Search Documents

By Colin G. Fink, Leslie G. Jenness

Tantalum and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTaz06), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore,becoming (Pe, Mn)O.(Ta, Cb)2Os. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and si1ica. l Methods of Extraction Several methods have been proposed for the extraction of tantalum and columbium from their ores, among them being: 1. Fusion with Potassium or Sodium Bisu1fate.—The finely ground ore is fused with potassium bisulfate, after which the mass is boiled with water and the fusion repeated several times. The residue finally resulting is digested with ammonium sulfide to remove traces of tin and tungsten, boiled with hydrochloric acid, filtered and washed. These oxides are then dissolved in hydrofluoric acid, the silica evolved as silicon tetra-fluoride and the hydrofluoric acid solution used for the potassium double fluoride separation of tantalum. 2. Fusion with Sodium Carbonate and Sodium Nitrate.2—This fusion renders the tantalum and columbium soluble, and they are extracted

Jan 1, 1931

By T. K. Perkins, W. W. Krech

Jan 1, 1969

By J. D. Mote, A. Rosen, J. E. Dorn

The effect of strain rate and temperature on the critical resolved shear stress for (1100) [1120] prismatic slip was determined for the intermediate hexagonal phase containing about 67 at. pct Ag and 33 at. pct Al. Whereas the flow stress increased only slightly as the test temperature was first decreased below room temperature, a rapid increase inflow stress was obtained with yet greater decreases in temperature from about 240" to 4°K. The effect of both temperature and strain rate on the flow stress over the low-temperature range could be completely rationalized in terms of the Peierls mechanism when the deformation is controlled by the rate of nucleation of pairs of kinks. A few years ago Mote, Tanaka, and Dorn1 observed that the critical resolved shear stress for prismatic slip of a 67 at. pct Ag plus 33 at. pct A1 hexagonal intermediate phase by the (1100)[1120] mode decreased precipitously as the test temperature was increased from 4" to about 160°K. Their results for both basal and prismatic slip are given in Fig. 1. It is obvious that only the flow stress for prismatic slip is strongly temperature-dependent, whereas the flow stress for basal slip is independent of temperature. If the temperature dependence of the flow stress were primarily due to interstitial impurities, it might be expected that they would influence the flow stress for basal slip as well. Since the activation volume at 115°K for prismatic slip was determined to be about 15b3, where b is the Burgers' vector, this thermally activated deformation process was tentatively ascribed as being due to the Peierls mechanism. But the various analyses of the Peierls mechanism then available as formulated by Seeger2 and also by Lothe and Hirth3 did not agree well with the experimental data. Since that time a more realistic theory for the operation of the Peierls mechanism under conditions where the strain rate is determined by the rate of nucleation of pairs of kinks has been presented by Dorn and Rajnak.4 The present investigation was, therefore, undertaken in order to provide the essential data for a careful check on the agreement between this theory and the low-temperature deformation by prismatid slip of the above-mentioned Ag2A1 intermediate phase. EXPERIMENTAL TECHNIQUE Single-crystal specimens so oriented that the [1120] direction and the normal to the (1100) plane were at 45 * 2 deg to the tensile axis were grown from the congruent melting composition of about Ag2Al for the intermediate hexagonal phase by the

Jan 1, 1964

By Robert Mehl

THE system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that FIG. 1.-BIJL'S DIAGRAM FOR CADMIUM-MERCURY ALLOYS. developed by Bijl1 (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1929

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By H. W. Rogers

THE first steam shovels used in this country were built by the Otis Company, of Boston, about 50 years ago, but as they were of very crude construction and rather unsuccessful only a few were built. For possibly 10 years prior to 1884 successful steam shovels were made and used on certain classes of work, but it was not until that time that they were manufactured in quantities and began to play an important part in all classes of excavation. From that time up to the present day there have been gradual but continuous improvements on the original shovel, not only in the mechanical construction, but also in the design of boilers and engines which are best adapted to this class of service. In proposing a change from steam to electric operation we have to deal with a steam equipment which has not only proved its worth but has probably reached its highest stage of development and efficiency. That the electric shovel is a possibility cannot be denied, as at present from 12 to 18 shovels are in operation in this country. These shovels may be divided into three classes: the friction electric, which is operated by a single constant-speed motor with friction clutches; the three or four motor direct-current equipment, and the three or four motor alternating-current equipment. It is the second and third classes that I wish to deal with, as the first class does not compare favorably with the steam shovel so far as speed is concerned, although it may be operated as cheaply. There is probably no other class of machinery that presents a duty cycle as severe as that of the shovel, which is very short, varying from 7 to 12 sec. on the hoist, from 7 to 12 sec. on the thrust, and from 10 to 18 sec. on the swing, making a complete cycle in from 17 to 30 sec., and the motor to meet these requirements must have a sufficiently low armature inertia to permit of rapid acceleration and quick reversals under small power. It should also be a motor of rugged design, as it must be subjected to severe overloads and shocks and frequent reversals. This is especially true of the hoist motors and, to a lesser degree, of the swing motor; the thrust motor being practically stalled during the digging operation, although it may revolve or overhaul, according to conditions, and is operated at full speed only after the hoisting operation is completed.

