Search Documents

The following figures (Nos. 1-4) and tables (Nos. 1 and 2) were inadvertently omitted from the chapter entitled "Optimum Open-Pit Mine Production Scheduling" by Thys B. Johnson, Section 4, pages 539-562. [ ]

Jan 1, 1969

By Elmars Ence, Harold Margolin

A. J. Goldak and J. Gordon Parr (University of Alberta) —While we appreciate the difficulties involved in any investigation of this system, and we wish to congratulate the authors on their comprehensive efforts, there are several aspects of their paper that are not clear to us. 1) If the 6 phase is, in fact, isomorphous with Ti3Sn, it should not be designated Ti,Al. An 4B structure cannot be isomorphous with an ordered structure of the DO type. Anderko et al.' suggested that the structure be called Ti3A1, and we believe this to be a more reasonable designation. The confusion is compounded when the authors designate the phase Ti3Al—yet the composition limits of this phase (according to their diagram) are approximately Ti,A1 and Ti,Al. Further, while Pietro-kowsky is said to have pointed out that the structure of the 6 phase is isomorphous with Ti3Sn, we understand that this was only a suggestion that was not confirmed. Margolin and Ence do not appear to have presented any evidence to support the suggested isomorphism. 2) In referring to the precipitation observed microscopically during the initial breakdown of high A1 a during quenching, the authors state that "such precipitation is not likely to be detected by Debye-Scherrer techniques". We suspect that if the precipitate was visible by optical microscopy, it must have at least one dimension of the order of 1 or greater, and would therefore be readily detected by diffraction techniques. 3) The authors state: "The basis for this suggestion (that 6 forms peritectically P + L—6) is the observation that the ,'3 + 6 and 6 phase fields were

Jan 1, 1962

By Cyril Smith

THE following table, which is composed of data given in the author's first paper on the thermal conductivity of copper alloys1, contains the results which have been obtained by previous workers on the thermal conductivity of the copper-tin, the copper-phosphorus and the copper-tin-phosphorus alloys (the phosphor bronzes). TABLE 1.-Previous Investigations Composition, Per Cent. by Weight Thermal Conduc¬ Investigator tivity, Cal/Sq. Cm./ Copper Tin Phosphorus CM./Sec.. °C. Hardebecka 95.0 5.0 0.176 (20° C.) Grossmanb 90.1 9.9 0.105 75.5. 24.5 0.059 24.9 75.1 0'.139 (13° C.) 9.7 90.3 0.131 0.0 100.0 0.142 Griffiths and Schofieldc 91.7' 8.0 0.30 0.108 87.2 12.4 0.40 0.087 (20° C.) 90.0 10.0 Small amt. 0.100 Donaldsondd: 87.8 1 11.3 0.35 0.128 Pfleiderere 99.4 1 0.63 0.250 (30° C.) 98.0 1.98. 0.125

Jan 1, 1930

By Norman C. Britz, Mortimer P. Buck

THIS PAPER DEALS WITH the practices used at the Huntington, Nest Virginia works of The International Nickel Company, Inc., in hot and cold rolling nickel and high-nickel alloys. The practical metallurgical aspects are discussed and a brief description of equipment given. The alloys covered may he divided into three main groups. based on their major constituents: 1. Nickel alloys, 2. Nickel-copper alloys. 3. Nickel-chromium alloys. The nominal compositions of the various alloys which are produced in most common mill forms are given in Table 1. Nickel, a commercially pure grade of nickel containing about 0.05 pct carbon as' the chief alloying element, is produced in all common Mill forms. "L" Nickel is commercially pure nickel in which the carbon content is held as low as possible, usually less than 0.01 pct. This grade of nickel is used chiefly for spinning and for special high temperature applications where its low carbon content enhances its corrosion resistance. "D" Nickel contains 4.5 pct manganese to provide improved resistance to sulphur embrittlement at elevated temperatures. "Z" Nickel is an age hardening grade of nickel containing carbon, aluminum, and silicon as the age hardening elements. This alloy combines the cor-

