Search Documents

Harrison W. Craver, Director The Library of the above-named Societies is open from 9 A.M. to 10 P.M., except on holidays. It contains about 70,000 volumes and 90,000 pamphlets, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend a portion of their time in localities isolated from sources of information. To these the Library, through its Library Service Bureau, can render valuable service through correspondence; letters requesting information will receive especial attention. The Library is prepared to furnish references and photographic copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information on the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape.

Jan 5, 1917

By G. R. Frank, R. E. Willett, E. H. Hollingsworth

The most generally accepted equilibrium diagram for A1-Fe alloys has a eutectic system on the aluminum side with an essentially insoluble constituent of the formula, FeAl,, as the second phase. In 1938, Bradley and Taylor1 did report a phase change of FeAl,, but this change has never been confirmed. According to them, FeA1, is the stable phase only at higher temperatures; at lower temperatures, it is converted into Fe2Al7 and aluminum. It has now been found that there is, in fact, a phase change of the Al-Fe constituent on the aluminum side of the equilibrium diagram. This change, however, is not the one reported by Bradley and Taylor. The alloys used were cast by continuous processes and had these analyses: Fe - 1.98 to 2.02 pct, Cu-0.01 pct, Si - 0.01 pct, Mn - 0.01 pct, Mg - 0.00 pct, Zn - 0.00 to 0.01 pct, Cr - 0.00 pet, Ti - 0.00 to 0.04 pct. The constituent in these alloys was identified by X-ray analysis with a Guinier camera and by chemical and X-ray powder diffraction analyses. Two procedures were used to separate constituent for the last two analyses. In one procedure, it was separated by treating a sample with a solution of methanol saturated with iodine. And in the other procedure, it was separated by first applying, at 12 amp per sq ft in 15 pct sulfuric acid at 70°F, an oxide coating to a sample, and then dissolving this coating in a solution of 35 ml of 85 pct H3PO4 and 20 g of CrO3 per liter. Several observations directed attention to a phase change of the A1-Fe constituent. Differences that appeared too great to be accounted for by micro-structure alone were found in the voltages required to apply the same thickness of an oxide coating to products from rapidly and slowly chilled ingot. Even more striking was the difference in appearance of the coatings themselves. One applied to a product from a rapidly chilled ingot was dark gray in appearance, in fact, almost black, while one applied to a product from a slowly chilled ingot was essentially white. Also, even a short period of thermal treatment at an elevated temperature of products from rapidly chilled ingot led to the same anodizing behavior as that of products from slowly chilled in-

Jan 1, 1962

By J. J. Rutledge

FULLY 60 per cent of the serious and fatal accidents in Maryland coal mines are due to falls of roof and side. Usually, the victim of the fall sustains a broken back, sometimes not only the vertebrae being fractured but the spinal cord also being severed. When the spinal cord has not been severed and yet the vertebrae have been broken or injured, it is often possible to rehabilitate the victim of the broken back. - Such accidents are classed as Permanent Total and the victim receives a certain compensation from the State Industrial Accident Commission; sometimes the amount is awarded in a lump sum, but usually it is paid weekly. When the amount allotted to the victim of such an accident has been expended, either in a lump sum or weekly payments, the victim of the accident is dependent on public charity. Some efforts have been made to physically rehabilitate the victims and make them at least partly self-supporting before the expiration of their compensation payments. The State Industrial Accident Com-mission has done some of this rehabilitation. The Maryland Bureau of Mines, in cooperation with R. C. Thompson, Supervisor of Vocational Rehabilitation, State Department of Education, and his assistants, has, through an informal cooperative arrangement, placed several of the victims in hospitals in Baltimore for treatment. Six years ago, through the efforts of the Maryland Bureau of Mines, a dozen or more broken-back victims were examined by an orthopedic surgeon and report was made to the Bureau regarding such cases and the possibility of their rehabilitation. This paper details the result of such examinations.

