Search Documents

By S. W. Ross

In 1936 a description of the plant (Fig 1) and process employed by the Electrolytic Zinc Co. of Australasia Ltd. for the recovery of zinc from zinc concentrate by the electrolytic process was prepared. † During the twelve years which have elapsed since the preparation of the earlier paper, several major changes in the metallurgy of the process have been introduced. It is the purpose of the present paper to give a general description of these changes and thus to bring up to date the description of the plant and process. Summary The major changes in Risdon practice since 1936 have been: 1. Replacement of two stage roasting by a preliminary roast followed by the flotation of all the leach residue and the roasting of the flotation concentrate. 2. Screening of all calcine fed to the pachucas. 3. Continuous leaching of calcine and improved classification of pachuca discharge. 4. Close control of hydrogen ion concentration during purification for iron removal. 5. Recovery of cobalt as a good grade oxide. 6. Production of part of the zinc output in the form of "four nines" metal (99.99 pct purity). 7. Closer spacing of electrodes thus increasing the potential output of cathode zinc per cell by 50 pct. Changes which are in prospect and for which construction work is proceeding at the present time involve the starting up of: 1. Two suspension roasters. 2. A contact acid plant to produce 150 tons‡ of acid per day and replacing the existing Mills Packard chamber plant. 3. Extra power station capacity to permit greater current flow to existing cell room units. This will increase the output of cathode zinc from about 245 to 290 tons per day. Plans for the future envisage the building of an ammonium sulphate plant, the first unit of which will produce about 50,000 tons per year, and improved treatment of zinc plant residue for the recovery of zinc, lead and other metals. At the end of this paper tables of metallurgical data are presented relating to the year ending June 30, 1948. Details of Changed Practice Output In 1936 the production of cathode zinc amounted to about 200 tons per day. This has since been increased to about 245 tons per day while plant extensions are practically complete which will permit of an output of about 290 tons per day in the near future. Roasting Division ROASTING POLICY A major change has occurred in the roasting policy. Twelve years ago the method in use was to carry out a two stage roast in the first stage of which sulphide sulphur was reduced to about 6 pct. The pre-roast calcine was re-roasted in modified Leggo furnaces using coal as fuel, sulphide sulphur being reduced to about 0.8 pct. The whole procedure was described on pp. 482491 of the earlier paper. Although this roasting procedure had certain advantages it possessed some distinct disadvantages. For instance, it appeared uneconomical to heat up the entire input of pre-roast calcine to roasting temperature by the expenditure of fuel in order to oxidise a few percent of sulphide sulphur. It was argued that if the pre-roast calcine were leached and a process could be developed for the recovery of a zinc sulphide concentrate from the leach residue, this concentrate, small in weight compared with the pre-roost calcine, would probably roast autogenously, thus virtually eliminating the expenditure of fuel as well as greatly increasing the weight of sulphur oxidised per square foot of furnace hearth area. The obvious method of producing a suitable concentrate from leach residue was by flotation. It will be recalled (see p. 495 of the earlier paper) that when two-stage roasting was practised the leach residue was classified, the granular fraction was ground and floated while the slime fraction was thickened, filtered and dried ready for shipment to a lead smelter. This process worked quite successfully. However, when trials were made of leaching a calcine carrying several percent of sulphide sulphur the granular fraction still floated well, but the slime fraction carrying 8-10 pct sulphide sulphur yielded very poor results when subjected to flotation. This fact held up the application of "pre-roast" leaching for many years. However, successful flotation of the slime fraction of leach residue was finally achieved and in August 1940 the slime flotation plant began operation, while the leach-

Jan 1, 1950

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Harmel A. Dawson, Robert A. Wilson

First the basic steps to determine the values present and the minerals involved which are the basis for the metallurgical testing are presented in this paper. Next, choosing the process or processes indicated for treating an ore are discussed. This is followed by the test procedures used, the results of which will indicate amenability to treatment. These test procedures have been developed, used and proven effective in laboratory evaluations relative to plant processing. Special, uncommon processing is beyond the scope of the paper. Evalutation of test results and incorporation into the preliminary and final flow sheet for plant design are discussed. The value of a flow sheet, with material and water balances, to plant design is shown.

