Search Documents

By Colin G. Fink, Leslie G. Jenness

Tantalum and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTaz06), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore,becoming (Pe, Mn)O.(Ta, Cb)2Os. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and si1ica. l Methods of Extraction Several methods have been proposed for the extraction of tantalum and columbium from their ores, among them being: 1. Fusion with Potassium or Sodium Bisu1fate.—The finely ground ore is fused with potassium bisulfate, after which the mass is boiled with water and the fusion repeated several times. The residue finally resulting is digested with ammonium sulfide to remove traces of tin and tungsten, boiled with hydrochloric acid, filtered and washed. These oxides are then dissolved in hydrofluoric acid, the silica evolved as silicon tetra-fluoride and the hydrofluoric acid solution used for the potassium double fluoride separation of tantalum. 2. Fusion with Sodium Carbonate and Sodium Nitrate.2—This fusion renders the tantalum and columbium soluble, and they are extracted

Jan 1, 1931

By W. Mckewan, W. M. Fassell

The oxidation rates of copper have been determined at temperatures from 600" to 900°C in oxygen from 14.7 to 400 psi total oxygen pressure. The oxidation rate of copper is unchanged by oxygen pressures within the range studied. The observed data extend Feit-knecht's conclusion concerning the pressure independence of copper from atmospheric pressure to 400 psi. All samples studied in the above-mentioned temperature and pressure range have both Cu2O and CuO present in the oxide film. NUMEROUS papers have been published on the oxidation of copper, some of which have noted the effect of oxygen pressure on the oxidation rate of copper. It must be noted, however, that no data on the oxidation rates of copper at pressure in excess of 1 atm have been reported in the literature. (Le Chatelier¹ reported that a black oxide of silver was formed at 300°C and 15 atm pressure.) This is likewise true for the other metals. This investigation was initiated to obtain experimental oxidation rate constants for pure metals at elevated temperatures and high oxygen pressure. Copper was selected as the first metal since probably more reliable data are available on its oxidation rates and related physical and chemical properties than for any other metal or alloy. As a general summary, the following conclusions appear well established for the oxidation of copper: 1—The oxide coating consists of Cu2O with a superficial coating of CuO providing the ambient oxygen pressure exceeds the equilibrium pressure for the coexistence of Cu2O and CuO.² The following sequence of phases is then Cu/Cu2O/CuO/O2 (gas). The Cu2O consists of large crystals that have no relation to the orientation of the metal crystals, except for a very thin layer adjacent to the metal." The CuO consists of very fine crystals randomly oriented. If the oxygen pressure is below the equilibrium pressure for the coexistence of Cu2O and CuO, the coating consists of Cu,O only. 2—The rate-determining factor in the parabolic oxidation of copper is the diffusion of Cu+ ions through the Cu,O layer.4,6,7 The Cu+ ions are accompanied by electrons to maintain electrical neutrality. The mechanism of the reaction at the Cu2O/CuO interface and the method of growth of the CuO is in some doubt. 3—On copper, there are three reported pressure effects: (a) At pressures below 0.3 mm Hg oxygen pressure, the oxidation rate increases directly with pressure.', ' .Vxygen starvation at the surface may account for this effect. (b) At oxygen pressures from 0.3 to 63 mm, the oxidation rate increases as the 7th root of the oxygen pressure providing the temperature is such that only Cu2O is present in the film. (c) At pressures from above the equilibrium pressure for the coexistence of Cu2O and CuO (varies with temperature) to atmospheric pressure, the oxidation rate is independent of the oxygen pressure.' Equipment In order to determine the oxidation rates of metals in an oxidizing atmosphere at pressures up to 400 psi, the equipment is somewhat different than for low pressure work as is shown in Figs. 1 and 2. A Leeds and Northrup Micromax recording controller (A) is used to control the temperature of the Ni-chrome furnace winding in conjunction with a Micromax electric drive unit. The drive unit adjusts a 20 amp Variac (variable transformer) to control the power input into the Nichrome furnace winding. Due to the "self heating" of the sample by oxidation, frequently encountered in oxidation rate studies, it is essential that the sample temperature be measured independently. This is done by means of a series of six chromel-alumel calibrated thermocouples located spirally around the oxidizing metal sample. Each thermocouple is partially shielded from the direct radiation of the furnace wall by

