Search Documents

By Noel Cunningham

MANY excellent descriptions of the mills of the, Porcupine district have been written, but no discussion exclusively devoted to the metallurgical technology has been given. These notes are intended to cover this feature briefly. They are based upon 2 ½ years' mill operation in the district-i.e., practically since the beginning of metallurgical operations. Character of the Porcupine Ore.-There is no oxidized ore in the district, the surface having been deeply planed by glacial action in recent geologic time. The precious-metal content is about in the proportion of 85 of gold to 15? of silver by weight; hence, the silver is practically negligible. There are two classes of Porcupine ore, having very different characteristics; these will be referred to throughout this paper as Class A and Class B. Class A ore is a pure quartz with inclusions of schist. Generally it is heavily fractured .and breaks down readily to sharp, hard grains, about minus 10 plus 20 mesh, requiring further comminution to release the gold. It carries very little pyrite; the gold is entirely free and apt to be coarse, but often spongy, going into solution readily on that account. This gold is 60 per cent. to 85 per cent. free milling, depending on the grade of ore. Class B ore is an iron silicate schist, strongly laminated, carrying 4 to 5 per cent. pyrite; its specific gravity is 2.8 to 3.0, depending upon the amount of mineralization. In breaking the ore in the mine, generally over 25 per cent. of material through a ½ -in. ring is made; the ore readily breaks down in milling and makes a comparatively large amount of non-crystalline slime; owing to its high specific gravity, however, it is quick settling.' In my opinion, the gold in this ore is free, but so finely divided that it will neither pan nor amalgamate; it appears to be disseminated through the rock and not chiefly associated with the pyrite. Veins of Class A ore occur with or without side walls of Class B, and veins of Class B occur unassociated with Class A; more often the veins are closely banded, Class A and Class B alternating, generally with Class B in excess. Both classes of ore are more-or less blocky at times, and with ref¬erence to Class B this is indicative or low gold content.

Jan 3, 1915

By Casper A. Nelson, Wendell M. Whitecotton

A WIDE variety of lead ore is treated by the Midvale Smelter, for it is a custom plant not only treating Company lead concentrate and direct-smelting ores but also custom ores and concentrates, principally from Utah, Idaho, and Nevada, with lesser amounts from Arizona, California, Colorado, Montana, Oregon, and Washington. The principal operating departments of the plant are weighing and sampling, Wedge roaster, D&L sintering, blast furnace and drossing, and baghouse. The lead bullion produced is shipped to a subsidiary, the U.S.S. Lead Refinery, Inc., at East Chicago, while the by-products, such as matte and speiss, are shipped to other smelters or re-treated at the plant.

Jan 1, 1948

By W. H. Corbould

The township of Cloncurry is situated in the northwestern part of Queensland, about latitude S. 20" 42' 53" and longitude E. 140" 30' 25". Townsville is the port through which all the trade passes and is about 470 miles east-northeast of Cloncurry township. The Cloncurry copper district covers an area about 200 miles long by 40 miles wide. Unfortunately the mines are very scattered over this area, there being no large groups of mines. Mount Elliott mine is situated about 70 miles south from the township of Cloncurry, and Mount Oxide mine about 150 miles north of Cloncurry. The district has been known for the last 35 years, and in the early stages a large amount of capital was expended with little to show for it; but within the last four years the railway has been extended from Townsville to Mount Elliott and about 40 miles north of Cloncurry, which has made possible the treatment of the ores of the mines on this extension. The Mount Elliott company within the last few years has smelted and converted on its mine 169,688 tons of ore for 20,554 tons of blister copper, containing 20,377 tons of copper, 35,642 oz. of gold and 28,841 oz. of silver, at a cost of about 233 per ton of blister copper, f.o.b. Townsville. This cost included all development, wages, salaries, general management, office, agency, legal expenses, freight, etc. The gold and silver contents would practically pay for freight to Europe, refining, realization charges, etc. The costs of supplies are as follows: Firewood, 15s., coke, 75s., mine timber, 54s., and coal, 60s. per long ton; explosives: dynamite and gelignite, 50s., and blasting gelatine, 65s. 6d. per case, Mount Elliott Mine The pay shoot of the orebody outcrops at the surface for about 200 ft., and lies between two slate walls about 40 ft. apart., having a general

