Search Documents

By John G. Hall

The unstable metal market during 1949, with resulting lower metal prices, has focused every mine operator's attention on the problem of reducing operating costs. Improvement in mining, methods, use of modern mechanical mining equipment, and increasing the efficiency of the labor force are the tools with which we will have to work. Careful planning is necessary to coordinate all phases so that no one phase is overdone. A mine may become over-mechanized if, for instance, capital charges against new equipment exceed the savings in labor costs, or where a large enough tonnage is not produced. The cooperation, of labor is essential to any mechanization program. There have been too many instances where mechanization and improvements have done nothing more than make up for a decrease in labor efficiency, thus bringing the production of labor back to its old standard. The operator has gained little and labor has gained only a "softer job." In any mechanization program there are gains to be had by both the operator and labor. By the efficient application of modern equipment and improved mining methods the operator should gain by decreased costs, and labor may profit by receiving a share of these decreased costs.

Jan 1, 1950

By Harold B. Fell

MANY oil producers are in disagreement with the idea held by some that an increase in the price of crude oil would be unlikely to stimulate much production and that we will be obliged to draw upon foreign sources of petroleum to supplement our domestic production as the years go by. Supporting our con trary opinion are numerous facts and figures. The most recent official estimate of the maximum efficient rate of production from the oil wells of the United States is 5,271,000 bbl per day. The Economics Advisory Committee of the Interstate Oil Compact Commission estimates, assuming certain supplies from imports and from natural gasoline and benzol, that crude oil require-

Jan 1, 1947

By W. C. Bednar

In all, 127 producing oil wells, 8 producing gas wells and 212 dry holes were drilled during 1936 in the Central Texas area; 76 wells in Bexar County, 62 in Caldwell County, 44 in Guadalupe County, 22 in Williamson County, 20 in Navarro County and 20 in Frio County. Less than 20 were drilled in each of the other counties and none at all in Ellis, Hill, Bosque, Coryell, Lampasas, Burnet, Llano, Kennedy, Mason, Real, Kinney and Uvalde Counties. The Pearsall-Austin chalk field in Frio County and the Zoboroski field in Guadalupe County were the only new discoveries and there were no important extensions to old fields. In this report Corsicana, Mildred (Elm Ridge), Angus-Edens-Hodge, Burke, and Rice-Oil Ridge, all shallow Navarro County stripper fields, are grouped together under the name of Corsicana. This grouping follows that of the Railroad Commission of Texas, thus facilitating the gathering of production data. A map showing the location of the oil and gas fields in the Central Texas Area was published in Volume 114 of the A.I.M.E. TranBactions, page 380. New Fields Pearsall-Austin Chalk.—The Amerada Petroleum Corporation completed 13 Austin chalk wells during 1936 on the large Amerada-Rycade block in Frio County. Other companies drilled two dry holes to the Austin chalk in this vicinity. Not enough wells were drilled to give control of the structure but it appears to be a nose plunging in a west-southwest direction. A second deep test is being drilled in the Pearsall area and at this writing has cemented off a show of oil and gas in the Edwards limestone. The Humble Oil and Refining Co. is building a 6-in. pipe line from Lytle, Tex., to serve the Pearsall field. Zoboroski.—Actual discovery of the Zoboroski field was made by W. J. Walton et al. in 1931. The discovery well, Anton Zoboroski No. 1, was a small producer making but from 3 to 5 bbl. per day, which was used locally for fuel oil. The discovery of the Darst Creek Extension in

Jan 1, 1937

[Alphabetic Section: The letter immediately following a member's name indicates grade: M-member, A-associate, J-junior. The numerals following member's grade indicate year of election. The letter following year of election indicates primary divisional affiliation: A. Mining & Exploration F. Coal B. Minerals Beneficiation G. Petroleum C. Iron and Steel H. Industrial Minerals D. Extractive Metallurgy J. Council of Education E. Institute of Metals K. Council of Economics Geographic Section: An asterisk (*) preceding a member's name indicates availability for consulting work:]

Jan 1, 1961

By D. T. Van Zandt

IN the late 1920's rotary drills began to replace the churn drills in the petroleum industry, but until the middle 1940's the churn drill was the only widely accepted means of drilling large-diameter blastholes for quarry operations. The Calcite plant of the Michigan Limestone Div., U. S. Steel Corp., was one of the first to experiment with rotary drills for quarry blasthole drilling, and the first to employ compressed air on a fully rotary rig to cool the bit and raise the cuttings to the collar of the blasthole.

