Search Documents

By Charles Hart

THE-report of the advisory committee to the U. S. Bureau of Mines, on the use of oxygen in metallurgy, brings to the art of steelmaking a radical change in the method of operation of the many processes of this widely diversified industry. When completed, the improvements suggested by the use of oxygen will be far-reaching and revolutionary. As to its effect upon the iron blast furnace, the use of oxygen should be as important as any of the improvements in the art of iron smelting and should take its place beside the German "Hochofen" which was the first attempt to use a shaft for preheating the stock, and beside the hot-blast stove which heated the blast before entering the furnace. The former initially produced molten iron and the latter made unbelievable economies in fuel consumption. It would seem that a discussion of this paper would be best served by following the conclusions on page 17 of the report and analyzing them seriatim. 1. (a) A decrease in costs, due to higher smelting heats is only attainable by taking full advantage of these heat units. This is affected by, adding additional ore to the burden which in turn increases production and yields a larger tonnage upon which to figure costs. These economies appear in decreased cost per ton of iron for coke and limestone consumed, and a proportionate reduction in all items entering the cost above materials. We can take no exception to these. premises. It is a well-known fact that silicon in the iron and sulfur removed" are the result of hearth temperature, other matters remaining constant. To a practical furnaceman the most satisfactory manner of controlling a furnace is by increasing the burden. It is not necessary, therefore, to consider the question of refractories, for this discussion presupposes that the temperatures in the furnaces will be kept practically where they now stand for making the various grades of iron. The same situation obtains in regard to the height of the furnace, which, as intimated, was one of the great strides forward in this art, and its abandonment at this time, is inconceivable. The shaft prepares the stock so that at each succeeding step we have exactly the proper conditions. All the stock entering the furnace is dried and preheated. The limestone is calcined by sensible heat practically at no cost, for this is sensible heat which otherwise would pass from the top with the gases. Under normal conditions, external calcination has been attempted without tangible results. Under normal average furnace operation, limestone requires about 760 B.t.u. for calcination and the loss of sensible

Jan 11, 1924

By Tony B. Szwilski, K. Unrug

INTRODUCTION Since the introduction of longwall coal mining systems, reliable predictions of roof support requirements at the face and the roof caveability in the gob area have been major contributors to the success of the longwall face by means of safety and face productivity. That is, the successful operation of a longwall is well-served by good regular caving of the gob. In recent times, with the advent of increased coal face mechanization and capital investment, the evaluation of the feasibility of longwall mining has become essential. In the United States, where a face unit for a face length of about 150 metres may cost around $6 million, a quantitative system that would assist in selecting the best equipment for the coal would prove extremely beneficial. There have been many such varied investigations in the past few years. A vast -amount of work has been invested principally by West Germany [3, 7, 8, 91 , Poland [I, 101 , United Kingdom [4, 5, lo], France [4], and South Africa [4]. It is the object of this paper to review this previous research work and give an outline that may be used as guidelines for long- wall evaluation. Essentially, for the initial design phase for a longwall system, account must be taken of the geometry of the coal panel, its position relative to the surface (depth), direction of the coal cleat system, faults and in-situ stresses and other neighboring workings in the same coal seam and other seams both above and below. The advance of the coal panel disturbs the stress field and in doing so creates an abutment zone around the face. At this stage the condition of homogeneity of the surrounding rock mass does not apply. The magnitude of the rock strata pressure may exceed the ultimate strength of the rocks and create zones of clastic, plastic and elastic material, the limits of which are difficult to determine. The collapse of the gob and resulting expansion of the displaced waste roof rock, create a statically undefined support complicating an already unclear rock structure. For example, it is often a point of debate whether, indeed, the vertical strata pressure develops to regain the original magnitude of virgin stress. Under these post-failure circumstances an analytical approach based on simplified and idealized assumptions can only be considered a very general approximation. Theoretical concepts, however, may be adequately supplemented by empirical methods that are based on numerous underground observations and surveys [3, 4, 7, 8]. These methods employ the use of rock indices that very handily correspond to the competence of the roof rock mass. Scale model work [3, 41 , using equivalent materials representing the surrounding rock mass within the coal seam zone, have given valuable qualitative and sometimes quantitative data in addressing the behaviour of the rock mass around longwall panels. To characterize the state of art of caveability predictioqthe principal concepts will be reviewed with special emphasis placed on practicality for the planning of longwall operation. It has been the general observation of the authors that many of the literature surveys published in English often neglect reference to other international mining literature. It is with this point in mind that an overall review has been written including mining concepts identified with the principal coal mining countries. THEORETICAL CONCEPTS Arching Theory For the development of this theory, assumption has been made that an extracted height, h, in a coal seam results in an extracted panel of width, w . Also, the coal seam is horizontal and the rock strata of both the roof and floor are homogeneous. The primary (virgin) stress distribution will change in the roof as well as the floor. As a result of lack of support caused by the excavation (in the gob area) an additional load is developed due to the redistribution of the load around the sides of the panel, referred to as the abutment, R, where: [ ]