Jan 1, 1915

By C. E. McCarthy, A. George Stern, Stanley J. Green

THE national interest prompts consideration of any new source of mineral wealth even though the immediate need may be of minor importance. A critical shortage of potash in the United States during the World War of I9I4-I8 stimulated broad development, which established an American potash industry on a basis so sound that this commodity is not even listed as urgent in the present war program. However, this should not minimize its importance, and the need remains, not only for adequate supplies of the usual potash salts (the chloride and the sulphate) but of all potash chemicals. Potassium carbonate (known commercially as pearl ash) has been a high-cost commodity; in consequence, the quantity used by industry has been relatively small. By a combination of fortuitous geographical circumstances, there is opportunity to produce a low-cost potassium carbonate with the possibility that this might become an important source of chemical potash. The following paper considers a recently developed process1 taking advantage of these conditions. WYOMINGITE DEPOSIT For many years it has been known that a deposit of potash-bearing igneous rock known as wyomingite occurs in the southwestern part of Wyoming at Zirkel Mesa, which is 44 miles northeast of the town of Green River (Fig. I). The western escarpment of this deposit is about 3 miles east of the Superior Branch of the Union Pacific Railroad. This mesa alone covers approximately 3300 acres, and the average thickness of the wyomingite flow is 75 ft. It has been estimated2 that about one billion tons of wyomingite occur in this one deposit, all of which can be mined by open quarrying without overburden. In addition, there are several smaller deposits within 10 miles, so that the aggregate wyomingite in the area approaches two billion tons. This is one of the world's largest sources of leucite, and the only known deposit of its kind in the United States. The wyomingite (which is in the form of a lava flow and numerous small craters), with the mineral leucite as its most important component, has a mineral composition3 of: leucite, 50 per cent; phlogopite, 15; diopside, I2; kataphorite, 15; glass and apatite, 8. The phlogopite is present in visible phenocrysts 1/8 to 1/2 in. in diameter, but the leucite usually is almost microcrystalline and not capable of liberation by grinding. Chemically, the wyomingite has a potash content averaging slightly higher than eleven per cent K20. The potash is mainly in the leucite, but part of it is in the phlogopite and a small amount is in the feldspars that are occasionally seen as undigested occlusions of the granite country rock, through which the leucite-bearing lava intruded, and as sanidine feldspar both in the crystalline and glassy phases of the rock. A typical analysis of the wyomingite from Zirkel Mesa is as follows:

Jan 1, 1944

By R. R. Seeber

(Pittsburg Meeting, March, 1910.) IN the copper-mining district of northern Michigan a fair-sized mine usually operates two or more shafts along the strike of the lode, these shafts being usually at least 1,000 ft. apart. The tonnage to be hoisted from each shaft is large-from 13,000 to 25,000 tons per month. The hoisting-engines used are generally steam-driven, non-condensing, duplex engines with Corliss valves, supplied by steam from separate boiler-plants where the distance between shafts is great. In an attempt to centralize power-plants and secure central-station economies, the Winona Copper Co. installed an electric hoist of the Ilgner type, with Ward Leonard control. A brief description of this plant has already been published.1 The only point of variation from the simple Ilgner set lies in the connection of two generators to a single induction-motor by flexible couplings. These generators serve motors which operate hoisting-drums at separate shafts, viz., No. 4 shaft, Winona, and No. 1 shaft, King Philip. , The hoist for No. 4 shaft, is about 1,700 ft. from the power-plant, and in this building the motor-generator set is placed. No. 1 King Philip hoist is 1,500 ft. from the motor-generator set. The equipment of the motor-generator set is as follows: In the middle of the set is a 12-pole, 450-h-p., 600-rev. per min., 2,080-volt, three-phase, 60-cycle, variable-speed induction-motor, connected on each side to a 20-ton fly-wheel which is 10 ft. in diameter, and to a 6-pole, 170-kw, 575-volt, interpole, direct-current generator. On each side of the shaft is placed a separate exciter, which delivers current at 125 volts. The lubrication of the four main bearings that support the fly-wheels * Presented also, by mutual agreement, at the meeting of the American Institute of Electrical Engineers, New York, N. Y., Mar. 11, 1910. Engineering and Mining Journal, vol. lxxxviii., No. 3, p. 110 (July 17, 1909).

Sep 1, 1910

By Henry G. Petrow, Edward S. Porter

MAJOR occurrences of lignite with significant uranium concentrations have been reported in western parts of the Dakotas, especially in Harding County, S.D., and Billings and Slope counties, N.D. Samples containing as much as 2 pct U3O8 were received at the Winchester Laboratory, but those deposits reportedly of major significance have generally contained 2 to 4 lb of uranium per ton of lignite. Most of the uranium appears to be associated with the carbon in the lignite as a urano-organic complex, although in most instances analysis of inorganic material has shown uranium values. Molybdenum is similarly associated with the carbon, and its concentrations generally parallel the uranium. The noncarboniferous material is mainly composed of gypsum, jarosite, bentonite, sandstone, and miscellaneous carbonates and silicates. The heating value of these lignites has been determined as about 3500 Btu on a dry lignite basis. The ash content of lignite has varied widely, the important samples containing 30 to 60 pct ash on a dry lignite basis. Because of the significant upgrading of uranium values obtained by ashing the lignite, and because recovery of uranium from raw lignite presented formidable processing problems, major emphasis at Winchester has been placed on devising methods to recover uranium from lignite calcines. Proper roasting removes the problem of organic fouling of solutions, reduces the size of the leaching plant for an equivalent uranium throughout, and generally provides equal or better acid leaching efficiency with less acid than can be obtained from the raw lignite.

