Search Documents

By Arthur Gates

INTRODUCTION RITTINGER'S law of the energy expended in crushing is, as roughly stated by Professor Richards,1 that the work of crushing is proportional to the reduction in diameter; or, as I have more fully expressed it: "The work done in crushing is proportional to the surface exposed by the operation; or, better expressed for this purpose, the work done on a given mass of rock is proportional to the reciprocal of the diameter of the final product-assuming that all the mass has been reduced to one exact size, which is only theoretically possible.?2 Kick's law is stated by H. Stadler as follows:3 "The energy required for producing analogous changes of configuration of geometrically similar bodies of equal -technological state varies as the volumes or weights, of these bodies." In other words, the energy expended is porportional to the volume reduction, instead of the diameter reduction. That these two laws would give widely different results may be shown by a simple imaginary case. A ton of 16-in. cubes is broken to 1 -in. cubes at the first operation, and these are broken to 1/16 -in, cubes at a second operation. Since the first operation produces only one-sixteenth as much new surface as the second, the ratio of energy expended in the two operations would be by Rittinger's law as 1 to 16. By Kick's law, since the volume-reduction ratio is the same in both cases, the ratio of energy would be 1 to 1. This discrepancy is great enough to challenge a test by actual experiment, of which there has been, hitherto, but little compared with the amount of argument. The present paper is the record

Jan 9, 1915

By Elmars Ence, Harold Margolin

The titanium-aluminum system has been investigated in the composition region 0 to 34 pct Al in the temperature range 800" to 1450°C. The phases encountered in this region were: a,ß, TiAl3, The reactions observed are as follows: 13 ; L - 6T. A1, 0 (15 pct Al) + 6 (18 pct Al) - yTi Al (16.5 pct Al) at -1170°C andP (7 pctpct Al) + y (9.2 pet Al) - ah(9 pct Al) at - 1060°C. A eutectoid reaction: y — a +d belm 700°C is postulated. THE Ti-A1 system has been the sub.ect of a number of investigations. Several of these1-3 have indicated extensive solubility of A1 in both a and ß titanium. Ence and Margolin, as a result of work on the Ti-A1-0 system:'5 have shown that the a solubility ofalumi-num is considerably restricted, and found that a compound, Ti2A1 existed in the region formerly designated as Q a This structure was identified as hexagonal with c/a = 0.803. Pietrokowsky confirmed the existence of this phase7 and pointed out that the structure was isomorphous with Ti3Sn.8 Although the existence of Ti,A1 has been confirmed by others,9-12 there has been considerable disagreement regarding the composition and mode of formation. A detailed reinvestigation of the Ti-A1 system has been published by Sagel et al.13 The tentative diagram indicated two phases, a, and e, occurring in the former all a region. The a, phase has the same structure as Ti2A1 and was indicated as having a broad region of solubility. Epsilon, a tetragonal phase, was shown to form within the a, solubility region. AS a result of unpublished work,14 Ence and Mugy3 olin disagreed with the interpretation of Sage1 et al., although some common features existed. The present study was conducted in an attempt to clarify prevailing uncertainties. EXPERIMENTAL PROCEDURE Alloy Preparation—Alloys were prepared from iodide titanium (99.9 pct Ti with less than 0.01 pct Zr) or Bureau of Mines electrolytic titanium (BHN-73) and high purity aluminum (99.99 pct). Alloys were arc-melted in argon or helium atmosphere as 15-g buttons in the composition range up to 34 pct Al. Depending on need, alloys were made in increments varying from 0.25 to 2 pct Al. Up to five 15-g buttons of some compositions were made. Weight losses during melting did not exceed about 1 pct of the charge and chemical analysis revealed that both titanium and aluminum were evaporated. In general, nominal and analyzed compositions agreed within 0.5 pct and therefore nominal compositions were used in plotting the data. Unavoidably, some overlap of composition occurred, particularly where small increments of A1 were used. The small increments were primarily used to obtain alloys which would fall into the narrow a -, r region and this purpose was achieved. In general, the data obtained from Bureau of Mines base titanium and iodide titanium alloys were in agreement. Forging—Both as-cast and forged samples were employed. Samples were heated for hand forging by an oxygen-hydrogen torch to the region 1200" to 1300°C. A titanium anvil and cover plate were used to prevent any iron pick-up and consequent formation of a low melting point compound. Frequent reheating kept the temperature in the desired range. Under these conditions, alloys containing up to 15.5 pct could be successfully forged. To check on the depth of contamination, forged alloys were heated slightlybelow the ß transformation temperature. Metal was removed to a depth below the contaminated surface so revealed, and the subsequent results obtained from these samples agreed closely with those secured from as-cast material. Heat Treatment—Prior to heat treatment, all alloys were vacuum annealed to remove hydrogen. Samples

