Search Documents

J. D. Fast and J. L. Meijering (Philips Research Laboratories, N. V. Philips' Gloeilampenfabrieken, Eindhoven, Netherlands)— After the departure of our friend Dijkstra to the United States, investigations on the effect of alloying elements on the behavior of nitrogen in a iron were continued in Eindhoven. We too found internal friction curves with two separate peaks for iron containing nitrogen in addition to 0.5 atomic pct V or 0.5 atomic pct Mo. Our first publication on these investigations" appeared almost simultaneously with the paper now under discussion. At first sight our experimental results seem to be in harmony with their conclusions, but a closer examination reveals that in the case of the Fe-V-N alloy the abnormal peak is not controlled by one time of relaxation only. Whereas iron containing 0.5 atomic pct Mn or Mo absorbs an amount of nitrogen of about the same magnitude as that absorbed by pure iron under identical conditions, iron containing vanadium absorbs in addition one nitrogen atom for every vanadium atom. This last amount, far exceeding the first amount in the case under consideration, combines chemically with the vanadium and causes no internal friction. The "free" nitrogen in the vanadium alloy gives rise not only to a damping peak corresponding to that in pure iron but— due to the presence of VN particles in the metal—also to the abnormal peak at higher temperatures. The VN particles create interstitial sites around themselves where the free nitrogen atoms are bound much tighter than in the normal interstices. These abnormal interstices, therefore, will capture free nitrogen atoms rapidly, whereupon these give rise to the abnormal damping. The binding energy in the abnormal interstices is not the same for all, and with coarsening of the VN precipitate the distribution of these energies is displaced toward the side of stronger binding. This is deduced from a shift of the summit of the second peak toward higher temperatures (from 80" to 88°C in our experiments) caused by prolonged heating at 950°C. From the intermediate state where they cause the abnormal damping, the nitrogen atoms pass over rather rapidly into the fully precipitated state (iron

Jan 1, 1954

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By Cyril Stanley Smith

Somewhat over ten years ago the author described studies1'2 on the constitution of the copper-silicon system. The copper-rich portion of this diagram is shown in Fig. 1. The experimental points freely dotted about the diagram seemed to justify an otherwise unconvincing diagram and for several years the curious reverse bend in the alpha-phase boundary was accepted as substantially correct, even by later investigators3 of the system who introduced changes in the high-silicon phases. The binary diagram has been used as a base for several ternary systems5-9 without any suggested changes. Voce10 suspected the existence of another phase from his study of the cast alloys in the copper-manganese-silicon system, but evidently hesitated to extrapolate this to the binary diagram, particularly in view of the too ingenious explanation that was advanced1' to account for the pools of constituent clearly visible in castings; namely, that they were secondary alpha of twinned orientation deposited from beta. Von Schwarz,12 in 1932, called attention to the fact that this micro-constituent in copper-silicon alloy castings was anisotropic under polarized light and asserted that a new phase, not cubic, should be placed in the diagram .adjacent to alpha. Sautner,l3 on the basis of investigations with the polarizing microscope and with X-rays, introduced this phase into the diagram at about 6 per cent Si. The relevant part of his diagram is shown in Fig. 2. Sautner called the new phase beta, renaming the old beta phase zeta. To avoid confusion, in redrawing Fig. 2 the phases have been renamed in accordance with the terminology adopted in the present paper, in which the new phase is called kappa and the other phases retain the designation given them by Arrhenius and Westgren.4 The thermodynamic impossibility of Sautner's diagram and the paucity of experimental data left the exact location of the new phase field most uncertain, although his work proved beyond doubt that an additional noncubic phase exists. Because of the industrial importance

