Search Documents

By G. M. Schwartz, G. A. Thiel

Dimension stone was first quarried in Minnesota in 1820 and a very active industry has grown up over the years. The main basis of the present industry is a wide variety of igneous rocks sold under the general trade name of "granite." Also of considerable importance is the Ordovician dolomite sold under the locality names, Man kato, Kasota and Winona. THE first record of the quarrying of dimension stone in Minnesota dates back to 1820 when limestone was quarried locally for part of old Fort Snel-ling. Limestone quarries were operated at Stillwater, Mankato, and Winona as early as 1854. Granite was quarried first at St. Cloud in 1868, and within a few years thousands of tons were shipped to widespread points. Rough dimension stone for large buildings furnished the first important market, but beginning in 1886 paving blocks were in demand. The largest shipment was in 1888, when 1925 cars were shipped from the St. Cloud area. Quartzite was quarried first at New Ulm in 1859 and somewhat later at Pipe-stone and elsewhere in southwestern Minnesota. The productive dolomite quarries at Kasota were opened first in 1868 and have continued as large producers of a variety of stone to the present time. At present, the industry is controlled by relatively few operators, and for that reason detailed figures on dimension stone are not released for publication. A general idea may be obtained from the data in the Minerals Yearbook for 1948. The figures for total stone produced in Minnesota are 1,804,000 tons valued at $5,090,652. Probably the largest item in the latter figure is received from dimension stone. A better idea of the situation in relation to the country as a whole may be gained by using the data for 1930 when more companies were operating in Minnesota, and complete figures were published. In that year Minnesota produced granite valued at $2,668,119 and ranked third among the states in value. Minnesota's production of granite was almost exclusively for dimension stone. In the same year Minnesota produced 300,000 tons of limestone (dolomite) valued at $840,860, and this likewise was mainly dimension stone. In finished limestone Minnesota ranked second among the states in 1930. Sandstone and minor amounts of quartzite are the only other dimension stones that have been produced in Minnesota, but the quarries are now inactive. The commercial stones of Minnesota have been described in two reports by Bowlesl and by Thiel and Dutton. The early history of quarrying in Minnesota and extensive notes on the various rocks are given by N. H. Winchell.8 Small limestone and dolomite quarries were numerous throughout the area of Paleozoic rocks in southeastern Minnesota. Early production was largely dimension stone. With the increased use of Portland cement, most of these ceased production, and today only those at Kasota and Winona remain in operation. In recent years many quarries have reopened and new ones started, but these are devoted to the production of crushed rock and agricultural lime. As the application of modern quarrying and finishing methods increased, small companies in the granite business have dropped out, and the remaining companies have modernized their plants, purchased old quarries, and opened up new ones, thus furnishing a wide variety of granites suitable for most of the customary uses. It is the purpose of this review to present notes on the geology and operations of each of the quarries now operating within the state. Granites and Related Igneous Rocks The term granite as used in this report includes granites, gneisses, diorites, gabbros, and other igneous rocks. The granites of greatest economic importance are found in three widely separated regions, see Fig. 1. 1—Central Minnesota in the region of the city of St. Cloud, 2—the upper Minnesota River valley region, 3—the northeastern portion of the state, commonly referred to as the Arrowhead region. The St. Cloud Region: The rocks of the St. Cloud region are mainly granites and related rock types such as monzonites and quartz diorites. The stones may be grouped into three major types, namely, pink granite, red granite and gray granite. Most of the pink granite occurs in the area to the southwest of St. Cloud. The rock is best described as stone with large pink crystals set in a finer grained black and white background. The minerals of the matrix occur in remarkably uniform sizes, and the pink crystals are sufficiently uniform in their dis-