Jan 9, 1957

By Rollyn P. Jacobson

THE town of Pacific, in Jefferson County, Mo., is 127 miles west of St. Louis. Since the area lies entirely on the flood plain of a cutoff meander of the Meramac River, it was considered a likely environment for accumulation of commercial quantities of sand and gravel. Excellent transportation facilities are afforded by two major railways to St. Louis, and ample water supply for washing and separation is assured by the proximity of the river. As a large washing and separation plant was planned, the property was evaluated in detail to justify the high initial expenditure. An intensive testing program using both geophysical and drilling methods was designed and carried out. The prospect was surveyed topographically and a 200-ft grid staked on which electrical resistivity depth profiles were observed at 130 points. The Wenner 4-electrode configuration and earth resistivity apparatus" were used. In all but a few cases, the electrode spacing, A, was increased in increments of 11/2 ft to a spread of 30 ft and in increments of 3 ft thereafter. Initial drilling was done with a rig designated as the California Earth Boring Machine, which uses a bucket-shaped bit and produces a hole 3 ft in diam. Because of excessive water conditions and lack of consolidation in the gravel there was considerable loss of hole with this type of equipment. A standard churn drill was employed, therefore, to penetrate to bedrock. Eighteen bucket-drill holes and eight churn-drill holes were drilled at widely scattered locations on the grill. The depth to bedrock and the configuration will not be discussed, as this parameter is not the primary concern. Thickness of overburden overlying the gravel beds or lenses became the important economic criterion of the prospect.** The wide variety and gradational character of the geologic conditions prevailing in this area are illustrated by sample sections on Fig. 2. Depth profiles at stations E-3 and J-7 are very similar in shape and numerical range, but as shown by drilling, they are measures of very different geologic sequences. At 5-7 the gravel is overlain by 15 ft of overburden, but at E-3 bedrock is overlain by about 5 ft of soil and mantle. Stations L-8 and H-18 are representative of areas where gravel lies within 10 ft of surface. In most profiles of this type it was very difficult to locate the resistivity breaks denoting the overburden-gravel interface. In a number of cases, as shown by stations M-4 and H-18, the anomaly produced by the water table or the moisture line often obscured the anomaly due to gravel or was mistaken for it. In any case, the precise determination of depth to gravel was prevented by the gradual transition from sand to sandy gravel to gravel. In spite of these difficulties, errors involved in the interpretation were not greatly out of order. However, results indicated that the prospect was very nearly marginal from an economic point of view, and to justify expenditures for plant facilities a more precise evaluation was undertaken. The most favorable sections of the property were tested with hand augers. The original grid was followed. In all, 46 hand auger holes were drilled to gravel or refusal and the results made available to the writer for further analysis and interpretation. When data for this survey was studied, it immediately became apparent that a very definite correlation existed between the numerical value of the apparent resistivity at some constant depth and the thickness of the overburden. Such a correlation is seldom regarded in interpretation in more than a very qualitative way, except in the various theoretical methods developed by Hummel, Tagg (Ref. 1, pp. 136-139), Roman (Ref. 2, pp. 6-12), Rosenzweig (Ref. 3, pp. 408-417), and Wilcox (Ref. 4, pp. 36-46). Various statistical procedures were used to place this relationship on a quantitative basis. The large amount of drilling information available made such an approach feasible. The thickness of overburden was plotted against the apparent resistivity at a constant depth less than the depth of bedrock for the 65 stations where drilling information was available. A curve of best fit was drawn through these points and the equation of the curve determined. For this relationship the curve was found to be of the form p = b D where p is the apparent resistivity, D the thickness of overburden, and b a constant. The equation is of the power type and plots as a straight line on log-log paper. The statistical validity of this equation was analyzed by computation of a parameter called Pearson's correlation coefficient for several different depths of measurements, see Ref. 5, pp. 196-241. In all but those measurements taken at relatively shallow depths, the correlation as given by this general equation was found to have a high order of validity on the basis of statistical theory.

