metal;

Jan 1, 1943

By C. K. Leith

THE purpose of these conferences has been to find some basic principles to guide us in the chaos which confronts us, to arrive at elements of a national policy. None such exists, nor, as a matter of fact, have there been any concerted efforts by the public or the mineral industry to evolve one. In the absence of such a policy the administrative agencies of the government can hardly be expected to be consistent or really effective in their handling of mineral problems, domestic or foreign. Basic Facts MINERAL reserves are unequally distributed among the nations. The principal world supplies are grouped around the north Atlantic, and nearly three-fourths of the world's total is controlled politically and commercially by English-speaking people. No one nation has a complete supply of the minerals necessary for modern industry; specialization, reciprocity, and large-scale movements between the nations are inherent in nature's unequal distribution of them. The principal sources of supply are relatively few compared with the nations to be served-a fact which determines broadly certain natural outlines of the world flow. National isolation with regard to minerals can be accomplished only through backward steps in industry and lower standards of living even in the nations possessing the most of the mineral supplies. A certain measure of unified commercial control, international in scope, is a natural consequence of the limited number of the large sources of supply. Mineral supplies for the world as a whole are so large that there is little need for concern about early exhaustion, but every nation has important problems of early exhaustion of particular minerals, which must affect their policies.

Jan 1, 1933

By John C. Gifford, Charles L. Thomas

A unique and reproducible method is presented for the determination of water vapor in tough pitch wire bar copper. The procedure involves reduction of the water vapor with molten aluminum to form hydrogen, which is subsequently measured by mass spectroscopy. Average water vapor pressures within the porosities of the wire bar samples are calculated. Correlation is to exist between the specific gravities of the samples and their measured water vapor contents. The method should find application as a very sensitive means of detecting hydrogen embrittlement in copper. The nature and quantity of gases evolved and retained during the horizontal casting of tough pitch wire bar copper have long been of interest to the metallurgist. Considerable work has been done at this laboratory on the determination of these gases. The work has involved not only qualitative but also quantitative analysis, so as to provide a basis for a total accounting of the porosity which is associated with the cast product. From a knowledge of the gas-forming elements within the copper, and the practice of melting and protecting it with a reducing flame followed by contact with a charcoal cover in the casting ladle, the gases which one might expect to find in the pores of the cast product are sulfur dioxide, carbon monoxide, carbon dioxide, hydrogen, and water vapor. Hydrogen sulfide, nitrogen, and hydrocarbons would be other possibilities; however vacuum fusion-mass spectroscopy techniques employed at this laboratory have shown that no hydrogen sulfide and only traces of nitrogen and methane are present. It is highly improbable according to phillipsl that any sulfur dioxide could be evolved in wire bar copper with 10 ppm or less sulfur under normal freezing conditions. Mackay and smith2 have noted that porosity due to sulfur dioxide only becomes noticeable at concentrations above 20 ppm S. Investigation of carbon monoxide and carbon dioxide by a variation in the method of Bever and Floe showed that these two gases could only account, at 760 mm and 1064°C (Cu-Cua eutectic temperature), for a maximum of about 25 pct of the total porosity in a wire bar having a specific gravity of 8.40 g per cu cm. phillips' has noted that no normal furnace atmosphere is ever sufficiently rich in hydrogen to cause porosity in copper from hydrogen alone. In addition, using a hot vacuum extraction technique for hydrogen,4 values have never been observed in excess of 10 ppb in tough pitch wire bar. On the basis of the preceding considerations of gases in tough pitch wire bar, only water vapor is left to account for the major portion of the porosity. Direct determinations of water vapor are virtually impossible at low concentrations by any presently known technique, due to adsorption and desorption within the walls of the apparatus used.5 The present investigation deals with a method for the determination of water vapor by an indirect procedure, using molten aluminum as a reducing agent to form hydrogen according to the reaction: 2A1 + 3H2O — A12O3 + 3H2 The evolved hydrogen can then be measured quantitatively by mass spectroscopy. EXPERIMENTAL A 10-g piece of 99.9+ pct A1 was charged into a porous alumina crucible (Laboratory Equipment Co., No. 528-30). Fig. 1 shows the crucible in place at the bottom of an 8-in.-long quartz thimble. A funnel tube with two l1/8-in.-OD sidearms extending at a 90-deg angle from each other was attached to the top of the thimble. One of the sidearms was joined to the inlet system of the mass spectrometer (Consolidated Electrodynamics Corp. Model 21-620A) via a mercury diffusion pump situated between two dry-ice traps. The copper samples were placed in the other sidearm, followed by a glass-enclosed magnetic stirring bar for pushing the samples into the crucible. All ground joints were sealed with vacuum-grade wax. The entire system was evacuated and the aluminum was heated with a T-2.5 Lepel High Frequency Induction Furnace for 21/2 hr at a temperature visually estimated to be 900°C. The temperature was then lowered and the hydrogen was monitored on the mass spectrometer until it was given off at a constant rate of about 4 to 5 1 per hr. This rate corresponded to a slope of 2 to 3 divisions per min on the X3 attenuation of a 10-mv recorder at a hydrogen sensitivity of approximately 100 divisions per 1. A micromanometer (Consolidated Electrodynamics Corp. Model 23-105)