Jan 1, 1954

By Orson Shepard

THE leaching method that was first widely used with the cyanide process consisted of percolation leaching of crushed ore in vats or leaching tanks. It was frequently necessary to separate the sand for cyanide treatment and discard the slimes, because only granular material allows the necessary amount of solution to percolate through it in a reasonable time. Later a slime process consisting of agitation followed by thick-ening and filtration was developed, and is extensively used to the pres-ent day. Even though the agitation-leaching slime process is considered satis-factory, the cost of plant and of operation are both greater than for a percolation-leaching plant of equal capacity. This situation has been recognized in the hydrometallurgical treatment of copper-bearing slimes; and a considerable amount of j work has been done at the Southwest Experiment Station of the U. S. Bureau of Mines in an effort to develop a percolation method of treating slimes. Experimental work on the copper-leaching problem was started by H. E. Keyes1, and later tests were made by J. D. Sullivan and A. P. Towne2. The Bureau of Mines work resulted in the development of a process by which slimes were moisture-agglomerated with sand and crushed ore, to form a permeable mass through which solution could be trickled without breaking clown the glomerules. The agglomeration trickle-leaching method was devel-oped on a small scale and finally tried out in a 12-ton vat. Successful results were obtained as long is the leach solution was added slowly, so that the agglomerated charge was never flooded. If the leach solu-tion flooded the charge, the glomerules broke down and, the charge became impervious. There are two important difficulties in the application of the agglom-eration trickle-leaching-method to the cyanide process for gold and silver ores:

Jan 1, 1937

By A. W. Schlechten, R. F. Doelling

Parkes' process crusts were vacuum distilled using a shortened Pidgeon retort. Zinc was effectively removed below 800°C and recovered as a zinc sheet easily stripped from the furnace liner. Lead dasdistillationazinc required about 950°C and the resulting lead condensate tillationtended to stick to the thin metal liner. Final purity of residue is limited only by nonvolatile metals such as copper. THE successful commercial application of vacuum distillation for the removal of zinc from lead, as described by W. T. Isbell,' raises the question of whether or not a similar method can be used for other metal separations. Preliminary laboratory experiments on the vacuum distillation of Parkes' crusts by one of the authors' gave such encouraging results that it was decided to make a series of tests with large scale equipment to determine the results that might be expected in plant operation. The pilot-plant test results are reported in this paper. The great advantages of vacuum dezincing are its simplicity, the relatively low temperature of operation, and the fact that the zinc is recovered in the metallic state ready for use again in the desilveriza-tion of lead bullion. These same advantages and others would be realized from the vacuum distillation of the zinc-lead-silver crusts made in the Parkes' process. Zinc readily will distill over at temperatures of 800" to 900 °C as contrasted with the 1200°C or more used in the Faber du Faur furnace. Furthermore, the recovery of zinc as metal is practically perfect since there is no loss by oxidation or fuming. If the vacuum distillation is continued and hastened by raising the temperature to around 1000°C, the lead will distill over at an appreciable rate and deposit in a warmer zone of the condenser. This lead will contain a small amount of silver, but it can be returned to the desilverizing kettles and there is not the chance of loss that there is in disposing of the rich litharge from cupelling. The lower temperatures required will mean a saving of fuel and less wear on the equipment. One further point is that the vacuum distillation could be run on a small scale practically continuously, so as to avoid the accumulation of large amounts of silver-rich material and the need of assembling a large crew for special cupellation runs. It should be pointed out here that the final purity of the silver residue will depend on the copper or iron content of the crusts, as these and other metals with low vapor pressure will not be eliminated. The idea of treating the silver-zinc-lead crusts from the desilverization of lead bullion by vacuum distillation is not a new one, but such experiments have not been reported, as far as can be determined. In 1912, T. Turner presented a paper3 before the Institute of Metals on the vacuum distillation of brass, and a member of the audience suggested that he try his method on Parkes' crusts. In 1935, W. J. Kroll, noted for his discovery of debismuthiz-ing lead by calcium additions, published a paper' on vacuum distillation of metals and pointed out possible applications in the lead industry. Principles of Separation The successful separation of two or more metals by distillation depends upon an appreciable difference in the effective vapor pressures of the metals in the alloy to be treated. The vapor pressures of the common metals have been determined with considerable accuracy; for example, at 800°C the vapor pressures of the individual metals which are of particular interest in this paper are about .as follows: Zn, 241 mm; Pb, 0.0553 mm; and Ag, 0.0000276 mm. Unfortunately,, data are not available on the activities of the components in the ternary system Zn-Pb-Ag, but it can be estimated that on the basis of the vapor pressures of the individual metals a good separation can be made by distillation. The preliminary laboratory tests previously mentioned' supported this assumption. The pilot-plant size vacuum distilling furnace is shown in Fig. 1. It consisted of an abbreviated Pidgeon retort, 5 ft long with an ID of 8 in., heated by six silicon carbide elements placed symmetrically

