Search Documents

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By G. S. Hume

Production of petroleum and natural .gas increased in Canada in 1940 over the previous year. Alberta produced more than 97 per cent of the total Canadian production of 8,718,053 bbl. of oil, an increase for this province of nearly 12 per cent, whereas in Ontario and New Brunswick, where the production is relatively small, there was a slight decline. In Alberta the main producing field is Turner Valley, on the eastern edge of the foothills southwest of Calgary, and development continued in this field in 1940 with the completion of 36 wells, all of which obtained production. In the Red Coulce field, close to the International Boundary, near Coutts, no new wells were drilled and the seven producing wells showed a decline of 900 bbl. below the previous year. Also, in the Wainwright field of east central Alberta, four wells, yielding heavy crude oil, produced 4000 bbl. less oil than in 1939, owing possibly rather to discontinuous operation than to actual decline in potential yield. This decline was more than offset by production from a new field 40 miles northeast of Wainwright, at Borradaile, producing oil of 14" to I 5° A.P.1. There was a small increase in production during 1940 from the Del Bonita field, in southern Alberta, where the production is from two wells. The outstanding development of the year was the completion of Standard Oil Princess No. 2 well in the Steveville area, on the Plains 100 miles east of Calgary. This well was completed late in December with an initial flow1 of 520 bbl. of 26.3" A.P,I. oil, and 12,750 M cu. ft. of gas from the upper part of the Mississippian limestone. It has opened up a new field and given a further proof of the potentialities of the Southern Plains. The production of petroleum in Canada is shown in Table I. Since most of the yield comes from Alberta, the production is shown from the various fields in Table 2. The sale value of the petroleum produced in Canada in 1940 exceeded 11.1 million dollars, which is still somewhat less than the value of the natural gas production, shown in Table 3. Table i.—Production of Petroleum in Canada" Barrels Province 1939 1940 New Brunswick........ 20,101 21,161 Ontario............... 206,196 186,471 Alberta............... 7,595,000 8,493,237 Northwest Territories. . 17,013 8,493,23717.184 Total............... 7,838,310 8,718,053 Value............... $10,353,351 $11.113,000 0 Bureau of Statistics, Ottawa. Turner Valley, Alberta Turner Valley continues to be by far the largest producing field in Canada (details are given in Table 4), The limits of the Pr in- field are now Known. On the east the oil area is bounded by the gas cap, which in turn is cut off on its east side by a major overthrust fault; on the west, ii is defined by edge water at a level of 4roc

Jan 1, 1941

By Earnshaw Cook, J. A. Fellows, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

By J. A. Fellows, Earnshaw Cook, Howard S. Avery

Heat-resistant alloys of the higher nickel and chromium ranges have been empirically developed through the practical experience of the past two decades to a position of significant industrial importance. Few quantitative metallurgical data have been published, however, that could be related directly to engineering specifications and design. Inadequate information led to the inauguration, in 1934, of a research directed toward a better understanding of the properties and performance of these steels at temperatures between 1400° and 2000°F. Investigation was concentrated upon the 26 per cent Cr:I2 per cent Ni type, which owes its extensive application to an excellent combination of economy, strength and surface stability at elevated temperatures. The requirements of the oil-refining industry have been prominent in influencing the scope and evolution of the program. Creep strength at the maximum allowable deformation ranges has been employed to evaluate the merits of these alloys. Permissible elongation rates vary from 1.0 per cent in one million hours for turbine blades to I .o per cent in ten thousand hours for tube supports and heating-furnace equipment. Throughout this paper, the limiting creep stress (L.C.S.) for a given temperature has been defined as the stress that will produce a uniform elongation rate (stage 11) of one per cent in ten thousand hours as extrapolated from rates per hour for tests of less than two thousand hours duration. Certain current specifications require a minimum L.C.S. of 1600 lb. per sq. in. at I800°F., of 3600 lb. per sq. in. at 1400°F., and include a tensile acceptance test at room temperature, after aging for 24 hr. at 1400°F., as a measure of embrittlement in service. An elongation of 4 per cent is considered satisfactory for general use, while a minimum of 9 per cent is prescribed on occasion. Many differences of opinion concerning the properties and performance of these alloys appear to result from their sensitivity to unappreciated variations of chemical analyses which, for example, may change their L.C.S. from 3500 to 350 lb. per sq. in. at 1800°F. Within broad chemical limits, it is possible to balance the six or more important elements present to attain desirable properties with a number of different combinations. One method for adjusting the composition has been described under the sponsorship of the Alloy Casting Institute,' in which, by maintaining a substantially austenitic* alloy, optimum creep strength and minimum tendency to embrittle after aging are expected. Unless, however, the limits are undesirably close, it has not been possible to ensure a moderate range of strength and of ductility by any chemical specification alone. There is a definite need