Jan 2, 1914

By R. H. Pemberton

The principle of airborne electromagnetic prospecting is well-known. The basic geophysical texts in most cases discuss the main elements involved in electromagnetic prospecting. However, there is certainly little information available to the public concerning the present types of airborne electromagnetic systems being flown today by both contracting companies and some of the mining companies which have their own instruments. This is unfortunate since it is difficult for those people not conducting such operations to understand thoroughly the large variation in the electromagnetic instruments available.

Jan 1, 1961

By W. Mckewan, W. M. Fassell

The oxidation rates of copper have been determined at temperatures from 600" to 900°C in oxygen from 14.7 to 400 psi total oxygen pressure. The oxidation rate of copper is unchanged by oxygen pressures within the range studied. The observed data extend Feit-knecht's conclusion concerning the pressure independence of copper from atmospheric pressure to 400 psi. All samples studied in the above-mentioned temperature and pressure range have both Cu2O and CuO present in the oxide film. NUMEROUS papers have been published on the oxidation of copper, some of which have noted the effect of oxygen pressure on the oxidation rate of copper. It must be noted, however, that no data on the oxidation rates of copper at pressure in excess of 1 atm have been reported in the literature. (Le Chatelier¹ reported that a black oxide of silver was formed at 300°C and 15 atm pressure.) This is likewise true for the other metals. This investigation was initiated to obtain experimental oxidation rate constants for pure metals at elevated temperatures and high oxygen pressure. Copper was selected as the first metal since probably more reliable data are available on its oxidation rates and related physical and chemical properties than for any other metal or alloy. As a general summary, the following conclusions appear well established for the oxidation of copper: 1—The oxide coating consists of Cu2O with a superficial coating of CuO providing the ambient oxygen pressure exceeds the equilibrium pressure for the coexistence of Cu2O and CuO.² The following sequence of phases is then Cu/Cu2O/CuO/O2 (gas). The Cu2O consists of large crystals that have no relation to the orientation of the metal crystals, except for a very thin layer adjacent to the metal." The CuO consists of very fine crystals randomly oriented. If the oxygen pressure is below the equilibrium pressure for the coexistence of Cu2O and CuO, the coating consists of Cu,O only. 2—The rate-determining factor in the parabolic oxidation of copper is the diffusion of Cu+ ions through the Cu,O layer.4,6,7 The Cu+ ions are accompanied by electrons to maintain electrical neutrality. The mechanism of the reaction at the Cu2O/CuO interface and the method of growth of the CuO is in some doubt. 3—On copper, there are three reported pressure effects: (a) At pressures below 0.3 mm Hg oxygen pressure, the oxidation rate increases directly with pressure.', ' .Vxygen starvation at the surface may account for this effect. (b) At oxygen pressures from 0.3 to 63 mm, the oxidation rate increases as the 7th root of the oxygen pressure providing the temperature is such that only Cu2O is present in the film. (c) At pressures from above the equilibrium pressure for the coexistence of Cu2O and CuO (varies with temperature) to atmospheric pressure, the oxidation rate is independent of the oxygen pressure.' Equipment In order to determine the oxidation rates of metals in an oxidizing atmosphere at pressures up to 400 psi, the equipment is somewhat different than for low pressure work as is shown in Figs. 1 and 2. A Leeds and Northrup Micromax recording controller (A) is used to control the temperature of the Ni-chrome furnace winding in conjunction with a Micromax electric drive unit. The drive unit adjusts a 20 amp Variac (variable transformer) to control the power input into the Nichrome furnace winding. Due to the "self heating" of the sample by oxidation, frequently encountered in oxidation rate studies, it is essential that the sample temperature be measured independently. This is done by means of a series of six chromel-alumel calibrated thermocouples located spirally around the oxidizing metal sample. Each thermocouple is partially shielded from the direct radiation of the furnace wall by