Jan 1, 1952

By F. L. Sizer

SOME old-time views which have recently come into my possession have inspired me to record that part of the early history of Leadville, Color- ado, with which I am familiar, the years 1878 to 1882, in the hope that others will add to what is here mentioned. My first appearance in Leadville was in June, 1878, immediately after graduation from the University of Michigan, and I found a congenial and lively crowd of young men, already there. The old log hotel, at the corner of Pine and State streets, housed some distinguished guests in the summer and fall of 1878. It was my good fortune there to make the acquaintance of James B. Grant, afterwards Governor of Colorado, in July of that year, when we were both glad of the accommodation afforded by cots in the second floor loft of the hostelry presided over by Herman Hibschle. Grant was then building his smelter and our associates were Eddy and James, August R. Meyer, and Berdell and Witherell. The Grand Hotel-Harris and Walsh, pro- prietors-was the first-class hotel of the place; but in a very few months there were many competitors.

Jan 1, 1924

By C. A. Siebert, G. Sandoz

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By G. Sandoz, C. A. Siebert

Oil quenching of steel, in good commercial practice, is carried out using a great deal of agitation in the quenching bath. Many of the tests reported in the literature represent the results obtained on steels quenched into still oil. Scott1 describes three stages of cooling in liquid quenching baths, namely: "State 'A'— Vapor Blanket Cooling—In this, the first stage, a thin stable vapor film surrounds the hot metal. Cooling is by conduction and radiation through the gaseous film and is therefore relatively slow. "Stage 'B'—Vapor Transport Cooling— Termination of the 'A' stage is marked by wetting of the metal surface. Vapor forms copiously in bubbles and is carried away by gravity and convection currents to condense in cooler surrounding liquid. This is the fastest stage of cooling. "Stage 'C'—Liquid Cooling—The 'B' stage ends as the surface temperature of the metal approaches the boiling point of the quenching liquid. Vapor no longer forms, so cooling is by conduction and convection and the temperature difference is greatly decreased. This mode of cooling is slower than that of the 'B' stage." Mechanical agitation of the quenching medium will accelerate all three stages of cooling. The greatest effect, however, will be noted on stage ' B' because the removal of the bubbles from the surface of the steel will not be entirely dependent upon gravity and natural convection currents. The method employed in this investigation for evaluating the oils was the end quench test. The various oils were substituted for water as the quenching liquid and hardness determinations were made at various distances from the quenched end. Most of the tests were run using a 3/8-in. orifice with a 21/2-in. stream height. However, to check the effect of other velocities two additional conditions were used, namely: (I) A 3/8-in. orifice and I-in. stream height, and (2) a 1/2-in. orifice and a 31/2-in. stream height. In all cases the samples were suspended so that the quenched end was 1/2-in. above the orifice. Some tests were run on an NE 8740, .3,312, and a 4340 steel. The results obtained on these steels confirmed those obtained on the NE 9450 and have therefore been Omitted from this paper. The test bars were machined from 1/8-in. stock to I-in. diam by 4 in. long.