Jan 1, 1962

By Paul B. Crawford, Melvin B. Burton

A procedure is given which describes how the gelatin model may be-used to study the effect of mobility ratio on areas swept before and after breakthrough in fluid injection programs. Differences in mobility ratio are achieved through the proper selection of electrolytes for the invading and displaced fluids. The progress of the front is followed visually and photographed or traced onto plates (it desirrd positions before and after breakthrough. Example applications to standard flooding pattrrrls, vertically and horizontally fractured reservoirs and the in-situ combustion recovery process ore presentrtl. INTRODUCTION In water flooding, gas cycling and other fluid injection programs, the sweep efficiencies and swept areas after breakthrough are known to depend on the mobility ratio. Previous investigators have described the application of the X-ray technique, stepwise use of the poten-tiometric model and numerical procedures for studying these problems.1,3,4,6 Others have described the application of the electrolytic and gelatin models for studying sweep efficiencies at a mobility ratio near one.2,5,7,8,9 It is a purpose of this paper to describe a procedure for using the gelatin model to study swept areas at mobility ratios other than one. PROCEDURE The technique developed for gelatin model studies is composed of four phases: the construction of the model, the selection and preparation of electrolytes, the running procedure, and the recording of the swept areas. Each phase is discussed independently in order that the over-all procedure will not be confused. Construction of the Model Since some of the advantages of the gelatin model are its economy, and speed, it is desirable to have as small a model as is possihle without creating error through the inability to follow visually the progress of the colored front. For this work, it was found that a distance of 4 to 6 cm between salt bridges is convenient to use. Since the size is relatively small, it follows that the gelatin layer must be thin. For this study, 1/8 in. was used as the gelatin thickness in each case. The model was constructed on a flat 1/2-in. plastic (Lucite) base with boundaries constructed from 1/8-in. plastic strips. The well pattern to be studied was outlined with the 1/8-in. plastic strips on the base with narrow apertures (- - 2 mm) in the boundary to represent the wells. Behind each well opening, a rectangular area of some 8 to 12 sq cm was outlined by additional plastic strips. The plastic strips were fastened to the base by any suitable non-conducting cement so that the boundary system was liquid tight. The electrodes were constructed from sheet copper in a fashion that would allow easy removal. In this work, it was found that by simply forming a large U-shaped clip from a strip of the copper that would slip over the boundary was satisfactory and easily removed. The electrodes should be as wide as one of the sides of the rectangular area behind the well opening. If a fractured pattern is studied, fractures inside the well pattern may be represented by strips of copper of the desired shape mounted in some easily removable fashion. The reason that apertures (or salt bridges) were used for wells instead of metallic electrodes is that the plating of the electroactive ion at the cathode and the introduction of an electroactive ion at the anode has a detrimental effect on the swept area outline if these operations \rere permitted to be carried on within the well pattern itself. The anode may be used within the well pattern

Jan 1, 1957

By U. F. Kocks

SINGLE slip and a single parallel array of edge dislocations have been obtained in silicon single crystals by homogeneously bending them in a four-point dead-loading device at 1000°C around the [211] axis with [253.] as the tensile axis which encloses an angle of 40° with the glide plane. Other orientations or lower temperatures proved unsuitable. The homogeneity of the bending was checked by the method shown in Fig. 1. The chemically polished specimen was exposed to parallel light from a microscope-stage lamp. The sharpness of the focus of the reflected light is an approximate measure of the circularity of the sample. This method permitted the determination of the actual radius of bent specimens within 10 pct accuracy. The etching solution developed to show up dislocations consisted of the following volume parts: 2 HF, 1 HNO,, 2 CH,COOH, 1 a solution of 5 wt pct of CuNO, in water (Rosi'). The acetic-acid content was adjusted to produce fine well-defined etch-pits in about 2 min at room temperature. The effectiveness of the etch did not depend on the crystal-lographic orientation of the face etched. The number of etch pits produced after a given deformation was checked in the usual way against the Cahn formula' and showed good agreement. As it is to be expected from the orientation of the primary system there are slip steps on the top and bottom faces but not on the side faces (perpendicular to the bending axis), whereas etch pits appear on the side faces but not on the top and bottom faces. This is different only for occasional dislocations of a secondary glide system. All the micrographs included have been taken in places where the most of secondary glide could be seen. From this it is evident that in the homegeneously deformed region the number of secondary dislocations was less than 1 in 1000 of the primary type. Dislocation Distribution—A series of tests with varying amounts of deformation is shown in Figs. 2(a-c). An observation that can readily be made from these pictures is that the linear density of dislocations within slip lines is relatively constant and independent of the amount of deformation. "Slip line" in this context is understood to mean a line that is a straight connection of individual etch pits. The heavily pitted bands which can be seen in each of these three pictures may be resolved fairly definitely, at higher magnifications, into many "slip lines" the distance between them being of the order of 0.5p The distance between dislocations in slip lines is of the order of 2p and it is also fairly constant in going from the neutral zone outward. The higher over-all dislocation density in the outer regions of any sample and the higher total number in a more heavily deformed sample, are effected by a larger number of "slip lines." The relative constancy of the dislocation distance within an individual slip line is surprising. The absence of pile-ups" may imply, if there is no rear- rangement on unloading," that there are no substantial obstacles to slip in this case. It seems that the equilibrium distribution of the dislocations in each active slip plane under the higher external stress on