Jan 1, 1954

By C. M. Shigley

The record of the largest magnesium plant in the country utilizing sea water as a primary raw material stands as another victory in the struggle for large-scale production of pure chemical elements from the oceans. Bromine was the first element to be economically and commercially recovered when, in 1933, a six million pound per year unit was built on the Atlantic Coast near Wilmington, North Carolina, by the Ethyl-Dow Chemical Co.' The bromine was reacted with ethylene to produce ethylene dibromide, a necessary associate of tetraethyl lead in ethyl antiknock fluid. Within eight years that plant was doubled and redoubled, and another large unit was put into operation at Freeport, Texas, taking bromine from the Gulf of Mexico. In 1940, in fortunate anticipation of the impending demand for magnesium and the limitations of the production from natural brines, the Dow Chemical Co. turned again to the sea, and designed and erected a plant at Freeport to produce 18,000,000 lb. of magnesium per year from sea water.2 In March 1941, two months after the new plant had been put into successful operation, construction of an 18,000,000-lb. Government-financed addition was started. Late in 1941, as a part of the $400,000,000 defense program intended to produce 600,000,000 to 700,000,000 lb. of magnesium per year, Dow was asked to build and operate for the Government a 72,000- ooo-lb. plant near its original plant at Freeport. Within a few days after the Japanese made their attack at Pearl Harbor, preparation of a site was started at Velasco, Texas, for the construction of the Texas plant of the Dow Magnesium Corporation—the largest known magnesium plant utilizing sea water as its raw matcrial. Less than six months after the first piling was driven, urgently needed magnesium was in steady production. Five months later, the plant had exceeded its rated capacity. It remained above rated production until the general magnesium curtailment was applied to Government-owned plants in September 1944. Credit for the construction and operation record of the Dow magnesium plant must be divided among the efforts of a very determined group of men, an extremely favorable location, and a simple process. It is with the two latter aspects of the plant that this article will deal. The site for the new enterprise was chosen near Velasco, Texas, on property bordering the Brazos River at a point approximately 6 miles inland from the original magnesium plant and 7 miles inland from the Freeport Harbor on the Gulf of Mexico. This location was far enough away from the operating units to reduce both interference from construction and the vulnerability of closely bunched manufacturing operations to the then feared air attack. Yet the distance inland was not too great for the economical construction of a barge canal from the harbor to serve both the transportation of raw

Jan 1, 1949

By G. L. Oldright

THE upper limit of richness of concentrates that can be smelted by means of the blast furnace without added diluents is fixed by the opera-tion of sintering. A sinter feed with normal gangue constituents, con-taining more than about 50 per cent of lead, tends to fuse; as a result, air does not come sufficiently into contact with the sulphides at roasting temperatures, and sulphur elimination is poor. Since most lead con-centrates now contain 55 to 80 per cent lead, it is necessary to add diluents to lower the grade of such sinter feed to about 50 per cent or less. This not only entails the expense of providing barren diluents when adequate diluents containing precious metals are not available but also appreciably lowers the capacity of the blast furnace to produce lead and increases slag losses. Attempts to desulphurize rich lead concentrates by methods other than sintering have not proved successful. Flash roasting, for example, converts much of the lead sulphide to lead sulphate rather than to oxide. However, this suggested the possibility that deliberate flash roasting of the concentrates to sulphate, followed by sinter roasting of the resulting product, might prove promising, particularly inasmuch as the elimination of sulphur from lead sulphate requires heat alone and not contact with atmospheric oxygen. The sintering of lead sulphate products has additional interest because important amounts of such products are now treated by lead smelters. Considerable quantities of lead sulphate are present in rich lead flue dusts and other by-products; lead-chamber sulphuric acid plants and other

Jan 1, 1940

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By L. Graydon Carpenter, Donald E. Garrett

