Search Documents

By Bjorn N. P. Paulsson

A number of granitic rock specimens have been studied from the Stripa mine site in connection with a large-scale geomechanics research program. The purpose of the program was to evaluate and develop field and laboratory techniques for rock mass characterization and to determine design parameters for storage of nuclear waste. In this paper a minicomputer-based technique for studying dynamic rock properties in the laboratory is described, together with results from the tests. The specimens were tested under different uniaxial and saturation conditions. Specimens from a field-heated rock mass were also tested to determine if temperatures typical of those encountered with nuclear waste would introduce additional fracturing. Both Vp and Vs increased with stress for both saturated and dry specimens. Both Vp and Vs were higher for saturated specimens at all stress levels compared with the dry. The velocities increased linearly or near linearly with saturation. The test results on the previously heated samples indicate that attenuation is more sensitive to thermally-induced microfracturing than velocities. Analysis of the attenuation values with stress show that rock heated to 200°C is damaged, and that the damage is in form of low-aspect ratio fractures.

Jan 1, 1984

By Persifor Frazer

IN his “Final Report," Vol. II, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

Jan 1, 1877

By E. J. Hall

(Butte Meeting, August, 1913.) THE iron-nail method of assaying has been used for a number of years, but has not met with the approval of all assayers. The method possesses advantages which may be given as follows : (1) no preliminary treatment is required ; (2) a lead button of proper size can be obtained (3) it is economical. On, the other hand, it has its disadvantages, which may be summed up as follows: (1) it is not applicable to ores containing large amounts of impurities other than sulphur, as practically all the base metals will contaminate the lead button ; (2) the slag is unsatisfactory in the larger number of fusions; (3) the method was known to give low silver results under certain conditions and the gold results were questionable. It was with the idea of determining the extent of this latter disadvantage that the following investigation was undertaken. It is well known that the fusion obtained in the lend assay is far more satisfactory than that in the " nails method " for gold and silver. The principal difference in the charges as a class is the presence of considerable reducing agent in the lead charge, and a limited oxidizing action in the nails charge, due to PbO. The possibility of improving the nails fusion by simulating the lead charge was the reason for using argol in some tests, even though there were reasons for expecting this would have -au objectionable effect on the results.

Jan 6, 1913

By AIME AIME

ALL sessions of the Mining Geology Committee at the Annual Meeting this year were held jointly with other groups, a plan that seemed to work out to the satisfaction of every one. Certain of these sessions are reported in this issue by others; the ones held on Wednesday are covered here. Ten papers, as published in the February M&M, were on the program for the Wednesday morning session, held jointly with the Society of Economic Geologists. Mr. Eckel made a brief presentation of his paper, on which there was no discussion, and Mr. Peoples presented that of which he was a joint author. D. M. Fraser then discussed a gravimeter survey for chromite in Cuba, which blocked out some 50,000 tons of ore, and F. G. Wells told of work on chromiferous sands in Oregon.

Jan 1, 1943

By S. D. Michaelson

[CONTENTS PACE See TP 2377, Min. Tech, May 1948 for discussion of A Technique for Photographing Difficult Subjects through a Petrographic Microscope (TP 2092 by DONALD W. SCOTT, Min. Tech., Nov. 1946. Discussion by HORACE WINCHELL). Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy (TP 2141 by R. A. ....... PALLANCH, Min. Tech:, March 1947. Discussion by S. D. MICHAELSON). I Symposium on Milling Devices and Practices. (TP 2162 by J. F. MYERS and R. J. TOWER, Min. Tech., May 1947. Discussion by HARLOWE HARDINGE). ............ 2 Rod Milling-Plant and Laboratory Data. (TP 2175 by J. F. MYERS, S. D. MICHAELSON and F. C. BOND, Min. Tech., July 1947. Authors' supplement and discussion by HARLOWE .......................... HARDINGE, and B. H. IRWIN) 2 A New Separating Vessel for Sink-float Concentration. (TP 2182 by E. C. BITZER, Min. Tech., May 1947. Discussion by E. H. CRABTREE, JR.) .................. 5] Metallurgical Efficiency-a Yardstick in Lead-zinc Flotation Metallurgy S. D, MICHAELSON*-The method of determining the efficacy of a separation described in this paper, gives the metallurgist a most useful guide for keeping his ship on an even keel When the ore Waves vary from placid seas to high breakers. Now that such a method of evaluating metallurgical efficiency has been developed and proven practical, it Would seem logical to introduce the next, and more final, factor of Economic Efficiency. I choose to define this term as the percentage ratio of net return from milling to the theoretical maximum net return. The actual operating cost subtracted from the actual mill return represents the net actual amount received for the material treated. Experienced operators of most plants Would ordinarily have enough data on hand to estimate a theoretical milling cost per ton, based on labor, power, supplies and maintenance When operating at maximum tonnage With minimum trouble and under ideal ore conditions. When this theoretical estimated cost is subtracted from the theoretical maximum ore return (calculated by Pallanch's method) the resulting figure is the maximum theoretical net amount the mill operator could hope to realize in processing the ore. The percentage ratio of these sums, of actual to theoretical, is the economic efficiency of the operations. This economic efficiency, if determined on the basis of a fixed market price for metal and similarly fixed base rates for labor, power and supplies, Will reflect the effect of changes in milling practice, labor efficiency and equipment condition. When computations made on the basis of actual current rates for labor, power and supplies are compared With similar actual figures for past periods they will show forcefully how energetic our hunt must be to develop man saving controls, more effective metallurgy, and better equipment to maintain profitable operations. Such computations also offer a simple means of determining how much more labor, supplies and power can be put into the mill operation to obtain an increase in metallurgical recovery at a profit.