Jan 8, 1954

By H. Wilhelm, E. L. Davis, W. A. Clark

MATHEMATICAL formulas for the analysis of the behavior of producing oil wells can be devised which will be correct for the assumed conditions. However, in an oil zone, variables always exist which are unknown, or to which. it is impractical to assign mathematical values. It seems apparent that one should reason back from observed facts to an analysis of causes, rather than start with a hypothetical reservoir with assumed properties and attempt to explain observed phenomena. In this paper we hope to throw some additional light on factors influencing production, especially edgewater behavior. OIL and gas are contained in reservoirs of either the sealed type or the edgewater type. In the former all the recoverable oil is produced by gas expansion only. In this type of reservoir, edgewater is not effective. This may be because of faulting or overlapping strata, or more often, probably, the edgewater pressure is ineffec¬tive on account of resistance or lack of head.

Jan 1, 1933

By John Burns

THE object of this chapter is to present data concerning the effect of the introduction of relatively slight amounts of carbon and nitrogen into supersaturated solution in iron. The study is confined to the alpha temperature range of both the Fe-C and Fe-N systems. The age-harden-ing characteristics of these two systems are considered. These data are compared to those of other age-hardening alloy systems and a "classifica-tion" is essayed. A.-RELATION OF LATTICE PARAMETER AND ELECTRICAL CONDUCTIVITY TO CHANGES IN PHYSICAL PROPERTIES DUE TO AGING OF FE-C ALLOYS Since Whiteley1 in 1927 showed that some of the iron carbide that is normally present in slowly cooled low carbon-iron alloys disappears on rapid cooling from just below the A1 point, interest has been manifested in the possibilities of age-hardening in these alloys. Masing and Koch,2 and at the same time and independently, W. Koster,3 proved these alloys to be age-hardenable. A. A. Bates4 a little later also published an interesting paper on changes in physical properties due to the aging of low-carbon steels. Many other papers have appeared showing changes in physical properties in specific instances due to this same phenomenon.

Jan 1, 1934

By Reginald S. Dean

THE commercial availability of electrolytic manganese has greatly changed the position of manganese as a nonferrous alloying metal. Manganese metal commercially available up to about ten years ago was reduced with either silicon or aluminum and contained substantial amounts of the oxides of these metals and other impurities. Manganese was accordingly not available as an alloy base and its addition to copper-base and nickel-base alloys was generally limited to a manganese content of a few per cent. Several special alloys like manganin contained up to 12 pct of manganese. A method for the production of electrolytic manganese was developed by the Bureau of Mines in 1936 and commercial production was begun in 1938. At the present time (June 1951), production is about 12 tons per day but appears likely to be substantially increased. Electrolytic manganese is deposited from an aqueous electrolyte containing manganese and ammonium sulphates and is marketed as cathode fragments about 1/8 in. thick. The impurities in its composition are as follows: iron, 0.0015 pct; copper, 0.001; arsenic, 0.0005; cobalt, 0.0025; lead, 0.0025; molybdenum, 0.001; sulfide sulfur, 0.017; sulfate sulfur, 0.014; insoluble, 0.002; carbon, 0.002; hydrogen, 0.015. These figures are from Bulletin 463, U. S. Bureau of Mines. From an alloying standpoint, the most important impurity is hydrogen. This can be removed by heating; 95 pct of the hydrogen can be removed in this way without introducing significant amounts of oxygen or nitrogen. Much of the commercial electrolytic manganese used in alloys is dehydrogenited by the producer, since the amount