Jan 1, 1940

By T. Toda, R. Maddin

A study has been made of the microstructure and mechanical properties of splat-cooled aluminum-base gold alloys with gold concentration from 0.25 to 5.0 wt pct. These alloys have been quenched from the liquid state by a torsion-catapult technique, which has made it possible to pepare specimens suitable for mechanical property measwements. From the electron micrographs it has been shown that the solid solubility of gold in aluminum can be extended to 2.5 wt pct (0.35 at. pct) by splat-cooling, while the maximum equilibrium solubility is known to be less than 0.3 wt pct (0.04 at. pct). The very fine grain size (several tenths of a micron), the extended solid solubility, and the fine dispersion of a second phase (AuAl2) contribute concurrently to a substantial strengthening effect. In Al-5 wt pct Au splat-cooled specimens of less than 50 thickness, the yield strength is 17 kg per sq mm or 6 times as large as the strength of bulk specimens. For the Al-1.0 to 2.5 wt pct Au solid solution obtained by splat-cooling, the yield strength reaches 7.5 kg per sq mm after an aging treatment (for 10 hr at 200°C), while it is 3.7 kg per sq mm for the corresponding bulk specimens. A great deal of research has been done in recent years on the structure and the properties of metals and alloys rapidly quenched from the liquid state.' The term "splat-cool" has been used with the meaning of a rapid quenching from the liquid state., The splat-cooling techniques have produced large numbers of new structures, which are expressed in terms of metastable phases,3 concentrated solid solutions,4 amorphous phases,5'6 new phases,7 and so forth. Nearly all previous studies have concentrated on the physical properties; i.e., crystallography, structure, electrical resistivity, magnetism, and so forth, of the splat-cooled metals and alloys. The mechanical strength of splat-cooled metals and alloys has hardly been investigated except for some recent work by MOSS' on A1-V alloys. The principle common to all experimental techniques developed to obtain very rapid quenching rates is based on the heat transfer by conduction. Liquid must be in good thermal contact with a substrate of high heat conductivity. Both of the published devices known as the "gun" and the "piston and anvil" techniques suffer from certain shortcomings. For example, the specimen obtained by the gun technique is very small and flaky, and hence inadequate for mechanical properties measurements. On the other hand if the material is forced to yield a continuous speci- men by the piston and anvil technique, it is probable that some plastic deformation occurs during the quench. A novel method for rapid quenching of a liquid metal or alloy, the "torsion-catapult", has been devised by Roberge and Herman9 at the University of Pennsylvania. In the apparatus the melt is thrown out of a curved furnace by a catapult and impinges on a copper substrate. The apparatus has the advantage of producing a continuous foil which is relatively large in size and of a quality suitable for the measurements of mechanical properties. The quenching rate is estimated to be of the order of l05 to l06 ºC per sec, (comparable to rates achieved by the piston and anvil technique). In selecting an alloy to be studied we were made aware of the fact that gold was believed to be "insoluble" in in and consequently age hardening in the A1-Au system appeared to be interesting. Quite recently Heirnendahl13-15 revealed that the solid solubility, as determined by transmission electron microscopy, was 0.3 wt pct Au at 640°C and 0.25 wt pct Au at 600°C, decreasing with decreasing temperature. In an A1-0.2 pct Au alloy after quenching from a solution treating temperature of 600°C the yield stress was 2 kg per sq mm, and it increased up to 6 kg per sq mm after aging for 1 to 10 hr at 200°C. The precipitation occurred in the form of platelike particles mainly on (100) matrix planes. The intermediate phase n', the equilibrium phase n (AuAl2), and lattice relationships between both precipitates and the matrix were also investigated by electron microscopy. One of the purposes of the present research is to determine whether or not the solid solubility in this system, in which gold has a very small solubility in