Jan 1, 1953

By C. H. Samans, G. F. Tisinai

HARDENING and embrittlement of the ferritic chromium stainless steels at temperatures near 885 °F have been known for a long time.' However, no satisfactory explanation has been given. Both ordering and precipitation hardening have been suggested. Fisher, Dulis, and Carroll2 discovered a chromium-rich body-centered-cubic precipitate in embrittled alloys. Subsequently, Williams' and Wright4 also have found evidence of this body-centered-cubic constituent. William's hardness, electrical resistance, and magnetic studies led to his proposal of a new constitutional diagram for the Fe-Cr alloys. The new feature of this diagram is the eutec-toidal decomposition, below about 970°F, of the s phase into two stable body-centered-cubic solid solutions, one rich in iron and the other rich in chromium. An observation of Heger5 that the amount of s phase has increased and the amount of chromium-rich body-centered-cubic phase decreased in the interval 5000 to 32,600 hr at 900°F, even though the alloy increased in hardness, casts some doubt on this diagram. If precipitation hardening causes the embrittlement, the precipitate probably is always coherent with the matrix, since no evidence of overaging has been reported. It cannot be stated positively, however, that Fisher's body-centered-cubic constituent is the embrittling phase. According to Preston's data,6 such a chromium-rich phase should have a parameter less than about 0.5 pct larger than that of the iron-rich matrix lattice. Moreover, the constitutional relationships whereby Fisher's constituent forms, and whether it is stable, metastable, or a transition phase, are not yet completely clear. The recent studies of Wright4 and of Lommel,7 as well as the earlier studies of Becket8 and of Hochmann,9 have shown that 885°F hardening occurs in relatively pure Fe-Cr alloys. No evidence of its occurrence or absence in chromium itself has been reported. The rate of hardening in high purity alloys seems appreciably slower than that in alloys containing larger amounts of impurities (chiefly carbon and nitrogen). This may be due merely to the absence of hardening and straining effects from precipitated carbides and/or nitrides. These observations on high purity alloys make it seem unlikely that 885 °F hardening is caused by a constituent containing other than iron and chromium atoms, e.g., carbides and/or nitrides. Wright,4 Lommel,7 and Lena and Hawkes10 emonstrated the accelerating effects of a finely dispersed precipitate of (probably) chromium nitride on the hardening reaction. This appears to be evidence that lattice straining increases the rate of nucleation of the hardening constituent. Some new observations on 885°F hardening are reported here. They show an effect of preheat treatment that should contribute to a better understanding of the 885°F hardening phenomenon. They also clarify a discrepancy which exists in the literature. Some investigators have reported most rapid hardening at 885", whereas others have reported it at 930°F. The present work also shows that 885°F hardening does not occur in electrolytic chromium, and that any long range ordering type of reaction affecting any sizeable part of the volume is unlikely. Materials Studied Table I shows the currlposition of the alloys used in this investigation. In these alloys carbon and nitrogen are present in roughly similar amounts. Presumably both elements precipitate, as carbides and/or nitrides, during the heat treatments given.

Jan 1, 1958

By F. Kurata, P. C. Davis, T. L. Gore

An experimental method and apparatus for the study of the low-temperature phase and volumetric behavior of volatile mixtures are described. The phase diagrams, including the critical points, and the volumetric behavior of a natural gas and a mixture of the natural gas with methane at temperatures from -40°F to -200°F and pressures to 1.200 11si are givrn. INTRODUCTION Knowledge of the phase and volumetric behavior of mixtures of the light hydrocarbons at low temperatures is becoming increasingly important as interest in low-temperature separation processes increases. Distillation at low-lemperatures has been used for some time to recover ethane and ethylene from natural gas and refinery gas for petrochemical uses. Removal of excess nitrogen from natural gas by distillation has been proposed as a means of increasing the capacity of gas transmission lines and of improving the marketability of the gas.1,2 Evaluation of the latter process has been hampered, however, by the scarcity of data from which the phase behavior of natural gases at low temperatures might be predicted. While existing correlations of vaporization equilibrium constants may be used to predict the behavior of such mixtures at lower pressures, high-pressure computations often require knowledge of the location of the critical point of the system involved. Although correlations have been developed for the prediction of the critical temperature and pressure of certain types of hydrocar-bon systems, they do not apply to very volatile systems such as nitrogen-bear-ing natural gases. This paper describes the initial stages of an investigation of the low-temperature behavior of a numher of natural gases and other gases of commercial interest. The experimental method and apparatus are described. and the phase and volumetric behavior of a natural gas and a mixture of the natural gas with methane are presented. PREVIOUS WORK The published low-temperature vapor-liquid equilibrium data for hydrocarbons and mixtures of hydrocarbons with nitrogen and helium are listed in Table I. Most of these data are for binary systems, and the data of Stutz-man and Brown" at 100 psi are the only data on a natural gas. The data of Bloomer and Parent3 on the methafie-nitrogen system, which have been phblished since this study was completed, are a valuable addition to the knowledge in this field. Prior to the publication of these data the only published critical point data on systems having critical temperatures below the ice point were those of Ruhemann.1 on the methane-