Jan 1, 1949

By Nicholas J. Grant, A. W. Mullendore, Paul Predecki

The Duwez technique of splat cooling in which a molten droplet of metal is accelerated and made to impact on a cold, highly conducting substrate was investigated.- An apparatus for producing "splat" was constructed employing an explosive powder charge to accelerate the molten metal. Transport of the molten metal just prior to impact with the substrate was studied by means of high-speed photography. The molten particles are small spherical droplets from about 1 to 50 µ diameter. The average cooling rates for aluminum, silver, and a gold alloy splatted on nickel substrates at room temperature were determined experimentally and were found to vary from 18 to 5 x 10' C per sec. The heat-transfer coeficients for pure aluminum and pure silver splats cooled on nickel substrates at room temperature were found to be 2.7 to 6.8 and 13.6 to 54.2 cal per sec sq cm 'C (2 to 5 x 104 and 1 to 4 x 18 Btu per hr sq ft OF), respectively. Solidification rates in pure aluminum and silver splats were calculated. "SPLAT cooling" is a term describing a technique for extremely rapid freezing and cooling of molten metals and alloys to room temperature or below. The technique was developed by Duwez et al.' in 1960, and after refinement2 consisted in transferring a few tenths of a gram of molten metal to near sonic velocity to strike a suitably placed cold copper surface. Upon impact, the metal spread into a thin nonuniform film called a splat, about 10-4 cm thick. The splat particles produced in this manner were thin enough in some areas to be suitable for transmission electron microscopy, without further treatment, and, together with X-ray data, yielded a variety of structures which would be classified as follows: 1) supersaturated solid solutions (increase in solubility limit), 2) metastable crystalline stoichiometric and non-stoichiometric intermediate phases ( in Au-20.5 at. pct Si and in Au-14 at. pct Sb, respectively), 3) amorphous alloys, 4) retained high-temperature phases, 5) alloys having equilibrium phases present, but with unusual, markedly altered structures. The crystalline phases present in splats were usually extremely fine-grained and had low dislocation densities. Present interest in splat cooling centers around a study of the unusual structures produced by the technique, their contribution to alloy theory, and the possibility of the development of new or unusual properties. In addition, the technique is being examined for the production of bulk quantities of new high-strength alloys for low- and high-temperature use. Although a number of alloy systems have already been investigated by the technique, relatively little is known about the mechanism of splat formation and the physical conditions encountered by the metal during solidification and cooling. The purpose of this work was: 1) to determine the velocity, shape, and size of the molten metal droplets just prior to impact with the cold substrate; 2) to try to estimate or measure solidification rates, heat-transfer coefficients, and cooling rates in splats. EXPERIMENTAL TECHNIQUE Splatting Apparatus and Procedure. An apparatus similar to the type originated by Duwez et a1.,2 but employing an explosive charge to accelerate the molten metal, was used. A "Ramset" fastening tool (a gun normally used for driving studs into concrete, steel, and so forth) was mounted vertically above a resistance-heated graphite crucible as shown schematically in Fig. 1. A splat product was produced by melting a few tenths of a gram of metal at the position shown in Fig. 1, and then exploding a powder charge in the breach. The shock wave thus generated traveled down the barrel into the furnace, ejecting the molten metal through the 0.06-in.-diameter hole at the bottom of the crucible. The ejected metal was impacted on a high-conductivity metallic substrate where it formed a splat. High-Speed silhouette Photography. In order to investigate the size and shape of the ejected, molten metal just prior to impact with the cold substrate, high-speed silhouette photographs were taken, and are shown in Figs. 2 and 3. These photographs were obtained with the aid of an Edger-ton, Germeshausen, and Grier microflash unit and a submicrosecond flash drive equipped with a variable time delay. Two types of triggers were