Jan 1, 1956

By W. W. Stephen, J. P. Walsted, W. J. Kroll

FOR the production of carbides, various furnace types are available, especially those using arc, resistance, and high-frequency heating. Selection of a specific means of heating depends primarily on the material to be treated and the physical properties of the carbide produced. In the present case, zirconium carbide had to be prepared on an industrial scale as a raw material for the production of anhydrous zirconium chloride. Considering that a rather expensive pure oxide was to be used, the arc-furnace treatment recommended for zircon sands in a previous publication' was ruled out because of the considerable volatilization and dust losses caused by the blast of the arc. For this reason, either high-frequency or resistance heating seemed to offer more promise. Since there was not enough capacity of the former available, resistance heating was chosen. It was first thought that the Acheson silicon carbide furnace would be suitable for the present purpose, but the voltage in such a furnace, in which the current passes through the batch, varies from 220 to 75 v from the start to the end of a run. This variation is so great that a special tap transformer would have been required. Trouble was also expected by local melting of the carbide. Pure zirconium carbide melts at about 3527°C, but the melting point is brought down to 2427°C, according to Agte,2 when an excess of 6 pct C is present in the carbide. This we found confirmed by experiments in a high-frequency furnace. Excess carbon is needed in the batch to obtain a complete reduction. Fusion of the charge would cause great difficulties in an Acheson-type furnace because of the good electrical conductivity of the carbide as compared with that of the loose batch. Also, fused carbide is much more difficult to chlorinate than the spongy product that can be made in the radiation furnace described below. It was apparent that, to obtain a good-qual-ity zirconium carbide, the heat input would have to be well-controlled. The hairpin-resistor principle seemed to offer possibilities in this regard, and a furnace of this type was therefore developed. The advantages of the hairpin-resistor radiation principle have been discussed in previous publications, and a split-tube graphite-resistor furnace," now increasingly used in various laboratories, as well as a centrifugal quartz melting furnace4 of this type, has demonstrated the usefulness of this heating method. The hairpin-heater element has the following definite advantages over a straight resistor of the type used, for instance, by Georges:5 Its resistance is four times greater; it can expand freely; it is sturdier because of the larger diameter, and it has a larger radiation surface; there are no hot contacts that might wear out or overheat; only one clamp is used which permits assembling all electrical leads at one side of the furnace, making the other sides easily accessible to the operator. The shorter element and its larger diameter permit greater concentration of heat. The furnace developed is shown in fig. 1. The box (I), made of 2 1/2-in. graphite plates, has inside dimensions of 23x17x16 in. It contains the briquet-ted batch (2). The box is embedded in lampblack (3) up to the cover plate. The cover plate contains an opening for the gas escape (4) and for the observation hole (5), which permits measuring the temperature with an optical pyrometer. The cover plate is embedded in charcoal (6). The lampblack is contained in the insulating brick lining (7), held in the 1/4-in. sheet steel box (8). The graphite box is set on two rows of triangular graphite bars (9). The hairpin-heater element (10), the dimensions of which are given below the main drawing, extends horizontally in the graphite chamber and radiates freely on the batch. A graphite tube (11) keeps the lampblack from falling into the slot. The split electrode, which in reality is turned 90" against the drawing, is so arranged that the slot is vertical. The water-cooled packing gland (12) is insulated by an airgap from the heater element. A thin pipe (13)

Jan 1, 1951

By Oliver Bowles

A NORTH CAROLINA miner dreamed that he found high-grade mica by excavating a certain corner of his mine. The next day he sank a hole on the exact spot and found mica of excellent quality. The dream came true. May not this be as good a method as any yet known for forecasting the valuable mineral content of pegmatites? The Federal Geological Survey has found in its recent detailed studies in New England that good sheet mica occurs most abundantly in zoned pegmatites, particularly in zones lying along the wall or contact of the pegmatite mass. Although this conclusion may be a valuable guide, pegmatite mining operations must still be classed as most uncertain and hazardous enterprises. Finding of the second largest diamond ever discovered in the United States-a stone of good gem quality weighing more than 34 carats-during the course of a horseshoe pitching contest at Peterstown, W. Va., is another example of unorthodox mining methods. These should not be considered, however, as characteristic mining methods developed in 1944.

Jan 1, 1945

By E. W. Davis

THIS nation has been depending upon the Lake Superior iron ranges for most of its iron ore requirements for over half a century. Furthermore, it can continue to draw the major portion of its ore requirements from the same source for another century or more, but to accomplish this, great changes must take place in the present ore mining industry. Preliminary preparations for these changes are now underway and in the next few years decisions of far-reaching importance must be made. But to understand the situation, it is first necessary to know something of the nature and occurrence of the Lake Superior iron formation. So far as is known, the merchantable grades of iron ore remaining in the various Lake Superior ranges are as shown in Table 1, which shows that