Jan 1, 1952

The Committee appointed by your Board of Directors to nominate Officers for the Institute for the year 1915 invites the participation of all members in the nominations. The suggestion of names for the various offices will be appreciated and given full consideration when making the selection of candidates which this Committee will recommend. The officers to be elected at the annual meeting in February, 1915, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows:

Jan 6, 1914

By B. K. Asdell

Crude kaolin exhibits a wide particle size range in which kaolinite is the predominant mineral. Bene-ficiation by wet processing produces high-brightness white pigments. The wet processing techniques peculiar to kaolin beneficiation are emphasized in this article in some detail. Included are discussions of long-distance pipeline transportation, centrifuga-tion, flotation, spray drying and shipment as 70% solids slurry. Georgia, a state seldom considered to be an important mineral producer, has one surprising feature — it is the nation's largest producer of kaolin. Kaolin is a highly important raw material in the paper, rubber, ceramic whiteware, paint and chemical industries. In 1965, more than 2.7 million tons of kaolin were produced in this state, a 150,000-ton increase over the preceding year, and production continues to climb. Strictly defined, the term "kaolin" applies to a group of hydrous aluminum silicates in which kaolinite is the predominant mineral. Kaolinite is inherently white, non-abrasive, chemically inert, and of a very fine particle size, ranging from sub-micron to 40-microns equivalent spherical diameter. An electron-micrograph of kaolinite is shown in Fig. 1. The particles finer than about 2 microns are thin, elongated plates, hexagonal in outline. The larger particles, coarser than 2 microns, are predominantly vermicular in outline with a foliated structure. Table I shows a typical chemical analysis of commercial, wet-processed kaolin compared to pure kaolinite. The sedimentary Cretaceous deposits of the Coastal Plain are the source of most of the kaolin produced in the Southeast. These deposits are of relatively high purity, and it is not uncommon to find the clays running greater than 90% kaolinite. Beneficiating plants using wet processing techniques are most numerous in an area within about 50 miles east of Macon, Ga., in a band approximately 15 miles wide. Kaolin may vary widely in quality from one deposit to another, or within the same deposit. The qualities critically examined are brightness index as measured by reflectance, viscosity of water suspensions, bleachability and particle size distribution. Crude kaolin always contains sand and mica in varying amounts, along with small amounts of many other minerals. These are classed collectively as "grit" because; they are generally coarser than 325

Jan 1, 1968

By H. Evans, L. A. Hunt

The raw materials used in the blast furnaces at the Geneva Works of U.S. Steel Corp. have a high degree of variability in size-consist and chemical content. To overcome the problems caused by the use of highly variable raw materials in the blast-furnace operation, large blending piles are used. An investigation of the blending system showed that variability was significantly reduced by the use of these blending piles. This paper describes the blending system, the method used to evaluate the effect of the blending system, and the results of the investigation. The remarkable improvement in blast-furnace performance since World War II has been in large measure due to the use of beneficiated burdens to reduce the variation of both chemical analysis and size consist. This practice allows the operator better control of his blast furnace, enabling him to operate more economically and to produce chemically uniform hot metal. Planning for uniformity usually begins during mining by extracting ore from several locations within a pit to produce a final product with a specified analysis. Another approach is to stockpile ores having widely varying analyses in individual piles and then drawing the required amounts from each stockpile to provide a blend with a predetermined analysis. A further improvement in blending procedures is to take ores from several sources, bedding them horizontally in layers and reclaiming by vertical slicing from the blended pile. The last procedure, when properly executed, is one of the best methods for achieving maximum uniformity with highly variable ores. U.S. Steel Corp.'s Geneva Works initially obtained iron ore for their blast furnaces from the Cedar City area of southern Utah. These ores were formed primarily by the replacement of limestone and siltstone formations with solutions containing iron and several other elements. The original iron content of the ores in the ground varied from a high of 70% to practically zero with a minimum acceptable iron content for shipping of 37%. Substantial amounts of silica, calcium, magnesium and alumina were found in the ores along with minor amounts of copper, lead, zinc, nickel, titanium, manganese, phosphorus and sulfur which were sometimes present in detrimental amounts. Iron-to-silica ratios varied considerably throughout