Jan 1, 1970

By J. J. Arps

This paper is a study of the effect of temperature on the electrical resistivity of sodium chloride solutions based on the published resistivity and density data in the International Critical Tables. This temperature effect is of considerable importance in quantitative interpretation of electric logs, where it is frequently necessary to correct mud resistivities measured under surface conditions to temperatures existing at the bottom of the bore hole. An empirical approximation formula was developed for this conversion which has proved to be very useful and seems to provide results well within the range of accuracy of the data involved. This approximation formula states: sistivities of sodium chloride solutions at temperatures of t and t degrees Fahrenheit, respectively. INTRODUCTION Research by various investigators during the past 20 years has clarified the physical principles of the phenomena which cause the natural or spontaneous electric potential in rotary drilled bore holes. The basic relationship which is most commonly used reads: in which the SP deflection, as measured from the shale base line, is expressed in millivolts. K is a constant, which appears to vary between 50 and 110; the low value applying to shaly sands, whereas the higher values are more common in carbonate rocks. A good average value for K = 70. for which value there is considerable theoretical justification." In order to calculate the resistivity of the connate water R and to estimate its "equivalent salinity" (as NaCl) from an electric log by means of this SP relationship from a knowledge of the static self potential and of the resistiv- ity of the mud filtrate R it is necessary to first correct the resistivity of the mud filtrate measured under surface conditions to the resistivity of this same mud filtrate in the well bore at a different temperature. In order to make this temperature conversion for the mud filtrate the variation of the electrical resistivity of sodium chloride solutions with temperature is commonly used. Since some discrepancies were found in the charts ordinarily used for this purpose, it was felt desirable to make a new study of this relationship based on the published measurement data. Because of the fundamental nature of these relationships and as an aid to other workers in this field, an attempt has been made in this study to show every step in the calculations. CONDUCTIVITY VS MOL CONCENTRATION The most complete published reference on the temperature relationship of sodium chloride solutions of different concentrations is provided in the International Critical Tables.' The basic measurement data on the electrical conductivity of aqueous sodium chloride solutions, at different temperatures, as given in these tables, are reproduced in Table 1. The electrical conductivity values in this Table 1 are expressed as 10' times the specific conductivity k in ohm-'cm'l per unit of concentration in milligram mols per liter of solution C, or: RESISTIVITY VS MOL CONCENTRATION These conductivity values from Table 1 were first converted to the corresponding electrical resistivity values (R) , expressed in ohm-meters, as is conven-

Jan 1, 1953

By H. Rush Spedden

Antoine M. Gaudin was a vigorously creative man and throughout his career an internationally respected leader of his chosen profession of mineral engineering. To his professional colleagues and clients and to his former students he was both "Professor Gaudin," their wise, inspiring, and enthusiastic teacher, and "Tony," their, warm and beloved personal friend. Thus, his teachings and his unique inquisitive-creative approach to problems live on and grow in the accomplishments of his students. Antoine Gaudin was born at the turn of the century in Smyrna, Turkey, where his father was general manager of a French-owned railroad. It was there that he spent his earliest years, literally in the shadow of classic marbles from diggings at the site of Aphrodesias, which his father had rediscovered. From this, Tony developed an appreciation of the arts. He eventually surrounded himself with art treasures; he reveled in the beauties of nature, and he cherished his choice collection of rhododendron and azaleas. His artistic traits led him to take up painting when his daughter, Elinor, sought his help in blending her tints for a water color. In typical fashion he was not satisfied until he had become adept with pastels in capturing the muted tones of distant landscapes and the technical properties of light and color. Unfortunately not many paintings were produced. His paternal grandfather was Marc-Antoine Gaudin, for many years secretary of the Academie des Sciences in Paris, and a well known chemist and mineralogist whose primary interests included the synthesis of precious stones. In an autobiographical sketch written in 1939, Dr. Gaudin recalled: "As a child I saw many of the original synthetic sapphires and rubies which my father had inherited. This, coupled with my father's avocation of mining ventures and archaeology, early decided that I would become connected with the mineral industry." One can speculate that the archeological activities of his father, the mineral systhesis experiments of his grandfather, and his own early studies of mineralogy and geology formed a base from which his special talents as an experimentalist were to develop. Laboratory research under Professor Gaudin's personal guidance was often an intensive, fast-moving, and exciting experience--especially to a new graduate student. First of all, Professor Gaudin was a highly skilled observer with seem-