Jan 1, 1948

By H. Biloni

A metallographic study of solute segregation produced during controlled solidification of Sn-Pb alloys has previously been reported.' It was found that the growth conditions which produced well-developed cellular substructures led to severe segregation, and even at solute concentrations of 0.2 wt pct Pb regions of a lead-rich phase were formed at the junctions of cell boundaries (nodes). Similar sample preparation and etching techniques have now been applied to several tin alloys at more dilute concentrations. The crystals were solidified uni-directionally under less-severe growth conditions so that the predominant interface structure was composed of two-dimensional cells.* Binary alloys with lead, using 9.999 pct Sn as a solvent, and ternary alloys with lead and bismuth or lead and antimony, using zone-refined tin as a solvent, were examined. The liquid was decanted from the growing crystals in all cases to reveal the interface structure and ensure that two-dimensional cells were being formed. However, since interference may arise from a liquid layer that clings to the interface during decanting,3 an examination of the segregation pattern was always made behind the interface. In all cases, the structure within the bulk of a crystal at greater than 1 cm behind the decanted interface was substantially the same as that nearer the interface. Representative photomicrographs of the dilute Sn-Pb alloy are shown in Figs. 1, 2, and 3. Most observations are similar to those of the previous investigation. For example, the solute concentration at the cell walls is higher than in the intercellular regions; where cell boundaries meet, the segregation is enhanced; the macromosaic or stria-tion substructure and grain boundaries show enhanced segregation; there is also a depletion of solute at cell walls near a striation boundary, as Spittle et a1.4 have observed at decanted interfaces. Not all these observations can be seen in the photos shown since attention has been focused on a special feature; as evident in the photomicrographs, cer-

Jan 1, 1965

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

By R. B. Gilmore, Lewis W. MacNauhgton

The North Texas district, as' herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, usually are modified by stratigraphic changes in the sediments. Excepting those in southeastern Baylor, southern Archer, and southwestern Clay counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsyl-vanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1942 Approximately 500 wells were drilled in the district during 1942, in contrast with some 1600 wells drilled during 1941, and only some goo oil wells were completed, a decrease from 1941 of more than 10 per cent in the number of successful drilling operations of the total wells drilled. Production increased slightly over the previous year in spite of a decrease in the number of producing wells. The average depth of discovery wells was some 600 ft. deeper than in 1941. Although more discoveries produced from horizons above the base of the Strawn series than those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the addition to oil reserves. The largest single addition to the reserves was again in the Ellenburger formation in the K. M. A. field. During the year 47 wells were completed, bringing the total developed acreage in this horizon to some 5450 acres. The most active area was Montague County, in which eight fields, or potential fields, were discovered although only 39 oil wells were completed. K. M. A: Pressure Maintenance Satisfactory progress was made by the K. M. A. Pressure Maintenance Association in 1942, At the end of the year, 100 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 430,971 M cu. ft. in December, with an input ratio of 587 cu. ft. of gas returned for each barrel of oil produced during the month. This represents a utilization of 50 per cent of the gas available for return during that month. Comparison of the present average bottom-hole pressure by means of a decline

Jan 1, 1943

By R. B. Gilmore, Lewis W. MacNauhgton

The North Texas district, as' herein defined, includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Knox, Montague, Wichita, and Wilbarger. This area covers generally the crest and south flank of a system of buried mountains known as the Red River uplift. The oil and gas accumulations along this feature are in traps, which, although localized by structures incident to the regional uplift, usually are modified by stratigraphic changes in the sediments. Excepting those in southeastern Baylor, southern Archer, and southwestern Clay counties, all the fields within the district are on this Red River uplift. These exceptions, which have the same type of oil and gas accumulation as the other fields, are on the extreme north end of the Bend arch, which is a broad anticline plunging northward from the Llano uplift in central Texas to Archer County. The larger part of past oil and gas production has come from Pennsyl-vanian strata, with less important amounts from the Permian, and minor but increasingly important quantities from the Ordovician. Developments during 1942 Approximately 500 wells were drilled in the district during 1942, in contrast with some 1600 wells drilled during 1941, and only some goo oil wells were completed, a decrease from 1941 of more than 10 per cent in the number of successful drilling operations of the total wells drilled. Production increased slightly over the previous year in spite of a decrease in the number of producing wells. The average depth of discovery wells was some 600 ft. deeper than in 1941. Although more discoveries produced from horizons above the base of the Strawn series than those below the Strawn, the deeper horizons, including the Bend series of the Pennsylvanian, the Mississippian limestone, and the Simpson and Ellenburger of the Ordovician, furnished most of the addition to oil reserves. The largest single addition to the reserves was again in the Ellenburger formation in the K. M. A. field. During the year 47 wells were completed, bringing the total developed acreage in this horizon to some 5450 acres. The most active area was Montague County, in which eight fields, or potential fields, were discovered although only 39 oil wells were completed. K. M. A: Pressure Maintenance Satisfactory progress was made by the K. M. A. Pressure Maintenance Association in 1942, At the end of the year, 100 wells were being used for input and total monthly volume of gas returned to the reservoir reached a high of 430,971 M cu. ft. in December, with an input ratio of 587 cu. ft. of gas returned for each barrel of oil produced during the month. This represents a utilization of 50 per cent of the gas available for return during that month. Comparison of the present average bottom-hole pressure by means of a decline