Jan 1, 1968

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

In the search for practical geological problems amenable to solution by the potential methods, the geophysicist is led to study mathematically various theoretical cases. In these idealistic discussions, the media under consideration are generally supposed to be homogeneous and iso-tropic. The geophysicist, of course, realizes perfectly that these conditions do not occur in their entirety in reality. However, the assumptions made are justified, because very often they are necessary in order to render possible an exhaustive study of a given problem, which otherwise would be too complicated, and would not lend itself to a complete mathematical analysis. Of the above two assumptions, that concerning the homogeneity of a given geological formation is satisfactorily realized except in so far as isotropy is concerned, since this property is not often encountered in practice. As a consequence, it is very desirable for the geophysicist to have quite an extensive knowledge of the properties of anisotropic formations, and of the laws that govern the propagation of electric current therein. With such principles in mind, he will be able to decide whether the conclusions arrived at in simple, isotropic conditions are still correct in more complex cases, or in what way they must be modified or adapted in order to constitute a sound basis for the interpretation of the results obtained in anisotropic media. On the other hand, the fact that in anisotropic formations the mobility of the ions is greater along the strike than perpendicular thereto can be utilized for determining the direction of the dip by induction measurements. We therefore propose to study in three successive chapters the following points: 1. Propagation of the electric current in anisotropic media. 2. Some consequences of the anisotropy of geological formations with reference to the surface electrical measurements, and their interpretation. 3. Determination of the direction of the dip of anisotropic formations by surface induction measurements.

Jan 1, 1934

By Robert B. Fulton

Commercially, celestite (SrSO4) is the predominant strontium mineral. Among other strontium-bearing minerals, only strontianite (SrCO3) occurs commonly; however, it is rarely an item of commerce. Production of celestite is principally in Mexico, Spain, and Turkey. An attempt to produce celestite in Canada was unsuccessful. The United States, which is wholly dependent on imports, chiefly from Mexico (99%), is the largest consumer of strontium. Lesser quantities are consumed in Japan and Europe. The Federal Republic of Germany is the principal source of strontium compounds imported to the US. Uses The principal uses of strontium are for the manufacture of strontium carbonate and nitrate. Carbonate is used in glass for TV tube face plates and in ceramic ferrites for magnets. Nitrate is used in pyrotechnics, mainly in safety flares, to which it imparts a characteristic brilliant red color. Minor amounts of strontium compounds are used in electrolytic zinc manufacturing where the carbonate is used to remove unwanted lead. Small quantities are consumed in greases, ceramics, soaps, alloys, and pharmaceuticals. Specifications Typical celestite specifications for the carbonate and nitrate markets are shown in Table 1. Specifications of manufactured carbonate, sold in two grades, one to the glass industry and the other for ceramic ferrites, are shown in Table 2. Both grades of carbonate are shipped in palletized 50-lb bags. Glass grade material is shipped in bulk by rail. [ ] Manufacturing Processes The following description is adapted from Anon. (1980) . The manufacturing process for strontium carbonate and strontium nitrate chemicals is conceptually simple. Strontium nitrate is made from strontium carbonate in two additional steps. The production process begins with celestite, the natural form of strontium sulfate. In the first step the ore is crushed, ground, and mixed with coke. This mixture is then fed into a kiln where the ore is reduced at high temperatures to strontium sulfide; the coke is added to the ore as a source of energy and carbon. The carbon combines with the oxygen [ ]