Jan 1, 1982

Mills Day left a journal of his travel to Ohio and return by way of Pittsburgh in 1810. He left this comment about western Pennsylvania: "June 19. As I proceeded toward Pittsburg, (From Washington and Canonsburg) the country grew more populous. The hills appeared to consist of strata of freestone, iron, coal, and slate. June 20. Its (Pittsburg's) water communication with a vast extent of country and the immense beds of coal in its immediate vicinity render it a place peculiarly adapted to manufactures. Coal may be obtained of a good quality, ready delivered at 5 cents a bushel."1 Until within a year or so of this period, coal was used for domestic purposes, brick-making, by blacksmiths, etc.; now the industry entered a period of rapid growth caused by the introduction of the steam engine. As manufacturing was increasing due to the settlement of the western country, the additional facilities created by mechanical power were welcome. Apparently the first engine was installed in Pittsburgh, in a steam grist mill, in 1808; it is described in the Navigator of 1811: "The water of the boilers are heated by large fires made of stone coal, which is introduced at one end into a grated fire place as long as the cylinders themselves; the quantity of coal consumed daily by these boilers is said to be about twenty bushels, which cost one dollar." Later it mentions the effect of burning coal:

Jan 1, 1942

By E. V. Potter, E. T. Hayes, H. C. Lukens

Large volumes of hydrogen are liberated at the cathode during electrolytic precipitation of manganese. Most of the gas escapes from the electrolyte, but a considerable amount may be entrapped in the manganese plate. Gas has been observed to escape from manganese melts in puffs that bite at the surface. It has been reported that castings made with electrolytic manganese tend to rise in the molds; for this reason the manganese is often treated to remove hydrogen before the melt is made or it is premelted and used as cast manganese in making the alloys. The effect of hydrogen on the properties of manganese and its alloys is not known, but its effect on iron and iron alloys has been studied extensively.l.2 The close relationship between iron and manganese suggests that hydrogen may have a similar effect on the properties of manganese and its alloys. The purpose of this investigation was to determine the amount of hydrogen or other gases in typical commercial electrolytic manganese sheet and to investigate ways of removing it most conveniently. Apparatus The apparatus used is shown schematically in Fig. I. It consists of a chamber A in which the metal sample is placed, a vacuum or pressure gauge B, volume gauge C, vacuum pump D, hydrogen container E, auxiliary gas chamber F, and furnace G. The specimen chamber was made of two concentric quartz tubes. The outer one, a, connects with the closed gas system and is surrounded by the furnace G. A second tube, b, fits closely inside a and has a small end that projects into the space for the specimen and holds the thermocouple for measuring the temperature of the sample. The inner tube is joined to the outer tube outside the furnace, with rubber tape and sealing wax, to prevent gas leakage into or out of the closed system. This type of specimen container is loaded very easily and can be used several times if molten metal does not come in contact with the quartz. An ordinary mercury manometer B is used to measure the pressure in the system. The volume gauge C is essentially another mercury manometer, but the volume of the column is much larger than normal and the height of the mercury can be varied by raising or lowering the well H. In this apparatus the tube had a volume of IOO C.C. for a 60-cm. length. For larger changes in gas volumes, auxiliary containers F were used to increase the volume of the system by known amounts. Valves were arranged so that these auxiliary containers could be filled from the system and evacuated by the pump as often as necessary to accommodate the increases in the volume of gas in the system. The furnace G, used to heat the samples, was equipped with an automatic temperature controller, which maintained the desired temperatures within ± 5°C.