Jan 1, 1936

By R. H. Richards

In October, 1891,I read a paper before the Institute on a "A HandTelescope for Stadia-Work" (Bans., xx., 732), and promised to report at an early date some results showing the degree of accuracy attained with the instrument. I am now able to report on these results and also on certain improvements that I have made in the target since the first paper was read. I may say that I prefer the title, "Prismatic Stadia-Telescope," to that used in my earlier paper, for while the instrument can be used with perfect satisfaction for short sights up to, say, 300 to 600 feet when held in the hand, it is impossible to read milch longer distances without the use of a tripod, as a steady support for the instrument. Results are here given upon four combinations of prism and telescope. No. 1. A telescope made by Alvan Clark & Sons, 3-inch objective, 28 inches focal length, magnifying 60 diameters, the prism covering half the objective: Feet measured Reading of Distance reduced Reeding of rod pro by tape. the rod. to feet. portional to 100 ft. 127.66 1.1825 100 .92629 211.35 1.9585 100 .92666 326.59 3.0265 100 .92669 484.88 4.4925 100 ,92652 606.91 5.6225 100 .92641 Average,,92651 The value of this prism therefore is .92651 feet on the rod for 100 feet of distance, or 1 foot on the rod corresponds to 107.931 feet of distance. No. 2. A Bardou telescope having a 1-inch objective, magnifying 20 diameters, and a prism covering half the objective:

Jan 1, 1893

By M. T. Melvin, N. P. Kripakov

The practical application of a post-processing modeling procedure to simulate progressive rock failure around the periphery of coal mine entries is presented. This numerical scheme utilizes a simple rock model that incorporates easily obtainable input parameters consistent with basic rock mechanics principles. These parameters include the cohesion, angle of internal friction, modulus of elasticity, and Poisson's ratio of the bedded deposits that comprise the imediate roof, coal seam, and immediate floor. The geometry of the entry, along with the in situ stresses existing at a mine site prior to mining, are also considered in the analysis. The potential of this procedure as a predictive tool in determining the extent of pillar rib fracturing and yielding of the immediate roof and floor is evaluated assuming a Mohr- Coulomb failure criterion. The procedure is designed to be user oriented and is adaptable to any finite element code with linear elastic capability, making it particularly attractive to users with limited budgets and computer size.

Jan 1, 1983

[Admissions: H. J. Gruy, Chairman Kenneth W. Robbins W. Frank West Aurel E. Smith R. F. Madera Tom G. Calhoun Kenneth F. Anderson B. M. Goltlieb Advertising: Clark R. Edgecomb, Chairman Bernard F. Klein. Henry N. Lyle R. E. Howard H. M. Krause, Jr. Education: R. L. Whiting, Chairman John M. -Campbell E. T. Guerrero Don D. Little J. C. McCarthy Frank G. Miller Douglas Ragland H. C. Slider R. L. Slobod]