Jan 1, 1965

By H. M. Chance

In recent years an important function of the mining engineer has been the appraisal of the value of mining-properties required by those planning consolidations of a number of' individual operations. In no field of productive industry have the economic results attainable by consolidation been more clearly shown than in the mining-regions of the United States. In many important mining-centers unification of ownership of the most valuable properties has already partially or completely been attained, and, in other districts, projected absorptions and consolidations await only favorable financial conditions for their consummation. The iron-ore districts of the Lake Superior region, the coal-mines of Colorado, of Wyoming and of Utah, the anthracite mines of Pennsylvania, the Connellsville coking-coal mines, and large areas of bituminous coal-land in Pennsylvania, in Ohio, in the Indian Territory and in other portions of the United States, are now largely controlled by a few corporations operating on a large scale, or by a number of corporations working in harmony because of an affiliation and interleaving of interests. The tact of keen financiers and the diplomacy of men of great administrative ability are the chief operative forces in conceiving and accomplishing such consolidations, but in formulating and maturing them, the services of the mining engineer are often required to supply the facts upon which they must be based. For this purpose the expert is expected to furnish full and complete reports covering the quantity of ore, coal or other mineral available, its value per ton, cost of mining and treatment, etc. In reporting upon gold-, silver-, lead-, zinc-, copper- or iron-

Jan 1, 1905

By Robert Mehl

THE system cadmium-mercury has attracted much attention, chiefly because of its importance in the study of electrochemical standard cells. The constitutional diagram, as it is accepted today, is essentially that FIG. 1.-BIJL'S DIAGRAM FOR CADMIUM-MERCURY ALLOYS. developed by Bijl1 (Fig. 1), though there has been a great amount of work done on the system by other workers.2 A year ago the senior author published a paper on the crystal structure of the system, in which were described determinations of crystal structure

Jan 1, 1929

By William D. Klopp, Joseph R. Stephens

ThE phenomenon of high ductility associated with a phase transformation, termed super plasticity, has been reported for a number of alloy systems. Abnormally high ductility has been observed during tensile testing of cast eutectic alloys of Pb-Sn and Mg-cu.1 Brasses of Cu-37 at. pct Zn and Cu-40 at. pct Zn elongate up to 180 pct when tested near their transformation temperature.' Enhanced ductility was also observed in Cu-47 at. pct Zn tested near the order-disorder transformation temperature. The most remarkable super-plastic effect reported to date is for the eutectoid alloy A1-60 at. pct Zn, where elongations up to 1000 pct have been reported.3 underwood4 has recently summarized the conditions that normally accompany the superplastic effect which are: 1) a phase transformation or allotropic change or order-disorder transformation; 2) an externally applied stress; 3) presence of an interface between two phases; and 4) a metastable structural condition. In addition, higher ductility is observed when the specimen is tested at slow deformation rates rather than under impact. The purpose of this note is to present evidence of the superplastic effect in a Cr-30 at. pct Co alloy. In addition, low-temperature bend ductility data are given for the alloy in the quenched, metastable, single-phased condition and in the slow-cooled, two-phased, near-equilibrium condition. Sixty-gram alloy ingots were prepared by noncon-sumable arc melting of iodide chromium and electron-beam-melted cobalt. These were cast into rectangular ingots and fabricated to 0.035-in. sheet by rolling at 2300°F. Attempts to roll at slightly lower temperatures invariably resulted in severe cracking, apparently due to presence of the brittle a phase below the transformation temperature of 2230°F. Tensile specimens with a 0.25 by 1.0 in. reduced section were cut from the sheet by electrical discharge machining. The specimens were heated at 2400°F for 1/2 hr to obtain a recrystallized, bcc, single-phased structure. Temperature of the specimens was subsequently raised or lowered to the desired test temperature and held for 10 min prior to testing at a crosshead speed of 0.01 in. per min. Fig. 1 shows the chromium-rich side of the Cr-Co phase diagram.6 The alloy composition investigated is near the point of maximum solubility of cobalt in chromium, and the alloy is two-phased when in equilibrium at temperatures below 2230°F. The results of tensile tests conducted at temperatures indicated by X's in Fig. 1 are summarized in Figs. 2, 3, and 4. Tensile elongations shown in Fig. 2 increase from 11 pct at 1900°F to a maximum of 160 pct at 2250°F. The elongation then decreases to 44 pct as the test temperature is further increased to 2600°F. The proximity of the temperature of highest elongation and the solvus temperature suggests that a superplastic effect is present in Cr + 30 at. pct Co similar to that observed for other alloys that show anomalous ductility. The variation of upper yield stress with temperature is shown in Fig. 3. A small peak in yield stress occurs at 2250"F, coincident with the maximum in