Jan 1, 1983

By F. I. Stalkup

Vapor-liquid phase equilibrium experiments have been conducted in a static equilibrium cell on mixtures of a light, 45 API stock- tank gravity reservoir fluid and a rich hydrocarbon gas containing approximately 55 mole per cent of intermediate hydrocarbons. Both apressure-vs-composition study of the gas and a simulated reservoir fluid, and a multiple-batch contact simulation of the condensing-gas-drive oil recovery process were performed. In the latter experiments equilibrium gas and liquid compositions were analyzed. Also, conventional, "condensing-gas-drive", long-tube displacement experiments of the reservoir fluid and gases of various richness were performed. The results of these experiments could not be satisfactorily interpreted by the conventional pseudo-ternary-diagram representation of multicom-ponent phase behavior. The results seem to be explained better by considering a bubble-point surface and a dew - point surface joined in a plait-point locus. Portions of the plait-point locus cannot be "seen" directly by the rich hydrocarbon gas because of curvature of the dew-point surface. In such a system, continuous injection of the rich gas over stationary reservoir fluid might form a zone of contiguously miscible compositions from pure rich gas to pure reservoir fluid by: (1) saturating the reservoir fluid with injected gas to the bubble-point surface; (2) creating by mass transfer with fresh injected gas a path of contiguously miscible compositions along the bubble - point surface to the plait-point locus; and (3) creating by mass transfer with additional injected gas a path of gas compositions along the dew-point surface up to the point where direct miscibility results between dew-point fluid and the injected rich gas. INTRODUCTION The use of the pseudo-ternary-phase diagram to illustrate miscible displacement phase behavior has been discussed by several authors.5,7 Such a representation of phase behavior is not rigorous, but the ternary diagram nevertheless gives a qualitative picture of what actually occurs in a miscible displacement process. Fig. 1 is a typical illustration of miscible displacement phase behavior by a ternary diagram. The multicomponent hydrocarbon system is divided into three pseudo-components: a light fraction containing methane and nitrogen, an intermediate fraction containing ethane through hexanes plus carbon dioxide, and a heavy fraction containing heptane and heavier components. A two-phase region is bounded by a dew-point curve and a bubble-point curve, which are joined at the critical point. The concept deduced from such a representation for miscible displacement by a condensing-gas-drive process is as follows: a rich gas G, which lies to the right of the limiting tie line through the critical point C, is injected into the reservoir and contacts reservoir fluid L, saturating the reservoir fluid to give bubble-point fluid L1 and equilibrium dew-point gas GI. Continued injection of rich gas changes the composition of the saturated liquid L1 through a series of liquid compositions lying along the bubble-point curve, until the critical composition C is reached, at which point direct miscibility with the rich gas is achieved. Some equilibrium gas with compositions lying along the dew-point curve from G1 to C is also formed in this process. Thus, continuous injection of rich gas forms a

Jan 1, 1966

By G. Hileman

At present there are three fields in commercial exploitation in the Argentine. In order of production they are: (1) Comodoro Rivadavia, (2) Salta, (3) Plaza Huincul. Comodoro Rivadavia.—This field is on the coast of the Territory of Chubut in the southern part of the republic. It is being developed and exploited by Yacimientos Petroliferos Fiscales, the government oil entity, and five private companies. The immediate coastal portion of the field, which embraces the original discovery area, is almost completely developed. This is especially true of the original government reserve and one private property. The Y.P.F. has extended its explorations and developments westward to Escalante, 27 km. distant on the state railway. This extension has been the most active and prolific section of the field for the past three years. The government has also continued its exploration drilling in the region lying south of Colonia Sarmiento and east of the Rio Senguer. Private companies have not been able to extend their operations beyond the claims they had in process of acquisition in 1924, when the government reserve areas were established. The Y.P.F. is the major producer of the field and employs modern methods and appliances. Practically all its drilling and pumping operations are electrically operated, from a central power plant. In view of t'he scarcity of water supplies, this facilitates operations and is an economic factor of considerable importance.