Jan 1, 1978

By Clinton M. Young

The experiments herein described were carried on in 1908-9 by- the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coalmines, a subject which is engaging the attention of numerous investigators. An unusual number of serious disasters has directed to the subject a study which discloses the disquieting fact that, in the United States, the ratio of lives lost per ton of coal mined has been 011 the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and a very great increase in the amount of explosive used. This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle West it is not now uncommon for a miner to use six kegs (150 lb.) of black powder in a " pay" of two weeks, while within the memory of men still active, one keg (25 Ib.) would last two men for a " pay." So great has the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject of explosions in coalmines has led to the belief that the use of large quantities of explosives, in some cases by slightly-trained men, had riot been

Jan 1, 1911

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965

By R. W. Raymond

THE absence of a convenient glossary of terns connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale's work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copp, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction ; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place' individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who hays favored me with ' assistance and advice. The labor bestowed upon this paper since its presentation, at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By Yap Chu-Phay

IN the previous paper, the writer showed how, on the basis of thermodynamic reasoning, it seems probable that when true equilibrium conditions obtain, carbon exists as Fe3C in the liquid state and as elementary carbon in the solid state (7 Fe), in which case the solidus would be a straight line from 0.18 to 1.70 per cent. carbon (Fig. 1). In the same paper he concluded that the solidus obtained by Honda 'and his co-workers1 probably does not represent the same conditions, insuring a complete equilibrium. Except for a downward temperature displacement, the solidus obtained by Gutowsky,2 using the Heycock and Neville method, practically coincides with Honda's solidus as shown in Fig. 1. The writer at first thought that perhaps in some way Gutowsky's thermocouple was improperly calibrated for high-temperature measurements, as his liquidus was also much lower than those obtained by Carpenter and Keeling3 and by Ruer and Goerens.4 However, the eutectic temperature obtained by Gutowsky agrees with the generally accepted value of 1130° C., so that the validity of the inference regarding improper temperature calibrations is to be strongly doubted. In Fig. 1, Gutowsky's solidus is shown both in the original and in the corrected form. In the latter, a correction of 29.2° C. is made for all temperatures above 1416° C. in accordance with-

Jan 1, 1931

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid iron alloys containing chromium and nickel has been measured in the temperature range 1550° to 1700°C at nitrogen pressures to 1 ah. The solubility surface has been determined for the iron corner of the liquid metallic ternary to 21 pct Cr and 11 pct Ni. The nitrogen solubility increases markedly with increasing chromium concentration. The effect of nickel and the bilinear effect of chromium and nickel are less pronounced. The solubility data are presented, and interaction coefficients are determined from them. THE solubility of nitrogen has been determined in liquid Fe-Cr-Ni binary and ternary alloys. The work in this laboratory has been directed toward a relatively limited composition range, that is to 20 pct Cr and 10 pct Ni. Humbert and Elliott1 studied the entire ternary; but their investigation was, understandably, limited in this region. The region considered here is of the greatest commercial interest. Knowledge of the solubility in these alloys is important for accurate control of the nitrogen levels in various stainless alloys. Also, the solution behavior is of theoretical interest because of its deviations from ideal dilute solution rules at moderate chromium levels. The nitrogen solubility in the iron binaries has been reviewed extensively by Pehlke and Elliott,2 particularly with respect to the dilute solution interaction parameters. More recently, there has been some interest in accurate descriptions of solute interactions in non-dilute solutions. Most of the investigators have adopted a power series fit to accommodate any non-linearity of the data. The Taylor series expansion is adopted here, using Scimar's notation3 for the interaction coefficients. An alternate method, instead of requiring higher-order expansions, is to restrict the range of the composition variables. A planar solubility surface may be fitted to the data and its range of validity determined. If the axes of this region are displaced from the usual origin—the solvent pure iron—a change in standard state is required for the solution reaction. The standard state for nitrogen in iron is commonly taken as the hypothetical 1 wt pct solution of nitrogen in pure iron. However, for an alloy of appreciable solute concentration, e.g., 13 pct Cr or 18 pct Cr-8 pct Ni, it would be convenient to use that base composition as the solvent and redefine the solution reaction in terms of that particular solvent. A brief derivation follows, defining the free energy of solution in an alloy solvent. Following the treatment by Darken and Gurry,4 for a nitrogen pressure of 1 atm: N (pure component) = N (1 wt pct in solvent) [l] AG=RT ln100/ wt pct N in solvent Taking this reaction for an alloy solvent less the same reaction for a pure iron solvent the relation between nitrogen in pure iron and an alloy is: N (1 wt pct in Fe) = N (1 wt pct in alloy) [2] AG = RT[ln(wt pct N in Fe) - ln(wt pct N in alloy)] Adding ½ N2(g) to each side and subtracting N (1 wt pct in Fe) = ½N2(g), the total free energy for solution of nitrogen in an alloy, referred to nitrogen at infinite dilution, is given by: ½N2 (g) = N (wt pct in alloy) L3] AG°3 = -RT ln(wt pct N in alloy )PN =1 atm Interaction parameters have their usual meaning when ?G°/RT is differentiated with respect to the proper composition coordinate. If desired, the dilute alloy treatment may be utilized with the new reference composition as the solvent. This has. indeed, been done by Small and pehlke5 in their analysis of nitrogen solution in liquid 18-8 alloys. The Sieverts' technique was used for this investigation on an apparatus previously described.6 The materials used in this program were: Ferrovac-E iron, 99.95 pct, Crucible Steel Co.: chromium, 99.95 pct, Union Carbide Metals Co.; nickel, 99.9 pct, International Nickel Co. Recrystallized alumina crucibles were used with no evidence of crucible-melt reaction. RESULTS The locations of the ternary compositions investigated are shown in Fig. 1. The data of Turnock7 and small8 have been alluded to in other papers.5'6 There were no departures from Sieverts' law observed for