Jan 1, 1969

By E. N. Doyle

Since the mid-1930's a number of plants, using the principles of heavy media separation, have been installed throughout the world. In cases involving lead, zinc or lead-zinc ores the reasons for the choice of this type of beneficiation process have fallen into four major categories: A) The economic recovery of additional distinctly separate products, such as dolomite limestone at the Mascot Plant (1) of the American Zinc Co., and the ferrosilicon produced by St. Joseph Lead Company. (2) B) The elimination of a large portion of run-of-the-mine ore prior to grinding and flotation, to allow increased throughput with low capital cost. Examples of this approach are the Levante and Ponente plants of the Montevecchio Company in Italy (3) and the frequent choice of the Sink-Float process by the Penarroya Company of Paris. C) The processing of a sedimentary deposit, in which the valuable mineral is contained in the matrix separating the boulders, as was the case at the St. Joseph Lead Company plant at Haydon Creek (4) and also at Bunker Hill Mining and Smelting, Kellogg, Idaho. D) The simplification of Around support programs in mines by allowing greater freedom of action in the extractive pattern. An example of this choice is Cominco’s Sullivan plant which came into being as part of an extensive proposal to update the mining, crushing, transportation, grinding and beneficiation processes. (5)

Jan 1, 1970

By S. Vela, R. M. McKinley, L. A. Carlton

Johnson et al. have described a new well-testing technique that measures formation flow properties between wells.' The technique, called pulse-testing, requires a sequence of rate changes in the flow at one well and measzcrement of the re.rulting pressure changes at an adjacent well with a very sensitive differential pressure gauge. This paper describes an extensive application of the technique in a producing oil field. Pulse-tests on 28 of 45 possible well pairs in the field provided a picture of the areal distribution of reservoir hydraulic diffusivity, trans-missibility and storage. The primary objective in presenting these data is to demonstrate the potential of the methcid for reservoir description. A second objective is to show in three ways the qualitative and quantitative accuracy of reservoir parameters determined from pulse-tests: (I) pulse-test data show a nonuniformity in the field, closely correlating with the oil-water distribution as given by production data: (2) pulse-test values for permeability are comparable with core va1ue.s; and (3) perhaps most important, the field responds to a conventional interference test in the manner in which pulse-test data predict it should. The pulse-testing technique by Johnson et al.' is an ideal source of data for purposes of reservoir description, for it provides a measurement of formation storage S = +ch, hydraulic diffusivity 91 = k/+cp and transmissibility T — This paper describes an application of this method in a producing oil field. Results were analyzed to give numerical values for the parameters 7, T and S. These values were compared with oil-water production data (for the effect of fluid saturation), with core data and with data from an interference test. The reservoir in which the pulse-test survey was run is the result of a structural trap formed by a fault along the east side of a north-south trending anticline. A down-structure aquifer providcs a natural flank water drive for the pool. The producing formation is a dolomitic lime- stone having mainly vugular permeability; the formation oil has a gravity of 29" API with negligible dissolved gas. The field contains 19 wells, all on pump, arranged on 40-acre spacing along the top of the anticline. Fig. 1 shows the location of all these wells except two at the south end of the field. The dashed line on the right-hand side of the figure represents the approximate location of the fault with respect to well positions. Pulse-Test Survey and Analysis of Data A pulse-test requires a pulsing well and a responding well. In the field, changes were made in the rate of flow at the pulsing well by stopping and starting the pump periodically and measuring the corresponding pressure