Jan 1, 1961

By John E. Willson, Ben L. Seegmiller

A portable electronic instrument was designed and constructed to detect unknown stress magnitudes in rocks. The principle used to detect stress is based on the propagation velocity method. This method allows the stress in a rock subjected to a load of unknown magnitude to be determined, provided that the wave velocity-stress relationship for similar rock is known. This is accomplished by measuring the travel time of longitudinal mechanical waves passing between two points a set distance apart in a rock. The velocity of the wave is calculated and the stress determined from the wave velocity-stress relationship. If the sending and receiving transducer spacing is constant, a time vs. stress relationship rather than the velocity-stress relationship may be used. The method is nondestructive and tests can be made without drilling or otherwise disturbing the rocks. The first studies undertaken in the United States to determine stress in rocks using propagation velocity techniques were reported by Obert1,2 in 1939 and 1940. The Soviet Union first reported using propagation methods to study rock pressures in 1951.8 Success of the method led to the development of a pulse-type ultrasonic seismoscope4 in 1953. Using this instrument, Ivanov and Betaneli5,6 in 1963 succeeded in devising and testing under field conditions a method of investigating coal pillar stresses. In 1967 Osipova7 reported results of similar studies in the Nakhichevan salt mines. In France, Tincelin8 has used the propagation velocity method to study the stress distribution in iron ore pillars. Uhlmann9 has investigated stresses in salt and potash pillars in Germany, using velocity techniques. Determination of uniaxial stress by propagation velocity methods is limited to rocks which have readily detectable wave velocity-stress variations. The present stress detection instrument is restricted in application to rocks which have a velocity change under stress of at least 300 fps. Examples of rocks which meet this requirement are sandstones, coal, and possibly some limestones. Testing of this instrument was limited to a laboratory study and the results may or may not be indicative of what would be found in a field test. A program of field experiments to study the feasibility of using this instrument to determine mine pillar and tunnel stresses is in progress. Instrument Design The instrument has two main components: A probe and a control-display unit. The probe is a hand-held device to which two identical rodlike transducers are rigidly mounted. Coaxial cable connects the probe to the control-display unit which is mounted in an enclosed carrying case measuring 7 % x 9 x 13 in. The instrument is designed so it may be carried and operated by one man. Weight of the probe and enclosed control-display unit is approximately 20.1b. The probe consists of two transducers identical in construction. One transducer is used to convert electronic pulses to mechanical waves and transmit these waves into a rock. The other detects the transmitted waves in the rock and converts them back into electronic signals. The basic element in both transducers is a piezoelectric crystal. The crystal is a disk made of lead titanate zirconate and has a natural resonant frequency of 400 kHz ±1% in the thickness mode. A schematic of one of the two identical transducing elements is shown in [Fig. 1.] A spacing of 6 in. between sending and receiving transducers has been found to be most satisfactory. The control-display unit consists of a pulse generator and a 1-in. oscilloscope. Various electronic devices are used for the power supply, amplification, and calibration. The amplitude of the square wave from the pulse generator can be continuously varied between 0 and +20 vdc. Pulse width can be set at 1, 2, 3, or 4 µsec. The repetition rate of the pulse can have the following values: 50, 75, 100, 150, 200, 250, 300, 400, 500, 750, and 1000 Hz. The oscilloscope delay system allows the travel time of the longitudinal wave passing through a rock to be measured to an accuracy ±0.1 µsec in the range from 0 to 995 µsec. Fig. 2 is a schematic of the various electronic sections in the control-display unit. Laboratory Testing The first step in using the instrument is to develop a velocity-stress or a time-stress curve for the par-

Jan 1, 1972

By Philip J. Shenon

IN 1947 the mining industry strove desperately to regain operating normalcy. During the first part of the year the industry in this country was plagued with labor shortages, strikes, and portal-to-portal lawsuits. Then followed the uncertainty of Government policy with respect to subsidies and tariffs; and the long and bitter controversy as to whether we are a nation of mineral "haves" or "have-nots." As the year progressed the labor supply impoved somewhat and the Taft-Hartley law brought partial relief to strike-troubled industry. The uncertainty with respect to tariffs was partly answered by President Truman on April 29 when he announced the suspension of the 4¢ import duty on copper until March 31, 1949, and later, near the close of the year, by the announcement of the tariff agreement signed by the United Nations at Geneva. By this agreement tariff rates are to be adjusted downward, or "bound" at their present levels, for three years, on commodities amounting to some 60 per cent of United States trade. Effective Jan. 1, 1948 the rate of duty will be substantially reduced on ores, concentrates, or metals of zinc, aluminum, copper, manganese, tungsten, iron, steel, barytes, nickel, cadmium, and antimony.