Jan 1, 1959

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses. One factor necessary for designing or evaluating a structure's stability is knowledge of the material's mechanical properties, such as stress-strain behavior and fracturing characteristics. The composition of most structural materials such as metals and concrete is uniform and reproducible to the degree that their mechanical properties in service are nearly the same as those measured in the laboratory. Consequently, a rational design can be made on the basis of published mechanical property values. The same equivalence does not exist for rock materials for two reasons: (1) the composition of even the most common rock types is highly variable, and (2) the problem of the size effect is present. Mechanical property tests not conducted at a scale that includes these effects in normal proportion will not be representive of the in-situ rock mass. Of course, the alternative is to perform the test in-situ. Comparatively few mechanical property tests have been performed in-situ because of the physical limitations of test equipment and the prohibitive cost. The current procedure is to design a structure based on small-scale laboratory measurements, with a safety factor usually determined by the experience of the design engineer. While this procedure is somewhat unsatisfactory, laboratory measurements can and do provide a useful basis for the initial design.

Jan 1, 1970

By G. C. Kuczynski

Two particles in mutual contact form a system which is not in thermo-dynamical equilibrium, because its total surface free energy is not a minimum. If such a system is left for a certain period of time, the bonding of the two particles will take place in order to decrease the total surface area, even though the temperature is lower than the melting point. This phenomenon of bonding of two or more particles with the application of heat only and at temperatures below melting point of any component of the system will be called sintering, although the powder metallurgists use this term in a broader sense, including the presence of molten phase and pressure. It is the objective of this paper to study this process and the mechanisms involved in it. This problem is of utmost importance to powder metallurgy and powder ceramics, and its technological aspects have been studied for a good many years. However, the powder metallurgical operations are too complex and include too many superimposing mechanisms, and too many variables for a direct study. It was therefore advisable for the purposes of this study to reduce the variables to a minimum. In this work the radius of the interface formed during bonding in a simple system composed of a spherical particle and a large block of the same metal was studied as a function of time and temperature. It is believed that the mechanism involved in this simple process is fundamental to any sintering operations. Previous Work J. Frenkell was the first to make a serious attempt to develop a theory of sintering. He assumed that the process consists of a slow deformation of crystalline particles under the influence of surface tension which reduces to a viscous flow where the coefficient of viscosity n is related to the self-diffusion coefficient D by the following equation 1 _ D D6kT [1] where 6 is interatomic distance, k the Boltzman constant, and T the absolute temperature. This type of viscous flow of a crystalline substance is essentially different from the ordinary plastic flow. The latter is a specific propcrty of crystals and cannot take place in amorphous bodies. According to Frenkel this viscous type of flow is due to the diffusion of the holes or vacancies arising in the lattice. He was able to derive an equation relating the growth of the interface between two spherical crystalline particles or between a particle and a semi-infinite crystal (Fig 1) to time t at constant temperature. This relationship can be written as follows: x²— 3/2 a/nt [2] where x is the radius of the interface assumed to be circular, a the original radius of the sphere and a surface tension of the material. The other assump- x tions are that x is less than 0.3 and that during the period 1 the original radius, a, of the metallic particle did not change appreciably. A. J. Shaler and J. Wulff2 followed closely the ideas of Frenkel in their theory of sintering of a mass of metallic powder. Neither Frenkel nor Shaler has validated his theoretical speculations with conclusive experimental data. Two measurements reported by

Jan 1, 1950

By J. B. Newkirk, A. H. Geisler

Certain of the permanent magnet alloys provide ideal systems for the study of the kinetics of the precipitation reaction and the correlation of structure with properties. One such system, Cu-Ni-Fe, was found by Bradley1,2 to exhibit a coherent transition state in the precipitation process analogous to that reported for Al-Cu alloys somewhat earlier.3 The attractiveness of some perrnanent magnet alloys for study lies in the fact that vertical sections of the ternary phase diagram in certain regions of composition (Fig I) have as their prototype the binary Ni-Au diagram. Alloys of this type decompose into products that have the same crystal lattice type but only slightly different lattice parameters. The advantages that such alloy systems oA&apos;er for study over the usual in which an intermetallic compound is formed are many: 1. Since the precipitate has the same crystal strutture as the matrix, complex atomic movements are not required to form the new lattice. 2. Similarly, complex orientation relationships are not involved for both the matrix and the precipitate would be ex. petted to have the same orientation. 3, Small &,registry of the decomposition products at equilibrium (in contrast with Cu-Ag alloys) is conducive to extensive coherent growth in the transient state and thus the transition lattice can be detected by the usual X ray diffraction methods. 4. Finally, the relative quantities of precipitate and depleted matrix can be varied from 0 to 100 pet* thus permitting wide freedom for the study of the effect of cornposition on coherent growth and properties. In the Cu-Ni-Fe alloys of appropriate composition, the face-centered cubic precipitate and also the depleted matrix when first formed are coherent with the parent matrix.1&apos;2 The two have the same <Jo parameter as the original matrix but they are both tetragonal; the precipitate has an axial ratio c/a < I while that of the depleted matrix is c/a > I. When coherency is lost they assume the normal face-centered cubic structure with the depleted matrix having a lattice parameter greater than the original matrix and that of the precipitate less. Such a mechanism would also be expected for CU-Ni-CO alloys because of the similarity in constitution but this had not been demonstrated. The Present investigation was conducted on a CU-Ni-CO alloy. The constitution diagram and magnetic properties of these alloys have been fairly well established, however, no previous determinations of mechanism of precipitation and no correlation of structure with properties had been made. Thus, an alloy of this system Was chosen for a comprehensive investiga-