Jan 1, 1942

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons introduced by members) Member, Graduate Colorado School of Mines. Four years' experience in West and Northwest. Two years with American Smelting and Refining Co. Wishes to join field party on geological work, mining or areal, where opportunity will be given to be of direct assistance to chief of party in solution of field problems. Age, 26. Unmarried. At liberty June 1. No. 342. Member, technical graduate, aged 30, with' 7 years' experience in concentrating and mining, desires a position of authority with reliable company. At present employed. No. 343. Member. Ambitious, energetic, tactful engineer, college graduate, married, aged 30, desires location with a large coal mining organization. Seven years with present employers -n middle west; has had broad experience in the past eight years on examination, development and construction; successful record in handling men. Position must carry responsible work and a future. Will go anywhere for proper opportunity. Exceptional references as to reliability, character and capacity for work. No. 344.

Jan 3, 1917

By James Gayley

(Wilkes-Barre Meeting, June, 1911.) THE paper presented to the Institute in 1910, by H. 0. Hofman, on Recent Progress in Blast Roasting,1 has called the attention of the iron industry to the adaptability of these processes to the reclamation of by-products such as flue-dust and blue billy, and the better preparation of concentrates and fine ores for use in blast-furnaces. The waste of valuable iron-ore through the production of flue-dust has increased at an enormous rate, and much of it has in reality been wasted as far as future recovery is concerned. Only in recent years has a possible future value been recognized, and the material stored. The increased use of Mesabi ores, which carry considerable fine ore, is principally responsible for the great increase in the production of flue-dust. The amount of fine material that is carried over depends on the fineness of the material and the velocity of the gases, and also to a very great extent on the regularity or irregularity of the working of the furnace. Attempts to recover a part of this loss have been made by recharging a portion of the production into the furnace, but as this material has been once carried out from the furnace, it is naturally in good shape to be carried out again. A recent practice at some works, is to soak the flue-dust thoroughly with water to give it more cohesiveness, but by many this is considered of doubtful advantage in the furnace, and the gases are in consequence heavily laden with moisture. There are vast deposits of magnetic iron-ores in the United States and Canada that are too low in iron for use at the present time, but which can be economically concentrated into very rich material ; in many cases the fineness of crushing necessary to secure proper concentration has prevented their

Aug 1, 1911

By Thomas T., Read

IT does not seem practicable to review all the other specialized curricula that have developed in the mineral industries field in so much detail as has been given for petroleum. Nor is it easy to draw a definite line between true curricula, leading to a designated degree in the special subject, and options, which may range from the mere substitution of one or two courses for others ' in the final years to differences so extensive as almost to amount to separate curricula. Even to attempt to catalogue all the options that have been offered at one time or another would , require too much space. The remainder of this discussion, there- fore, will be confined to three topics which seem to be of major importance. Mining and metallurgical curricula will be covered in a later chapter. Geology The first, from the historical view, is geology in its relation to the mineral industries. Previous, chapters have made clear that in the early years of mineral industry instruction in the United States economic geology and mining engineering, so overlapped one another that men who were by training and experience economic geologists were appointed professors of mining, while men who had graduated as mining engineers sometimes developed into professors of geology. Even today men whose basic training was in- geology as a pure science, and who perhaps took a doctor's .degree in that subject, have attained such distinction in the mineral industries as to be universally accepted as "mining men," and their right to be regarded as mining engineers would not be questioned, even though 'they did not .take a degree in engineering. Nevertheless the distinction does exist, and has been made a concrete reality in recent years by the enactment of