Jan 1, 1948

By Ralph A. Sherman

In these days of intense competition for the domestic fuel market much is heard of the low efficiencies with which solid fuels, and most particularly bituminous coal, are burned in domestic heating equipment. In contrast to the every-day operating efficiencies of 85 and 90 per cent in large, central, electric-generating stations, efficiencies of 50 per cent and lower are cited for the hand-fired home furnace. Just as the miles per gallon of gasoline is only one of the factors that determine the cost of operation of an automobile, so the thermal efficiency is only one factor in the cost of domestic or other heating. The purpose of this paper is to analyze the total costs of domestic heating by various fuels and types of equipment, to determine the relative importance of efficiency and other factors, and to discuss what this signifies relative to the future of the use of fuels in the home. Factors That Govern the Choice of Fuel and Burning Equipment A rational, intelligent selection of fuel and equipment for heating the home would consider two groups of factors: Cost Factors Convenience Factors 1. Cost of potential heat in fuel 1. Attention 2. Efficiency of combustion and heat transfer 2. Dirt 3. Fixed charges 3. Noise a. Interest b. Depreciation c. Repairs 4. Power costs 5. Cost of handling ash and refuse. As just stated, the purpose of this paper is to analyze the relative importance of the five cost factors and not to discuss particularly the relative total costs of different methods of heating. However, to arrive at the percentage costs and to show clearly how they were determined, a statement of the total costs is unavoidable. One example only will

Jan 1, 1934

By William E. Ford, Edward Salisbury Dana

The Nitrates being largely soluble in water play but an unimportant r81e i~ Mineralogy. SODA NITER. Rhombohedral. Axis c = 0.8276; rr" 1071 A 7101 = 73' 30'. Homeo- morphous with calcite. Usually massive form, as an incrustation or in beds. Cleavage: r (1011) perfect. Fracture conchoidal, seldom observable. Rather sectile. H. = 1.5-2. G. = 2'262.29. Luster vitreous. Color white; also reddish brown, gray and lemon-yellow. Transparent. Taste cooling. Optically -. w = 1'5874, e = 1'3361. Camp. - Sodium nitrate, NaN03 = Nitrogen pentoxide 63'5, soda 36'5 = 100.

Jan 1, 1922

By E. H. Jr. Dix

THE success of the Charpy impact test in the steel industry has led those interested in aluminum alloys to investigate the possible applica¬tion of this test to aluminum and its alloys. In this paper are set forth the results of a few preliminary tests made at the Lynite Laboratories of the Aluminum Manufactures, Inc. In order to study more thor-oughly the significance of the Charpy test, slow-bending tests have been made duplicating the arrangement of the impact machine. Tests have been made on both notched and unnotched specimens of a series of copper-aluminum alloys. APPARATUS The standard American-made Charpy impact machine delivering a blow of over 200 ft.-lb. was- much too large to test aluminum-alloy specimens of the same type used for steel, so that it was necessary either to adopt a larger specimen or to have a special light-weight hammer made. Since there is no known relation between specimens of different sizes, even though geometrically similar, it was decided to adhere to the 10 by 10 mm. specimen. Accordingly, Sauveur and Boylston, the American makers of the machine, were asked to construct a special light-weight pendulum adapted to their standard machine, this pendulum to have one-tenth the capacity of the standard. The writer wishes here to acknowledge his indebtedness to Mr. H. M. Boylston for the personal interest and care exercised in constructing this pendulum. The machine with, the light-weight hammer in place is shown in Fig. 1. It is mounted on a concrete foundation with the concrete covering the flange on the base of the machine. Vibration is further prevented by four 5/8 -in. (15.8 mm.) foundation bolts. The large standard hammer shown against the wall was also used for some of the unnotched bars that requited more than 20 ft.-lb. to rupture.

Jan 4, 1920

By H. I. Ashby

INITIAL development of the south orebody at San Manuel is being carried out from the No. 1 and No. 2 shafts. The haulage and grizzly levels are being driven to develop the upper one third of the massive hydrothermally altered and fractured monzonite orebody. This first haulage level has been placed at the 1475-ft level with a grizzly level 60 ft above. The grizzly level will be connected to all service shafts so that men and supplies can come down to the grizzly level and go to working places without congesting the haulage level. These connections are also a vital part of the ventilation plan. The haulage level is being advanced along the north and south fringes of the orebody and connections are being driven to the three shafts now under construction. The No. 1 and No. 2 shafts will serve the development work with supplies, skip hoisting, and ventilation at each shaft and the two shafts are connected on both the grizzly and haulage level.