Jan 1, 1934

By Fred Jones

The Cripple Creek district is in Teller County, Colo., about 18 miles in an air line west of Colorado Springs and at an elevation of 10,000 It. A line drawn through Colorado Springs and Pikes Peak will, if continued, about pass through the district. The character of the country generally is rolling, with few trees and little snow fall. The annual precipitation is about 20 in. All the water used by the mines is supplied by the Altman Water Co., which pumps from the west slope of Pikes Peak. Gold was discovered in 1891, since which time the district has produced $411,000,000. The peak of production was reached in 1900 and amounted to $25,000,000. At present the production amounts to about $400,000 per month. Geology In general, the geology of the district is simple; ash veins and dikes traverse a volcanic plug of breccia. The ore occurs as enriched spots along these dikes and veins. The dikes represent the most recent extrusions and consist of basalt and phonolite. (For a complete geological description reference is made to Professional Paper 54, 1906, of the U. S. Geological Survey.) The ore consists of small parallel seams of high grade. In only a few cases is the gold disseminated through the rock; much of the gold in the broken ore is found in the fines. The wall rock is hard blocky granite or breccia. About 25 per cent. of the rock mined is shipped as ore to the Golden Cycle mill at Colorado Springs. The height of an ore deposit is usually several times its length. Few flat oreshoots have been found. The veins are all steep and have a dip of 70 to 80°. Development The claims are all 300 by 1500 ft. and are held by location or patent. All mining is done through shafts, one of which has reached a depth of 2600 ft. The main working shafts are 41/29 by 1335 It. and are made up of three compartments, each 4 by 41/2 ft. in the clear. They are timbered with 10-in. Oregon posts and plates and 8-in. spreaders. Two compart-

Jan 1, 1925

By M. W. Lightner

IN 1947 the steel industry rebounded from its wartime effort and produced a record-breaking peacetime tonnage of steel ingots. During the first six months of the year the industry produced 42,000,000 tons of ingots and expected to produce 85,000,000 tons for the year. With a rated capacity of some 91,000,000 tons, production was at a rate of about 93 per cent of capacity. Credit must be extended to the steel producers who have maintained this steady state of operations while faced with many problems, not the least of which was a continued shortage of satisfactory scrap. Furthermore, the steel industry started a record-breaking peacetime expansion program at a total cost of more than $1,000,000,000. This program will increase the ingot-making capacity of the country by 2,500,000 tons and should be completed in 1948.

Jan 1, 1948

By W. A. Clark

The production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl. of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. Reasons fob Gravel Packing Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b) allowing deep submergence of the pump into the oil zone. In a conventional well—that is, where the liner is set in an open hole-. even though perforation sizes are chosen according to known rules based on analysis of sand grains from samples from the zone, there is likely to be some production of sand. This may be due to the miscalculation of

Jan 1, 1940

By W. A. Clark

The production of sand in an oil well increases operating costs because of abnormal wear in subsurface equipment, the necessity for frequent cleanouts, and the need for a means of disposing of the sand. Moreover, removal of sand from the zone can bring about the creation of cavities from which bodies of formation, sand or shale, may slough into the hole, endangering the shutoff, impeding production or collapsing the liner. The procedure known as gravel packing is attracting attention as a means of controlling these factors and contributing to the productive life of a well. That gravel packing is now substantially beyond the preliminary stage on the Pacific Coast is reflected in the 191,000 bbl. of oil produced monthly by the 66 gravel-packed wells in 11 different producing sectors. Reasons fob Gravel Packing Gravel packing, if properly carried out, can be expected to provide the following benefits: 1. Prevent the movement of sand and thus eliminate sand production and sand fills, and prevent the formation of cavities. 2. Provide a practical, relatively inexpensive, large-diameter hole, which will provide well-known theoretical advantages. 3. Support the walls of the hole by completely filling the space between the liner and the formation, regardless of its irregularities, and afford a support for liners. 4. Provide for more efficient pumping operations in wells by: (a) possibly utilizing the gravel as a gas trap in pumping gaseous fluids, (b) allowing deep submergence of the pump into the oil zone. In a conventional well—that is, where the liner is set in an open hole-. even though perforation sizes are chosen according to known rules based on analysis of sand grains from samples from the zone, there is likely to be some production of sand. This may be due to the miscalculation of

Jan 1, 1940

By George Schore

Radiation grafting of ion exchange structures contains ion exchange groups but may consist of neutral groups. High energy grafting of monomers on to polymers has-been known since 1950 (1.2); manufacture on an industrial level was-begun in 1970.(3) Proper choice of substrate and monomer will produce various ion exchange membranes with differing physico and chemical properties. Grafting a selected monomer to the proper polymer will provide selective ion exchange with assured chemical protection of the substrate. Ion exchange systems utilizing radiation grafted structures to polymers have been fabricated to "capture" gold from drag-out and rinse water and silver from cyanide rinse water. Other ion exchange systems can feasibly be produced to remove other precious metals. Rotating Cathode Technology is used to recover the metals from their concentrated eluating solutions as pure metal foil.