Jan 1, 1947

By L. D. Wooddy, Robert Moscrip

The simultaneous solution of the volumerric balance and the unsteady-state equation has been used for several years to make performance calculations for combination drive reservoirs. This method makes possible the calculation of volumetric changes of fluids in the gas cap, oil zone, and aquifer which occur as a result of withdrawals and reservoir pressure changes. It does not provide a means for the determination of reservoir fluid distribution changes corresponding to these vollrmetric changes. A knowledge of the fluid saturation distribution in the reservoir at various stages of depletion is important for the determination of the efficiency of gas and water as oil-displacement media and, therefore, for the reliable predicrion of ultimate oil recovery. To provide this knowledge, the displacement equations are solved simultaneously with the volumetric balance and unsteady-state equations. The described calculation procedure has been used satisfactorily to analyze the past performance and to predict the future behavior of combination drive reservoirs under both primary and pressure-maintenance operations. INTRODUCTION The three basic mechanisms by which oil is displaced from a reservoir are: (1) dissolved gas drive—the displacement of oil by the expansion of liberated solution gas, (2) water drive—the displacement of oil by water which enters the oil zone from the aquifer, and (3) gas cap drive—the displacement of oil by gas which ex- pands into the oil zone from the gas cap. The action of gravitational forces may be effective in increasing the efficiency of the basic drive mechanisms. Gravitational forces favor the segregation both of gas and oil and of oil and water, thus tending to shorten the transition zone between oil and displacing fluids. Most reservoirs produce under the influence of a combination of these drives and are designated "combination drive reservoirs". Fig. 1 is a cross section of a typical combination drive reservoir. A calculation procedure for analyzing the performance of combination drive reservoirs has been developed by combining the displacement equations' with the volumetric balance equation' and the unsteady-state equations. The pressure-production performance and the positions of the gas-oil and oil-water contacts are calculated for several stages of reservoir depletion by solving these equations simultaneously, thus affording a basis for: 1. Determining instantaneous and ultimate oil, gas, and water production under various operating conditions. 2. 'Establishing a maximum efficient rate of production, 3. Determining the advantages of pressure maintenance and unitization, and 4. Designing surface installations necessary for primarv and pressure-maintenance operations. DEFINITIONS The calculation procedure for combination drive res-

Jan 1, 1957

By Walter R. Hibbard

ALTHOUGH extensive pole figure studies have been reported by Brick1 and others2,3 showing preferred orientations in rolled and annealed 70-30 alpha brass, and by Hermann and Sachs4 in 70-30 alpha brass cups, comparatively little information has been published on textures in drawn 70-30 alpha brass tubes. Crampton5 reported a (110), [III] texture in drawn brass tubes based on selected individual X ray photograms following the method of Norton and Hiller,6 but the extent and ease of developing this texture and the annealing texture have not been reported and pole figures of these structures were not found in the literature. The present investigation was further stimulated by the possible influence of textures on the mercury stress-corrosion cracking of brass tubes. According to Snoek,7 iron-nickel alloy sheet with a strong cubic texture was more resistant to corrosion than a randomly oriented sheet. Crampon5 reported that single crystals of 70-30 alpha brass drawn into tubes did not crack after 24 hr s in a standard mercurous nitrate test. Edmunds 12 found that single crystals of 70-30 alpha brass did not crack in a standard mercurous nitrate test but did crack when subjected to ammoniacal vapor. Wassermann reported a similar failure of a single crystal of brass in ammonia. A tube with a strong texture might approach single crystal behavior and tend to resist mercury cracking if the differences in orientation between adjacent grains were sufficiently slight. PREPARATION OF SPECIMENS Crampton's5 tubes drawn 28 pct reduction in area developed a slight degree of preferred orientation while in tubes drawn 48 pct it was more marked. Based on this information, in order to obtain specimens with markedly different degrees of preferred orientation but with the same final draw, two sets of 70-30 alpha brass tubes were made following the mill schedules shown in Table I. The final draw involved a large reduction in outside diameter, and a ratio of reduction in area to reduction in outside diameter similar to that reported by Crampton,5,10 to cause mercury cracking of brass tubes. The brass contained 71.31 pct copper, 0.01 pct lead, 0.01 pct iron and zinc by difference. DETERMINATION OF POLE FIGURES A 6-in. length from each tube was rotated rapidly by an electric stirrer in 25 pct nitric acid until the gauge was reduced to 0.003-0.005 in. The tubes were carefully cut longitudinally and the walls gently flattened. They were further etched in 25 pct nitric acid to 0.0015 in. thickness and (III) pole figures were determined using copper K-alpha radiation in the manner described by Brick.1 The three general types of pole figures