Jan 1, 1967

By J. Nutting, J. W. Cahn

WITH the development of thin film techniques for the direct examination of metals in the electron microscope some new problems in quantitative metallography have become apparent. In order to obtain certain contrast effects in the electron optical image when examining thin films from alloys containing dispersed phases, it is essential to use films of a thickness at least two or three times greater than that of the mean particle diameter of the dispersed phase. From micrographs of such specimens it may be desired to obtain the volume fraction of the dispersed phase and the number of particles of the phase in a unit volume of the matrix. Under these conditions the particles sectioned by

Jan 1, 1960

By A. V. Henry

THE kaolins of the southeastern United States were known to civiliza-tion as early as the latter part of the eighteenth century-and yet the Fig. 1.-KAOLIN PRODUCTION AND IMPORTS. commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported.

Jan 1, 1937

By George J. Simchuk

Selection of an applicable stripping method and the subsequent determination of appropriate sizes of selected equipment are discussed. The case in point is Utah International, Inc.'s Goonyella mine located in central Queensland, Australia. A detailed study of the various types of stripping methods now practiced throughout the world led to the conclusion that large draglines would be the logical choice for Goonyella. The optimal size of dragline was then determined by first designing a series of cut diagrams using an array of machine and pit geometries followed by a cost comparison of the various sizes of machines, in terms of their effective spoil radius. A dragline with a 51-cu-yd bucket was determined to be of optimum size. Further calculations, incorporating total overburden moved from both the highwall and spoil sides, required that four drag lines, two equipped with 40-cy-yd buckets and two with 54-cu-yd buckets, be used to satisfy the stripping requirements at Goonyella.

Jan 1, 1973

By W. I. Duvall, D. E. Stephenson. Discussion by R. G. K. Morrison

R.G.K. Morrison (Chairman, Dept. of Mining Engineering and Applied Geophysics, McGill University, Montreal, Que. Canada) - The authors have introduced a subject, the intensive study of which has awaited scientific developments. These are now such as to justify a thorough review of our thinking on the causes and control of rockbursts. The formulae developed in the paper, the comparison between rockbursts and earthquakes in figure 1 and the energy data relating to explosives serve as an effective foundation. In the paper this writer is quoted as suggesting that energy of the order of 10 x 10 11 ft. lb. may have been released in some of the heaviest rockbursts in the Kolar Gold Field. He now hastens to add that such an estimate has no scientific validity. It arises only from a casual comparison of surface and underground effects of the medium heavy bursts, referred to in the paper and estimated by Jones at 3.0 x 1010 ft.lbs., with those of obviously greater magnitude. In any case, we have the estimate by Jones above, that by a team of seismologists 1 on the Witwatersrand of 10 x 1010 ft.lbs., that by Coates of 3.8 x 10" ft.lbs., also referred to in the paper, that by Blan-chard2 for the catastrophic rockburst at Springhill, N.S., of only 7.4 X 107 ft. lbs., and finally the range covered by Cook, referred to in the paper. It is probable also that data for the heavy rockburst at Merkers3 in the WERRA potash area of Germany are available as it was recorded on seismographs from Moscow to Spain. It is the writer's impression that some standardization is present in the estimates above for 10 x 10 10, 3.8 x 1010 and 7.4 x 107 ft.lbs., respectively. The latter, for Springhill, represents a relatively low order of magnitude. It is obvious that any energy estimate must be related to the local geometry of openings at the time of the event. It is also obvious that any explanation of the causes of rockburst must be capable of providing a wide range of energy. However, we must remember that the energy release is an effect indicating magnitude. The cause lies with the mechanism initiating the primary failure, generating the seismic activity, to which much of the damage is probably due.