Jan 1, 1941

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation's oil-producing states, Oklahoma's output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year's total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year's figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42' gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

By Raymond D. Sloan

Retaining third place in crude-oil production among the nation's oil-producing states, Oklahoma's output in 1942 totaled 137,792,000 bbl., a decline of 9.4 per cent from the previous year's total of 152,117,000 bbl. Production declined from an average of 403,000 bbl. daily in January 1942 to an average of 355,000 bbl. during December, a reduction of 48,000 bbl. daily (11.9 per cent) during the year. At the end of 1942 it would appear inevitable that the downward trend in production will continue in 1953 unless halted in the immediate future by greater than normal discoveries and development. To Jan. I, 1943, Oklahoma has produced 5,067,013,000 bbl. oil crude oil. Development and Exploration Development dropped abruptly in 1942, reflecting the lack of any sizable discoveries and the effect of the provisions of Federal Well Spacing Order M-68, which became effective in December 1941. In all, 1210 wells were drilled in 1942. This represents a decrease of 42.7 per cent from the 1941 total of 2110. Of the total wells completed, 553 (45.7 per cent) were oil wells with an average initial production of 443 bbl.; 102 (8.4 per cent) were gas wells with an average initial of 3,359,000 cu. ft.; and 555 (45.9 per cent) were dry. Although the number of completions declined sharply, the total of 320 wildcats completed (26.4 per cent of all wells) repre-sents a decrease of only 2.7 per cent from the previous year's figure of 329. Of the wildcats drilled, 44 (13.8 per cent) were oil wells, 13 (4.0 per cent) were gas wells, and 263 (82.2 per cent) were recorded as failures. Reconditioning of wells throughout the state resulted in a total recompletion of 355 wells. Of these, 234 were oil wells with a combined initial production of 96,808 bbl., 32 were gas wells with a total initial of 381,488,000 cu. ft., and 89 were abandoned. None of the 26 pools found in 1942 has developed into a major discovery. The Pauls Valley pool, Garvin County, is the most outstanding. Since its discovery in April, 14 wells with an average initial of 1898 bbl. have produced 803,000 bbl. of 42' gravity oil from the Bromide zone. Development in this pool is believed to be almost completed. Other of the more important discoveries are the East Watchorn pool, Pawnee County; Guthrie Townsite and West Navina, Logan County; Brooksville and Macomb, Pottawatomie County, and the Liberty and Northeast Lucien discoveries in Noble county. The East Watchorn pool, at the close of the year, had 14 completed oil wells with an average initial of 989 bbl. from the Wilcox sand at 3930 it.; Guthrie Townsite, one well with an initial of 840 bbl. from dolomite at 5600 It.; West Navina, six wells with an average initial of 284 bbl. in the Lay ton sand at 5050 ft., Brooksville, eight wells in the Hunton at 4800 ft. with an average initial 01 355 bbl.; Macomb, one well with an initial of 160 bbl. in the IIunton at 4700 ft.; the Liberty pool, one well with an initial of 1268 bbl. in the second Wilcox at 4500 ft., and two wells in the Tonkawa sand at 2500 ft., with an average initial of 230 bbl. In the Northeast Lucien pool, four wells were completed in the Wilcox at 5380 ft. for an average initial of 1164 bbl., and one well was completed in the Viola lime at 5255 ft. for an initial of 55 barrels.

Jan 1, 1943

By J. A. Gay

BRITISH success in extracting significant quantities of germanium from gas works flue dusts has been one of the prime forces in promoting similar research in the United States. Pittsburgh Consolidation Coal Co. and Pennsylvania Coal & Coke Co. are two of the larger U. S. firms with germanium from flue dust research programs. British interest in germanium started in 1933 when V. M. Goldschmidt reported that some coals from the Yard Seam of Northumberland and Durham contained 30 to 50 ppm of germanium.