Jan 1, 1953

By D. L. Albright, R. W. Kraft

A technique is described whereby the study of crystal perfection through the use of conventional X-ray rockite curves is extended to three dimerzsions. Specinzens of unidirectionally solidified eutec-tic alloy which consist of a nearly perfect parallel arrangement of alternating Platelets of Al and CuAl2, but which contain lamellar faults have been analyzed by this technique in conjunction with X-ray microscopy. Analysis of the data has shown that some rotational symmetry about the growth direction occurs, that small groups of lamellae between faults diffract as a unit, and that the misorientation caused by a fault is on the order of a degree of arc. A eutectic-grain can be defined as that portion of a eutectic specimen in which the crystallographic orientation of each phase AND the microscopic or met-allographic orientation of the phase particles have fixed angular relationships one to another. Eutectic-grains of the A1-CuA12 eutectic, which is a normal lamellar eutectic, have been grown by unidirectional solidification and identified as such.1-3 To a first approximation, a eutectic-grain in this system consists of two interpenetrating single crystals which are related to each other and to the lamellae themselves as follows:

Jan 1, 1962

The Hadsel Mill. By R. G HALL (Trans, vol 112 4000 words) This mill is designed to effect the entire reduction of ores by combined crushing and grinding from mine run size to material sufficiently fine for the usual operation of flotation or cyaniding The work is begun and completed in the same machine. The machine is designed on the principal of the elevator wheel, and crushing and grinding are accomplished by dropping a mixture of ore and water upon specially placed "breaker plates" in such a manner that the resultant material passes back into the buckets of the wheel for further elevation One method of removal of the finished product is to permit an overflow of wet pulp on one side of the mill through coarse screens A recent improvement provides for the removal of a pulp by a launder part way up the path of the buckets In either case the pulp passes to a classifier, and the oversize back to the mill in the manner familiar in ball-mill practice Although hardly through the development stage, the machine has given a very good account of itself in simplification of plant, by elimination of coarse and fine crushers with consequent reduction of installation cost and power consumption As compared with the ball mill alone, there is a reduction of power consumption as well as a material reduction of grinding steel There is an increase in cost of maintenance other than grinding steel, but as the machine passes out of the development stage there is a show¬ing of reduction of costs on this item It seems probable that with further develop¬ment and strengthening of the weaker parts further improvement may be made Ball Milling. By A. M Gow, M GUGGENHEIM, A. B. CAMPBELL AND W. H COGHILL. (Tech Pub 517; also Trans, vol 112. 24,000 words) This paper outlines a new philosophy in ball milling by using power as an index of mill operation and ascertaining the effects of the set and induced variables By recognizing the amount of ore in the mill as an important induced variable and recognizing that the amount of ore in the mill depends principally on the size of the discharge trunnion, ball volume, rate of feed, and speed of mill, obstacles formerly met were surmounted When the amount of ore in the mill is dealt with intelligently and the applied work is proportional to the amount of feed, series testing, which would otherwise give a hotchpotch, gives concordant results The study of ball paths and trajectories was seen to be fruitless when it was shown that the old attrition theory for slow mill speed

Jan 1, 1935

By A. A. Brant

Mining men, quite as exploration minded as petroleum interests, are in the position where most of the exposed crustal portions of the earth have been examined, where the demand for metals is high and likely to continue so, and yet where, perhaps, the tools fail for the economic exploration of many of the possible mineral areas more deeply covered with drift, alluvium, and later formations. At the same time the incentive exists to create acceptable substitutes for many of the duties of metal. The problem of the economic exploration of possible mineral-bearing areas is hence a vital one. In oil exploration, the absence of surface or shallow occurrences and the high cost of test drilling has led to the intensive study of geophysical techniques. Hence the development of the seismic method with its high certainty factor and its adaptability to standardized procedure.