Jan 1, 1976

By Francis Lucas

A microscope objective of given numerical aperture, whew used with light of given wave length, has some fixed limit of resolution. This may be expressed as potential resolving ability-the ability to resolve is inherent in the lens but whether this limit is achieved in practice is quite another matter. Nearly 50 years ago Abbe evolved theoretical considerations which indicated that the ability of a lens to resolve detail is directly proportional to twice the numerical aperture of the objective and inversely proportional to the wave length of the light used. It is true, unquestionably, that as the numerical aperture of the objective is increased the potential resolving ability of the lens is increased and likewise whew the wave length of the light used is decreased, the degree of resolution is increased. Whether Abbe's formula expresses the exact relationship is not a matter of great concern. It suffices to know that to improve resolution, other things being equal, two avenues of approach are available. Either the numerical aperture of the objective may be increased or the wave length of the light decreased. With the apochromatic system it is possible to employ successfully wave lengths from 400 to 500, µµ and still secure reasonably short exposures. The present limit for numerical aperture is 1.40 N. A. although objectives of 1.65 N. A. are wow an experimental possibility for metallurgical work. Thus certain well defined limits are set for those who work within the range of the visible spectrum. In order to take advantage of the increase in resolving power which accompanies a decrease in the wave length of light employed, Dr. A. Köhler and Dr. M. Vow Rohr of the Zeiss Scientific Staff developed the "monochromats." These are quartz objectives corrected for the single wave length 275 µµ which lies in the ultra-violet region of the spectrum. They also developed a series of quartz oculars and a complete photo-micrographic equipment with which to use the quartz optics. Quartz must be used for the optical parts because glass absorbs ultra-violet light almost completely. Thus there was made available about 20 years

Jan 6, 1926

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By F. W. Sperr

The byproduct coke oven is the most important artificial source of fuels for metals melting. Its products are solid, liquid, and gaseous in form. The amount of coke and primary byproducts obtained per ton of coal varies with the nature of the coal. The following represents the results obtained in many plants: Metallurgical coke (over 3/4 in.).............................. 69 per cent. of coal Domestic coke (1/2 to 3/4 in.)................................ 2 per cent. of coal Breeze (under 1/2 in.)...................................... 4 per cent. of coal Surplus gas, cubic feet per net ton........................... 6600 Gas for heating ovens, cubic feet per net tor i................. 4400 Tar, gallons per net ton.................................... 9 Ammonium sulfate, pounds per net ton....................... 25 Benzols, gallolls per net ton................................. 4 All of these products, except ammonium sulfate, have important fuel value. Part or all of the metallurgical coke may be crushed or screened to furnish additional domestic coke. If producer gas is used, there will be a surplus of 11,000 cu. ft. of coke-oven gas per net ton of coal. The use of coke in the metallurgical industries has been retarded by the mental attitude of writers who disregard the dependence of coke quality on the conditions of its manufacture. Terms like "byproduct coke," ('beehive coke," "48-hour coke," and "72-hour coke" are only generally descriptive and tell nothing of the coke quality. For example, one writeri stated that in brass-foundry practice, Connellsville coke is considered rnuch superior to byproduct coke on account of the high sulfur content of the latter. Another2 says, "At equal prices for hard Connellsville coke and for byproduct coke at the foundry door, the hard coke is unquestionably cheaper. It will melt more metal per ton than the byproduct coke and requires less labor, as the byproduct coke is less dense and burns faster, thus requiring more frequent firing." A little study of the conditions under which coke is manufactured will show the error in making general statements like these. The percentage of sulfur in coke depends largely on that in the original coal, and byproduct coke from a

Jan 1, 1921

By J. Jolly

THIS short note on the probable character of the organic sulfur compounds in coal can do no more than indicate lines of research. We have no new experimental work to describe, nothing comparable in value with the careful studies of American coals by Powell and Parr1 and Yancey and Frazer.2 A study of the manner in which sulfur compounds exist in British coals (and their behavior on heat treatment) is rendered increasingly necessary by the fact that the British reserves of good coking coals of reasonably low sulfur content are fast being depleted. We believe that it is essentially by a study of the modes of formation, occurrence, and decomposition of the various types of inorganic and organic sulfur compounds in coal that it will be possible, with hope of success, to attack the problem of purifying coals, otherwise eminently suitable for coking, from these objectionable ingredients. Sulfur, so far as is at present known, does not normally occur in the free state in the coal conglomerate, but is chiefly distributed, irregularly, in three forms: 1. As primary constituents of the coal conglomerate, organic in nature and probably associated with those molecular complexes that have resulted from the degradation of the proteins of the plant tissues responsible for the formation of the coal mass. These constituents can be classed as "organic sulfur." 2. As metallic sulfides, e.g., iron pyrites. 3. As metallic sulfates, e.g., calcium sulfate and ferrous sulfate. (The occurrence of these compounds varies with the occurrence and degree of degradation of class 2.)