Jan 7, 1954

By Carl H. Beal

DURING the latter part of 1915 and the first half of 1916, the writer held the position of geologist in connection with the conservation work instituted by the U. S. Bureau of Mines, on oil and gas land belonging to the Indians of the Five Civilized Tribes in Oklahoma. The duty of the geologist was to correlate formations containing oil, gas, and water, and to determine the relations of these substances in the different formations so that the conservation agents might carry on their work most intelligently. On account of the rapid development of the Cushing field, which lies in the western part of the Creek Nation, much work was done there by the inspection force. In the course of the geologic studies a large amount of information was collected, which, on analysis, has disclosed some interesting facts worthy of publication. The report, of which the following remarks are an abstract, has been prepared and submitted to the U. S. Geological Survey for publication. This report is now (June, 1917) in the press and will doubtless be issued in a few weeks. Methods Used In addition to the structure maps showing the folding of the Pawhuska limestone, which crops out in several places in the Cushing field, separate structure maps of the three most important productive sands—the Lay-ton (Fig. 2)) Wheeler, and Bartlesville—have been prepared. These structure maps were prepared by obtaining the logs of nearly all the wells

Jan 1, 1918

By Roshan B. Bhappu, Ronald J. Roman, Dexter H. Reynolds

The reaction between manganese dioxide and molybdenite in a water- sulfuric acid medium was studied at atmospheric pressure and from 25° to 103°C. Both solids are dissolved to give, as final products in solution, Mo(VI), S(VI), and Mn(II). Stoichiornetric relationshifis are most simply represented by the equation MoSz + YMnO2 + 15H+ - HMoO-4 + 2HSO-4 + 9Mn++ + 6H20 The rate of this reaction was found to be dependent on temperature, manganese sulfate concentration, acid concentration, and, in a complex way, the surface areas of both manganese dioxide and molybdenite. Both the total amount of manganese dioxide and tnolybdenite and the ratio of manganese dioxide to molybdenite played a part in determining the over-all rate of the reaction. The effect of acid concentration on the rate was also dependent on the ratio of manganese dioxide to molybdenite. SEVERAL reports in the literature describe reactions using manganese dioxide in water-sulfuric acid media as an oxidizing agent. Nearly all previous work describes interactions between an ion and manganese dioxide, such as the oxidation of ferrous to ferric iron,' or the interaction between a molecule in solution and manganese dioxide, such as the oxidation of toluene to benzaldehyde.2 Only a few references describe the use of solid manganese dioxide to oxidize another solid in sulfuric acid. One report3 states, "Manganese dioxide in dilute sulfuric acid solutions had no beneficial effect (in leaching copper from chalcopyrite), but in more concentrated acid solutions the rate of solution was about the same as that for permanganate." In 1902 a German patent4 described a process which used manganese dioxide in strong (50°Be') sulfuric acid for oxidizing chromite ores to soluble iron and chromium salts. The process consisted of mixing the sulfuric acid with the finely ground ore and manganese dioxide. The pulp was then heated to about 120°C and an electric current passed through it. The manganese dioxide apparently dissolved in the strong, hot acid solution, oxidized the iron and chromium and itself was reduced to manganese 11! then was oxidized at the anode back to manganese dioxide, and the cycle repeated. An extensive study5 of the kinetics of the oxidation of pyrite with manganese dioxide indicated that in dilute sulfuric acid solutions (about 0.1 N) and at elevated pressures the dissolution of the pyrite was brought about by air oxidation of the iron to ferrous sulfate, followed by manganese dioxide oxidation of the ferrous sulfate to ferric sulfate. The mechanism proposed by the authors involved the oxidation of the iron at the surface of the manganese dioxide. Also! the oxidation of sulfide sulfur to sulfate was credited to the oxygen in the air, not to the manganese dioxide. Since the metallurgical literature is lacking in information concerning the use of one solid to oxidize another solid. the current investigation was under-