Jan 1, 1949

By J. Kittl, D. Arias

THE decomposition on cooling of the high-temperature ß bcc phases in copper- or silver-based binary systems usually takes place by a martensitic. massive, bainitic, or pearlitic reaction depending upon the particular conditions of each system. The AgAl system is one of these systems in which a massive or a martensitic transformation can occur upon cooling from the 3 phase field. Recently Hawbolt and Brown1 observed both massive and martensitic transformation products in a 22.7 at. pct A1 alloy. In the present work the massive and the martensitic transformations were investigated in a number of alloys for the composition range between 23.2 and 27.9 at. pct Al. The alloys were prepared using high-purity silver, 99.999 pct, supplied by ASARCO and aluminum, 99.999 pct, supplied by ALCOA. The metals were melted using a graphite or a sintered alumina crucible which was sealed in quartz tubes under an argon atmosphere. The alloys Were remelted to reduce segregation and homogenized in the 13 phase field for 24 hr. The weight of the alloys after homo-genization compared with the initial weight indicating the alloy composition to be within k0.1 pct of the in- tended composition. Chemical analysis of several samples confirmed the estimated alloy composition. All metallographic observations were performed on samples electropolished with ac current using a 10 pct solution of KCN and a stainless-steel electrode. The samples were cut into -1-mm-thick slices, polished, heat-treated in the ß phase field, and quenched in air, ice water, or iced brine. Some heat treatments consisted of a 2-min anneal carried out in air to allow maximum quenching speeds. Other samples were heat-treated in a vacuum of 10"4 torr and quenched using a helium blast in a quenching apparatus described elsewhere.&apos; In both cases, no appreciable losses of silver or aluminum were noted at the sample surface by sectioning and electropolishing. Table I summarizes the microstructure resulting from the various quenching treatments. The composition of the alloys investigated is also indicated on the equilibrium diagram in Fig. 1. The <, hcp phase, typical of a massive ß — cm, transformation, was observed in all alloys. A minimum temperature of 450°C was estimated for this transformation based on preliminary cooling experiments. the results being included in Fig. 1. In these

Jan 1, 1970

By N. F. Mott

Jan 1, 1961

By J. B. Berkowitz-Mattuck, R. Hopper, L. Kaufman, E. V. Clougherty

MARNOCH has reported on the attractive high-temperature oxidation resistance of Hf-Ta alloys.&apos; In view of current interest in these alloys, three Hf-Ta alloys were tested in the present study. These included a Hf-27Ta alloy and a Hf-20Ta-2Mo alloy which were supplied by Marquardt Corp. and a Hf-20Ta-Zr alloy provided by Illinois Institute of Technology Research Institute.&apos; The microstructure of these alloys was heated inductively in a glass vacuum system; the oxidizing gas, helium carrier plus a known partial pressure of oxygen (35-102 Torr), was continually passed over the sample at temperature for a given time period. The concentration of oxygen in the gas stream was continuously measured by a differential thermal conductivity technique2 so that the rate of oxygen picked up by the sample could be obtained. The flow rates were 0.1 to 0.2 ft per sec in the vicinity of the specimen. The concentration of oxygen did not fall below 50 pct of the input level in any of the experiments. In several cases a single sample was exposed consecutively at a series of increasing temperature levels. In a second system at ManLabs, cylindrical specimens were exposed to flowing air in a z irconia tube which was heated by radiation from a carbon tube resistance furnace. The specimen was heated from room temperature to the test temperature in flowing argon, then oxidized in air flowing at 0.1 to 0.2 ft per sec. Following exposure, the air was displaced by argon and the specimen was cooled. Postoxidation metallography was performed on every sample. The depth of conversion of the metal matrix to oxide was measured as shown in Fig. 1. The conversion depth was obtained by measuring the oxygen-contaminated metallic zone (which is bounded by a dense outer oxide and a subscale oxide region), subtracting its dimensions from the original dimensions, and dividing by two. Preferential oxidation of