Jan 3, 1925

By AIME AIME

A JOINT meeting of the Canadian Institute of Mining and Metallurgy and the American Institute of Mining and Metallurgical Engineers was held at Spokane, Wash., and Cranbrook and Kimberley, B. C., on Oct. 13 to 16, 1926, with a total attendance at one or another or all of the meetings of about 300 members, ladies and guests. At the opening meeting, on Oct. 13, in the Davenport Hotel, Spokane, about 175 were present. The morning was occupied with addresses of welcome by M. H. Sullivan for the Columbia Section, who called on Mayor Charles A. Fleming, President John F. Davies for the Chamber of Commerce, and E. R. Hannibal, president of the Associated Engineers, each of whom heartily welcomed the visitors. Philip N. Moore, former president, and special representative of President Samuel A. Taylor, replied for the A.I.M.E., and Lewis Stockett, president, and Charles A. Banks, chairman, British Columbia Division, Canadian Institute of Mining and Metallurgy, and Henry M. Parks for the visiting A.I.M.E. sections, made appropriate responses on behalf of those they represented. The members and ladies had luncheon with the Associated Engineers. Philip N. Moore addressed the assembly on "The Opportunity of the Engineer"; an excerpt from his address appears on another page. At the afternoon meeting, with Lewis Stockett in the chair, Frank M. Smith was asked to make a brief statement of the proceedings of the Silver Producers Association in Denver. Supplementing his talk by placing a well-prepared statement on "Silver and the Plan of the Royal Commission on Indian Currency and Finance" in the hands of those present, he narrated what had been undertaken by the Silver Producers Association and what they hoped to accomplish.

Jan 1, 1926

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By F. D. Mahone

Much crude oil, as produced from the well, carries varying amounts of water, which may be present as free water in globules sufficiently large to settle out, in time, if the fluid is allowed to stand, or as an emulsion formed by myriads of minute water particles, each surrounded and entrapped by a film of oil through which it cannot break under the action of gravity alone. Such an emulsified mixture of oil and water is commonly termed "cut oil." When such an emulsion is subjected, under proper conditions, to the influence of a high-potential alternating-current field, the minute water particles rupture the enveloping oil films and coalesce into larger water droplets this procedure continuing until all the water is freed into drops of such size that they readily settle out. This action has been photographed by the micro-moving-picture camera; under the microscope, the breaking-up of the emulsion, as described, is seen to be accomplished in a few seconds. The low power requirements of the process, from records of commercial plants, substantiate the theory that the action is that of a multitude of electrical condensers in series, rather than that of a number of conducting paths. The minute water particles serve as the metallic elements, or plates, of the condensers and the separating oil acts as the dielectric. Such surface charges as the particles may have are removed, and the intervening oil is broken, probably electrically by the voltage and mechanically by the attractive force between adjacent oppositely electrified particles. The principle of breaking up an emulsion under the influence of an alternating electric field was discovered by F. G. Cottrell and Buckner Speed, through experiments conducted, at the University of California, which resulted in a plant being installed on the property of the Lucile Oil Co. in the Coalinga field, California, early in 1909. This plant was able to reduce 14-per cent. emulsion to less than Pper cent. with commercial success. Standard Cottrell Apparatus The present standard Cottrell apparatus consists essentially of the electric treater and a settling or trap tank. The treater is a galvanized-iron tank approximately 3 ft. in diameter and 10 ft. high, which con-