Jan 1, 1947

By Walter W. Lilly, Issa S. Oweis

Application of rock engineering in geotechnial consulting practice considered herein is in areas of: (a) bedrock verification for foundation support, (b) bearing capacity and settlements, and (c) excavations. A routine geotechnical investigation usually provides data on depth to rock, rock classification, and rock quality. In cases of rock outcrop, such outcrops are mapped for geologic structures and rock mass description. In addition, the regional geology and the general aspects of the groundwater regime are usually known from either published literature or previous experience. The predominant technique for ground and site investigation are usually drilling and geologic reconnaissance. Other techniques involving seismic and geophysical soundings, borehole camera, and oriented cores are used by by no means routine. Performing laboratory strength and compressibility tests is often made to be considered as routine. The use of the point load test is gaining increasing use in the United States and would, perhaps, become a routine field or laboratory test due to its simplicity and, more importantly, its relatively low cost. The purpose of this paper is to describe cases where mostly routine investigation and testing were used to arrive at engineering decisions. Bearing Capacity and Settlements The allowable bearing values for foundation support on rock is usually dictated by local building codes which presumably should reflect local experience. The interpretation of the code, however, can present a problem, especially if the interpretation is made by a designer under the delusion of knowledge in rock engineering. For

Jan 1, 1982

By Edward Keller

Someone some time ago remarked that some chemists still insist on telling us how to determine copper by the electrolytic method. The writer must confess that he believes that everything is not known definitely as yet as to how the exact amount of copper is determined in such material as purest commercial electrolytic copper. Some of us are not yet convinced that the pure copper atom is at all times deposited from an acid solution and that no oxygen or hydrogen will, under certain conditions, accompany it. Difficulties with impurer material are frequent, but erroneous results are not always apparent, since these do not speak so readily for themselves as those in the first case. By this is meant that if a chemist finds 100 per cent. of copper in electrolytic copper it is pretty certain that he perceives the result to be wrong, while if he finds 0.1 per cent. of copper too much in a very impure material he is far more likely to be unconscious of his error. These, in a wide experience, are frequent happenings and the writer has always looked with interest to publications on this subject. In turn, he feels justified in giving to others a few of his own observations. Up to a few years ago there were two methods of electrolytic copper assay in technical use, which had in common, that the amount of copper deposited on the cathode did not exceed 2 g., and they differed in that, for the one a large sample1 (20 to 80 g.) was taken from the general sample by a splitting device, dissolved, and from the solution a small portion (to contain 1 or 2 g. of copper) measured out for the electrolytic deposition; in the other method the copper was determined, generally in 1-g. portions of the separated coarse and fine portions of the sample, all of which passed a 16 or 20-mesh screen, being accomplished by a 40-mesh screen,

Jan 1, 1914

By Persifor Frazer

In his " Final Report," Vol. 11, part second, p. 763, Prof. Rogers sums up the metalliferous veins of the mesozoic sandstone by remarking that these are not associated with dykes or trap-rock, but are independent metalliferous injections. But singularly enough, in enumerating the different kinds of ores, no mention is made of