Jan 1, 1984

By Howard S. Strouth

Investors and mining companies in the U. S. have recently shown increased interest in the Union of South Africa. This has been sparked partially by the founding in the U. S. of a large investment trust which will hold substantial shares in many of the leading gold and uranium producers. The average U. S, mining man's judgment of the Union, however, may be somewhat clouded by recent headline news. We are inclined to take a strong dislike to the stern measures of the present Union government with regard to its native majority. Others possibly think of South Africa in krms of a British colony which, under pressure of rising African nationalism, must eventually be abandoned. These concepts frequently suffer for lack of precise information.

Jan 5, 1959

The co-operation of the members of the Institute is earnestly sought by the Committee on Nominations, recently appointed by the Board of Directors, in its work of formulating a ticket for officers and places falling vacant in the Board of Directors in February, 1916. The Committee must present the official ticket of nominations to the Board of Directors at its October meeting. Members are, therefore, urged to send promptly their nominations for officers and Directors in order that the Committee may have an opportunity to give there full consideration. The officers to be elected at the annual meeting in February, 1916, are: One officer, known as Director and President. Two officers, known as Director and Vice-President. Five officers, known as Director. The attention of members is called to Articles V and VII of the Constitution, and to By-Law XIII, which reads as follows: -

Jan 6, 1915

By Reinhardt Schuhmann JR

Metallurgical Engineering Volume I, by Reinhardt Schuhmann, Jr. Addison-Wesley Press. $7.50, 390 pp., 1952. -This first volume, engineering principles, of a two volume work, is intended by the author to meet a need for reorganization of instruction in extractive metallurgy. Its three main objectives are to organize the subject matter according to basic principles and unit processes; to integrate the underlying science of physical chemistry with metallurgical engineering; and to put greater emphasis on analysis and quantitative solution of engineering problems. Vol. I deals with unit processes, stoichiometry, thermodynamics, fuels, fluid flow, heat transfer, pyrometallurgical systems and refractories. Vol. II will take up the individual unit processes. Initiation and Growth of Explosion in Liquids and Solids, by F. P. Bowden and A. D. Yoffe. Cambridge University Press. $4.50, 104 pp., 1952.-The book is a study of decomposition by impact and by friction of explosive substances and deals mainly with the work of the authors and their collaborators. Research is still in progress but results thus far indicate that the mechanism of initiation is relatively simple. Findings are thoroughly discussed, and the latter part of the monograph describes the way in which a small nucleus of decomposition can grow into a large scale explosion.