Jan 1, 1945

By AIME AIME

REPUBLIC STEEL'S new iron blast furnace in Alabama, shown on the cover of this issue, is the first to be completed of those authorized by the Government last year when a shortage of scrap became acute. In addition to the furnace, the new equipment includes a new battery of by-product coke ovens, a boiler plant, a generating unit, a 3-mile-long 60-in. water line, a huge gas washer, and precipitators in which the dust from the furnace is washed, separated from the water, and fed back into the furnace as raw material. The new unit is a cylindrical steel giant reaching 130 ft. into the air above the ground level. Because of the high humidity in the deep South, the furnace has been air-conditioned to avoid blowing eighteen tons of water into the furnace daily. Designed by Republic engineers who also had charge of the actual construction, the new furnace incorporates the best in modern blastfurnace practice. Orders to proceed with the construction of the furnace were received Sept. 22, 1941. The engineering crew, which was immediately organized, made more than 1500 drawings. Excavation started the next day, and simultaneously work was begun on demolishing existing buildings and preparing the site. The first concrete was poured Oct. 7 and the first piece of steel swung into place by a giant derrick on Jan. 30, 1942. It began operating May 28. A total of 70,000 cu. yd. of earth was moved and 30,000 cu. yd. of concrete poured.

Jan 1, 1942

By D. L. Blakeman, Trimble. J. W., S. W. Banning

Noranda's Grey Eagle mine and mill, in the Siskiyou Mountains of northern California, began shakedown operations in the late fall and early winter of 1982. This paper describes some of the unique features in mineralogy, milling, and water treatment operation at Grey Eagle. In addition, major start-up problems in the mill and water treatment plant are discussed along with measures taken to correct these problems.

Jan 1, 1986

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Otis W. Freeman

Production of oil in Indiana during 1944 is estimated at approximately 4,950,000 bbl., a decline of 6 per cent from the preceding year. Shortage of labor and material, together with governmental regulations resulting from the war, largely account for the drop in output and limited new developments. Three new pools were discovered in the state during 1944. Two of these, New Harmony, South, and Hovey, West, are in Posey County. Six wells in the New Harmony, South, field produced 66,422 bbl. of oil last year. A third field, Cato, in Pike County, did not market the oil from its discovery well during 1944. Several wells discovered oil in the Henderson field of Jay County along the Ohio state line. An important south extension of the St. Thomas field in Knox County was discovered during the year. Active drilling took place in the Inman, East, and Upton fields, Posey County, both discovered in 1943. Twenty-two wells in Inman, East, produced 151,1gr bbl. in 1944 and 12 in Upton produced 107,052 bbl. Owensville, and especially Owensville, North, in Gibson County, made large gains in production as a result of active drilling. The Dodds Bridge field in Sullivan County continued good production from deep sands reached in 1942. The Griffin continued to be the largest producer among the oil pools of Indiana, accounting for 2,004,180 bbl., over 40 per cent of the state's output. The next largest producing fields are Mt. Vernon and New Harmony, both in Posey County. The largest gas well brought in during 1944 was in the Rockport field, Spencer County, and had an initial output of 2,680,000 cu. ft. per day. The most productive gas fields in Indiana are Rockport, Spencer County, Greensburg, Decatur County, and Unionville, Monroe County. Total production in the state is . hard to estimate, as considerable gas is consumcd in farm homes and for other local uses, and never is reported, but was near 1500 million cubic feet. Some oil from the Trenton field is also used locally and is unreported from pipe-line runs. A total of 606,145 ft. of new hole was drilled in Indiana in 1944. Most of the completions were in Posey and Gibson counties, although wells were drilled in 36 different counties. During the year 331 wells were completed. Of these, 145 found oil in commercial quantities and 28 were gas wells. The initial production of the 145 oil wells was 11,908 bbl. per day. Settled production would be less, of course. The largest wells reported during the year were two on the J. W. Mann farm, in the Mt. Vernon field, with a flush flow of 500 to 800 bbl. each.. Six pools, all small "one well" affairs, were abandoned in 1944; i.e., Fleenor and Patoka in Gibson County, Grafton and Rapture in Posey County, Vaughn in Vandei-bwgh County and Millersburgh, Warrick County.