Jan 1, 1969

By Gordon A. Gross

Banded siliceous manganese-iron bearing sediments recognized as distinctive facies of Algoma-type iron formation constitute low-grade resources of manganese in many countries. Manganiferous facies associated with oxide and carbonate facies of iron formation have iron to manganese ratios ranging from 0.2 to 2 and commonly about one. Manganiferous facies up to 30 m thick occurring separately or with other iron formation facies are associated with cherts, carbonates, shales, turbidites, tuffs, and lavas. Primary cherty manganiferous facies and their gondite metamorphic equivalents represent significant manganese resources and are protores for higher-grade deposits derived by secondary enrichment processes.

Jan 1, 1983

By Pieter W. Greeff, Graeme W. Mitchell

INTRODUCTION This paper describes the underground environmental planning parameters developed for Pancontinental Mining Limited's Jabiluka uranium deposit. The deposit is located 230 km east of Darwin in the Alligator Rivers region of the Northern Territory, Australia. The deposit is situated within land subject to an Aboriginal land claim, adjacent to a National Park and within a proposed extension to that National Park, as well as being close to a long- established Aboriginal reserve. In addition, being the first large underground uranium mine planned in Australia, the environmental considerations, both on surface and underground are considerable. Pancontinental is committed to the highest practicable standard of environmental management in the operation of the mine. In addition, Government regulations and requirements are particularly stringent by world standards. The underground environmental problems are discussed later in the paper with emphasis placed upon radiation aspects, both gamma and radon daughters, and dust. Consideration has also been given to heat and humidity due to the location of the deposit in a sub-tropical region 12° south of the equator. The paper explains how these environmental factors influence the design and selection of stoping methods. GEOLOGY AND ORE RESERVES The Jabiluka Two orebody is completely overlain by flat-bedded Kombolgie Sandstone with a thin layer of surficial colluvial sands. The orebody occurs in an east-west striking folded succession of Lower Proterozoic metasedimentary rocks of the Cahill Formation. Uraninite and pitchblende constitute essentially all the uranium mineralisation and are contained in the four lithological series, as shown in Fig. 1. - ,Upper Graphite Series - Main Mine Series - Lower Mine Series 1 - Lower Mine Series 2 The succession at Jabiluka has been folded and forms an east-south-east striking, asymmetric syncline-anticline which dips south and plunges to the east. A major fault bisects Jabiluka Tw8 having a north-south trend and dipping about 80 to the west. A near vertical tourmaline granitic pegmatite dyke up to 30 m in thickness has intruded the Jabiluka Two orebody at the western end. Current drilled ore reserves for Jabiluka Two are 52.0 million tonnes at 0.39% U308. Included in these reserves are 1.1 million tonnes of gold ore at 10.7 g/tonne. A large proportion of the orebody can be mined in thick sections (over 80% of tonnage) either as single sections or by bulking a number of thin sections which are close together.

Jan 1, 1981

By K. L. Fetters, F. M. Walters

ALL previous records were broken by the Iron and Steel Division, in the number of sessions, the number of papers, and the attendance. In addition to ten papers (all preprinted) on properties, structure, aid hardenability of, carbon and alloy steels, eight formal papers were presented on one or more phases of steelmaklng, and a symposium on the determination of hydrogen and nitrogen in steel. This last started at 2 p.m. and was going strong with more than a third of the audience still present at 6 p.m.

Jan 1, 1944

By Robert W. Bruhn

An investigation was made of ground response to pillar retreat mining in a 1.7 meter thick seam at 108 meter depth at a site in northern West Virginia. This paper describes mining-related stress changes and movements at mine level, displacements within the overburden, ground surface subsidence and groundwater level variations. Subsidence approached 40 per cent of the mine height and continued more than a year after mining. Water levels declined in certain deep-lying strata.