By P. P. Gregory

Natural petroleum gas occurring in the oil-bearing reservoirs is found to exist either as free gas associated with the oil and/or in solution in the oil. In some virgin fields practically no free gas is encountered under the reservoir conditions of pressure and temperature, although in other fields a considerable section of the "pay" horizon is occupied by free gas. In other words, a given oil field may or may not have a gas cap before the exploitation takes place. However, when the reservoir pressure is reduced to a point below the critical saturation pressure by withdrawals of fluids from the producing formation, the gas dissolved in the oil inevitably begins to come out of solution and becomes free gas. Under the controlled methods of production and drilling, a portion of this gas is produced with the oil to the surface and a portion of it remains within the reservoir to accumulate at higher structural levels toward which it migrates by virtue of its low specific gravity. The rate of growth of a gas cap in a given structure depends primarily upon the rate of decline in the reservoir pressure. If the rate of pressure decline is rapid, the gas cap likewise will grow rapidly. On the other hand, shrinkage in the gas-cap area was noted in some fields in which reservoir pressures wereincreasing. Determination of Gas-oil Contact and Thickness of Gas Cap The gas-oil contact can be conveniently located in the process of drilling a well and by electrical logging. However, very little can be found in the petroleum literature concerning methods of predetermining gas-oil contacts in producing reservoirs. Therefore, the writer feels justified in describing briefly a simple, workable, and inexpensive method of determining gas-oil contacts and outlining the limits of gas-cap areas in a field where such knowledge may be essential for efficient production and development operations. The method involves the determination of the following data: (I) Structural data, such as the depth or elevation of the top' of "pay" horizon; (2) reservoir pressures; (3) tubing and casing pressures at the well head; (4) static oil-pressure gradient; (5) static gas-pressure gradient. These data can be secured with a minimum of expense, inasmuch as the

Jan 1, 1938

By D. G. Swarthout, J. W. Savage, R. W. Guard

The Nb-N constitution diagvam has been examined from 1100° to 1450°C at 1 atm N2 pressure. On the basis of- our work plus that of Brauer and coworkers the stable nitvide Phases are: a) a solid solutlion, basic niobium (bcc) with nitrogen contained interstitially; NbN,, x = <0.40; b) ß NhNx,x = 0.39 to 0.45; hexagonal (W2C type) (NbzN); a =3.058A,c = 4.961 + 0.001A c) y NbNx x = 0.75 to 0.80; tetragonal (distorted NaCl type) (Nb4N3); a = 4.386A,c = 4.332 + 0.001A; d) 6 NbN,, x = 0.88 to 0.91; cubic (NaCl type); a = 4.3885 + 0.0007A; e) E NbNx x = 0.92 to 1.00; hexagonal (Tip type); a = 2.958A, c = 11.272 * 0.0015A. In addition, a metastuble transition phase 6&apos; has been observed and occurs only during the transition 6 — E. 6&apos; NbN has these distinguishing parameters: NbNx,x = 0.96; hexagonal (anti-NiAs type); a = 2.94A, c = 5 .46A. The high-temperature phase fields in the system are governed by two reactions: a) 6 + Y + E, a entectoid reaction occurring at 1270" ± 20° C; b) o + N2 = E, a 2 012 1 reaction occurring at 1370" ± 20° C. As part of a study of the electronic low-temperature. properties of transition metal nitrides, a number of specimens of niobium nitride were prepared. Preliminary observations on these specimens showed several points of disagreement with data already in the literature. It was, therefore, decided to determine the constitution diagram for the Nb-N system between 1100" and 1450°C. The objective of this research was to define the temperature and composition regions of stability of the various phases and to explain the differences among previously proposed diagrams. Review of Previous Literature. The research on the Nb-N system to 1964 has been summarized by storms.&apos; Although he does not present a phase diagram, his review covers the research on the system thoroughly. One of the earliest works on NbN is that of Ascher-mann and coworkers2 who studied the superconductivity of the cubic 6 NbN. Subsequent work by Horn and ziegler,3 Cook, Zemansky, and Boorse,1 Rögener:5 Schroder6 and sellmaier7 has qualitatively confirmed the first results on superconductivity, although their methods of preparation differed considerably. The constitution diagrams proposed for the system by Brauer and Esselborn8 and Elliott9 are shown in Fig. l(a)and (b). The diagram in l(a) has been modified by more recent results in Brauer&apos;s laboratory (private communication). Although 6&apos; is shown on this diagram, Brauer has indicated that he now believes 6&apos; to be a metastable phase in the temperature range shown. The diagram of Elliott, Fig. l(b), is based primarily on the results of Elliott and Komjathy10 on ni-trided niobium strip or rod specimens examined by X-ray diffraction and metallography. It will be noted that these proposed diagrams are in conflict with respect to the temperature and composition ranges of