Jan 1, 1967

By J. M. Tobin, L. H. Cadoff, L. M. Adelsberg

The reaction between liquid zirconium and graphite at temperatures above 2000 °C has been investigated. The reaction products were found to be carbon-saturated zirconium metal and ZrC which formed between the graphite and the metal. Parabolic growth behavior was observed for the ZrC Phase at all temperatures of this investigation. The parabolic growth constant at temperatures between 2000° and 2860°C was measured to be 1.83 exp 84,300/RT) sq cm per sec. The reaclion mechanism was proposed to be the rapid carbon saturation of the liquid metal and the formation of ZrC at the metal-carbide interface with diffusion of carbon through the ZrC, the "rate - determining step" of the reaction. The concentration-independent diffusion coefficient of carbon in ZrC, (DZrC), was expressed as 0.95 exp? 78,700/RT) sq cm per sec. This value mas calculated using the temperature-invariant ZrC phase fields proposed in the literature. The [ZrQiq)] — [ZYQiq) + ZrC] phase boundary over the temperature range 2000° to 2800°C was determined and the ZrC + C eutectic temperature was found to be 2890° ± 50°C. ThE Group IV and VB transition-metal refractory carbides are of interest because of their high melting points, high temperature strength properties, and relative inertness in certain corrosive environments. The present-day understanding of these materials, however, is limited by the general unavailability of accurate and reliable physical and chemical property data. This is due primarily to the difficulties associated with the preparation of suitable, high-density, high-purity carbide samples, and the achievement and control of uniform high-temperature environments. Accurate measurement of temperature is also an important factor limiting the reliability of reported data. The Zr-C reaction was selected for investigation because of the high melting point (>34000C) and favorable nuclear properties of the reaction product, ZrC. The direct reaction method afforded an opportunity to obtain kinetic data on the fully dense carbide. In this paper, layer-growth techniques were used to estimate the diffusivity of carbon in ZrC and to investigate the phase equilibria in the Zr-C system at temperatures above 2000°C. EXPERIMENTAL PROCEDURES AND DATA Crystal bar zirconium (99.9 pct Zr), purchased from the Nuclear Materials and Engineering Corp., and ZTA graphite (99.9+ pct) were used in this study. The analyses of the materials are listed in Table I. A schematic of the high-temperature carburization apparatus is shown in Fig. 1. The sample was a zirconium metal charge in a 1/2 -in.-ID graphite crucible which was capped with a tightly fitting graphite stern. The crucible and stem were designed to closely approximate black-body conditions. The graphite crucible was packed in lampblack (outgassed 1 hr at 2100°C) which provided insulation and thermal stability to the system. The inert atmosphere was maintained by a constant flow of high-purity argon or helium gas. The nozzle-diffuser section on the top flange was sufficient to prevent back-diffusion of air into the system. Chemical analysis of the carburized samples revealed oxygen and nitrogen concentrations of less than 44 and 20 ppm, respectively. The sample was heated by induction with a Westing-house 5 kw-450 kc power source. Temperature was measured with a Milletron two-color pyrometer which was sighted into the crucible by reflection from an overhead front surface mirror. Optical losses due to glass absorption and light reflection at air-glass interfaces were minimized by the employment of the dynamic-gas seal. It was found that no correction was required for the front surface reflector. The pyrometer was calibrated periodically against a U.S. Bureau of Standards tungsten ribbon secondary standard. Temperatures inside the crucible were also calibrated against the Zr-ZrC eutectic (1850°C)1 and the Nb-Nb2C eutectic (2335°C)2,3 temperatures and agreed to within ±10°C of these values. The temperature was controlled by manually adjusting the power input; variations of