Jan 1, 1968

By Robert B. Fulton, Gill Montgomery

Fluorspar is the commercial name for fluorite, a mineral that is calcium fluoride, CaF2. The name, derived from the Latin word fluere (to flow), refers to its low melting point and its early use in metallurgy as a flux. It is the principal industrial source of the element fluorine. Cryolite, sodium aluminum fluoride, Na3AlF6, is a rare mineral which has been found in commercial quantities only in Greenland. The natural material has been supplanted by synthetic cryolite for its principal industrial use in the manufacture of aluminum. History Fluorspar was used by the early Greeks and Romans for ornamental purposes as vases, drinking cups, and table tops. Various peoples, including the Chinese and the American Indians, carved ornaments and figurines from large crystals. Its usefulness as a flux was known to Agricola in sixteenth century Europe. Fluorspar mining began in England about 1775 and at various places in the United States between 1820 and 1840. Production grew substantially following the development of basic open-hearth steelmaking, wherein it is used as a flux. Use was stimulated by growth of the steel, aluminum, chemical, and ceramic industries, particularly during World Wars I and II. Fluorocarbons entered the picture in 1931. The use of anhydrous hydrogen fluoride (HF) as a catalyst in the manufacture of alkylate for high octane fuel began in 1942. Differential flotation for separating fluorspar from galena, sphalerite, and common gangue minerals in the 1930s, and the application of heavy-media concentrating methods to the treatment of low-grade ores in the 1940s were outstanding technological advances that facilitated increased production. Recently, pelletizing and briquetting of flotation concentrates for use in steel furnaces and the development of flotation schemes for beneficiating ores containing abundant dolomite and barite have been major improvements in the industry. Uses of Fluorspar Fluorspar is used to make hydrogen fluoride, also called hydrofluoric acid, an intermediate for fluorocarbons, aluminum fluoride, and synthetic cryolite. It is used as a flux in the steel and ceramic industries, in iron foundry and ferroalloy practice, and has many minor specialized uses. Hydrogen fluoride (HF) is produced by reacting acid grade (97% CaF2) fluorspar with sulfuric acid in a heated kiln or retort to produce HF gas and calcium sulfate. After purification by scrubbing, condensing, and distillation, the HF is marketed as anhydrous HF, a colorless fuming liquid, or it may be absorbed in water to form the aqueous acid, usually 70% HF. Synthetic cryolite, organic and inorganic fluoride chemicals, and elemental fluorine are made from hydrofluoric acid. The acid itself is important in catalysis in the manufacture of alkylate, which is an ingredient in high-octane fuel for aircraft and automobiles, in steel pickling, enamel stripping, glass etching and polishing, and in various electroplating operations. The manufacture of one ton of virgin aluminum requires about 50 to 60 lb of fluorine content in synthetic cryolite and alumnium fluoride. This quantity, through improved technology and recovery practices, is being lowered significantly.

Jan 1, 1983

By T. B. Armstrong

Electrical energy conservation sees that service facilities are operated only when needed and that production equipment is operated under an optimum condition. Specific energy consumption (kw-hr per tonne) is not regularly recorded for comminution circuits because of variations in ore characteristics and the low grinding efficiency (0.1 to 2.0%) of the equipment. Improved data acquisition can produce meaningful results. Particle size monitor systems and density gauges permit comparison of energy (kw-hr) and production (tonne) for a "fixed" condition. Finding the operating condition producing the lowest unit energy consumption provides a target for an effective energy management program.

Jan 1, 1982

By M. C. Udy, C. H. Lorig

THROUGH the years much interest has been centered in attempting to develop a direct method of iron-ore reduction, to replace or supplement the present indirect blast-furnace process. It would not be difficult to produce a list of more than 500 patents dealing with the direct production of iron and steel, but the few of this type of process that have proved successful do not produce in competition with the blast furnace; they produce special products. A survey of the literature reveals that the equilibrium conditions for the reduction reactions (iron oxides with carbon monoxide and with hydrogen) have been fairly well established but that data on the rate of reaction are discordant, although the general effects of the variables are known. This dissertation deals with the rate of reduction of a magnetite concentrate with hydrogen. The following variables have been studied: bed depth, gas velocity, particle size and temperature. The behavior of a single particle was also studied. LITERATURE Two general factors should he considered in a study of reduction of iron oxide: (1) equilibrium relations, and (2) rate of reaction. The first factor, equilibrium, has received the attention of many investigators and the equilibria Fe3O4-FeO-H2-H2O, Fe304-FeO-CO-CO2, FeO-Fe-H2-H2O, FeO-Fe-CO-CO2 are fairly well established. Of the second factor, the rate of reaction, much less is known. Data are comparatively scarce and there is very little concordance. The discordance probably results from the large number of variables influencing the reactions. However, the general effect of the variables is known. Among these variables are temperature, gas velocity, particle size, porosity, gas composition (distance from equilibrium), presence of impurities, greater or less prevalence of side reactions, and even design of the apparatus itself. Wetherill and Furnas1 published an excellent paper in 1934. They point out that any one or more of five processes (the chemical reaction, diffusion of the reactant through the gas film, diffusion of the reactant through the solid phase, diffusion of the reaction product through the solid phase, or diffusion of the reaction product through the gas film) may be the slow process, and thus the rate-controlling process. It is regretted that the work of these authors was limited to experiments at one temperature, and that the range of gas compositions was limited. Langmuir2 has shown that heterogeneous reactions take place at phase boundaries.