Jan 1, 1945

By E. S. Machlin

The wzodel of Blandin and Diplunt;, generalized to include a phase factor, is applied to the carbon-carbon interaction in iron. Darken&apos;s "energetic" model is generalized to include not only first neighbor interactions but further neighbor interactions as well. On the bases of these generalized models relations are derived for the activity of carbon in both austenite and ferrite in terms of the carbon-carbon Pair interaction energies. A single function then yields the pair interaction energies consistent with the experimental activities of carbon in both ferrite and austenite. Thus, a simple explanation is given for the observation that the nearest-neighbor interaction between carbon is repulsive in austenite and attractive in ferrite. Certain consequences of this approach are explored. OnE object of the present paper is to attempt to take into account the consequences of electrostatic contributions to the carbon-carbon pair interaction energy for carbon as a solute in iron. Friedel&apos; has shown that oscillations in electrostatic potential are to be expected about a solute atom in a metallic solution. Blandin and 6lant6&apos; have shown that such oscillations yield an interaction energy between pairs of solute atoms that obeys the relation: W{ = A cos(2ftFri + 4>)/(kFri)3 [l] where kF = Fermi wave vector, ri = distance between solute atoms comprising the pair7 <p = phase factor dependent only on electronic nature of solute and solvent, A = coefficient dependent only on electronic nature of solute and solvent. Machlin3 found that Eq. [I] accurately described the pair interaction energy derived from short-range order measurements based on field ion microscope observations of dilute alloys of platinum. He also found that the value of the phase factor $ derived from residual resistivity measurements agreed well with that obtained from the analysis of the short-range order data. Harrison and paskin4 were able to predict the long-range ordering energy of 0 brass using Relation [I] and residual resistivity values to predict the value of the phase factor $. Machlin5 has repeated their analysis and applied it to the prediction of the long-range ordering energy in AgZn and AgCd with excellent agreement between prediction and experiment. Both A and $ are independent of the crystal structure. The Fermi wave vector depends uniquely upon the conduction electron concentration per unit volume in the spherical approximation of the Fermi surface. Thus, Eq. [I] is expected to apply to both fer- rite and austenite with only one set of values of A and $. Mossbauer studies6 yield the result that iron has one 4s electron. We shall make an assumption found to hold previously for platinum3&apos;7 and nikel, which is that only the s electrons are involved in shielding the perturbing potential of carbon. With this assumption, kF = 1.35 A-l. Although A and $ may be obtained from certain mdels&apos;&apos;&apos; we shall take A and $ to be empirical constants in the spirit of Kohn and osko.&apos; Thus, Eq. [I] involves two adjustible parameters. Consequently, two independent relations in A and $I are required in order to evaluate them for carbon as a solute in iron. We may use a recent analysis of Aaronson, Domain, and poundg who showed that Darken&apos;s energetic model,1° as well as others, can be used to describe the activity-temperature data for carbon in iron in both the aus-tenitic and ferritic phases. Darken&apos;s model takes into account only first neighbor pair interactions. For our needs, all neighbor pairs need to be taken into account. It is convenient to generalize Darken&apos;s model. The result for the partition function for austenite is: over the temperature range 800" to 1200°C and where the uncertainty corresponds to one standard deviation. Eq. [4] effectively yields only one relation. Another relation is required to obtain unique values for A and $. One property of Eq. [4] is that it is independent of crystal structure. Hence, data for a iron can be used to obtain another relation. To arrive at this relation we must generalize Eqs. [2] and [3] so that they may be applied to the bcc a iron. The result is that:

Jan 1, 1969

By G. W. Preckshot, N. G. DeLisle, C. E. Cottrell, D. L. Katz

MOST crude oils contain asphaltic substances that may be naturally or artificially precipitated. In the Greeley field, California, this asphaltic bitumen is precipitated during the flow of the oil from the reservoir to the stock tank. The mechanism of such precipitation is not well understood. This paper presents the progress that has been made by using the electron microscope as a new tool and by observing the effects of the streaming potential on the formation of bitumen particles. Crude oils at atmospheric pressure viewed in the electron microscope in very thin films under a vacuum showed no asphaltic particles. A technique of preparing slides of thin films by dilution of the oil with benzene and washing in petroleum ether was used at first, and these observations showed that the solvents caused the formation of the particles, varying from 0.01 to 0.2 micron in diameter. The electrical effects of fluids flowing through porous solid were studied, with emphasis on the formation of colloidal particles by the streaming potential. The streaming potential of crude oil flowing through sand was measured and was shown to be responsible for the formation of bitumen particles. These results bring out a new phenomenon, which may occur when crude oil flows through the porous oil reservoir.