Jan 1, 1969

By Barrie T. Wells, Raghu N. Singh, Paul S. Buddery

Rockbolting and dowelling are important methods of ground control. Their effectiveness depends upon the compatibility of the support members and the geotechnical behaviour of the rock mass. Detailed geotechnical investigations are, therefore, necessary for the design of effective rockbolting systems. The study described in the paper was concerned with improving the effectiveness of ground control at Mount Isa Mine. The paper briefly reviews the design methods avail- able when choosing a rockbolting system with a view to identifying the most suitable method. Joint surveys were used for the geotechnical assessment of rock mass stability. These were interpreted with the aid of the stereographic technique of predicting the size and shape of potentially unstable blocks of rock in both the roof and side walls of excavations. The geology and ground conditions at Mount Isa are briefly described together with the current ground control techniques. The requirements for ground control have been investigated at representative sites by analysing typical modes of rock failure and using a geological predictive technique. An application of this technique to the selection of a support system in a shallow Coal Measures tunnel is also described. The paper concludes with a general discussion on the effectiveness of this method of site investigation for the appraisal of rockbolting support in mining and civil engineering excavations.

Jan 1, 1983

By A. B., Sabin

THERE are many who know The Lucky Tiger and will remember the 35-mile road from Esqueda, a station on The Nacozari Railroad in northern Sonora, Mexico. They will remember the box canyons of the Agua Caliente Mountains which are scarcely wide enough for two cars to pass; the Bavispe River which one hour may be a lazy trickle and the next a sweeping torrent, and the tortuous road up Tigre and Espuela canyons, now following the wash, now hugging some gigantic red cliff. It is still the same. From camp the view of the distant blue-gray mountains is the same. But one thing a visitor of a former day might miss: The hundreds of pack mules and burros, loaded with concentrates from the mill, which used to take most of the road and show up at the most inopportune places, have almost disappeared, replaced of course by the auto truck.

Jan 1, 1929

No phase of the steel industry is more typical of its remark- able progress than is the evolution and development of the modern American blast furnace. The founding of the Institute in 1871 also marked the beginning of a new era in the pig-iron industry. The rapidly expanding westward development of the country, with its seemingly unlimited markets, gave rise to unprecedented demands for blast-furnace products. The manner in which the iron industry responded provides a fascinating chapter in the history of industrial development. Prior to this period, the iron industry of the United States, largely concentrated in the East, was based upon the consumption of local iron ores and local fuels, the latter predominately charcoal and anthracite. Small, isolated furnaces were located near scattered ore and fuel sources, and the completely integrated ironworks and steelworks were yet to be developed. In about 1860 exploitation of the newly discovered rich ore deposits in Michigan and the successful adaptation of blast furnaces to coke produced from coal of the great Pittsburgh seam in western Pennsylvania proved to be major factors in firmly establishing the general westward shift of the industry. But these were largely economic in character, and it was not until about 1870 that the aggressive, individualistic nature of the ironmaster asserted itself in no uncertain manner. No longer limited by relatively inadequate equipment and inferior raw materials, and spurred as well as encouraged by those who supplied capital for these new enterprises, furnacemen began to establish unheard of records in iron production. It is not surprising that Pittsburgh was the center of this new activity. Its tenor is best indicated by the following account :l