Jan 1, 1943

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By C. E. Shoenfelt

There were 110 important discoveries of either oil or gas in Co1orado in 1935. There was, however, further development of the Price structure in southern Colorado and developments since the first of the year indicate. that an important oil field may be in the making. The discovery of oil in Price structure was made by the Oil City Petroleum Co. late ill Novem-ber, 1934, in its No. 2 Garnett in the northeast corner of lot 3 in the SW.¼ of sec. 25-33N.-2E. This well developed a good showing of oil in Dakota sand at 970 ft. The hole filled up 15 ft. with 40° gravity oil overnight and after standing for several days the oil level was 400 ft. higher. As a result of the discovery of oil by the No. 2 Garnett, three wells were drilled by the William E. Hughes Estate. Two of these wells had good showings of oil and may make good producers but it is doubtful whether they will produce the estimated capacity of 500 bbl. each with which they have been credited. Although the Hughes Estate wells have been completed for some time, they have not been given thorough production tests because of the isolated position of the field and lack of proper facilities. The. first well drilled by the Hughes Estate was located on the west side of the Navajo River on the downthrow side of a fault. It encoun-tered water ill the Dakota sand at 1285 ft, and was abandoned in green shales of the Morrison at 1405 ft. Well cuttings from the Dakota sand showed some evidence of once containing oil, so a 1ocation was selected for No. 2 Fee on the east side of the river and on the upthrow side of the fault. Oil was discovered in Dakota sands ill 1935 by Continental Oil Co. in its No. 3 Hoye, NW.NW.NE. of sec. 34-9N.-78W., on the South McCallum anticline in North Park, Jackson County, Colo., but on account of heavy flows of carbon dioxide gas under high pressure it has been impossible for the company to get an accurate gage of the oil production. The freezing action of expanding carbon dioxide makes the producing of the oil difficult and costly.

Jan 1, 1936

By John W. Brauns, David H. Orr

9.1-1. Description and Basic Function. A conventional railroad haulage system for a surface mine performs the function of transporting the ore and/or waste out of the pit to a crushing plant or dump. Trains consisting of a locomotive and gondola or side-dump care suitable for loading by power shovels are used. Gondola cars are restricted to hauling ore as a rotary dumper is required to unload them. Side-dump cars are more versa- tile, being satisfactory for carrying both ore and waste; but because of their additional dumping mechanism they are likely to be more expensive to maintain (12). Also they weigh up to two times as much as a flat-bottom car of the same capacity, and, therefore, fewer cars can be hauled per train. Standard-gauge track is most commonly used. Track systems incorporate temporary track of low quality in areas where moves are frequent and permanent track of high quality on main lines. Rail haulage enabled open pit mining to establish its reputation, for efficiency. Prior to World War II it was the principal type of transportation used in large pits. Other successful surface mine haulage methods have been developed since that time. These have served to supplement railroad transportation, permitting selection of a method that is best adapted to the peculiar requirements of each mining project. 9.1-2. General Applicability and Controlling Physical Conditions. For handling rough rock, the shovel-train system is unexcelled (6). The ideal application is in a physically large, but not excessively deep, open pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transported than will any other haulage method. Relatively gentle

