Search Documents

Enhancement of Energy Efficiency in Fine Grinding of Copper Sulfide Minerals Using a Pilot-Scale Stirred Media Mill - IsaMill The mineral liberation size of run of mine ores has dramatically reduced over recent years. As a result, the demand for fine grinding which is the most energy-intensive form of grinding has markedly increased in the minerals industry. Furthermore, the fine grinding costs increase exponentially with decreasing product particle size. As a result of the increased energy requirement for fine grinding, it is desirable to optimise fine grinding processes such as stirred media milling (ie IsaMill) to enhance energy efficiency, throughput and the product fineness. In the present study, the influence of slurry rheology, grinding media type and grinding media-to-feed size ratio on energy efficiency in a pilot-scale IsaMill was investigated under certain industrially relevant pulp processing conditions. It was shown that a critical rheological state existed, below which the energy required to achieve an 80 per cent passing (ie P80) 20 ¦m product size was unaffected by shear rheology (ie apparent viscosity and shear yield stress) whilst above which the grinding energy required increased dramatically with increasing shear rheology. Colorado River sand (3.35 mm) showed higher energy efficiency than MT1 ceramic media (2.5 mm) for a target P80 of 20 ¦m in the solids concentration range of 38 to 55 per cent by weight, but the former experienced more than four times the wear rate of the later. The high wear rate of the Colorado River sand may be due to its much lower hardness. For feeds with an 80 per cent passing (ie F80) 70 to 110 ¦m, 2.0 or 2.5 mm MT1 media appeared to be more energy efficient than 3.5 mm MT1 media whilst a media-to-feed size ratio of 41 to 53 is applicable for ~50 ¦m (ie F80) feeds for efficient grinding.

Sep 13, 2010

To ensure that its voice is heard in the development of policies and plans under the Resource Management Act, the mining industry is challenged to participate in their preparation. This paper outlines a number of practical ways in which the industry can participate in debate on sustainable management and how it can be put into practice within the industry.

Jan 1, 1992

By A M. Sherwood

The Otago and Southland lignite deposits represent by far the largest known fossil energy resources in New Zealand. Despite their size they have remained virtually untouched since exploration in the 1970s and 1980s defined their extent. In total there is an estimated 10.9 billion tonnes of lignite in 13 defined fields in Otago and Southland. Much of the exploration work only targeted seams at shallow depth and it is highly probable that there are further resources at depth in the fields that have been explored to date.   L&M Lignite Limited (L&M) holds exploration permits over a number of lignite deposits and is currently engaged in pre-feasibility studies to investigate the potential of the lignites for gasification. L&M is focussing its studies on the Hawkdun and Ashers-Waituna deposits. Coal quality in these deposits, particularly Ashers-Waituna, is highly suitable for gasification. In total the two deposits contain 1647 Mt of potentially recoverable lignite. L&M has engaged a variety of consultants to progress this project. The Hawkdun and Ashers-Waituna deposit databases have been re-evaluated and the resources remodelled. Further drilling has been carried out and the coal quality database has been expanded. The baseline project is to develop a mine to feed a plant that will produce liquids, specifically low-sulphur diesel and naptha, using the Fischer-Tropsch process. The project anticipates a staged development of 10 000 barrel per day units, each requiring mining at the rate of 12 700 tonnes of lignite per day. The production of other products including ammonia-urea, methanol, hydrogen and electric power is also under study.

Jan 1, 2005

By C Garlick, O Gregory, H Rogers, B I. Winters, Z C. Ye

BHP New Zealand Steel produces iron from titaniferous ironsand by a direct reduction process comprising multihearth furnaces/rotary kilns/electric iron melters. The electric iron melter is a six-in-line rectangular submerged-arc furnace which takes the partially reduced ironsand (80 per cent metallisation) from the rotary kiln and completes the reduction process to produce iron of nominally three per cent carbon. As the melter operates at around 1500¦C and under very hostile conditions, it is near-impossible to obtain any basic operating parameters such as the velocity and temperature distribution in the slag and in the molten iron. As a first attempt to understand the operating conditions inside the melter, a scaled room-temperature model using wax and water to represent the slag and iron, was constructed. This paper will report on some of the preliminary model results on the temperature distribution.

Jan 1, 1995

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

Slime Flotation Using Ethoxylated Surfactants in Solutions of the Electrolytes

Sep 13, 2010

Importance of Strain to Fragment Strength in Blasting Induced Pre-Conditioning When a rock is blasted, cracks propagate through the rock causing the rock to fracture. This paper focuses on applying the results from a series of small scale blasting tests were designed to show the effect that varying blast variables such as explosive type and explosive energy have on the resulting strength of the post blast fragments. It was shown that the velocity of detonation of the explosive product affects the reduction of fragment strength. This has important implications for the downstream comminution process. The observations from these tests are then explained with reference to the principles of fracture mechanics. A simple but effective prediction of blast induced preconditioning is shown.

Sep 13, 2010

Some Otago quartz veins display spectacular open-space filling textures indicative of shallow formation. Fluid inclusions in some such veins show that fluid immiscibility occured before or during mineral deposition. This immiscibility or 'boiling' occured at depths ranging from about 3 km to within as little as about 100 metres of the paleo-surface. Temperatures of mineralization range from 190 - 250¦C. Metals deposited in these veins include: Au(+Ag), Hg, Sb and As. Hydrothermal alteration is confined to minor silicifation of immediate wall-rock schist, less than about two metres from the veins. These veins have some similarities to classical epithermal systems elsewhere in the world, although wall-rock alteration is much less developed in Otago. From analogy to these classical epithermal systems, it is speculated that gold mineralisation may be found beneath Otago stibnite and cinnabar localities.