Jan 8, 1953

By Gerald G. Griswold, James O. Greenslade, Cherie Tilley, Richard Reseigh

INTRODUCTION The Harrison Western Corporation, a leading Denver based mine contracting and engineering concern, is presently engaged in sinking two 1,006 m (3,300 ft) shafts for the Phillips Uranium Corporation at their Nose Rock Project, approximately 13 miles northeast of the small community of Crownpoint in McKinley County, New Mexico. The Nose Rock Project is the first attempt by the Phillips Uranium Corporation to tap the deep uranium reserves in what has become known as the Grants Mineral Belt. (See Figure 1) Project Description Phillips Uranium Corporation's plan for the large 2700 metric ton per day (2950 tons/day) mining facility calls for a series of deep access and ventilation shafts ranging from 4.27 m (14 ft) to 5.49 m (18 ft) in diameter to approximate depths of 1,006 m (3,300 ft). The initial pair of shafts consists of one production shaft and one ventilation shaft separated by a distance of 91 m (300 ft). The interbedded layers of sedimentary sandstones and shales to be penetrated by the shafts contain several major water producing aquifers, the deepest being the mineralized zone called the Westwater Canyon Member of the Morrison Formation. A series of temporary and permanent water pumping stations is planned. Generally, the temporary stations are located above major aquifers to facilitate water removal while sinking through the aquifer and the permanent stations constitute what, in the final mode, will be the mine dewatering system. In addition, Phillips Uranium Corporation has In- stalled and is maintaining a system of depressurization wells that temporarily pump the major aquifers and considerably reduce the water inflows during shaft construction. The major aquifers are also chemically grouted prior to sinking. Site work for the project was initiated in the fall of 1976. Full scale shaft sinking commenced in November of 1977 on the 4.88 m (16 ft) diameter ventilation shaft and on the 5.49 m (18 ft) production shaft by another contractor. Harrison Western Corporation began work on the project on November 4, 1979 wlth the production shaft at a depth of 633 m (2,076 ft) and the ventilation shaft at a depth of 474 m (1,554 ft). This paper will address only the portion of shaft sinking completed by Harrison Western. Geology and Hydrology The Nose Rock Project is located on the Chaco Slope in the southern extreme of the San Juan Basin in northwest New Mexico. The southern San Juan Basin is generally bound by the Defiance Uplift to the west, the Zuni Uplift to the south and the Nacimiento Uplift to the east. The Grants Mineral Belt occupies most of the southern portion of the San Juan Basin and this project is located on the northern extreme of the Grants Mineral Belt. The San Juan Basin is comprised of sedimentary rock of continental, marginal-marine and marine origin, that dip northward from the Zuni Uplift and Chaco Slope into the interior of the San Juan Basin. (See Figure 2) Major Formations The major geologic formations to be penetrated range from mudstone and shales to siltstones and sandstones. The sandstones are highly productive aquifers which, under static conditions, would flow artesian. Water temperatures in the aquifers are high and therefore are a force to be dealt with. Temperatures range from 18ºC (65OF) in the upper aquifers to 48ºC (118º'F) in the lower. The mudstones are generally bentonitlc. (See Figure 2) GALLUP SANDSTONE: The Gallup Sandstone is the first major regressive wedge in the San Juan Basin of the Cretaceous era and at this project is about 35 m (115 ft) thick. It is medium grained and prior to depressurization carried a hydrostatic water pressure of over 72.5 kg per cm2 (1,031 psi) which 1s artesian. Compressive strength ranges from 334.7 kg per cm2 (4,760 psi) to 421.8 kg per cm2 (6,000 psi). Water temperature is approximately 30°C (86°F).