Jan 1, 1948

By Frank Corwin

It is the purpose of this article to give a brief account. of the experimental work and to show how the increase in efficiency was brought about. Part of the experimental work described in this paper was carried out by the writers, while in the employ of the Anaconda Copper Mining Co., under the direction of M. W. Krejci, Metallurgist, and Arthur Crowfoot, Chief Sampler. Complete records of all of the MacDougall testing work have been placed at our disposal through the courtesy of A. E. Wheeler, Superintendent. II. BRIEF HISTORY OF PRESENT MACDOUGALL PLANT. The first change from the Brueckner cylinders used for roasting concentrates at Great Falls was the construction of a MacDougall roaster of the Herreshoff type. This furnace was first started on June 15, 1898. It bad eight hearths, was lined with fire brick, and had an air-cooled central shaft, but no provision was made for cooling the rabble arms. It was operated for a while, and accomplished the work of roasting, but ran so hot that the rabble arms became twisted and distorted out of shape. To prevent the furnace from becoming too hot a device was then installed to draw the heated gases away from the hearths. This consisted of a pipe connected to alternate hearths of the MacDougall furnace and also connected to the flue. It was equipped with dampers, 'so that the hot gases could be drawn away from any one of the alternate hearths directly into the flue.

Jan 7, 1913

By K. A. Svanstrom, W. R. Opie

Problems associated with deposition of titanium infused chloride baths using TiCl4 as a feed material are reviewed. A potentially workable cell design using Alumdum diaphragms is discussed. Problems inherent to diaphragm-type cells are emphasized and experiments described which led to the development of a cell without a diaphragm. INVESTIGATORS assigned the problem of developing a commercial electrolytic process for making titanium metal have found that they are faced with the difficulty of overtaking rapidly improving magnesium and -sodium reduction processes. The ultimate goal must be a simple process that can be conducted with low-cost raw materials in equipment that is inexpensive to build and operate. This paper deals with some work of a preliminary nature conducted by personnel of the Research Laboratories, National Lead Co., Titanium Division. Many others have reported on the general subject of depositing titanium from fused salt electrolytes. A partial bibliography is attached. PRIMARY CONCEPTS Anyone attempting to deposit titanium metal from fused chloride electrolytes using TiC14 as a source material is faced with at least the following problems: 1) Getting the titanium into solution in the bath. 2) Controlling oxidation and reduction reactions associated with multiple valency of titanium, which result in low electrical efficiency. a) Prevention of dichloride oxidizing to trichloride and trichloride to tetrachloride at the anode. b) Prevention of trichloride from being reduced only to dichloride at the cathode. 3) Prevention of metal formation away from the cathode thru disproportionation of titanium dichloride to satisfy the equilibrium. 3 TiCl2 == 2 TiCl3 Ti [I] 4) Protection of reduced chlorides in the bath from reaction with oxygen from the bath container or air. 5) Removing from the bath the deposited metal formed without allowing it to become contaminated with oxygen or nitrogen. 6) Selecting cell materials of construction which will not contaminate the metal product or cause cell inefficiencies. EARLY EXPERIMENTS The initial attempts made to electrodeposit titanium from fused chloride baths using TiCl4 as a source material indicated that TiCl4 was essentially insoluble in molten chlorides of alkali and alkaline earth metals. If, however, the TiCl4 was introduced close to a nickel cathode some metal could be formed and appreciable quantities of reduced chlorides would be present. These reduced chlorides reacted with any oxygen present in the atmosphere above the bath and would also diffuse quickly to the anode (graphite) where they would react with chlorine and be evolved as TiCl4. The net electrolytic efficiency of such a cell is essentially nil. The TiCl4 evolves from the anode at almost the same rate that it is introduced in the vicinity of the cathode although a small amount of titanium metal can be formed on the walls of the cathodic pipe. It becomes apparent from the operation of such a cell that: metal can be deposited on the cathode, although of small particle size and a nonadherent nature, and when reduced chlorides are present in the electrolyte, TiCl4 can be absorbed, probably by the following reactions: TiCl4 + TiC12 - 2 TiCl3 [21 2 TiCl3 + 2 faradays - 2 TiC12 + C12 [31 DIAPHRAGM CELLS These facts encouraged the development of cells containing diaphragms to prevent migration of reduced chlorides from the cathode area to the anode. Small-scale cells for process development are described by Alpert, Schultz, and Sullivan.20 A larger brick-lined cell incorporating internal heating by passing ac through the bath is shown in