Jan 1, 1965

By J. Marshall Downey

The most fortunately situated U. S. potash producer-whether in New Mexico, California, or Utah--once simply took from the ground a mixture of sodium chloride and potassium chloride, crushed it to a maximum of 10 mesh, and separated the two salts by physical methods. He piled the sodium chloride on the desert and sold the potassium chloride to fertilizer mixing companies. Seven companies in the Carlsbad basin of New Mexico now use at least three basic processes for making the separation and at least three more processes have been or are under investigation. In addition, two companies outside the basin use two methods for taking KC1 from natural brines

Jan 12, 1958

By A. R. Rosenfield, G. T. Hahn

The effects of adding 0.025 volume fraction of uniformly dispersed Tho2, particles (particle size -380A) to iron have been examined. The two-phase alloy is shown to have a lower transition temperature and higher cleavage stress than either the base metal or a solid-solution alloy (Fe-3Si). Enhanced cleavage resistance is thought to be a consequence of particles limiting the effective slip distance of dislocations and thus the ability of Pile-ups to act as stress concentrations. Further calculations predict that the highest cleavage strengths are attained with uniform dispersions, where the particle size is kept small (-250A) and the volume fraction is relatively large (-2 to 3 pct). ALTHOUGH a fine dispersion of second-phase particles is known to impart strength to an alloy, the possibility that it might also impart ductility has only recently been explored. Outstanding progress has been made in the production of ductile tungsten alloys containing Tho21,2or (Hf, Zr)C,= but the contribution of the dispersion to ductility has neither been optimized nor fully analyzed. The basis for such an analysis has now been developed1,5 and is discussed briefly below. Experiments on iron are also described that attempt to isolate one of the possible ductilizing mechanisms and test its effectiveness. In analyzing these experiments, it is important to remember that cleavage obeys a stress criterion, and that either a lower ductile-to-brittle transition temperature or a higher cleavage stress is evidence of enhanced resistance to cleavage. DUCTILIZING MECHANISMS Slip Blockage. Cleavage fracture of polycrystals may be initiated at the intersection of a slip band (or twin) and a neighboring grain or a large (-1 to 5 µ) particle. The slip band generates a stress concentration at its head, and either the grain boundary fractures, the particle fractures, or cleavage is initiated in a neighboring grain. Experimental evidence for this viewpoint is found in metallographic studies8-8 and from the observation that cleavage is usually preceded by yielding.8-11 The potency of a slip band as a stress concentrator