Jan 1, 1949

By Clemens Jones

The peculiar property of the lode-stone has been known for many centuries. It was very early observed that, by contact with it, iron is magnetized; and it is needless to dwell here upon the history allied to this discovery, now constituting the wonderful science of magnetism. Deposits of magnetic ore are distributed all over the world. The ore is sometimes very rich and comparatively free from gangue, sometimes sparsely disseminated in the native rock. These bodies of lean ore often cover large areas. Modern ingenuity has utilized the principle of the magrtet, originally derived from the ore itself, and really belonging to the time of Plato and Theophrastus, to separate the magnetic ore-particles from the rock which has previously been crushed. This process recovers the ore in the state of a concentrate very rich in iron and, in some cases, desirable for Bessemer purposes. The magnetic separator is no longer a novelty. It was only at the last meeting of the Institute in New York, that Messrs. Birkinbine and Edison (Trans., xvii., 728) and Mr. Robert Cook (Ib., 599) described some of' the principal designs of apparatus in use. E. S. Dana classifies the natural magnetic minerals in the following order: magnetite, pyrrhotite, franklinite, almandite and minerals " containing considerable FeO." Of these, ferroso-ferric oxide, or magnetite, is the type. The proportionate amount of ferrous oxide essential to magnetize the compound, is not established. Ferrous oxide appears to be the only magnetic oxide of iron. Tissandier (Compt. Rend., lxxiv., 531) produced ferrous oxide in the anhydrous state, by the action of carbon dioxide on pure iron at a red heat, according to the equation : Fe + CO2 = FeO + CO. This is black, crystalline and magnetic. Heated to redness in the air, it is converted into Fe3O4. Sidot (Compt. Rend., lxvii., 175) has also produced an oxide exhibiting magnetic polarity, by heating ferric oxide to a temperature

Jan 1, 1891

By L. E. Welch, C. W. MacGregor

THE past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared to the long-time creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling,' forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has. been pointed out 1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied [ ] under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses, and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1942

By E. C. Herkenhoff

THIS subject may be controversial. Personal preferences influence the final selection of cyclones, and side issues such as costs, floor areas, head room, and ease of replacing worn parts all enter the picture, but the following comments and data should apply to most cyclone selection problems. Broadly, the uses for cyclones in wet classification may be divided into three fields: 1) Open circuit operation, for two products, in which feed rate and sizing vary and the products vary. For example, feed may be divided into a sand product and a slime product. 2) Open circuit operation, for two products, in which feed varies, one product to have constant sizing. This calls for adjustment in either the apex or the vortex aperture. 3) Closed circuit operation, the finished product to have constant sizing. Most classification jobs fall in this category.

Jan 8, 1957

By L. K. Welch, C.W. Macgregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By L. K. Welch, C. W. MacGregor

The past 20 years has seen a revolutionary change in the testing of materials at elevated temperatures. This has largely been brought about by the practical importance of the creep problem in the design of equipment for operation at high temperatures. The short-time tension test carried out at elevated temperatures has consequently assumed in many cases only a secondary role compared with the longtime creep test. In many problems, however, a knowledge of the short-time high-temperature properties of a metal is essential. To mention a few cases in which this is so, we might include all hot-forming operations such as rolling, forging, etc., the welding problem if residual stresses are to be computed, the development of new alloys for high-temperature service where, in the initial stages, time does not permit of long duration creep tests, and others. Usually a knowledge of the short-time properties is desired, if only to serve as a background against which to compare creep behavior. In conducting short-time high-temperature tests, it has been almost the universal practice to determine stresses based on the original area and strains referred to the original gauge length which is usually chosen as 2 in. It has been pointed out1,2 that one of the reasons that the true significance of certain tensile properties is not understood, which perhaps curtails their usefulness, especially when the material is applied under conditions differing considerably from the test conditions, is that true physical stresses and strains are not determined. It is essential to have a knowledge of true stresses and strains in order to correlate the values present in the tension test with those existing, for example, in hot metal-forming operations and in the general problem of the yielding and failure of metals under combined stress conditions. Stress and strain values based on the original dimensions of the test piece do not exist physically except in the early stages of the test. Since at the present time there is very little information in the literature on true stress-strain relations in the short-time high-temperature tension test it is proposed in the following pages to describe a