Jan 1, 1924

By F. L. Ruhlman, Max C. Eastman

The termination of the recent war marked a major changc in the oil-field operations at. Elk Hills. Production was greatly curtailed, various experimental production projects were started, and a long-range exploratory program was inaugurated. Production was reduced from the wartime peak of 65,000 bbl per day to the current rate of about 8ooo bbl per day in order to maintain an available source of crude that can be drawn upon during a national emergency. The existing production rate is deemed essential to carry on the experimental production projects. These projects are being conducted to determine the best methods and means of maintaining the Reserve, shut in, but in a state of readiness to produce the maximum quantity of oil in the most expeditious manner. Projects now being investigated include: (I) protection of surface equipmerit; (2) repair of wells that might damage the reservoir; (3) gas injection; (4) water eneroachment, (5) gravity drainage. An exploratory program is being carried on to determine the amount of recoverable oil in the unexplored portions of the Reserve. The Shallow-zone exploration is practically completed, but owing to the complexity of the Stevens structure and the magnitude of the oil discoveries in the Stevens, exploration will probably continue in that zone for another two years. Introduction Summary of Development History of Elk Hills Although a detailed history of Elk Hills oil field is presented in various publications,1,2 a summary of its unusual development and production history will be given in order that the present problems may be more readily understood. The first development that resulted in commercial production was in the central part of the Reserve. The first well, Hay No. I, in sec 36-R,* was completed in January I9I9, and was soon followed by 37 Others in the same general area. It is commonly referred to as the Hay-Carman area and was shut in in stages from 1925 to 1934 as a result of litigation regarding the title to the land. Not being highly producti,, only about 6½ million barrels of oil with a large volume of gas was produced from the area prior to the shutdown. Shortly after the start of the development of the Hay-Carman area, drilling was started 6 miles east in sec 36-S' Tupman NO. I came in for 5000 bbl per day early in I92o, It was followed by more than 200 others in the next few years, and the field became one of major importance. Produc-

Jan 1, 1949

Theoretically mobile primary crushers at the mine working face can be considered the ideal comminution system. A crusher which follows the ore can reduce materials handling costs because it eliminates about one ton of truck deadweight per ton of ore hauled to the crusher. It also eliminates the backhaul of this same deadweight ton. Development of mobile primary crushers has centered in Germany where many soft iron ore and limestone deposits are flat-lying and thus readily adaptable to the use of shiftable conveyors which easily followed the working face. These ores were easily crushed in impact- type mills which had extremely large receiving openings and therefore large reduction ratios. The feeding of such a unit was done with a front-end loader which dumped its load to an inclined apron feeder, which in turn fed the impactor. Under the crusher was an inclined conveyor which transferred the crushed ore to a belt wagon for delivery to the shiftable overland conveyor. Low headroom overhead eccentric single-toggle jaw crushers and short-shaft gyratories were also used on these units, which generally travelled on tracks. While these early mobile primary crushers were versatile and served their purpose, they generally suffered from low capacities. Manufacturers have quickly responded with larger crusher, feeders, and moveable supports, however; and today mobile crusher s have capacities of up to 1500 metric tons per hour, a figure comparable to the capacity of some 54 in. by 74 in. gyratories. An example of a quarry portable crushing plant is at the Bath cement plant of Canada Cement Lafarge, Limited. Two 12 cu yd front-end loaders are digging the stone and hauling it to the portable crushing plant which feeds a field conveyor system. The crushing plant is moved and the field conveyors extended whenever the length of the haul exceeds 300 ft. At the crushing plant, the loaders discharge the stone onto a pan feeder which feeds into the hopper of a Weserhutte-Hazemag compound crusher which combines primary and secondary rotors in the same housing. These are driven at 1200 rpm by 800 hp and 1,000 hp motors (600 and 750 kw). The maximum 3 ft feed (914 mm) is reduced to 3/4 in. (19 mm) at 800 tph. The Weserhutte steered walking mechanism, operated by hydraulic cylinders, takes five -foot strides. Another example is at Alcoa of Australia's operation at Huntley in Western Australia. At the mine face, front-end loaders load 50 mt rear-dump trucks that transport the bauxite ore to the mobile crusher which follows the mine operation. The crusher can turn 360° within its own length, walk at a speed of 34. 5 ft per minute (10.5 m per