Jan 1, 1942

By Suresh P. Babu, Joseph W. Leonard

The ultimate objectives of comminution should be to reduce material to some specified size while producing a minimum of undersize or fines, with less power, higher throughputs, and with more compact machinery. Attempts to achieve these objectives have been only partially successful, since gains in some areas are achieved at the cost of concessions in other areas. An example of some of these trade-offs can be found in the closed circuit crushing operations of the anthracite and crushed stone industry where, in order to produce a minimum of unprofitable fines, unfavorable concessions must be made in the size of the crushing facility where 2 or more crushing stages are interphased by 2 or more screening operations. This paper discusses experiments with a new process which attempts to achieve some, if not all, of the comminution objectives in a single pass operation without undesirable concessions; or, at the very least, to achieve more than is possible with systems in use today. These objectives are sought by use of water-flushing to enhance comminution. The crushing of coal and other minerals is a mature technology that is long overdue for a careful re-examination. Crushing of coal is generally achieved through the use of rotary breakers and roll crushers. Water-flushing, as envisioned here, appears to have potential application in the following areas: 1) For primary raw coal crushing or for secondary crushing of rotary breaker products. 2) For use as a size reduction and/or concentrating step for crushing coal mine refuse from present production or from existing refuse dumps. 3) For possible future application in underground preparation interphased with continuous mining machinery. Size reduction with conventional methods is known to be an inefficient operation when the increase in surface energy of the material crushed is compared with the input energy. A simple breakdown of the energy consumption in size reduction, given by Orr, is shown in [Fig. 1]. It is believed that most of the energy supplied is lost in the form of interparticle friction.2 Hence, the removal of fines immediately after their formation or the implementation of steps to prevent their formation, based on reduced friction, will reduce the energy requirements of the communition operation.3 A detailed discussion of the mechanism of size reduction is available in other literature.3-5 Even though the closed circuit crushing operation is designed to carry the fines away from the crushing zone, it is still inadequate for instantaneous removal of fines. The present investigation advocates the use of a flowing liquid medium to remove the crushed product immediately after size reduction. Unlike the wet-grinding methods, no constraints are required for the liquid flow rate, and, also, the liquid medium can be used in primary crushers like jaw crushers, hammer mills,

Jan 1, 1978

By Edgar T. Wherry

EDGAR .T. WHERRY,* Washington, D. C. (communication to the Secretary ?).-Dr. Pogue&apos;s presentation of the facts concerning the emerald deposits is very clear and convincing, and the only addition that I can suggest is a summary of previous theories of origin. He makes it evident that the pegmatite theory is the only one capable of explaining the existing relations, but upon certain details there may be some difference of opinion. If I understand the term pneumatolytic, it does not imply that all the elements concerned in a given deposit were transported as gases, but rather that the crystallization of these elements into the various minerals was favored by the presence of certain gaseous substances, notably H20, C02 and HF. It is highly improbable that the oxides of glucinum, aluminum, chromium, and silicon, which enter into the composition of the mineral emerald could have been transported in the gaseous form. The same is true of the metallic constituents of the parisite and other associated minerals. The explanation suggested, that solutions separated into liquid and gaseous portions, the latter ascending and forming the emerald in the upper portions of the rock only, therefore, seems to me untenable. When two formations exist side by side and one, A, is mineralized while the other, B, is barren, the possible explanations may he classed as (1) chemical, and (2) physical. 1. Some chemical feature of A not found in B might have caused crystallization of certain minerals in the former, which did not appear in the latter. In the present instance both rocks appear to be so similar chemically that no such effect can be looked for. Pogue mentions carbon as a possible precipitating agent, but describes both formations as carbonaceous, so that the difference in the minerals of the two can not be thus explained.