Jan 1, 1968

By Richard Hunt

BINGHAM has produced 6 per cent. of this country&apos;s copper. In total production, it ranks fourth among the copper camps of North America, the order being Butte, Michigan, Bisbee, and Bingham. In its annual production, it held that same rank until 1919, when its production was exceeded by the combined production of the Globe-Miami district of Arizona. Bingham has also been a lead camp of the first order. Utah ranks third among the lead-producing states, and its production comes largely from three camps which, in the order of their productivity, are: Bingham, Tintic, Park City. Bingham&apos;s silver production is important, but it does not rank high as a silver producer. Utah owes its rank as first among the silver-producing states to Tintic, a camp 40 miles due south of Bingham. The United States Mineral Resources reports a total production from Bingham for the period 1865-1920 having a gross value of $528,043,432. Bingham is on the eastern flank of the Oquirrh range 30 miles south-west of Salt Lake City, from which it can be reached in an hour by auto, or by the Denver & Rio Grande or the Bingham & Garfield railroads.. The automobile route is a paved road across the floor of Great Salt Lake Valley, through farming country. The Bingham & Garfield railway leaves the level of Great Salt Lake at the northern end of the Oquirrh range, and in 20 miles it climbs 2100 ft., and deposits the traveler upon a shelf cut in the side of Bingham Canyon below most of the mines, which are farther up Bingham Canyon and its tributary Carr Fork. Below lies the town, a narrow ribbon running for a couple of miles along the bottom of a canyon 2000 ft. deep-an almost impossible site for a community numbering, in prosperous times, 5000 to 7000 inhabitants drawn from all quarters of the globe. Up the canyon and down, and beneath the steep slopes nearby, and beneath the town itself, are the mining operations of over half a century.

Jan 3, 1924

South Dakota State School of Mines, Rapid City, S. D. C C O&apos;Harris,-President. A number of technical bulletins have been issued at the South Dakota State School of Mines but, unfortunately, most of them are out of print and as this directory is concerned only with available publications, the following are all that are now to be had Bulletin 11, A bibliography of the geology and mining interests of the Black Hills region (1917), no charge; 14, The geology, mineralogy, and scenic features of Custer State Park (1926), 40 cents plus postage on 1 lb ; 15, The Tertiary mineralization of the northern Black Hills (1927), charge, postage on 1 1b.; 16, The mineral wealth of the Black Hills t418 pages) (1929), 80 cents plus postage on 3 lb

Jan 1, 1933

By J. B. Clark

An exploratory study of the 60 wt pct Mg and 80 wt pct Mg sections of the solid constitution in the magnesium-rich region of the Mg-Al-Ca-Zn system was undertaken. The objective of the investigation was to determine the general configuration of the phase fields with respect to the magnesium solid solution in this complex system. The 335°C (635°F) tetrahedron was selected for study because the solid constitutions of the bounding ternary systems—Mg-Al-Zn,1 Mg-A1-Ca,2 Mg-Ca-zn3—were well known and, at least in these ternary systems, diffusion was rapid enough at 335°C for equilibrium to be reached fairly rapidly. Metallography and powder X-ray diffraction were selected as the best corroboratory methods for determining the solid phase equilibria. A total of forty-six quaternary alloys on the 60 wt Mg and 80 wt Mg sections were prepared, annealed to equilibrium at 335°C, and the phases present identified. Singly sublimed (99.99 pct) magnesium, electrolytic (99.99 pct) zinc, high-purity (99.99 pct) aluminum, and USP calcium were alloyed in graphite crucibles under a chloride flux and chill cast into a split graphite mold. Alloy samples were sealed under argon in Pyrex vials and annealed at 335°C ± 1/2° for a minimum of 500 hr. At the conclusion of the anneal, the alloy samples were quenched rapidly in ice water. Standard metallographic procedures for magnesium alloys were used. Powder X-ray diffraction patterns were taken on a G. E. Camera with a diameter of 14.32 cm using nickel filtered copper radiation. The phase equilibria in the 60 wt pct Mg section of the 335°C (635°F) tetrahedron is shown in Fig. 1. The complex equilibria in the zinc-rich region were not accurately determined and are shown only tentatively with dotted lines. The equilibria of the three bounding ternary 335°C sections from pure magnesium to 60 wt pct Mg are also shown as though folded away from the tetrahedron. The 80 wt pct Mg section has the same configuration of phase fields as that shown in Fig. 1. Thus it is reasonable to conclude that in higher magnesium sections, the same relative configuration of phase fields is maintained though the relative proportions of the individual phase fields may change slightly as the magnesium solid solution is approached. Note that all the ternary phases present in these ternary diagrams enter into the quaternary equilibria with the exception of the phase of the Mg-Al-Zn system which becomes unstable with the addition of as little as 1/2 pct Ca. No quaternary intermetallic phases were found. No liquid phase was detected in any of the quaternary alloys annealed at 335°C suggesting that if a quaternary eu-tectic exists, it must lie between 335°C and 339°C, the temperature of the ternary eutectic in the Mg-Al-Zn system.