Jan 1, 1942

By M. E. Wadsworth

"For his creative efforts in explaining the electrochemistry of sulfide mineral leaching systems." Leaching reactions that occur during the dissolution of selected base metal sulfides and metals are considered in terms of surface reactions and the influence of intermediate or final products formed. These products may be solid layers, requiring solid phase diffusion for the reaction to proceed, or ions in solution that can influence the kinetics by controlling the mixed potential of the solid. Three general types of reactions are proposed to explain observed rates of reaction. Examples are presented for non-oxidative and oxidative leaching of galena (PbS), anodic dissolution and oxidative leaching of molybdenite (MoS2) and cyanidation of silver and gold.

Jan 1, 1986

By M. C. Leverett

THE dynamic behavior of a multiple fluid system is completely describable in terms of driving forces and resistances to flow. The latter are proportional to the vis-cosity of the fluid under consideration and inversely proportional to a property of the system termed the " effective permeability" to that fluid, a property therefore defined by this relation. Since three phases are usually present in oil reservoirs, it is essential to know the effective permeabilities to the several fluid phases, and the relationship between the composition of the fluid in the pore space and that of the flowing stream, in order to handle satisfactorily certain problems of oil production. In this regard, there are many unknown factors and parameters, and many that can be evaluated only indi-rectly. However, it is expected that work along lines similar to this present under-taking will help materially in solving these problems. Previous workers in this field have inves-tigated the two-phase systems, water-gas,1 water-oil2 in unconsolidated sands, and water-gas3 in consolidated sands. The ex-tension of the study of the flow of hetero-geneous fluid systems from two to three phases involved only slight changes in technique. The apparatus used in the present work, except for slight changes to be described, was that used by Leverett in his water-oil experiments.2 Correlation and interpretation of data were made by methods analogous to those used in two-phase work. The relative permeability to a phase-the effective permeability divided by the permeability of the system to a homogeneous fluid-was employed through-out in correlating the rate of flow of that phase with the composition of the pore space. Quantitative measurements of two inde-pendent physical properties of the system were required to determine the composition of the pore space. As in the two-phase work, the fraction of water was determined electrically. The gas fraction was deter-mined by measuring changes in volume accompanying measured pressure changes. Suitable account was taken of the solubility of the gas in the liquid phases, and of the vapor pressure of the water phase. Since this work was exploratory in nature, no attempt was made to obtain highly accu-rate numerical results. Reasonable precision and reproducibility were sought.

Jan 1, 1940

AT the Tulsa meeting of the A. P. I., the following reso-lutions, expressive of the policy of that organization, were among those adopted: RESOLVED, That we endorse the conclusion of the Federal Oil Conservation Board in its report of September, 1926, that the prevention of the waste of gas incident to the pro-duction of oil is of paramount importance in the conserva-tion and economical production of oil, and the president of the Institute is requested to appoint a committee of seven to devise and suggest to this board, or the executive com-mittee, such measures as will enable the industry, while continuing to meet the consumption requirements for pe-troleum and its products, to conserve in its natural state such reserves of petroleum as may not then be required for consumption. RESOLVED, That the president of the Institute appoint a committee of seven to formulate and recommend to this board or its executive committee, at the earliest practicable date, a program of legislation; Federal and State, to be advocated by the Institute giving sanction and effect to agreements by oil producers for the curtailment of produc-tion in pools where and during periods when there is over-production, having for their purpose the economical and orderly production of oil.