Jan 1, 1960

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,' magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,' magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By Walter Kauzmann

ALL viscous or plastic flow of incompressible matter is the result of shear strain; the changing shape of any body that is being plastically deformed can be completely described in terms of the shear strain occurring at each point in the body.[t] Furthermore, the relative amounts of shear strain occurring in different parts of a body under stress depend upon the relative rates of shear strain at those different points, so that if the dependence of the shear rate of any material on the temperature, shear stress, previous history, etc., were understood, the principles of plastic deformation would be known, and we could calculate how a body made of a given material, having a given shape, and subject to a specified system of forces, would change its shape with time. It may be said, then, that the problem of plasticity resolves itself into, first, the problem of the rates of pure shear processes, and second, the application of what is known about pure shear to actual cases. It is the purpose of this work to investigate the former problem -i.e., the dependence of shear rates on temperature, stress, etc.-from the standpoint of recent developments in the field of chemical-rate theory and with particular reference to the phenomena occurring in the creep of metals and in the plastic flow of crystalline solids in general. It is left for the mechanical engineer, and perhaps the expert in hydrodynamics, to deal with the problem of applications1 RESOLUTION OF MACROSCOPIC SHEAR INTO MICROSCOPIC MOVEMENTS; RESEMBLANCE TO CHEMICAL REACTIONS Just as any large body is made up of many small units, or atoms, so macroscopically observable shear is the result of many microscopic unit shear processes; just as the understanding of the behavior of large bodies demands the understanding of the atoms of which it is made, so the understanding of macroscopic shear demands the understanding of these fundamental unit processes. The study of shear from this "atomistic" point of view has made considerable progress. There has been fairly complete understanding of shear processes in gases for a long time, at least for nonturbulent flow, as a chapter on gaseous viscosity in any text on the kinetic theory of gases will prove. In recent years Andrade2 and Eyring3 have presented important theories for the flow of liquids and amorphous solids. Becker,4 Orowan,5 Taylor,6 Burgers,7 and Kanter8 have considered the

Jan 1, 1941

By E. S. Rowland, J. Welchner, R. H Marshall

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944

By R. H. Marshall, J. Welchner, E. S. Rowland

This paper presents results on an extension into the realm of high-carbon steels of some work recently published1 on the effects of time at temperature, quenching temperature and prior structure on the hardenability of one 0.20 and four 0.40 per cent carbon alloy steels. It was shown at that time that unless the conditions of time, temperature and prior structure are substantially the same in performing the hardenability test as in conducting hardening of parts in production, the correlation of hardenability information with the hardness and properties of production parts is often not of satisfactory accuracy. The general effects of these variables on the austenitic grain size, distribution of excess carbides and critical cooling rate have been known for many years and one or more have been investigated by Shepherd,2,3 Davenport and Bain,4 Digges,5,6 Digges and Jordan,' Post and associates8 and Roberts and Mehl,9 to mention only a few. There has been no systematic investigation, however, into the quantitative variations produced on the hardenability of commercial high-carbon steels by changes in these factors of time, temperature and prior structure. Procedure A plain carbon hypereutectoid steel, S.A.E. 52100 and Graph-Mo, a molybdenum-bearing high-carbon steel containing some graphite, were chosen for this investigation. The chemical analyses of these electric-furnace steels are given in Table I. The procedure used was exactly that reported previously,' hence the details will not be repeated here. Normalized (165o°F.) and spheroidized prior structures were utilized on all steels with hot-rolled and quenched (I600°F. oil) prior conditions added for the plain carbon steel. The end-quench test developed by Jominy10 was sclected for use in this investigation and, with the noted exceptions, the American Society for Testing Materials standard procedure was followed. The effect of time at temperature was examined at intervals of o, 10 and 40 min. and 4 hr., and a few 16-hr. tests were run. Salt-bath heating of the specimens was employed to control and minimize the

Jan 1, 1944