Jan 1, 1962

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

SULFURIC ACID U.S. 4,070,260 - Sulfuric acid leaching of willemite, hemimorphite, or other zinc silicate ore. Ore is leached with at least a stoichiometric amount of a IN to 6N sulfuric acid solution at a temperature near its boiling point to form a gelatinous mass of hydrated silica and zinc sulfate, the water in the mass partially evaporated to crystallize all of the silica, the mass treated with hot water to dissolve substantially all of the zinc sulfate, the suspension filtered, and zinc values recovered from the filtrate by electrolysis. N. Dreulle, assigned to Compagnie Royale Asturienne des Mines. Jan. 24, 1978. 3 pp. (204-119). Filed: 2-10-76 (656,966) . Priority: France, 2-14-75 (75/04594) .

Jan 1, 1979

By John A. Wolfe

The brightest spot in the mineral economy of the Philippines is the rapid development of reserves and production of copper. If economic conditions remain favorable and the political climate is encouraging, production of this metal should increase at a rate of 25% per year for several years, long enough to rank this country as one of the major copper producers of the world. In 1965 the copper content of the Philippine concentrates was approximately 60,000 tons. It should total about 80,000 tons in 1966. A major part of the increase will come from the rich Lepanto mine located in Mountain Province, North Central Luzon. Daily production of ore increased from 1200 to 2000 tons at the end of 1965. The ore, consisting of enargite and luzonite, averages nearly 3% copper and 0.12 oz. of gold per ton. It is an under- ground operation with a cutoff grade of 2%. The ore is associated with extensive silicification under a volcanic cap rock. Further expansion to increase ore production to 2600 tpd is under way.