Jan 10, 1916

By Henry Gross

RECENTLY, areas of abnormal rock pressure have been drilled on the Gulf Coast of the United States. These pressures may be caused by the recent and pronounced raising of some of the structures without loss of the formation pressure that existed when the reservoir was developing and the producing sand much more deeply buried. It is possible also that a permeable fissure may connect a shallow accumulation of gas with the gas cap of a much deeper reservoir of oil, gas and water. The pressures are so great that dependence on blowout-prevention equipment alone is hazardous to life and property. Fortunately, wells with excessive casing-head pressures, such as the Stanolind Oates No. 1 of the South Houston field, an 8700-ft. gas well with 6000 lb. per sq. in., and the near-by Stanolind Candelari No. 1, and 8100-ft. gas well with 5000 lb. per sq. in., have not blown out and cratered. A case is on record of drill pipe in a, well in Harris County, Texas, (Oates No. 1) rotating for 8 hr. through blowout-prevention rants holding a back pressure of 2900 1b. per sq. in. at the casinghead after the mud was altered by salt-water intrusion. Such conditions warrant the use of extremely heavy muds having low viscosity, made from galena (PbS) or specially prepared mixtures of hematite (Fe203) and galena suspended by bentonite. In some Gulf Coast wells, sodium silicate mixed with concentrated brine is used to drill through heaving shale formations. Such a fluid inhibits heaving remarkably, but it is expensive and costs as much as $10 per barrel. Barite has been used to weight this mixture. However, this mineral too rapidly increased an already excessive viscosity and it was thought that galena might be better for weighting such drilling fluid. The operator was anxious to try the latter, but none was available in the district.

Jan 1, 1938

The following list comprises the names of those persons who became members during the period May 10, 1916, to June 10, 1916: ARCHIBALD, JOHN CHRISTIE, Min. Engr., Supt. of Cyanide Plant, Guanajuato Reduction Mines, Guanajuato, Mex. BRUNEL, FRANK P., Cons. Min. Engr Mitchell & Brunel, Ajo, Ariz. CALVERT, WILLIAM ROBERT, Cons. Geol. ...225 Kearns Bldg., Salt Lake City, Utah. CHAMPION, J. R., Supt The Yak Mining, Milling & Tunnel Co., Leadville, Colo. CHARLES, LAVERN JOHN, Construction Engr., Elephant Butte Dam, Elephant Butte, N. M. CHASTEL, ANDRE, Min. Engr., Societe Miniere & Metallurgique de Penarroya, 12, Place Vendome, Paris, France. CHRISTIE, WALLACE H., Vice-Pres. and Mgr., Alt. Bert Gold Dredging Co., 604 Mission St., San Francisco, Cal. CLARK, RONALD ..Hardinge Conical Mill Co., 120 Broadway, New York, N. Y.

Jan 7, 1916

By J. R. Low, D. F. Stein

Single crystals of iron have been grown from three different lots of Ferrovac "E" of somewhat different chemical composition by the strain anneal technique. Using a technique to seed the crystal similar to Dunn&apos;s for silicon-iron, it has been possible to orient the crystals grown in both direction and plane of growth. Crystals having the plane of the strip oriented (100) , (110), (111), (112), (123), and (491) have been grown. The growth directions used have been [100], [110], 45 deg from a [110}, and various others of no specific crystal orientation. The usual dimensions of the crystals were 8 by 1 by 0.08 in. Attempts to grow crystals were about 90 pct successful. METHODS of growing single crystals of high purity iron have been reported in the literature.1-4 However, each of these methods was not completely reliable when used on materials having slightly different chemical composition and in some instances a small number of successes were obtained using identical materials. Except for the method used by S. Dohi and T. Yamoshita,1 it has not been possible to reorient single crystals of high purity iron to give any desired orientation. The method to be described has made it possible to grow single crystals from three different lots of material having different compositions, and to orient the crystals with respect to growth direction and surface. STARTING MATERIAL The material used during this investigation was a vacuum melted high purity iron marketed by the Vacuum Metals Corporation designated Ferrovac "E." Three lots of Ferrovac "E" having the following composition were used with equal success: The compositions listed are those of the as-received material; and they may have been modified before the growth of single crystals. Analysis of heat B just before growth and after growth revealed that the heat treatment prior to growth did not change the carbon content, but the oxygen content was changed from 0.0092 pct to 0.0034 pct and the nitrogen content from 0.0003 pct to 0.0001 pct. After growth of the single crystals, the carbon had dropped to 0.001 pct. None of the heat treatments would be expected to change any of the other impurities very markedly. Heat C would be expected to have a metallic impurity content similar to heats A and B. PROCEDURE Ferrovac "E" iron which had been obtained in bar form having a diameter of about 1 in. was rolled into strip for growing single crystals. By passing the 1-in. bar through a cold rolling mill several times, it was reduced to a strip 0.15 in. thick. The strips obtained were then cut into suitable lengths for heat treating (about 9 in. long), annealed at 925°C for 2 hr in dry hydrogen and water quenched. It was then necessary to bake the strip at 200°C for 24 hr in air in order to prevent cracking during further rolling operations. While it was possible to cold roll the 1-in. bar directly to the desired 0.080-in. strip, the intermediate anneal was used because the strip so obtained produced better single crystals. The strip obtained by rolling the 1 -in. bar directly to 0.080-in. strip produced single crystals having a large number of occluded grains. Experiments showed that the optimum reduction in area by rolling prior to the growth of single crystals was about 50 pct. Attempts to grow single crystals from material that had been reduced less than 40 pct were unsuccessful presumably because the matrix did not possess the critical amount of texture necessary for growth. The strip obtained after the rolling operations had very irregular edges which were ground to give a strip with uniform dimensions. The strip was then annealed at 825°C for 3 hr in hydrogen and furnace cooled. Fig. 1 illustrates the grain size obtained. A temperature of 940°C was used for the annealing temperature on one group of strips