Jan 1, 1967

By C. D. Ramsden

DURING the war years of 1941 to 1945, maintenance of mine locomotives and other mine equipment took the form of rebuilding rather than of renewing. Pur¬chase of new parts became increasingly difficult and mine operators found it necessary to maintain equipment by sal¬vaging old parts. Mine-locomotive wheels, although not representing a high cost per pound of material, contain a con¬siderable amount of steel and without rebuilding would have to be scrapped long before even a moderate percentage of the steel in the wheel is actually consumed. Many mine operators have been re¬building locomotive wheels for several years with automatic open arc-welding equipment. In 1927, the Pittsburgh Coal Co. started such a program, using a single Westinghouse automatic welding head. Since that time, many refinements have been added, until in 1944 the setup was operating very efficiently. A desire to increase wheel life and to hold down rising costs led the company in 1944 to investigate the possibilities of the under¬flux arc-welding process for wheel rebuild¬ing, although at that time, little or no work had been done on multiple pass or "build-up" welding with the underflux arc. Work with this process had been confined largely to welding together flat plates in a "down hand" position. Possibilities for savings were intensified by the fact that the company has 300 locomotives in operation, using actively or as spares 1200 sets of wheels. During 1942 and 1943, about 500 sets of wheels were sent each year to the company's maintenance shop at Library, Pa., for rebuilding. Based on having 800 sets in service (many of the company's heavy locomotives have three- sets of trucks), the average life of a set of wheels was approximately 19 months. Anything that could be done to increase wheel life promised sizable annual savings. OPEN ARC WELDING With the open arc process, a set of wheels could be rebuilt for about 40 pct of the cost of new wheels. Underflux arc welding gave promise of greatly increased welding speeds, more homogeneous, dense deposits and the chance for use of a wider range in welding-wire compositions. Against this was ranged the higher cost of materials and the cost of developing the process from the theory to a practical reality. Since 1927, when a single open arc head was placed in operation, fixed welding procedures had been gradually developed, a positioner for handling a set of wheels was built, and a second head was placed in operation in order to weld two wheels simultaneously. The fixture, or posi¬tioner, which was built to position and turn the wheels under the two welding heads, included a motor drive, controlled by a rheostat, which rotated the wheels through a double set of speed reducers and a removable jaw coupling attached to one end of the axle of the wheel truck.

Jan 1, 1946

While coal was mined in New Mexico in 1860, production was on a small scale during the period considered here, and Table 77 contains all the data found. [ ]

Jan 1, 1942

[PAGE PREFACE. A. B. PARSONS 3 OFFICERS AND DIRECTORS 7 STANDING AND SPECIAL COMMITTEES 8 PROCEEDINGS OF 1935 MEETINGS 10 NEW YORK, FEBRUARY 10 CHICAGO, OCTOBER 14 SAN FRANCISCO, OCTOBER 14 HOUSTON, OCTOBER 15 ST. LOUIS, OCTOBER 15 ABSTRACTS OF PAPERS PUBLISHED IN 1935 17 TECHNICAL PUBLICATIONS AND CONTRIBUTIONS, 1935 64 INDEX OF 1935 PUBLICATIONS 71]

Jan 1, 1936

By Hallan N. Marsh

The subject of mud sounds so simple, uninteresting and unimportant that it has failed to receive the attention that it deserves, at least as applied to the drilling of oil wells. As a matter of fact, it is one of the most complicated, technical, important and interesting subjects in connection with rotary drilling. In 1923, R. E. Colloml said "It should be possible to establish certain physical standards for mud fluid," but while considerable work has probably been done on the subject before and since that time, and numerous articles have been written, the progress of general knowledge of the subject and the application of better practices have not kept pace with other developments in rotary drilling, and physical standards cannot be considered as established. Mud is apt to be thought of as an accessible and cheap material, but its cost is likely to be an important factor in the total cost of drilling a well. Some wells "make" most of their own mud out of the formations drilled, but in most cases a great deal of mud-making material has to be supplied from more or less distant sources. Expenditures for mud materials by one California company totaled practically one-quarter million dollars during 1929 and averaged about $13 per rig per drilling day, or about $2000 per well. Under unfavorable conditions, mud cost may reach many times this figure. Parker2 says that in the Hobbs, N. M., field "as much as $75,000 has been spent on one well alone for mud and mud-weighting compounds."' Presumably this is an exceptional case. Unit cost of mud fluid will range from 10 c. per barrel, where suitable material is close at hand, to $1 where crude material is available at moderate price but must be hauled long distances, and on up to as much as $11 per barrel where high gas pressure requires the use of special processed weighting material. The cost of mud pales into insignificance, however, when the results of using improper mud are considered. Blow-outs and lost circulation are obviously the result of inadequate mud. Stuck drill pipe, whether or not twisted off, in many if not most cases probably is caused by cuttings settling out of the mud or the mud itself precipitating. Recent experi-

Jan 1, 1931