Probably the largest single tungsten deposit in the U. S. is one that has yet to produce any tungsten; it is not even listed in tables showing U. S. reserves. This deposit is at Searles Lake, Calif., where the brine contains about 70 ppm WO3. Small though the concentration is, the amount of brine in the lake is so great that it is estimated at 170 million lb of WO3 (8.5 million units), equaling the total of all other known reserves in the U. S. This dry lake is located in the basin formed by the Argus and Slate ranges in the northeastern corner of the Mojave Desert (Fig. 1). It consists of a massive salt body some 35 sq miles in extent, varying in thickness from 0 to 120 ft and containing more than 3 billion tons of salt. A central section of about L. G. CARPENTER and D. E. GARRETT are with the Research Dept., American Potash & Chemical Corp., Trona, Calif. TP 47881. Manuscript, Nov. 4, 1958. AlME Trans., Vol. 214, 1959. 8 sq miles is exposed salt; the remaining area is overlain by mud. Except for the exposed sodium chloride (10 to 15 ft thick) the body consists of a very complex and heterogenous mixture of soluble crystals, containing at least eight major phases. It is only about 53 pct solid, the voids being occupied by a dense brine which is the raw material for two chemical companies operating in the valley.

Jan 3, 1959

By A. W. Ambrose

THE underground losses of oil exceed by hundreds of thousands of barrels all the oil that has been lost in storage, transportation, or refining. The quantity lost is, of course, indeterminate; but when it is considered that the contents of an entire oil field have been excluded from recovery by invading waters, some idea of the amount wasted may be gained. Similarly, enormous quantities of gas have been lost underground. Conservation of the oil, therefore, should start before it is brought to the surface rather than after it is placed in storage tanks. Water is one of the most important causes for underground losses and the operator should give as serious consideration to an underground flood of water as he would to a destructive surface flood. The best insurance, of course, is to have the wells drilled in such a manner that water has no access to the productive oil and gas horizons, and on abandonment the wells should be properly plugged. The encroachment of edge water and the occurrence of water in the base of an oil sand present a very serious problem to an oil company; sooner or later these waters are bound to cause considerable damage, if they do not entirely destroy the possibilities of further production. Too often, however, a field has been considered to be in a hopeless condition, whereas wells in as bad a condition in other areas have been repaired and the life of the field appreciably lengthened. The corrections are very often suggested by technical study. Very successful results have been accomplished by detailed underground work in the California oil fields, in Cushing, Oklahoma, and in other areas.

Jan 9, 1920

By Nicholas J. Grant, A. W. Mullendore, Paul Predecki

The Duwez technique of splat cooling in which a molten droplet of metal is accelerated and made to impact on a cold, highly conducting substrate was investigated.- An apparatus for producing "splat" was constructed employing an explosive powder charge to accelerate the molten metal. Transport of the molten metal just prior to impact with the substrate was studied by means of high-speed photography. The molten particles are small spherical droplets from about 1 to 50 µ diameter. The average cooling rates for aluminum, silver, and a gold alloy splatted on nickel substrates at room temperature were determined experimentally and were found to vary from 18 to 5 x 10' C per sec. The heat-transfer coeficients for pure aluminum and pure silver splats cooled on nickel substrates at room temperature were found to be 2.7 to 6.8 and 13.6 to 54.2 cal per sec sq cm 'C (2 to 5 x 104 and 1 to 4 x 18 Btu per hr sq ft OF), respectively. Solidification rates in pure aluminum and silver splats were calculated. "SPLAT cooling" is a term describing a technique for extremely rapid freezing and cooling of molten metals and alloys to room temperature or below. The technique was developed by Duwez et al.' in 1960, and after refinement2 consisted in transferring a few tenths of a gram of molten metal to near sonic velocity to strike a suitably placed cold copper surface. Upon impact, the metal spread into a thin nonuniform film called a splat, about 10-4 cm thick. The splat particles produced in this manner were thin enough in some areas to be suitable for transmission electron microscopy, without further treatment, and, together with X-ray data, yielded a variety of structures which would be classified as follows: 1) supersaturated solid solutions (increase in solubility limit), 2) metastable crystalline stoichiometric and non-stoichiometric intermediate phases ( in Au-20.5 at. pct Si and in Au-14 at. pct Sb, respectively), 3) amorphous alloys, 4) retained high-temperature phases, 5) alloys having equilibrium phases present, but with unusual, markedly altered structures. The crystalline phases present in splats were usually extremely fine-grained and had low dislocation densities. Present interest in splat cooling centers around a study of the unusual structures produced by the technique, their contribution to alloy theory, and the possibility of the development of new or unusual properties. In addition, the technique is being examined for the production of bulk quantities of new high-strength alloys for low- and high-temperature use. Although a number of alloy systems have already been investigated by the technique, relatively little is known about the mechanism of splat formation and the physical conditions encountered by the metal during solidification and cooling. The purpose of this work was: 1) to determine the velocity, shape, and size of the molten metal droplets just prior to impact with the cold substrate; 2) to try to estimate or measure solidification rates, heat-transfer coefficients, and cooling rates in splats. EXPERIMENTAL TECHNIQUE Splatting Apparatus and Procedure. An apparatus similar to the type originated by Duwez et a1.,2 but employing an explosive charge to accelerate the molten metal, was used. A "Ramset" fastening tool (a gun normally used for driving studs into concrete, steel, and so forth) was mounted vertically above a resistance-heated graphite crucible as shown schematically in Fig. 1. A splat product was produced by melting a few tenths of a gram of metal at the position shown in Fig. 1, and then exploding a powder charge in the breach. The shock wave thus generated traveled down the barrel into the furnace, ejecting the molten metal through the 0.06-in.-diameter hole at the bottom of the crucible. The ejected metal was impacted on a high-conductivity metallic substrate where it formed a splat. High-Speed silhouette Photography. In order to investigate the size and shape of the ejected, molten metal just prior to impact with the cold substrate, high-speed silhouette photographs were taken, and are shown in Figs. 2 and 3. These photographs were obtained with the aid of an Edger-ton, Germeshausen, and Grier microflash unit and a submicrosecond flash drive equipped with a variable time delay. Two types of triggers were