Jan 1, 1943

By AIME AIME

BERYLLIUM is one of the most interesting of the minor metals and distinctly a modern development, for until the last two decades it had practically no commercial importance whatever. Then it was discovered that when small quantities of it were alloyed with copper, a copper alloy of unusual and valuable qualities resulted. This is by far its major use-in the manufacture of strong, heat-treated copper-base alloys in which the beryllium content varies from about 0.3 to 2.5 per cent. Its second most important use, though much smaller, is in the form of oxide or other nonmetallic products in the fluorescent lamp, X-ray, cathode ray, and television industries. Certain beryllium salts have the quality, in common with several other materials, of transforming short-wave radiation and cathode rays to visible radiation. Such materials are commonly known as phosphors, and the beryllium salts are the most important phosphors now in use. The third largest use for beryllium is for ceramics, including refractories. Beryllium is also used in small quantities in the form of the metal itself.

Jan 1, 1943

By B. B. Sandiford

It has been known for many years that the efficiency of a water flood can be improved by lowering the water-oil mobility ratio in the system. Such a change leads to better sweep efficiency and also to more efficient oil displacement in the swept zone. Data from our laboratory water-flood tests of both small cores and long sand packs are presented which show that water mobility can be reduced and oil recovery increased by the addition of certain polymer solutions to flood water. The reduction in mobility, in many cases, is greater than would be expected from conventional viscosity measurements. These solutions, however, do not cause significant reductions in oil mobility. The over-all effect of these mobility changes is increased waterflood oil recovery. Encouraged by results of our laboratory work, we expanded our study to include pilot field tests of floods with such solutions. One such test, made in the West Cat Canyon field, Santa Barbara County, Calif., is described in detail in this paper. Three other field tests are also discussed. INTRODUCTION Oil production from most reservoirs following primary depletion and/or water flooding is often less than 50 per cent of the original oil in place. Heavy oil reservoirs seldom yield over 15 per cent of their original oil. With new reservoirs becoming harder to find, the improvement of oil recovery efficiency is one of our very important problems. We describe here some of our attempts to increase the efficiency of oil displacement by adding a water-soluble polymer, partially hydrolyzed polyacrylamide, to flood water. This technique will be termed "polymer solution flooding". The concept of using high-viscosity water to increase the efficiency of water flooding is not new. In 1944 Detling (Shell Development Co.) obtained a patent covering the use of several additives for viscous water flooding.' His objective was to improve water-oil mobility ratios by increasing the viscosity of the flood water. Other patents2-27 have been granted covering specific water-SO~LIble polymers or specific conditions of viscous water flooding. Barnes'" described his laboratory model study of the injection of a viscous water slug into a reservoir which had been partially invaded by bottom water. He concluded that, for this type of reservoir, "the cost of viscous water should not exceed a few cents per barrel for viscous water slug injection to be economically feasible" Our studies have led us to a somewhat different conclusion in a number of cases where hydrolyzed polyacrylamide solutions have been injected into reservoir models or actual reservoirs. Possible reasons for this difference are discussed in this paper. Our studies have shown that polymer solutions may lead to an increase in oil recovery over that from an ordinary water flood by (1) improving sweep efficiency, (2) improving microscopic displacement efficiency, or (3) a combination of these mechanisms. In the work of Barnes, only the benefit of improved sweep efficiency was considered. Also, our work has shown that there are marked differences in the effectiveness of different water-soluble polymers as flood water additives. Partially hydrolyzed polyacrylamide is better than many other water-soluble polymers we have tested because, even in very low concentrations, it can lead to increased oil recovery. This is an important advantage when either a dilute polymer solution is injected continuously or a relatively concentrated slug is injected followed by water. In the latter case! portions of the slug become diluted and function in the formation as very dilute solutions. As dilution takes place the effective slug size will increase which, in turn, will reduce the cost per barrel of the effective flooding medium. The reason that partially hydrolyzed polyacrylamide solutions are more efficient at low concentrations than certain other polymer solutions of equivalent viscosity (when measured in conventional viscometers) is not fully understood. We do know that the shapes and sizes of macro-molecules dissolved or suspended in liquids influence the flow properties of their solutions or suspensions. Solutions of partially hydrolyzed polyacrylamide cause greater reductions in water mobility than would be expected from conventional viscosity measurements. LABORATORY STUDIES Laboratory water floods were run in linear and radial systems with different water-soluble polymers and under varying conditions of flow. including reservoir conditions of temperature, pressure and fluid composition. Some of these runs are considered in this section. OIL DISPLACEMENT IN LINEAR MODELS In this group of runs the sweep efficiency approached 100 per cent because the linear sand packs used were as nearly uniform as possible. Results reflect primarily the micro-scopic displacement efficiencies. The laboratory models were unconsolidat-ed sand packs the lengths of which varied from about 4 in, to 40 ft. Further information on the flow models used is listed in Table 1. Using conventional procedures, water floods were run on sand packs containing either refined or crude oil at restored state. Frequently, a repeat run, similar to the first, was made as a check. Then a third run was made on the restored-state model using either polymer solution or a combination of polymer solution (slug) and water. Details of these runs are also reported in Table 1. In Figs. 1 and 2 results of two different groups of runs are shown in which the oil used was a 62-cp refined oil and the flooding medium