Jan 1, 1927

By A. U. Seybolt

In part 111&apos; of this series it was shown that during the selective oxidation of a 3 1/4 pct Si-Fe alloy in damp hydrogen, only silica, (observed at room temperature) as low cristobalite or low tridy-mite or both, was formed as an oxidation product. In some in- „ stances where the film was fairly thin (probably well under 100A) there was some suggestion of an amorphous form of SiO2. The present investigation of oxidation rate showed that the selective oxidation of silicon-iron can be rather complicated, and apparently impossible to rationalize in an unequivocal manner. In some temperature regions, notably near 800" and 1000°C, the data seem to obey the familiar parabolic rate law. However, at intermediate temperatures complications were noted, some of which are possibly due to the order-disorder reaction in the silicon-iron solid solution. IN an earlier report&apos; it was shown that during the oxidation of 3 1/4 pct Si-Fe alloys in H2O-H2 atmospheres only silica films were formed in the temperature range from 400° to 1000°C in hydrogen nearly saturated with water at room temperatures, or at dew points as low as -45°C. In the work to be reported here, some observations are made on the rate of oxide film formation. As in the earlier investigation, electron diffraction patterns generally showed either low tridymite or low cristobalite or both, except for some very thin films. These sometimes showed diffuse rings, presumably due to a very small crystallite size, or in a few cases, diffuse bands probably caused by an amorphous film. EXPERIMENTAL PROCEDURE Vacuum-melted silicon iron made of high-purity materials was rolled into strips 0.014 in. thick, and cut into samples 1/2 in. wide by 1 in. long. Chemical analysis showed 3.2 pct Si and 0.002 pct C. All samples were surface abraded with 600-grit paper, were solvent cleaned, and then placed in an paper,apparatus containing a "Gulbransen type"2 micro-balance. Here the gain in weight of the samples of about 5 sq cm area could be followed as a function of time during the oxidation caused by the water in atmospheres of various controlled water-hydrogen ratios. The water-hydrogen ratios can most easily be described as varying from a dew point of 0°C (PH2O-p^2 = 6.2 x 10-3 , to K (P j -40°C (PH2O/PH^= 1.3 X 10-* Most of the experiments were conducted at the 0°C dew-point atmosphere because drier atmospheres caused so little gain in weight that the accuracy of measurement was poor. Because of this, only the data obtained at PH2O,/P,,,= 6.2 x X3 will be reported. The temperature range extended from 800" to 1000°C; and most of the oxidation runs lasted for about 24 hr. The reproducibility of any reading was about ± 1 ?, but the sensitivity of the balance was about 0.2 ?. The atmosphere, flowing at 200 cm per-min, was preheated to the furnace temperature before contacting the specimen. While the gas flow caused a measurable lift on the sample, it was ordinarily sufficiently constant so that it was not an appreciable source of error. X-ray and electron diffraction checks of the samples before and after oxidation showed no evidence of preferred orientation, either on the metal samples or on the silica films formed. EXPERIMENTAL RESULTS The data obtained are summarized in Table I, and some are given in detail in Figs. 1 to 4. In the fourth column of Table I, kp refers to the parabolic rate constant in the expression (?/cm2)2 = kpt + c [1] where ? = micrograms gain in weight kp = parabolic rate constant in units r2 /cm4 t = time in minutes c = constant It will be noted that in many cases no value for kp is given; this is because in these instances the data did not obey the parabolic rate law. The silica film thicknesses given in the last columns are values calculated from the weight gain, an average tridy-mite-crystobalite density, and by assuming a perfectly plane surface. Fig. 1 shows the data plotted in the form of Eq. [I], hence a linear plot indicates parabolic behavior. It has been frequently observed in the literature that