Jan 1, 1968

By H. W. Camp

ALTHOUGH the situation in the oil industry during the past year has. not been conducive to large expenditures for development and research, there is little indication that such expenditures have been curtailed. While few outstanding achievements have been reported, considerable progress has been made in the development of new products and the adaptation of petroleum derivatives to new uses. The most important question facing the refiner today is the anti-knock quality of his gasoline. This year has seen the widespread adoption of the term "octane number" as a measure for anti-knock values, and in the latter months of the year the public has been made acutely aware of this condition through competitive advertising. Gaso-line is no longer priced on volatility and gravity alone, but on octane number as well; and premiums are being paid for material of relatively high octane rating. The situation has grown more and more competitive and has forced refiners continually to raise the octane rating of their regular and com-petitive grades, and at this writing the same situation exists for premium grades which have possessed relatively high anti-knock properties for some time. Straight-run gasoline produced from paraffin-base or semiparaffin-base crudes has an inherently low anti-knock value, and in order to convert this material to a higher quality it has been found necessary to crack an increasing percentage of the crude oil charge. By completely cracking the heavier portions of the crude, and blending back with the straight-run gasoline, it has been possible to produce an average of 63 to 65 octane number gasoline' on average Mid-Continent crude. This operation carried to the fullest extent does not suffice, however, and the recent and rapid development of the so-called "re-forming unit," has resulted. The straight-run gasoline fraction is cut into two parts: a light, low boiling point gasoline; and a heavy gasoline or naphtha. The latter containing the low anti-knock portions of the gasoline, is sent through a re-forming unit and subjected either to high temperature ,or pressure, or both, which materially increases its octane number. On average Mid-Continent the blend of low boiling point straight-run,

Jan 1, 1932

By H. C. Stumpf, L. A. Willey, V. L. Fink

Very few studies of the aluminum-sodium system have been reported. Heycock and Neville1 were unable to detect any solubility of sodium in liquid aluminum. Mathewson2 prepared an equilibrium diagram consisting of two horizontal lines at the melting points of the two metals. He was unable to detect solubility at either end of the system. Scheuer3 first developed a method for the chemical determination of sodium in aluminum and then studied the solubility of sodium in liquid aluminum. His method involved heating aluminum with excess sodium under hydrogen until the two liquids were at equilibrium, chilling the melt, and analyzing the aluminum-rich layer. He reported the solubility to be 0.10 pct sodium at 700°C, 0.115 pct at 750°C, and 0.128 pct at 800°C. This paper on the aluminum-sodium system is the twenty-first in a series from the Aluminum Research Laboratories describing equilibrium relations in aluminum alloy systems. Materials The alloys for this investigation were prepared from electrolytically refined aluminum (99.99 pct) and sodium of reagent quality conforming to specifications of the American Chemical Society. Chemical analysis of the aluminum showed the fol- lowing impurities: 0.002 pct Si, 0.002 pct Fe, 0.002 pct Cu, <0.001 pct Mn, 0.002 pct Mg and 0.001 pct Na. The sodium content of all alloys was determined by either chemical or spectro-graphic standard procedures5 No. IIA and No. SI I respectively. Determination of Miscibilitv The boundary of the miscibility gap was determined by a modification of the method of Scheuer3 and of that used by Henry and Cordiano. As finally developed the method was as follows: A fused alumina crucible 25 mm id with 75 mm depth and 1.5 mm wall thickness was placed on the bottom of a container made from a 4-in. length of 1 1/2-in. iron pipe and pipe caps. ?&apos;he space around the sides of the crucible was filled with 40 mesh crystalline alun-dum. A charge of 60 g of aluminum and 10 to 15 g of sodium was placed in the crucible, the sodium first being trimmed and rinsed with iso-pentane to remove kerosene. The container was tightly capped, filled with argon (99.6 pct pure), and heated to the desired temperature (between 670 and 800°C). A positive pressure of argon (about 8 mm of mercury) was maintained through a small pipe to the upper cap. After soaking for from 2 to 5 hr, the container was quenched by directing a stream of water onto the base, so that solidification of the aluminum-rich layer was rapid and essentially unidirectional. Analyses were made on drillings taken from the bottom of the ingots after machining off the surface layers. Pre-

Jan 1, 1949

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By O. George Specht, Carl A. Zapffe

In recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge Iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experi- mentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. Group I: Reduction with Hydrogen Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1947