Jan 1, 1968

By C. G. Dunn

This note describes a method for revealing micro-structures in tantalum through an {hkl} effect which was found during a study involving amorphous and crystalline tantalum oxides. Three steps are involved. First, an amorphous film of Ta2O5 is formed anodically1 on the surfaces of the tantalum. The amount needed depents on the thickness of the substrate tantalum; 1600Å of oxide, however, is generally satisfactory in the 1/2 -mil (12 µ) to 3-mil thickness range. The film at this point is uniform in color. Second, the anodized specimen is heated to 800°C in. vacuo during a period of a few minutes and held at temperature for 5 min. During such a treatment some oxygen leaves the oxide through dissolution into the substrate tantalum (e.g., at 10-8 Torr oxide films thinner than about 800 completely disappear on 5-mil strip). Considerable crystallization of the amorphous oxide also occurs adjacent to the metal/oxide interface but not throughout the oxide thickness. The thickness of oxide needed as a residue is not too critical; values between 500 and 1000Å (optical estimate') may be most useful. (The presence of a residual oxide layer after the heat treatment usually is not apparent; in fact, in most instances the surfaces have a metallic appearance. This can be the case also for thicker residual films needed in the detection of a crystalline oxide phase by surface X-ray diffraction—e.g., if the initial oxide film is 3000Å thick, enough crystalline oxide is formed for X-ray detection.) The third step eliminates the metallic appearance at the surface and reveals (or produces) a varied colored film of tantalum oxide. Two methods can be used and both will be illustrated. If the specimen is dipped in 48 pct HF for a few seconds, the tantalum is found to be covered with a multicolored oxide. Moreover the colors correlate with the grain structure of the substrate tantalum through an orientation dependence of the type illustrated in Fig. 1, where results of an orientation analysis by the Laue X-ray method have been plotted. Other film conditions would have provided a different set of colors for the same orientations. Any such correlation, however, provides a basis for a qualitative assessment of the distribution of orientations in a large sample. The cold-rolled structure of tantalum foil produced by a recrystallization anneal and a cold-rolling reduction of 95 pct is not easily obtained by usual metal-lographic methods.' The structure, however, is easily revealed by the present technique, Fig. 2. The alternative third step is to reanodize the specimen. The optical nature of the final anodic film depends on the presence of the crystalline oxide phase; color variations indicate optical thickness variations in the film. As the reanodization voltage is increased from zero, straw and light brown colors appear (as usual), followed now by variations in color from grain to grain depending on {hkl} orientation. Suitable end points, which are determined by voltage and time, are easily established. Fig. 3, for example, shows the grain structure developed in 5-mil tantalum strip during a 30-min re-crystallization and grap-growth anneal at 1800°C. An anodic film of 1600Å thickness was added prior to the special 800°C anneal. Reanodization was done at constant current density (near 0.2 ma per sq cm) in an aqueous solution of H3PO4 (0.01 pct) and was terminated after the initial brown colors were replaced by a deep blue at approximately 30 v. Although good grain contrast can be obtained with bright field illumination, even greater contrast for black and white micrographs may be obtained with polarized light, as in Fig. 3.

Jan 1, 1967

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Walter Kauenhowen

The crude-oil production of Germany without Austria during 1938 amounted to 3,864,518 bbl., representing an increase of 21.7 per cent over the 3,173,373 bbl. produced in 1937. Adding the Austrian production, the crude-oil production of the new German Reich totaled 4,259,717 bbl. during 1938, representing an increase of 25.3 per cent compared with the respective figures of the previous year. According to published official data, and using a conversion factor of 1 metric ton equaling 7 bbl., the oil production of Germany in 1938 was as shown in Table 1. A semiofficial publication1 states that the program of the crude-oil industry for the second year (1938) of the four-year plan was successfully accomplished. According to the same source, new drilling developments at the following localities were promising: Reitbrook near Hamburg, Heide in Holstein, Eicklingen-Sandlingen near Celle, Steimbke near Nienburg, Worms in the Rhine Valley, Gifhorn near Braunschweig, Mölme near Oberg, and at other places. The drilling activity for oil is illustrated by the figures in Table 2.

Jan 1, 1939

By Carl Beal

Introduction. DURING the latter part of 1915 and the first half of 1916, the writer held the position of geologist in connection with the conservation work instituted by the U. S. Bureau of Mines, on oil and gas land belonging to the Indians of the Five Civilized Tribes in Oklahoma. The duty of the geologist was to correlate formations containing oil, gas,-and water, and to determine the relations of these substances in the different formations so that the conservation agents might carry on their work most intelligently. On account of the rapid development of the Cushing field, which lies in the western part of the Creek Nation, much work was clone there by the inspection force. In the course of the geologic studies a large amount of information was collected, which, on analysis, has disclosed some interesting facts worthy of publication. The report, of which the following remarks are an abstract, has been prepared and submitted to the U. S. Geological Survey for publication. This report is now (June, 1917) in the press and will doubtless be issued in a few weeks. Methods Used In addition to the structure maps showing the folding of the Pawhuska limestone, which crops out in several places in the Coshing field, separate structure maps of the three most important productive sands-the Layton (Fig. 2), Wheeler, and Bartlesville-have been prepared. These structure maps, were prepared by obtaining the logs of nearly all the wells

Jan 8, 1917