Jan 1, 1960

• "This country eventually may have to rely on foreign sources for some metals, not because it does not have them here but because it may have difficulty getting the labor to mine them. Few people realize the extent to which the &apos;old timers&apos; are still the backlog of the important districts." --Fred Searls, Jr. • A new filter has been developed by Arthur D. Little, Inc., for the ABC which will remove all dust from the air. Submicroscopic asbestos fibers are used as filter media and are claimed to stop all dust and pollen while passing suitable quantities of air. •Out in front public relationswise is the Peabody Coal Co. which has launched a 15-min television news program on WNBQ at 10:30 C.S.T., Tuesday and Thursday nights. Clifton Utley, news commentator, will tell how coal is mined today and indicate, with pictures, the improvement in efficiency and safety which has resulted from today&apos;s mechanized operations. •Two hundred coal mining companies are using roof bolts as a means of supporting about 14 million sq ft of roof surface, Edward Thomas of the Bureau of Mines reported. Various types of metal and wooden pins can be used. The method was first used by the St. Joseph Lead Co. over 20 years ago, but is now being studied and adopted widely in metal, nonmetallic, and coal mines. * The first ten technical graduates have reported at Hanford Works in the state of Washington, to begin the newly installed General Electric rotational training program, believed to be the first of its kind at any U.S. atomic energy plant. The program is to provide suitably trained personnel for the nation&apos;s atomic energy program. •The need for top-notch scientists and engineers to stimulate mining programs in British colonies is acute. About 60 American experts are being sought for the ECA sponsored program. Positions for mining engineers, geologists, assayers, topographers, and petrologists are open. •Production of primary aluminum for the first quarter of 1950 was 322,4250008 lb which is 6 1/2 million lb more than was produced in the first quarter of 1949. Shipments of aluminum sheet, plate, and strip amounted to 259.772,1571b for the first quarter. •Policy on manganese procurement for the stockpile is being studied by a House Armed Services Subcommittee with the possibility of lowering specifications. The U. S. Bureau of Mines is drafting a bill to encourage domestic production for stockpiling through producer subsidies. &apos;It will have to be cleared by the Bureau of the Budget and other agencies before going to Congress. •Oil men consider dry holes a necessary evil in their search for oil. Last year 34 out of every 100 wells drilled were dry holes. Yet Texas Technological College is attempting to drill a dry hole on its campus at Lubbock, taking every precaution to make sure it is a "duster" so its petroleum engineering students can play around with experiments without being bothered by any messy crude oil. --Natural Resources Notes. •A portable alertness indicator which signals lethargy in persons doing monotonous jobs has been developed for the Navy&apos;s Special Devices Center. A possible application to hoistmen is indicated but broaching the matter to them would be tricky.

Jan 6, 1950

By W. C. Shanks

Seventeen deeps, which contain hot or cold brines and/or metalliferous sediments, have been discovered in the axial rift zone of the Red Sea. Metalliferous activity results from the unique geological setting of this incipient ocean basin: oceanic crust intruding in a central rift zone flanked by thick evaporite sequences. Brine pools tend to occur in structural depressions where- transform faults intersect the spreading axis. The most significant metalliferous occurrence is in the Atlantis II Deep, which contains approximately 227 Mt (dry weight) of metalliferous sediment which averages 1.04% Zn and 0.28% Cu. Higher potentially economic grades (3-6% Zn, 1% Cu, 50 glt Ag) occur in the Southwest Basin of the Atlantis II Deep, comprising total metal tonnages of 1.7 Mt Zn, 0.4 Mt Cu, and 5000 t Ag. The Pre-Pilot Mining Test conducted in 1979 raised 15 000 m3 of mud by a slurry process and demonstrated the feasibility of mining, concentration by froth flotation, and tailings disposal at sea. A Pilot Mining Test is scheduled for 1983-1984. The metalliferous discoveries in the Red Sea provide a model example of deep marine mineral exploration. Detailed mapping of bottom bathymetry and brine-interface reflectors using a high-resolution narrow-beam echo sounder has been the most effective exploration tool in the Red Sea. Followup coring has discovered additional metalliferous deposits in basins without present-day brines, and potential exists for additional discoveries. Geochemical exploration using heavy metals values in sediments (iron, manganese, zinc, copper, and mercury) and sulfur isotope values of sulfides are considered to be the most promising techniques for discovery of currently inactive deposits. Positive sulfur isotope values in the range I to 17 are an indication of hydrothermal sulfides in the Red Sea, and there is considerable contrast from back- ground bacteriogenic sulfides ( - 10 to - 45).