By Amos P. Brown

PYRITE, the bisulphide of iron, FeS2, is found more or less in all coal-beds: but, as a rule, in certain definite forms. More than any other impurity, it detracts from the commercial value of a coal-deposit, and yet its presence is so universal that it might almost be said that there is no coal entirely free from pyrite. My observation has been confined to the Pennsylvania bituminous and semi-bituminous coals, and to them, therefore, my remarks will be confined. Certain generalizations which I may make, however, will be found of universsl application. The lowest members of the coal-formation, No. XIII. of the Pennsylvania bituminous region, are nearly always pyritiferous, and in many cases highly so. In Cambria county, for instance, coalbed A, the Brookville, is locally known as the " Sulphur seam." The Lower Kittanning, in parts of Clearfield county, is so sulphury as to be almost unmarketable, though otherwise it is a strong locomohive coal. In Mercer county the Pardoe bed, so extensively mined there, carries great quantities of sulphur in the form of pyrite, though usually this can be separated in such a way as to detract little from the market-value of the coal. The other coal-beds of the Lower

Jan 1, 1888

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

At its meeting on February 21, 1933, the Board of Directors passed the following resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters: WHEREAS, the Board of Directors at its last meeting passed the following resolution: "The Board of Directors, having been appealed to by several Local Sections for advice concerning the attitude and policy of the Institute relating to the endorsement of candidates for public office, the following statement of

Jan 1, 1938

By C. V. O. Hughes

Florida phosphate operations are unique in the ways standard mining equipment is made to meet specialized problems. Hydraulic mining and transportation has evolved in meeting three such special problems: 1) surface mining of a shallow, poorly consolidated but wet material; 2) high pro¬duction rates, necessary because of low prices for phosphate rock in a highly competitive market; and 3) preparation of the value-bearing rock, or matrix, for washing and flotation. The magnitude of the problems is better appreciated if the reader understands the size of operations in the area. The Florida phosphate field produces and ships about 10 million tons per year of phosphate rock. All of this has to be concentrated to its shipping grade, either by scrubbing and screening or by flotation.

Jan 1, 1956

By C. W. Phillips, R. S. Busk

WITH most cast metals the grain size may vary within wide limits, depending upon the conditions at the moment of freezing. These conditions are subject to control in magnesium-base alloys, by proper melting and superheating techniques, enabling production of quite uniform and fine-grained castings, almost independent of section thickness. However, such variations of grain size as do exist, in common with all metals, are reflected in corresponding changes in mechanical properties. It is the intent of this paper to present data giving the relationship between grain size and mechanical properties. Data are also included on the combined effects of grain size and microporosity. In addition, a short discussion of factors influencing the grain size of sand castings is included. MEASUREMENT OF GRAIN SIZE By grain size is meant the statistical distribution of volumes occupied by the individual crystallites in a metal section. Since this is almost always impossible of direct measurement, several methods of estimating and expressing the size have been evolved. Most exact methods make use of the microscope. This involves study of a single plane cut at random through the metal. What is seen in the microscope are polygons, each the cross section of a grain. The diameters or areas of these polygons are then measured and the grain size is expressed as an average diameter, number of grains per unit area, average area per grain, or, rarely, average volume per grain. Rutherford, Aborn, and Bain3 have discussed extensively the errors involved when using a plane section to estimate volume. They clearly point out that the tendency is to underestimate the true grain size because of the nature of the measurement. The A.S.T.M.. recommends that measurement be made by comparison with a standard chart, by means of Jeffries&apos; planimetric method&apos; or Heyn&apos;s intercept method. The Society recommends that the notation be in terms of the number of grains per unit area (as is the grain-size number used for steel) or as an average diameter, expressed in inches or millimeters (as for copper and brass). The method of measurement used for this study was comparison with a standard chart, which has been described by P. F. George.&apos;, The chart was constructed by photographing at i00 diameters a uniform specimen with an average grain diameter of 0.003 in. The average diameter of this specimen was determined by numerous measurements, using both the Jeffries and Heyn methods. The other grain sizes were then obtained by appropriate enlargement of the master sample. Careful comparison of the chart method with other methods on identical samples indicates that though the differences be-

Jan 1, 1945