Jan 1, 1965

By K. S. Lane

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse. VAIONT RESERVOIR SLIDE Fig. 1 shows Vaiont Dam in Italy which is a double curvature arch, 875 ft high, located on a tributary of the Piave River, north and west of Venice. When completed in 1960 it was the highest arch dam in the world. In 1960 a sizable landslide (some 700,000 cu yd) occurred on the left abutment a short distance above the dam. Following this, the reservoir was held down for construction of a by-pass tunnel through the right valley wall to insure connection with the upper end of the reservoir in event of further slides. In October 1963 a giant landslide occurred on the left valley wall, over a width of some 14 miles (see Fig. 2). Over 300 million cu yd slid into the reservoir, displacing the water and forming a hige wave 700 ft above the top of the dam as it hit the opposite, or right, wall of the valley. The wave then passed some 500 ft over top of the dam, followed down the tortuous winding canyon and debouched into the

Jan 1, 1967

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By Eugene McAuliffe

The term "mechanical mining" carries an ambiguity which justifies a preliminary word of explanation. . All mining activity conducted in this day is more or less mechanical; that is to say, power expressed in the form of electricity, steam or compressed air is used in some portion of practically every mining activity of consequence. "Mechanical loading" is more nearly correct than "mechanical mining" in reference to present practice. The first substantial effort made in the direction of mechanical mining, subsequent to the application of steam for hoisting and underground pumping purposes, was that of substituting for hand labor undercutting and shearing by power-driven machines. The undercutting of coal by hand represented at one time the most arduous task confronting the miner. Occupying a kneeling position in the thicker beds, or lying on his side in the thinner coal, the task was tedious and exhausting. The first attempt to substitute crude air-driven, and later electrically driven, "punchers," as the percussion type of machine was called, met with much the same opposition on the part of the workers as was expressed by workers in the other industries when any innovation, whether labor-saving or otherwise, was introduced. We should not be too critical of this attitude of mind shown by the mine workers. The peculiarly isolated character of the work carried on in semidarkness by a class of men who to a large extent lived and held themselves aloof from the other branches of society led long ago to the development of a craft consciousness which they have found difficult to surrender. It was not until 1891 that a definite record of the results obtained by the use of undercutting machines of all types was made available, the quantity undercut in that year totaling 6,211,732 tons of bituminous coal from all American mines. The volume of bituminous coal undercut by machines in 1928 totaled 369,687,007 tons, or 73.8 per cent. of the nation's production. In the light of this experience, we can properly feel that the work of introducing the coal-loading machine as a substitute for hand shoveling is making substantial progress.

Jan 1, 1931

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937