Jan 1, 1947

By P. E. Hopkins

Introduction and History IN speaking of the economic geology of southeastern Ontario, W. G. Miller and C. W. Knight' say that "there occurs in southeastern Ontario a variety of minerals and rocks of economic value, probably as great as in any district of like size on the North American continent. Some of these deposits, including marble and trap, are inexhaustible. Others, including talc and iron pyrites, have proved to be of considerable economic importance. From time to time, during the last 50 years, the following minerals and rocks have been mined or quarried with varying success: gold, iron pyrites, zinc blende, copper pyrites, galena, mispickel, magnetite, hematite, talc, actinolite, mica, marble, ophicalcite, feldspar; fluorite, apatite, corundum, graphite and sodalite. All of the economic materials, with the exception of fluorite, appear to be of pre-Cambrian age. The fluorite veins penetrate the Ordovician, Black River, limestone." Accompanying that report was an article by the writer on the Queensboro Pyrite Area which includes one of the two working pyrite properties in southeastern Ontario. In the present paper will be given a brief description' of all the known pyrite deposits in the area which may at some time possess an economic value, with fuller descriptions of the two working mines-The Canadian Sulphur Ore Co.'s mine near Queensboro, and the Nichols Chemical Co.'s property at Sulphide. The earliest mining of iron pyrites in Ontario was done in 1868 on the Billings property near Brockville. The mines were closed down in 1879 under the assumption that they were exhausted. Many other

Jan 8, 1916

By D. W. Brunton

Discussion of the paper of D. W. Brunton, presented at the Spokane meeting, September, 1909, and published in Bulletin No. 33, September, 1909, pp. 837 to 855. WILLIAM' KENT, New York, N. Y.:-The Institute may congratulate itself on the opportunity of reading the splendid address of President Brunton. It is au admirable summary of the progress that has been made in the mining and metallurgical arts in recent years. The paper rightly give's the chief credit for this progress to the aid which has been rendered to these arts by the advances in mechanics, chemistry, and electricity. It is notable that most of the headings in Mr. Brunton's address refer to the work of the mechanical engineer, the electrical engineer, and the chemist, rather than to that of the specialist in mining-operations. It seems that. the most successful mining engineer of the present day is the one who makes the most intelligent application of the inventions and designs of engineers and others who are not directly engaged in mining. A tabulation' of the headings of the address, grouped as below, shows this most clearly. Work of the Mechanical Engineer-Rock-drills, hoisting-machinery, tramming, pumping, ventilation, dredging, sampling, concentration, briquetting, fume-recovery. Work of the Electrical Engineer-Electric machinery for hoisting, pumping, tramming, lighting and signaling, electric . transmission, electric smelting. Work of the Chemist and Metallurgist-Explosives, chlorination, cyanidation, roasting, lead-smelting, and copper-smelting. Work of the Geologist-Economic geology. Work of the Mining Engineer-Mine-mapping, surface-mining, timbering, tunneling; and planning and supervision of the work in general. The mining engineer of the present day, who is in responsible charge of a large plant, finds his chief work not in doing

Jan 1, 1910

By L. C. McCabe

THE object of the present investigation was to discover a physical basis for rank differentiation of coals, particularly the coals of the Illinois basin. Vitrain1 was selected as the most appropriate coal material to use in the investigation, because of its homogeneity and ease of acquisition and handling. Previous Investigations.-Hoffman and Jenker2 have shown that their index of reflection is a characteristic of coal rank and that the Leitz slit microphotometer may he used in determining the different intensities of reflection. Zhemchuzhnikov3 measured the luster of several Russian coals with a color analyzer and found that the degree of luster was indic-ative of rank. Luster-volatile matter curves based on data from Sucan and Donetz coals were satisfactorily used for determining the rank or volatile content of other coals after the luster strength was determined. In 1934 Fisher4 reported refractive indices of 1.76 for bituminous vitrain and 1.87 for semibituminous vitrain. Investigation of Angle of Polarization.-Early in the present investiga-tion several determinations of the refractive indices of the vitrains were made by immersing the minus 150 plus 200-mesh powder in oils. It was found that all the samples fell within the range 1.6 to 1.8. However, difficulty was encountered in securing oils in this high index range that were closely enough spaced to separate some of the coals. The writers made a number of determinations of the angle of maxi-mum polarization from the polished surfaces of the vitrains and derived their refractive indices by the procedure described in the follow-ing paragraphs.