Jan 1, 1983

By W. B. Wise, H. D. Attra, W. M. Black

The purpose of this paper is to illustrate a comparatively new approach for solving a problem that has plagued oil producers for many years—how to make the most money with available field production capacity. In a very basic operation such as a top-allowable one-well field, a computer and staff of engineers are not required to determine that the best operation is to produce that well at its maximum for as long a time as it will produce. However, as the problem becomes more complex and the number of wells and number of reservoirs increase, it probably will be a wise choice to devote some engineering thought and calculation time to determine the best way to operate that field on both an ultimate and day-to-day basis. Continued developments in the field broadly referred to as "operations research" have led to a number of useful engineering analyses for optimizing field operational problems. One of these techniques, termed linear programing, is parlicularly interesting because of its potential applications to the study of complex oilfield operating problems. Linear programing is concerned with the problem of planning a complex set of interde~endenl activities in the best possible (optimal) fashion. A field application of linear programing is being used to maximize daily income from a multi-reservoir producing operation. The initial results of this study indicate that the linear programing technique (I) can be applied effectively to field problems, (2) can be used to detect unsuspected avenues for improving operations and (3) can effect a significantly improved means of controlling field operations through the use of the highspeed computer. INTRODUCTION The usual approach for studying complex field operational problems has been to look in detail at several basic plans suggested by judgement and experience and, then, to choose the best plan from those investigated. This approach is entirely satisfactory provided: (1) that judgment and experience alone will reliably pick the best or near the best program as one of the plans to be investigated; and (2), and most important, that the factors which control field production will not change. This paper deals with the large group of field operations which are at least one-step removed from a satisfactory solution using the conventional method of analysis. Problems such as pipeline- and gathering-system design, transportation studies, large field development projects and multi-reservoir producing operations fall in this latter category. To find the best program for handling these problems when the best program is not obvious, a complete optimization study is required, and high-speed computers are required to continually update the program once it is selected. Operations of this type have an extremely large number of possible solutions. However, only one will result in maximum economic return and, more important, this one program must be re-evaluated and adjusted constantly to accomodate such changing field factors as the number of producing days, the price of crude, the discovery of new reserves, declining reservoir pressure with subsequent decline in production and a host of other factors which characterize specific operations. One of the most widely used, direct methods of optimization is a numerical procedure termed "linear programing", which is designed to investigate systematically each of the possible solutions involved in a given problem, determining rapidly and uniquely the optimum answer. As implied by the name, linear programing requires that all field variables be either defined or expressed in a series of interdependent linear equalities or inequalities. These relationships are solved simultaneously, using a form of matrix solutions to determine the optimum values for each producing variable that will maximize net profits. The solution techniques used in a recent field case study is termed the "simplex method" and is discussed in full detail in Ref. 1.

By R. W. Raymond

The absence of a convenient glossary- of terms connected with mining and metallurgy has long been felt by the general public. It is to meet this want, not to furnish a technical manual for experts, that the following glossary has been prepared. It originated in an attempt on my part to revise for publication the manuscript of a compilation prepared from the appendix of Yale&apos;s work on Mining Titles and one or two other sources, to serve as an appendix to a new work on mining law, about to be published by Mr. H. N. Copy, of Washington, D. C. This revision soon assumed, contrary to my original intention, the proportions of a reconstruction; and with the consent of Mr. Copp, and for the purpose of receiving from my fellow-members valuable aid, I presented my still incomplete work as a paper at the Lake Superior meeting of the Institute, inviting from any quarter suggestions of new terms or better definitions to be incorporated in the glossary before its final publication. This invitation was so widely and generously responded to, that I cannot undertake to make in this place individual acknowledgments to those members of the Institute, and professional colleagues outside of it, who have favored me with assistance and advice. The labor bestowed upon this paper since its presentation at the Lake Superior meeting has considerably exceeded that of its first preparation, as

Jan 1, 1881

By Paul D. Merica, R. G. Waltenberg

Although nickel was discovered and isolated as early as 1750 and its valuable properties recognized, many years passed before it was used commercially for wire, sheet, rods, etc., in the pure form. This was due partly to its high cost at that time and partly to the fact that it was not possible to refine and cast nickel into ingots sufficiently malleable to be amenable to the usual forging, rolling, or drawing processes. So remarkable was this fact, and so different from the experience at that time with metals such as copper and iron, that it has left its impress on the nomenclature within the nickel industry. To this day, furnace-cast nickel produced in such a manner as to be suitable for rolling and forging is called malleable nickel to distinguish it from the ordinary pig and shot nickel of commerce. In 1878, the firm of Jos. Wharton, of Philadelphia (which later became The American Nickel Works, a constituent of The International Nickel Co.) exhibited at the Paris Exhibition specimens of rolled pure nickel strip and of drawn nickel wire. About this time, there was considerable activity in the study of the refining of nickel and several methods were described, some of which were patented, for the production of furnace-cast malleable nickel including the use of manganese (Boed-dicker,1 Selve and Lotter2), the use of potassium permanganate (Berns-dorfer Metallwarenfabrik3) and the use of phosphorus (Garnier4). By far the most efficient method was discovered by Th. Fleitmann in 1879;5 it consisted in adding to the molten nickel, just before pouring the castings, from 0.05 to 0.125 per cent. of metallic magnesium. This soon became the recognized final malleableizing treatment for furnace-cast nickel.

Jan 1, 1925