Jan 4, 1967

By R. W. Armstrong, P. C. Jindal

The hardness dependence on grain size for polycrys-talline cartridge brass and a leaded brass has been measured by Brine11 and Rockwell B testing. In each case, the hardness, H, depends on the average grain diameter, 1, according to: H =Ho + kHl-1/2 where Ho and kH are experimental constants. Diamond pyramid hardness values have also been measured as a function of the indentation size and grain size to give additional information on the nature of the hardness test and the dependence of hardness on micro-structure. The hardness of polycrystalline brass depends on its grain size. Bassett and Davis&apos; demonstrated this as early as 1919 by making Brinell hardness measurements on cartridge brass. Since then, the hardness of this type of material has been measured as a function of grain size by making Rockwell,2&apos;3 Vickers,4 and Brinell5 tests. he hardness dependence on grain size has also been measured for other materials. Angus and summers6 investigated the grain size dependence of the Brinell hardness of polycrystalline copper and a Cu-4.5 pct Sn bronze. In other studies, nickel,? Armco iron,Big an Fe-0.07 pct C alloy,I0 and an 0.39 pct C-12.45 pct Cr stainless steel" have been investigated. In some of the preceding cases, the hardness results have been analyzed to show that the hardness varies with the average grain diameter, 1, according to an l-l\4, l-1/4 or I-2 dependence,11-13 The studies of the influence of grain size on hardness have not been based on any theoretical model. This may be because the hardness of a material is itself a complicated property. However, attempts have been made to correlate, experimentally and theoretically, the hardness of a material with its unidirectional stress-strain behavior.14-l6 On this basis, Hall" proposed that the polycrystal hardness dependence on grain size might follow directly from the Hall-Petch18,19 relation for the grain size dependence of the yield stress. Thus, the hardness-grain size relation was given as: H = Ho + kHl-1/2 [1] where Ho and kH were taken as experimental constants. The relation was applied to the measurements on brass,&apos; copper,6 bronze,= and Armco iron.&apos; More recently, this relation was shown by Armstrong and jindal20 to adequately describe the measurements on cartridge brass made by Bassett and Davis&apos; and Babyak and Rhines.5 In this case, the relationship was taken a step further by independently relating the values of Ho and kH to the values of oyand ky, previously reported by Armstrong, Codd, Douthwaite, and petch21 from measurements of the yield stress dependence on grain size for this type of material. In the present investigation, new Brinell and Rockwell B hardness measurements have been made as a function of grain size for a cartridge brass and a leaded brass. In addition, diamond pyramid hardness values were measured as a function of the indentation size. All these results are applied to a further analysis of the hardness dependence on grain size. MATERIALS AND EXPERIMENTAL METHODS Cartridge brass and a leaded brass were selected for this investigation for two main reasons: it was anticipated 1) that these materials could be cold-worked and recrystallized to a wide range in grain size and 2) that the results to be obtained on these typical industrial materials could be usefully compared with previous investigations. The chemical analyses of the actual materials which were employed are given in Table I. The as-received 1/2- and 3/4-in.-thick plates were given various reductions in thickness by cold rolling. The rolled material was heat-treated at various temperatures between 330" and 850°C for differing time periods from 5 min to 9 hr to achieve a variation in the average grain diameter between 0.0339 and 0.000543 cm.22 During heat treatment, the brass was protected from zinc loss by packing it in chips or foils of the same composition material. Reasonably equi-axed grain structures were obtained in each case. The metallurgical grain sizes of the specimens were determined from measurements of the average linear intercept on a random line. Annealing twin interfaces were not counted along with grain boundaries. The

Jan 1, 1970

By L. A. Weitzenkamp, N. M. Bashara

A study of the electrical conductivity of gold films less than 200 in thickness indicates a negative temperature coefficient of resistance and a thermal actiuatlon energy of less than 0.25 ev. The films consist of discrete metal islands of linear dimensions from a few angstroms to 1000A. Films were able to withstand applied fields up to 60,000 v per cm before breakdown occurred. A model for the conduction mechanism is proposed which involtes a Potential barrier due to work junction, irriage forces , and an electrostatic potential arising from separating an electron from a neutral island leaving behind a positively charged metal island. Activation energies of less than 0.25 ev ave consistent with this model, which includes a tunneling andor Thermal mechanism for conduction between the separate metal islands. An apparent satuvation effect in conductivity at high fields is observed experimentally. The saturation effect may be explained by the influence of the electrostatic contribution to the potential barriers for the transition through several islands adjacent to the original island which was activated to give up an electron. The proposed model gives Poor quantitative agyeement for the intermal electrical field between islands. ThIS paper will relate the structure of discontinuous metal films to the electrical properties and will emphasize the following topics: 1) the relation of the conduction mechanism to particle size and a comparison of particle size from electrical measurements with electron-microscope studies; 2) the saturation of the conductivity at high electric fields; and finally, 3) a comparison between the external field applied and the apparent field between particles. che- latter comparison points to a need for a modification in the model for the conduction mechanism first proposed by orter&apos; and expanded by Neugebauer and webb2 which will be dealt with in the discussion. The paper is based on results on gold films on glass microscope slides. The clms were vacuum-evaporated and were about lOOA thick, thickness being measured by interferometry. It has been observed that metal films of this thickness do not exhibit bulk metallic conduction. Films thinner than some critical thiclmess, depending upon substrate temperature and other factors, have conductivities which increase with increasing temperature with thermal activation energies of less than 0.25 ev. Electron-microscope studies3 have shown that these films consist of discrete metal islands having linear dimnsions from a few angstroms to approximately 1000A. When the metal is being vacuum-deposited on the substrate, islands on the order of a few angstroms appear first. As the deposition continues the islands may tend to agglomerate into larger particles and may eventually grow together into a continuous film,3&apos;&apos;&apos; In our tests the conductivity of the gold films was found to be about ten orders of magnitude less than the bulk conductivity of gold. When oxygen was introduced into the test chamber the conductivity decreased by a factor of about one-third. This can be related to an increase in work function for gold caused by adsorption of oxygen, as reported by Oullet and Rideal.s Exposure to an atmosphere of water vapor caused an increase in conductivity by a factor of 2 or 3 when a low field was applied. When the films were exposed to water vapor under a high field the conductivity increased by as much as two orders of magnitude. The activation energies measured were much less than the work function for gold, 0.25 ev or less, with the smaller activation energies observed for thicker films. It will be shown that the activation energy is a function of particle size and spacing. In general the model for the potential between metal islands would include the effective work function, the image force, the applied field, and an electrostatic term. The electrostatic contribution arises from the potential required to separate an electron from a conducting sphere. According to Neugebauer and webb2 the maximum potential due to the field and the electrostatic term only is