Jan 1, 1937

By David T. Day

In the summer of 1898, a demand suddenly arose for commercial quantities of the element osmium. At least half a ton was wanted for the manufacture of a new incandescent light. This led the writer to examine localities where platinum had been reported, in order to determine whether osmiridium mas contained in the crude platinum. With the co-operation of the concern most interested, the Welsbach Light Company, and in company with its President, Col. William E. Barrows, I visited most of the leading American localities where platinum has been obtained. I also wrote to every available placer-mine in the West for samples of the heaviest sands, in order to test them for platinum. The results of this inquiry are given in the present paper. Distribution. The notices of the occurrence of platinum in this country given in scientific journals include two interesting observa tions in the East. One concerns a nugget described by Peter Collier of Washington, D. C.,* and said to have been found on land adjacent to the village of Plattsburgh, N. Y., which weighed 104.4 grammes, and contained sufficient chromite to reduce the specific gravity from 17.35 for the heaviest portion to

Jan 1, 1901

By L. M. Cathles, W. Joseph Schlitt

A mathematical model describing the leaching of low grade industrial waste dumps in developed and solved by finite difference techniques. The leaching behavior of model dumps of different sizes, permeabilities, and waste characteristics, under different operating conditions, is then investigated using the model. It is shown that leaching is fastest for dumps 50-100 feet (15-30m) high, that permeability is very important for the effective leaching of large dumps, that slow leach kinetics of the waste may not be detrimental, and that the leaching of large dumps may be facilitated if leach solutions are preferentially applied to the hot, near-edge portions of the dump.

Jan 1, 1980

By R. F. Mehl, B. Lustman

THE formation of intermediate phase layers in cementation processes has been subjected to extensive qualitative investigation though to relatively little quantitative study; this work has recently been fully summarized by F. N. Rhines.1 It is necessary here only to enumerate the general conclusions drawn concerning the kinetic laws governing the growth of intermediate layers and to state what is known concerning the structural changes accompanying the generation of phase layers. I. When the intermediate phase is protective in type-i.e., when its density is less than that of the base metal, so that a continuous coating is formed and maintained-the isothermal growth of the phase follows a simple parabolic equation: [1 = ki [I]] where X is the thickness of the alloy layer, k the reaction rate constant, and [t] the time. The applicability of this equation to diffusion processes is tested by plotting the square of the thickness versus time, or by plotting the thickness versus the square root of time; the resultant achievement of a straight line in such a plot has been considered sufficient proof of the validity of this equation. Exceptions have been found where liquid phases are involved in the reaction, where the diffusion layer is cracked,2 and where thin semimetallic oxide and sulphide coatings are formed on metals.3 In the first two cases the thickness increases linearly with time, and in the latter it is a logarithmic function of time. 2. The rate of thickening varies with temperature according to the Arrhenius equation: [k = Ae-QIRT [2]] where k is the parabolic rate constant of Eq. I, or some other rate-descriptive function, A is the action constant, e the base of natural logarithms, Q the heat of activation, R the gas constant, and T absolute temperature. This equation has been found to be generally valid except when transformations occur during reaction in either the base metal or in the reaction layer; in such instances Eq. 2 is still applicable with different values for the constants A and Q above and below the transformation temperature. 3. All phases that are stable at the temperature at which diffusion occurs will appear in the interdiffusion of two components. In some cases certain of the phases may be too thin to be observed and identified easily. Nonequilibrium phases have never been noted in thick reaction layers; i.e., layers of a thickness that may be discerned microscopically. The relative thickness of each phase in a diffusion layer is proportional to the concentration gradient and to the rate of diffusion in that phase.4 The reaction layers tend to have a

Jan 1, 1942

By Rztssell H. Bennett

A SURVEY of the Mesabi Range iron-ore industry demonstrates that a satisfactory degree of technical progress has been achieved in the last fifteen years. This advance has not been made over a uniform front, but, by salients and bays, according to the different initial positions, economic and technical, of the component producing companies. The producers endowed with rich ore have in general, because of natural advantages, progressed more slowly than their neighbors with leaner properties. The advance has been made step by step all along the line -blasting, loading, hauling and concentrating-and without the benefit of radical innovation. There have been, for instance, no such parallel discoveries in iron ore as leaching and flotation in copper. The much lower unit price of iron operates, of course, to bar the application of these and other practices developed for the higher-priced metals. There exists, however, a radically new concentration process whose technology is well worked out and which may become economically operative in the not too distant future; this, as so often happens in engineering advance, because of recent developments in an entirely unrelated field. First, however, let me devote a paragraph or two to the more important economies effected in mining.