Jan 1, 1978

By A. Kaufman

More than 3 trillion gal of water are used annually by the mineral industry. Of this, approximately 21/2 trillion gal are recirculated, the rest constituting intake water. The major users are natural gas processing plants and phosphate rock, sand and gravel, and iron ore producers. Water was used by the mineral industry for mining (6%), processing (64%), cooling and condensing (27%), and miscellaneous uses such as boiler feed and sanitary purposes (3%). Whereas total water use is dependent on the quantity of material processed and on the particular process requirements of an industry, recirculation is dependent on processing, as well as cooling and condensing requirements, quality of new water intake, and the necessity for treating new and discharged water. Consumed water, on the other hand, is dependent on the quantity of water recirculated, and temperature and humidity in the area. Based on this analysis, an increase in water use by the mineral industry of 21/2 times by 1985 is forecast. Wster intake, however, will only rise 62%, because of a substantial increase in recirculation. In one report of a special series concerning the water resources of the United States, the Senate Select Committee on National Water Resources, 87th Congress, estimated that water demand would double by 1980 and triple by 2000.' In view of the possible water deficiencies that might result from such expanded usage and the need for research guidance, the Bureau of Mines organized and carried out a statistical canvass of water use in the mineral industry for calendar year 1962. The data used in this paper, unless otherwise noted, are derived from that canvass.' The efforts in this paper are devoted toward summarization of the canvass and analysis of the data. SOME DEFINITIONS Intake: Water introduced from an external source for the first time into a given mine or plant regardless of quality. Intake water is also called new water, water withdrawn, or makeup water. Fresh Water: Water suitable for cooking and drinking. Saline Water: Water containing more than 1000 parts per million of dissolved solids. Contaminated Water: Water not suitable for domestic use, but excluding saline water. Recirculated Water: Water reused to conserve intake water. Solutions that are recycled primarily because of fixed metallurgical practices, such as copper leaching solutions containing sulfuric acid, are excluded. Gross Water Used: Recirculated water plus intake water. Also called total water used. Consumed Water: Water that is lost by evaporation, as well as water lost in product. Seepage and transferred water are not considered consumed. The use of either intake or recirculated water may result in consumption. However, because of difficulties in measuring consulmption, consumed water is defined as the residual between intake and water discharged from the mine or plant. Mineral Industry: For the purposes of this paper, mineral industry includes all metal and nonmetal surface and underground mines and their associated processing plants, as well as custom mills, coal washing plants and associated mines, petroleum and natural gas well drillers, natural gas processing plants, and secondary recovery operations. WATER USE IN THE MINERAL INDUSTRY Water used by the mineral industry constitutes a relatively minor fraction of the water withdrawn by all users. Data compiled by the U.S. Geological Survey in 1960 indicate that water withdrawals, exclusive of that used to generate hydropower, approximate 99 trillion gal annually.3 Our data indicate that water withdrawals by the mineral industry comprise only 1% of this total, or 2% of the water withdrawn by industrial users. Use by Industry: Water used by various mineral industries is shown in Table I. The table indicates that close to one-half of the gross water used by the mineral industry in 1962 was used by natural gas processing plants, followed by sand and gravel, phosphate rock, and iron ore producers. The largest aggregate users of water are also the largest users per dollar of product. For example, Fig. 1 shows that the natural gas processing and phosphate rock industries are very large users of water per dollar of product. Their recirculation per