Jan 1, 1967

By D. E. Spiller

Introduction Precious metals recovery from ore can generally be accomplished using gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems that employ leaching as the primary unit operation. A brief discussion of modem gravity concentration equipment is also presented. Discussion Gravity concentration of ores has generated increasing interest in recent years. Reasons for this interest include: • Gravity concentration is environmentally attractive. There is little or no use of reagents. Hence, it is relatively nonpolluting. • The cost of cyanide has continued to increase. Therefore, cost savings may be realized whenever leaching feed tonnage can be reduced by preconcentration. • Compared to flotation and leaching, gravity equipment costs are low per processed ton. Field installation costs for gravity circuits usually are less because many&apos; units are supplied as self-contained modules. Also, the cost required to supply services, particularly power, to a gravity plant site are also less. In situations where preconcentration at coarse particle size is applicable, significant grinding equipment savings may be possible. • Gravity circuit operating costs are also relatively low compared to typical flotation and leaching circuits. Reagents, power, maintenance, and manpower savings in a well-engineered gravity plant may be realized. Again, if grinding is reduced, significant power and steel (media and liners) savings are possible. •In recent years, more efficient gravity concentrating devices have been developed. Benefits to Precious Metal Leaching Gravity beneficiation can complement precious metal leaching in two ways. First, the recovery of coarse liberated values before leaching may reduce leach time requirements and may reduce reagent consumption. Second, gravity preconcentration can reduce the size of a leach plant by decreasing the quantity of material to be leached. Coarse gold and silver have been shown to leach rather slowly. Kameda (1949) and Habashi (1967) have investigated the kinetics of cyanide leaching systems. They concur that in a heterogeneous reaction, the rate of gold and silver dissolution is directly proportional to the surface area. Thus, the instantaneous rate of dissolution for spherical 0.37 mm (400 mesh) gold is theoretically -25 times faster than for the same amount of gold at .841 mm (20 mesh), based on data from Fuerstenau, Chander, and Abouzeid (1979). Conversely, coarse liberated, +.841 mm (20 mesh), gold is more readily recovered by gravity concentration than is fine, -.037 mm (400 mesh) gold. Therefore, it is apparent that the two recovery systems complement one another. Figure 1 data demonstrates the potential synergism. A sample of - 3.327 mm (6 mesh) Nevada gold-bearing ore was cyanide leached using conventional bottle-roll test procedures. Gold extraction was determined as a function of leaching time. A second sample split from the same leach feed material was hand jigged to remove a coarse heavy mineral fraction, including virtually all of the +.210 mm (65 mesh) liberated free gold. This second sample, with the coarse gold and heavy minerals removed, was subjected to an identical cyanide leach procedure. Figure 1 presents the resulting comparative extraction data. Note that the percent gold extraction for the sample containing no +.210 mm (65 mesh) free gold includes the coarse gold recovered by gravity. The data show that the sample containing coarse gold required about 72 hours of leaching time to achieve 80% extraction. This compared to about 22 hours of leaching time for 80% gold recovery from the sample that contained only -.210 mm (65 mesh) free gold. Thus, there was a 69% reduction in leaching time. The improved extraction data is not wholly attributable to coarse gold removal, but rather it was the combination of gold removal and rejection of other heavy mineral cyanide consumers or leach retardants. Further investigation was not warranted at this time. Preconcentration is the second manner in which leaching systems can benefit from gravity concentration. The premise is that preconcentration can reduce the quantity of leach feed, which, in turn, may reduce leaching costs. Figure 2 presents preliminary data developed by CSMRI for US Minerals Exploration (USMX). Centennial Exploration Inc., in agreement with USMX, is proceeding with evaluations to determine the suitability of various processing schemes for recovery of gold values from the Montana Tunnels property. The data shows how the ore can be preconcentrated by gravity techniques to result in a reduced feed tonnage to secondary extraction techniques, presumably flotation or cyanide leaching. Testing has shown that Reichert cones, followed by treating the cone concentrate on spirals, can deliver about 88% gold recovery in about 13% weight, that is, 87% weight rejection. Consequently, fine grinding and reagent costs are attributable to only 13% of the plant feed rate. Cost data is not yet available, but the potential exists for significant cost savings.