Jan 1, 1952

By Gordon H. Geiger, John M. Svoboda

One mechanism of metal penetration into mold aggregates by cast steels is vapor state mass transport. In order to further understand and quantify this mechanism, the steady-state diffusion of metallic vapors was studied at 1250" to 1600°C in controlled oxygen pressure atmospheres by measuring the weight loss from a metal bath whose vapors were allowed to diffuse through a porous aggregate compact held at constant temperature. Mass transport rates substantially greater than those predicted from the assumption that the vaporizing species was the elemental metal vapor were observed. Vaporization rates were found to increase with an increase in the oxygen partial pressure in the gas atmosphere with maximum vaporization occurring at oxygen partial pressures just below those in equilibrium with a liquid oxide layer at the given temperature. When the liquid oxide layer was present, no vaporization was observed. Metal carbonyls were ruled out as the vapor species involved because of their thermodynamic properties. The species with the enhanced volatility were deduced to be gaseous metal-oxygen molecules, probably the polynuclear oxides (FeO)2 and (Mn0)2. Diffusion followed the ordinary diffusion mode, and Knudsen diffusion is not important in normal foundry molds. The interdiffusivities of the metallic vapors and the mold atmosphere, through the porous aggregates, were measured. The effective interdif-fusivity of the vapor species and mold atmosphere through the aggregate may be expressed as follows: Deff,12 - — where E is the void fraction of the aggregate and 7 is the "tortuosity factor". Aggregate material had no effect on diffusion rates, and the only relevant parameter was the void fraction. Values for 7 ranged from 3 to 6 for normal foundry aggregates with 4 being considered a good representative value. An area of interest in high-temperature metallurgical processes which has received little attention in the past is the diffusion of metal vapor species in porous aggregates. Research into the metal penetration phenomenon' in foundry molds has shown that a major penetration mechanism is the vapor transport of metallic species into the porous foundry sand molds, followed by condensation of metallic films on the sand grains. Considerable study of the vaporization of metallic species has been reported in the literature, and the vapor transport properties of many metallic species have been determined.2'3 Many instances have been observed where the vaporization behavior could only be explained by the existence of a metallic species with a vapor pressure greater than the elemental metallic species. These species were identified or, in some cases, presumed to be carbonyls,4,5 hydroxides,6-9 or vaporous oxides.10-16 The diffusion of gases through porous aggregates has received considerable attention in the literature pertaining to catalysis, although primarily at low temperature, and more recently in the literature concerned with ore reduction.17-22 The following experiments were devised and carried out in order to determine the nature of the metallic species involved in the metal penetration phenomenon, and the effective diffusivities involved. EXPERIMENTAL APPROACH Steady-state diffusion was selected for experimental convenience. The experimental systems used, shown in Figs. 1 and 2, consisted of a porous aggregate specimen contained in an impermeable alumina tube held above, and just separate from a metal bath. The entire system was held at constant temperature and pressure in a furnace with a controlled oxygen partial pressure atmosphere. After a brief period of nonsteady state behavior, a steady flux of metal vapor through the porous aggregate will develop due to the concentration gradient of metallic vapor in the gas phase. The flux of metallic vapor from pressure may be neglected because there is no pressure gradient. There is no flux from convection because there is no net flow of gas within the metal-aggregate system, and thermal diffusion is negligible compared to the flux from ordinary diffusion. If the material being studied is allowed to vaporize until steady-state behavior is attained, the experimental results may be analyzed using Fick's First Law.

Jan 1, 1970

By Donald Barton

THE purpose of this torsion balance survey and the quantitative calculations was to delimit the extension of the cap rock at the Hoskins Mound salt dome. The sulfur ore in the Gulf Coast sulfur-bearing salt domes occurs in the lime rock, which is the outer layer of the cap-rock mass, and also in the underlying gypsum zone. The status of the exploration and exploitation of the Hoskins Mound dome at the date of this survey is shown by Fig. 1. The mound had been covered by the very early prospect wells of the Mound Oil Co., and the later and more numerous prospect wells of The Texas Company. The Freeport Sulphur Co. was producing from the flank wells in the southwest quadrant. The limits of the cap were surmised to lie inside the centers of quad-rangles 4F, 3F, the center of the NE. ¼ of 2E, and the north line of 2D. That surmise was based partly on the data of Fig. 1 and partly on the position of the edge of the topographic mound. The management of the Freeport Sulphur Co. wished to block out the extent of its ore reserves with a minimum of expenditure. The management was informed by the writer that no geophysical method could map the presence or quantity of sulfur directly, or determine the presence and quantity of the lime-rock cap independently of the rest of the cap, but that a reasonable probability existed that the approximate position of the edge, the depth and the thickness of the cap-rock mass as a whole could be determined through quantitative calculations based on the data of a very careful torsion balance survey. Considerable lime rock would probably be present, of course, wherever much cap rock was present. This paper presents the data of the survey, our calculated prediction of the configuration of the cap rock, and the degree of confirmation by the subsequent drilling. The survey was made by the Geophysical Research Corporation, under the direction of the writer. The work of the calculations was done by Andrew Gilmour, then assistant to the writer.

Jan 1, 1936