Jan 1, 1932

By B. C. Allen

The interface energies of chronzium, molybdenunz. hugsten, and their solid-solution alloys Cv-35Re, MO-33Re, and UJ-25Re were studied at 0.6 to 1.0 of the absolllte liquidus ter)zpe,vature using fiz&apos;e )izethods. Liquid surface tension, yv , was deter mined clsing the pendant-drop and drop-weight methods. Results are, respectizlely, 1700, 2370, and 2480 +100 dynes per ct for the rhernium -containing alloys and essentially the same as tlwse reported for liquid chro)riln, trolybdenum, and tungsten. Average solid slrjace energy, rsv< xias ))zeasured using tlre fiber-extetlsion method. The ratio of ysS, the acerage high-angle grain-boundary energy, to ySV cclas jolnd fronz grain-bolzdary grooue angles fort)zed at the surface in an inert atrfizosphere. Absolllte iute?:face energies were deterawined using ?nultip/rase equilibria involzing suitable liquids of known surface tension (tin, silver). Interpretation of the experimented results in view of pvobable tenzperatzcre, orientation, and purity effects giz,e the follouling approximations in ergs per sq ctn: ysv (i2lo. Mo-33Re) - 2100, ySS (Mo, Mo-33Re) - 800, rr (defornzation twins in MO-33Re at 1200"C) - 800. ysV (Cr. Cr-35Re) - 2400. YSS (CY, Cr-35Re) - 1000. Probably Ylv- YSV- 2500 for tungsten and W-25Re, giving yss (It&apos;, W-25Re) - 900. The interface energies of solid and liqid ch?&apos;omiu?.z, nolybdenu?rr, and tungsten are not geatly aff&apos;ected by rhenium and therefore are not a ttlajor factor in the ductili zing rhenium effect in Croup VI-A metals. THE interface energies of the refractory Group VI-A metals, chromium, molybdenum, and tungsten, are not well-established. The objective of this investigation was to study the liquid surface tension, solid surface energy, and grain-boundary energy of these metals and compare them to those found for the bcc solid-solution alloys, Cr-35e,&apos; 0-33e,&apos; and -25e. Five techniques were used to measure interface energies in high-purity polycrystal rod, wire, and sheet at 0.6 to 1.0 of the absolute liquidus temperature. The alloys were chosen to see if there was any connection between interface-energy behavior and the ductilizing rhenium effecL4j5 EXPERIMENTAL WORK Materials. A description of the materials used is presented in Table I. Chromium rod was prepared by arc melting iodide process crystals supplied by Chromallo Cor., hot extruding, and warm swaging to 0.63-cm-diam rod.6 The sheet was prepared by rolling as-extruded rod to 95 pct reduction in area from a hydrogen furnace at 800" to 900°C and surface grinding off 0.02 cm from each face. Cr-35Re rod was prepared by arc melting sintered rhenium powder and iodide chromium crystals, warm rod rolling to 50 pct reduction in area in cans, and swaging to 60 pct reduction in area at 1100" to 1200°C. Some of the rod was warm-rolled to sheet and then surface-ground. Portions of swaged chromium and Cr-35Re were further reduced by swaging and drawing to 0.013-cm-diam wire by the General Electric Co. Mo-33Re and W-25Re rod, sheet, and wire were provided by Chase Brass and Copper Co. The molybdenum sheet consisted of two lots, both essentially the same except for the carbon content. Liquid Surface Tension. The liquid surface tension of Cr-35Re, Mo-33Re, and W-25Re was measured by a combination of pendant-drop and drop-weight methods using techniques already decribed." Following out-gassing, molten drops were formed on the ends of centerless-ground Mo-33Re and W-25Re rods by electron bombardment at 5 x 106 mm. Similar drops were formed on outgassed Cr-35Re rods by induction heating under 1 atm of 99.995 pct Ar. Solid Surface Energy. Solid surface energy was measured by conducting microcreep experiments on molybdenum, Mo-33Re, chromium, and Cr-35Re wires at 2350°, 2306, 1550°, and 180O°C, respectively. In preparation, gage marks -2.5 cm apart and -0.001 cm deep were circumferentially scribed on the wire with a razor blade. Weights of the wire material were then attached. Five to seven reasonably straight wires were hung in a container made out of the wire material. The free end was placed through a small hole in the removable top and secured by bending a small portion 90 deg. The containers not only tended to provide vapor-solid equilibrium for the wires but also protected them from gaseous impurities. They were nominally 2.5 cm in diam by 5 cm high and were made from extruded chromium rod, Cr-35Re arc casting, molybdenum bar stock, or welded Mo-33Re sheet. After deg re as ing, the assembly was outgassed at a relatively low temperature to 2 x 10"5 mm and then recrystallized 2 to 8 hr at the creep temperature in a rhenium-element resistance furnace. The static argon atmosphere was gettered by tantalum radiation shielding. Specimen temperature was measured optically to 25"C using calibration with known melting points and blackbody conditions. The wires generally developed a stable bamboo-type structure according to Fig, l(b), (c), and (d) and retained their gage marks [upper portion of Fig. l(d)]. One or two of the weights were clipped off to provide a low load for the creep anneal. To minimize the possibility of bending or breakage, the wires remained attached to the top of the annealing container which was held to keep the wires vertical. The distance between gage marks was

Jan 1, 1967