Jan 1, 1965

By W. E. Horst

John Dasher (Central Research Laboratory, Crucible Steel Co. of America, Pittsburgh. Pa.)— Getting spodumene to float quickly and cleanly can be a problem. The author has presented an excellent account of a valid and useful approach to the scale-up of such problem floats. This indicated advantages for doubling retention time, i.e., buying another set of flotation cells. The author states that 21 pct of the spodumene floated in 2 min in the laboratory cell, that the grade of the rougher was about 75 pct spodumene, and that the final tailing contained 4 to 12 pct spodumene in different sizes with the present cells and 1 to 9 pct spodumene with twice as many cells. About 20 years ago, this writer obtained in the laboratory the flotation of over 90 pct of this spodumene in a King's Mountain sample in 1 min at a grade of 90 pct spodumene in the rougher and a final tailing that contained only 1 pct spodumene. The methods of Norman, Ralston," and Gieseke' were used, which teach that spodumene floats quickly and cleanly if its surfaces have been properly conditioned chemically and/or mechanically prior to flotation. Although feed preparation is not discussed, the results reported indicate that it is inadequate. This writer suggests that improvements in this area might be more effective than doubling the number of cells. W. E. Horst (author's reply)—Dasher's comments are appreciated by the author and require some clarification. He suggests that improved spodumene flotation performance may be obtained by feed preparation techniques rather than increased retention time in flotation. Certainly flotation performance is dependent on feed preparation and this is an important feature in the flotation process. It is true that certain types of spodumene ores, particularly weathered ores, require more complicated feed preparation processing than clean ores to achieve the desired flotation results. It was not implied that current feed preparation techniques are the same as experienced during the scale-up investigations. Although discussion of feed preparation was omitted from the article on scale-up relationships, the important feature was that pre-treatment processing was the same for each level of operation investigated— laboratory, pilot plant, and plant scale. Under these similar conditions large differences existed in recovery for comparable time intervals in each scale of operation. It is highly probable that feed preparation techniques could be modified and thereby increase the flotation rate for each scale or all scales of operation discussed. However, modifications would have to be justified on an economic basis.

Jan 1, 1960

By AIME AIME

As already announced in the January Bulletin, this publication will be issued during the coming year monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates for membership, and other items of timely information. Spokane Meeting and Excursions. Further details of the' 97th meeting of the Institute have been sent to members in the Circular of May 8, 1909. For, convenience of the members a summary of the additional in¬formation is here presented. A special train of Pullman cars will leave Chicago about September 15. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals during the entire trip, except during the Yellowstone Park tour. The general. cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through Yellowstone Park, occupying in all about 30 days. Special accommodations on the train will be furnished at the following, rates

May 1, 1909