Jan 1, 1982

By Malcolm J. McPherson, Michael Hood

Sunnyside Mines, owned and operated by the Kaiser Steel Corporation, are situated near the city of Price, Utah. The complex comprises three adjacent mines, named simply Nos. 1, 2 and 3, all connected underground. Two seams, the upper and lower Sunnyside have been worked. These dip at about 10 percent to the north-east. The surface cover is variable due to the mountainous nature of the topography. The Sunnyside upper seam varies from 5 1/2 ft (1.7m) to 9 ft (2.7m) In thickness whilst the lower seam remains at about 6ft (1.8m). The separation between the two seams has ranged from 7 to 45 ft over the mined area (2 to 14m). Longwall mining has been practiced at Sunnyside for over 20 years due to difficulties of roof control encountered when using the roan and pillar system. Number 3 mine is bounded on the north and south sides by mines Number 1 and 2 respectively. Whilst current production is concentrated into Number 1 mine, much of the future of the complex lies in the further development of deeper reserves in Number 3 mine. Workings in this latter mine were curtailed in 1978 due to difficulties in ventilation. Present developments are ventilated partially from the neighboring Number 2 mine where no workings are in progress. The layout of Number 3 mine is illustrated on the schematic Figure 1. Trunk airways extend down dip from the surface at No. 2 Canyon and the Water Canyon for a distance of some 9,600 ft. (2930m). The area between the two sets of trunk airways has been worked extensively in both seams as have the corresponding reserves on either side in the connected adjacent mines. At the present time exhausting fans are sited at the top of a shallow shaft in No. 2 Canyon and an 8 ft (2.4m) diameter shaft sunk to a depth of 1013 ft (310m) closer to the current developments (Figure 1). The current airflow system, even with an additional 116,000 cfm (55m3/s) entering from No. 2 Mine, is adequate only for the development work now in progress but will be unable to support new longwall faces further downdip. The basic ventilation problem of this mine may be stated quite simply. In a situation where all intake and return airways pass through extensive old workings, a ventilation system design was required that would be effective, efficient and economic for the foreseeable future of the mine. ORGANIZATION OF THE PLANNING PROCEDURE The procedure followed during the study is illustrated on Figure 2. Initial ventilation surveys established the current state of the airflow system and provided the necessary data for setting up a Basic Network File in a computer store. The data in this file was a mathematical model of the ventilation system of the mine. The basic network was analysed by a ventilation network analysis program in order to correlate the measured and computed airflows and to establish the basic network as a true representation of the mine as it stood at the time of the surveys. The network model could then be extended to simulate the future development of the mine and alternative ventilation designs investigated. The remaining sections of the paper outline the work involved in each of these main phases of the planning procedure. VENTILATION SURVEYS Conduct of Surveys Two types of measurements were conducted simultaneously throughout the air-carrying routes of the mine: (i) Airflow measurements were made by anemometer traverse or smoke tube at 221 selected stations. Anemometer traverses were repeated at each station until at least three gave results to within 5 per cent. (ii) Pressure drop measurements were made across ventilation doors, regulators and, wherever possible, across stoppings. Additionally, frictional pressure drops were measured along airways where such pressure drops were significant (above 0.01 inches of water gauge or 2.5 Pa over a 100m distance). The trailing hose method was used to determine these frictional pressure drops. This involved laying out 100m of abrasive resistant plastic tubing (3 mm internal diameter) with a 4 ft. pitot-static tube facing into the airflow at either end and a low range pressure gauge connected into the line. The trailing hose method was preferred to the alternative barometer technique for this study because of (a) the relative ease of access between measuring points and (b) the greater accuracy within individual airways. The anemometers used were Davis Biram Type A/2-3" (30 to 5,000 ft/min) and Airflow Developments AM-5000 digital (50 to 5,000 ft/min). The pressure gauges employed were Dwyer magnehelic instruments. These were preferred to liquid in glass manometers because of their portability and dependability under adverse mining conditions. A checklist of the equipment used in the survey is given in Appendix 1. The instruments were calibrated before and after the surveys in the mine ventilation laboratory at the University of California, Berkeley. The survey occupied two teams, each of three men, for ten working days. The work consisted