Jan 1, 1962

By R. B. Rosene, G. L. Foster, A. R. Hendrickson

he properties of some of the common fracturing oils, such as sand-falling rate, fluid loss and viscasity, are a function of the three major constituents of the oil. These are: asphaltic material, parafin waxes and a base oil. The base oil can be either high or low viscosity. Asphaltic material increases viscosity by thickening the oil, decreasing the rate of fall of sand through the oil. at temperatures up to 200" F. When large arnorrnts of parafin wax are present, much of the wax i.s not dissolved, but is present in the form of rnicroscopic crystals. 7&apos;his, of course is limited to temperatures below the melting points of waxe.s. As a result, parafin waxes clo not function primarily as thickener.7, but rother as bullting materials. The functiori of wax, without asphaltic material, in a low viscosity base oil is uniquely unlike that of wax with asphalt coexistent in the oil. The resulting difierence in wax crystal size governs the sand-falling rate to a large extent. An ideal type of fracturing oil is one containing neither asphalt nor waxes. In such cases, the viscosity and resulting low sand-falling rate are apparently due to soluble resin- ous hydrocarbons, which are compatible with formation oils. INTRODUCTION Since the introduction of hydraulic fracturing as a method of stimulating production from oil and gas wells, a variety of fluids have been employed to open the fractures and carry the propping agent. Such fluids include gels, emulsions, and oils. In the latter category, the use of refined oils has increased tremendously, and it is probably safe to assume that such oils represent more than one-half of the total fluid used in fracturing. The general acceptance of refined oils for fracturing can be accounted for on the basis of their relatively low cost and general applicability. To minimize transportation costs, such refined oils are generally obtained within the local areas of operation. As a result there are several kinds of oil used in different areas, with a wide variation in the basic composition. These types may vary from a fair grade of lubricating stock to a highly viscous cut-back asphalt. or road oil. Originally, little attention was paid to the composition of the oils used for fracturing, and any oil which would carry sand was considered satisfactory. Recently, however, service companies and well operators have become more concerned with the type of oils used for fracturing. With this in mind, the present work was undertaken to evaluate and compare many widely used fracturing oils to determine which constituents were most desirable for fracturing purposes. Some of the important properties of fracturing fluids are sand-falling rate, viscosity, and fluid loss. Other properties, that are actually of no less importance, include flash point, pour point, emulsifying tendencies with formation brines, and compatability with the formation oils. This discussion has been limited, however, to the first mentioned properties in order to give some idea of the general composition of the refined oils, how they function, and why. PROPERTIES OF FRACTURING OILS The properties of fracturing oils are a function of the three major constituents of the oil. These may be designated as: (1) asphaltic material, (2) paraffin waxes and (3) a base oil, which may be of either high or low viscosity. The asphaltic material clas-

Jan 1, 1956

IN the decade beginning 1850, the development by William Kelly in I the U.S.A. and Henry Bessemer in England of the pneumatic method of refining pig iron, known as the Bessemer process, gave the world the first method of producing low-cost steel in large volumes. Briefly, the Bessemer process consists of blowing air through liquid blast furnace iron in a refractory-lined vessel known as a converter. The air enters the iron in the furnace bottom through tuyeres, and during its passage through the iron removes the carbon, manganese, and silicon by oxidation. The heat produced by oxidation is sufficient to raise the temperature of the liquid metal to normal steel casting temperatures and, in addition, to melt some scrap. In the 1860&apos;s, the open hearth process was introduced which in the early part of the twentieth century surpassed the Bessemer process in steel production. In the early 1870&apos;s, Thomas and Gilchrist discovered that phosphorus could also be removed if lime were added and the converter lined with basic refractory; the modification is known as the basic Bessemer process and is used in Europe. Bessemer steel usually contains between 0.010 and 0.020 per cent nitrogen and between 0.05 and 0.10 per cent phosphorus which influences the properties. Henry Bessemer,1 in 1856, recognized the possibility of using oxygen in the converter process, but the cost was prohibitive. This interest was associated with the theoretical balance of the Bessemer process. Experimental work&apos; has indicated that bottom blowing with pure oxygen results in serious converter bottom and tuyere erosion. Dilution of the oxygen by steam has been observed to be an effective means of maintaining low-nitrogen content of the steel and at the same time reducing bottom and tuyere erosion. A further advantage is that the fume emission characteristic of Bessmer operation is reduced. The addition of steam to the oxygen, however, reduces scrap-melting capacity due to the endothermic reaction characteristics of steam. The possible advantages of refining methods for steel using high-purity oxygen have been recognized for over a hundred years, but the develop-

Jan 1, 1964