Jan 1, 1968

By P. H. Strickland, F. Lawson

It is now well established that in the majority of cementation processes used industrially, the rate of reaction can be described in terms of the mass transport from the bulk of the solution to the deposition sites on the metallic surface. Thus it should be possible to design cementation equipment from a knowledge of the flow situation in the equipment, and of absolute kinetic data. One way of obtaining such absolute data is by the use of the rotating disc geometry; this geometry is particularly suitable for a detailed study of cementation reactions. In spite of the similar mass transfer mechanism, cementation processes differ from other ionic transport processes in at least two respects. The presence of an attached deposit generally has a significant enhancing effect on the reaction rate; and side reactions involving oxygen and/or hydrogen ions can completely change the course of a reaction. Investigation of these peculiarities is necessary for a complete understanding of the process; since they cannot be isolated from the basic mass transport mechanism, close control of experimental conditions is essential. It has been found that the enhancement in deposition rate persists even when the deposit reaches a thickness several times that of the transport boundary layer thickness on the smooth surface. An explanation of the enhancement in reaction rate is proposed.

Jan 1, 1973

By A. Taylor

IN a previous communication,l the quaternary system Ni-Cr-Ti-A1 was described in detail and it was shown how certain alloys used for high-temperature applications could be construed as consisting of Ni,Cr suitably modified by the addition of aluminum and titanium in relatively small amounts. With the correct aging treatment, the ordered face-centered-cubic Berthollide phase, y'-Ni,Al, could be precipitated from the face-centered-cubic primary y-solid solution. By increasing the proportion of titanium with respect to aluminum, it was also possible to precipitate the very brittle hexagonal-close-packed Daltonide phase, ?-Ni,Ti. From the nature of the system it seems reasonable to expect the y and y'-phases to take appreciable amounts of cobalt and iron into solid solution. In the case of the present investigation it was decided to confine the work to iron additions only. This element may be introduced in two quite distinct ways: 1) as a simple replacement for nickel; and 2) as a replacement for chromium, titanium, and aluminum. The second method of iron addition forms the basis of the present investigation, which is, in effect, a study of the pseudo-quaternary system Ni,Cr-NiPe-Ni,Ti-NLAl. For purposes of reference, Figs. 1, 2, and 3 have been included and illustrate the quaternary system Ni-Cr-Ti-A1 described in the previous paper along with sections through N&Cr-Ni,Ti-Ni,Al at 750" and 1000 "C respectively. As will be shown below, the pseudo-quaternary system with components Ni,Cr, NiPe, Ni,Ti, Nihl is remarkably similar in many ways to the face defined by Ni,Cr-Ni,Ti-Ni,Al because of iron re-

Jan 1, 1958

By AIME AIME

THE fifth annual fall meeting of the Petroleum Division of the A. 1. M. E. went down into history as being one of the best ever held by this Division and marked progress was made in the concentration of sentiment regarding several matters-particularly the principles of unit control or operation of oil pools. The first day's program was devoted to the discussion of well spacing and many valuable data were assembled and presented and the discussions following the reading of the different papers was interesting and spirited. However, throughout the whole trend of the discussion it was noted that in the background there was the idea of unit control of the pool and if such a condition could be secured the well spacing theories could be applied much better than could be hoped for if each lease in the pool was treated as a separate and individual unit.

Jan 1, 1929

By A. M. Gaudin, D. W. Fuerstenau, M. M. Turkanis

SOLUBLE silver salts are effective activators for flotation of sphalerite with potassium ethyl xanthate as collector.' Since sphalerite takes up large quantities of silver ions rapidly," investigation of this system appeared fruitful for studying the mechanism of sphalerite activation and deactivation. Experimental data presented here comprise studies of the mechanism and rates of activation and deactivation of sphalerite with silver and cyanide ions. A 20-lb sample of sphalerite from Ottawa County, Oklahoma, was handpicked, crushed, screened, hydrosized to produce a 65/100-mesh fraction, and purified by electrostatic separation. The sphalerite was then leached with benzene and absolute ethyl alcohol to remove possible organic contaminants and with 0.1 M NaCN to remove any copper that might have been picked up during screening. The benzene had been specially purified by grinding with fine sphalerite for 12 hr to remove trace impurities that might have had a specific affinity for sphalerite. Finally, the mineral was washed, dried in flowing nitrogen, and stored in large ground-glass stoppered weighing bottles under a small nitrogen pressure.

Jan 1, 1957