Jan 1, 1984

By Charles Williams

BOYLE'S law states that the volume of a gas at B constant temperature varies inversely as its pressure, PV = C, or V = C/P Therefore, the volume of a gas at any pressure is to its corresponding pressure as the volume of the same gas at atmospheric pressure is to atmospheric pressure, V, = V° Also, P1 P0 the volume of the gas at any other pressure is to its corresponding pressure as the volume of the gas at atmospheric pressure is to atmospheric. pressure, V2/P1 V0/P0 V°P VA Solving for V1 and V2, V2 = and V2 =V0P2/P0

Jan 2, 1927

By Robert E. Green, Kenneth Reifsnider

Several experiments have been performed in order to illustrate the application of a recently developed X-ray image intensifier system to metallurgical investigations. In the present work the system has been used to study the instantaneous alterations in Laue transmission X-ray diffraction patterns during tensile deformation of aluminum single crystals. Expem'mental results are presented which demonstrate the capability of the system for crystal orientation, for following orientation changes due to lattice rotation during tensile deformation, and for showing changes in the homogeneity of the lattice planes along the specimen length as a function of strain rate. RECENTLY, a new X-ray system has been developed which incorporates a cascaded image intensifier and permits direct viewing and recording of X-ray diffraction patterns produced on a fluorescent screen.1"3 In the present work the results of several experiments are presented which demonstrate the usefulness of this system for metallurgical applications. EXPERIMENTAL PROCEDURE A schematic diagram of the experimental arrangement is shown in Fig. 1. In this system a Machlett AEG-50-S tungsten target X-ray tube, normally operated at 50 kv and 40 ma, serves as the X-ray source. The X-ray tube is placed in direct contact with a 10-in.-long collimator, which transforms the X-ray beam from one with a circular cross section to one with a rectangular cross section 3 in. high and 1/6in. wide. By blocking off all but a small portion of the rectangular slit, it is possible to work with the more conventional "pinhole" collimated X-ray beam commonly used for obtaining Laue diffraction patterns. In the present work the test specimens were 99.99+ pct aluminum single crystal wires & in. in diam and 3 in. long. For the deformation tests the wire crystals were mounted in a special set of grips in a table model Instron machine so that diffraction patterns could be recorded during specimen deformation. For the orientation tests the wire crystals were mounted in a rotating goniometer so that diffraction patterns could be recorded during specimen rotation. At a distance of 3 cm from the specimen axis, a 6 in. diam DuPont CB-2 fluorescent screen is positioned to transform the X-ray image to a visible one. A Super Farron f/0.87 72 mm coupling lens, corrected for 4 to 1 demagnification, transmits the visible image to the image tube. The image intensifier used is a three-stage magnetically focused RCA type C70021A with an S-20 input photocathode and a P-20 output phosphor. The tube has unity magnification and useful input and output screen diameters of 1.5 in. The image on the output phosphor is of sufficient intensity to be viewed directly, to be recorded cine-matographically, or to be displayed by vidicon pick-up on a television monitor. The recording device most commonly used is a 16 mm Bolex motion picture camera fitted with a Canon f/0.95, 50 mm lens. The overall gain of the system is 16,000 for direct viewing and 2240 for recording on 16 mm movie film. The resolution of the system is limited to 1 line pair per mm which is approximately that of the fluorescent screen. This system has been used for cine recording of transmission Laue X-ray diffraction patterns with exposure times as short as 1/220 sec and for vidicon television pick-up and display at a scan time of 1/30 sec. Quantitative information may be obtained from each frame of the movie film, by either stopping the vertical slit down to a point source in order to obtain a conventional Laue photograph or else by retaining the linear beam and introducing fiducial marks as described in a previous paper.4 In either case, each frame may be enlarged to appropriate size for analysis by either using a photographic enlarger and making prints of the desired frames, or, more conveniently, by using a microfilm reader. EXPERIMENTAL RESULTS The first series of photographs which are presented in Fig. 2 serves to demonstrate the usefulness of the system for crystallographic orientation determination. This series of prints, made from enlargements of a 16 mm movie film, shows the dynamic Laue transmission patterns produced by an aluminum single crystal wire which was rotating about the wire axis when the patterns were recorded. The movie films were taken at 16 frames per sec and the crystal was rotated at a rate of 15 rpm.

Jan 1, 1970

By O. Skiredj, J. F. Elliott

It has been necessary to collate the available data on the solubility of graphite in Fe-Si-Mn alloys for a study of slag-metal equilibria in ferromanganese production. That study will be reported later; the collation is reported here. The carbon content of graphite-saturated liquid iron above 1153ºC by Chipman and co-workers1 is: %C= 1.34 + 2.54 x 10~3t(°C) [l] For graphite-saturated manganese above 1322ºC it is: %C = 2.68 + 3.52 x 1CT3 t(°C) [2]

Jan 1, 1963