Jan 1, 1985

By H. D. Kessler, R. J. Van Thyne

Phase diagrams of the titanium-rich portion of the ternary systems from 0 to 10 wt pct Al and 0 to 1 wt pct 0, N, and C were determined. Micrographic analysis of annealed high purity arc melted alloys was the principal method of investigation and was supplemented by X-ray diffraction. TITANIUM-ALUMINUM alloys exhibit excellent properties, particularly for elevated temperature use. For this reason, the Materials Laboratory, Wright Air Development Center, sponsored an investigation of the effect of the interstitially soluble contaminants, oxygen! nitrogen, and carbon, on the Ti-A1 system. Using high purity arc melted alloys and micrographic analysis of annealed samples as the chief method of investigation, titanium-rich partial phase diagrams were determined for the ternary systems. Experimental Procedure Materials: The titanium used in the preparation of the alloys was iodide crystal bar (99.9+ pct pure) produced by the New Jersey Zinc Co. and Foote Mineral Co. The aluminum was obtained from the Aluminum Co. of America in the form of sheet. The given analysis was: Si, 0.0006 pct; Fe, 0.0005; Cu, 0.0022; Mg, 0.0003; Ca, <0.0006; Na, <0.0005; and Al, 99.99. High purity titanium dioxide purchased from the National Lead Co. was used in the preparation of the oxygen-bearing alloys. The spectrographic analysis of this material was as follows: SiO,, 0.07 pct; Fe,O,,, 0.002; A1,0,, <0.001; Sb,O,, <0.002; SnO,,, <0.001; Mg, <::0.001; Cb, <0.01; Cu, 0.0004; Pb, 0.002; Mn, <0.00005; W, <0.01; V, <0.002; Cr, <0.002; Ni, <0.001; and Mo, <0.002. Special spectroscopic graphite rod purchased from the National Carbon Co. was used in the preparation of the Ti-A1-C alloys. Alloy Preparation: Alloy ingots weighing 10 grams were melted in a nonconsumable tungsten electrode arc melting furnace using water-cooled copper hearths and a helium atmosphere. The arc was struck on a tungsten stud in the copper block to minimize contamination from the electrode. Details of the techniques have been reported.&apos;, &apos; Each ingot was inverted and remelted a minimum of four times to insure homogeneity, without opening the furnace. Remelting small control ingots of iodide titanium under similar conditions resulted in no measurable hardness increase, indicating contamination-free melting conditions were used. The alloy charges and resultant ingots were weighed to the nearest milligram. Only small weight losses were obtained upon melting, indicating that the actual compositions were very close to the nominal compositions. Check analyses substantiated this. Oxygen and nitrogen were added during ingot preparation as master alloys. An oxygen master alloy containing 25 wt pct 0 was prepared by melting iodide titanium and pressed titanium dioxide (40 pct 0) powder. The Ti-25 pct 0 alloy is more easily handled during weighing and charging than the pressed TiO, powder. Chemical analysis indicated that titanium-nitride received from an outside source contained large amounts of impurities (2.7 pct Ca). Therefore, a master alloy containing approximately 12 pct N was prepared by melting nitrided sponge titanium. As the sponge melted with difficulty, the alloy was diluted by addition of titanium to lower the melting point. The chemical analysis of the final alloy was 6.69 pct N. Both master alloys are friable and were used as —8 +16 mesh lumps resulting from crushing the ingots. NIelting the Ti-A1-0 and Ti-A1-N compositions five times produced homogeneous ingots. The preparation of homogeneous carbon-bearing alloys caused considerable difficulty. Alloys containing less than 1 pct C were prepared using spectrographic graphite rod, 1/8 in. diameter by 1/8 in. long. However, the graphite did not dissolve even with long melting times and many remelts. The ?/s in. pieces of graphite were used rather than powder because the low density powder is troublesome in arc melting.

Jan 1, 1955