Jan 1, 1982

By ERJIINICI FERRARIS

1. HISTORICAL REVIEW AND INTRODUCTION. THE development of the mining industry in Sardinia dates from the application of the minim law of 1859, which, following the example of the French mining law of 1810, declared prospecting to be free, and suppressed the liens which had previously attached the mine to surface ownership. The first ore-dressing plants were installed by German engineers upon the classic models of the Harz and of Freiberg; but in 1880 Sardinia commenced to open a new path in that industry, utilizing the refuse from the mining of rich, selected minerals, of poor deposits, and of mixed ores. The first experiments were attempts to adapt the existing apparatus to local conditions, but progress was rapid, as was demonstrated already in 1887 by the calamine-dressing-mill of Monteponi, which exhibited a large plant designed in accordance with the experience gained, and constructed entirely in the machine-shops of the country, after new models and designs.1 This example was followed two years later by the Société Malfidano, with a large plant of the same sort, and with the reconstruction of the old-fashioned-dressing-mill, built in 1880 by the Austro-Belgian Company. In 1900, almost all the mines of Sardinia had adopted the new designs, and the island contained 32 concentrating-works, employing 2,000 h.p. and 1,924 workmen. Since that time, there have been added a large dressing-mill for blende at Gennamari, and two for calamine, at San Giovanni and at Masua, while the establishments at other mines have been enlarged and perfected. For the treatment of intimately mixed ores, a large establishment has been built upon the new

Jan 5, 1908

By Arthur V. Corry

GOLD was discovered in Alder Gulch, Virginia. City, Mont., on May 26, 1863. In a short time some 6000 people flocked to the new discovery, and on the banks of Alder Gulch six settlements sprang into existence, the principal one, Virginia City, alone surviving. This town today has a population of 800, and is the county seat of Madison County. It is estimated that between forty and fifty million dollars in gold was produced up to 1904. Virginia City is situated at the mouth of Alder Creek where that stream leaves the narrow canyon that cuts the steep foothills flanking Old Baldy Mountain, elevation 9572 ft., 12 mi. south. Virginia City itself is 5700 ft. above sea level.

Jan 1, 1936

||Abad, Leopoldo F., Min Engr, Div of Mines, Bureau of Science Manila, P I '23 Abadilla, Quirico A, Geol, Lago Pet Corp Box 172, Maracaibo, Venezuela '20 ||Abbey, Robert Graham, The W W Sly Mfg Co Train Ave, Cleveland, Ohio '21 Abbott, A. N., Mines Supt, Mazapil Copper Co, Ltd Concepcion del Oro, Mexico '23 Abbott, Clarence E., Mgr, Mines & Quarries, Tenn Coal, Iron & R R Co, 1242 Brown Marx Bldg, Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr , Consolidation Coal Co , Elkhorn Div Jenkins, Ky. '16 Abbott, Robert R., Met Engr , Peerless Motor Car Co Cleveland, Ohio '12 ||Abbott, Wells Osborn, Ray Consolidated Copper Co Hayden, Ariz. '23 Abeel, George H, Jr., Cons Min Engr 4612 West 17th St , Los Angeles, Cal '18 Abel, Albert E., Asst to Pres, Valley Mould & Iron Corp Sharpsville, Pa. '19 Abernathy, George Elmer, Prof of Geol & Min , Kansas State Teachers College, Pittsburg, Kans. '20 Abey, Hiroshi, Min & Met Engr, Min & Met Dept, The Higher Technical School, Osaka, Japan. '17 ||d'Ablaing, Philip R, Chem , Anaconda Copper Min Co Great Falls, Mont '25 Aborn, Robert H , Research Assoc., Mass Inst of Tech Cambridge, Mass '19 Abouchar, Sylvain Sley, Min. Engi & Geol , care of S H Sekaly, 13 Rue El Nimr, Cairo, Egypt '17

Jan 1, 1923

By Walter Loel

THE application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and under varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarine geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions.

Jan 1, 1938

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

The National Mine Health and Safety Academy near Beckley, W. Va., is dedicated to reducing accidents and improving health conditions in the mining industry through education and training. Though this basic mission remains unchanged, the Academy now serves a much broader mining community than it did when established in the late 1960s. From its original emphasis on training federal coal, metal, and nonmetal mine safety inspectors, the Academy has expanded its programs to reach mining industry and labor representatives, state agency employees, and university students taking mining-related courses. The Academy's resident programs, short courses, seminars, and continuing education courses cover a wide range of subjects and various experience levels, but all have been developed with one idea in mind - to reduce accidents and health hazards through education and training of the widest possible audience.

Jan 11, 1979