Jan 1, 1987

The dissolution of the naturally occurring mineral zircon (ZrSiO4) is examined after ball milling it with magnesium oxide for up to 100 hours in a laboratory mill. There was little effect on the solubility for the initial two hours where size reduction of the zircon was considered to be the dominant effect. Beyond two hours the dissolution increased as a function of the square root of milling time. X-ray diffraction of the powders did not reveal the identity of the soluble phase. However, a nanocrystalline phase was present after milling and this is thought to be the soluble phase.

Jan 1, 2000

By V Barrera, A Brzovic, M Gaete, L Burgos, E Arancibia

Fragmentation is one of the most relevant parameters in the design and operation of a mine using the caving mining method. Fragmentation affects all subsequent operations, including extraction, comminution processes, secondary blasting and transportation.There are a number of different models in the literature to estimate the size of the ore fragments that report to the drawpoints; however, there is still no industry consensus about which one to use. This paper proposes a new model for predicting the fragmentation reporting to the drawpoints that is based on the geotechnical unit characteristics, extraction height and column of primary ore. The model is developed from observations of fragmentation measurements in different mine sectors of Codelco’s El Teniente mine in Chile.This work focuses on the following three steps:collecting fragmentation and hang-up data from several mine sectorsdeveloping a geotechnical block model using oriented core placed within the main geotechnical unitsanalysing the data and modelling the fragmentation process.The proposed model is used to discuss the mechanisms and the influence of preconditioning on the size of the ore fragments that report to the drawpoints.CITATION:Brzovic, A, Vallejos, J, Arancibia, E, Burgos, L, Delonca, A, Gaete, M and Barrera, V, 2016. Analysis and modelling of the fragmentation process – case studies at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 305–310 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B C. Sarkar, D Ray, V Sarkar, P K. Sinha, R K. Singh, A Kumar

Estimation of iron ore grade distribution has been attempted using geostatistics and artificial neural network (ANN) based models for a banded iron formation (BIF) type iron ore deposit of East India. Geologically, it is a supergene iron ore formation through an enrichment process of parent material (BIFs) by gradual leaching of impurities, namely SiO2 and Al2O3. As the degree of leaching differs spatially, distribution of Fe varies depending on local controls of ore formation. While geostatistical methods work on models based on spatial correlations of mineralisation parameters, ANN models a non-linear distribution and is widely used as a global approximator. Spatial distribution modelling of Fe values has been carried out employing ordinary kriging (OK) and sequential Gaussian simulation (SGS). Non-linear modelling has been performed using hybrid neural networks (HNN) that provided an alternative option for grade estimation. Classical statistical modelling revealed a negatively skewed 3-parameter lognormal Fe population having a mean of 60.49 per cent with a skewness of -0.08 and a kurtosis of 2.60. Semi-variography and geostatistical estimation employing OK procedure led to block-by-block kriged estimates with associated kriging variance, which provided an overall mean kriged estimate and kriging variance of Fe as 60.29 per cent and 7.76 (per cent)2 respectively. SGS procedure revealed a mean of 60.71 per cent and a standard deviation of 5.89 per cent with minimum and maximum values as 45.12 per cent and 68.70 per cent respectively in respect of Fe. HNN model provided values of mean squared error (MSE) and correlation coefficient (R2) as 12.33 and 0.61 respectively, thereby exhibiting the robustness of the model to sustain maximum heterogeneity within the target domain. A comparison of Fe grade estimates obtained by kriging, simulation and HNN models more or less maintain similar distribution patterns that are close to the sample data. It is thus opined to carry out the grade prediction exercise employing all these three modelling approaches to obtain alternative scenarios for improved mine planning and design exercises. The techniques provide a foundation for cogent grade modelling leading to improved iron ore reserve estimation procedures.CITATION:Sarkar, B C, Singh, R K, Ray, D, Kumar, A, Sinha, P K and Sarkar, V, 2017. Iron ore grade modelling using geostatistics and artificial neural networks, in Proceedings Iron Ore 2017, pp 431–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By S Lehane, S Pearce

The characterisation and assessment of waste rock has been the subject of considerable research, and many guidance documents have been published both internationally and within Australia. While these documents provide detailed information on how to characterise waste rock, there is not a great amount of detail on how to determine the optimal waste management options from an operational viewpoint. For example, typical questions that a mine operator would seek answers to include: What placement method should be used (eg end tipping versus paddock dumping)? What is an optimal tip head height for waste placement in a storage facility? How should sulfide grade control be carried out?Defining the contributing factors to waste management and waste material placement and assessing the contribution of each variable directs these assessments towards a semi-qualitative and quantitative methodology. Quantitative methodologies show an increase in the confidence of these assessments by providing logical, measureable assessments.As part of a strategic assessment for waste management at an active mine site, a detailed risk-based investigation of the influence of variables common to waste placement was completed. These variables included placement method, placement height, sulfur grade and material conditioning (eg compaction) on the associated risks of waste material storage. The assessed risks include temperature assessments (potential for thermal take-off as a result of spontaneous combustion), toxic gas production and flow and acid production potential. Applying a numerical modelling approach to the assessment of the different waste material placement strategies allows for the variation in risk to be graphically presented and communicated through risk matrices and histograms.CITATION:Pearce, S and Lehane, S, 2015. Quantitative risk assessment tools to assist with waste management and placement guidelines, in Proceedings Tailings and Mine Waste Management for the 21st Century, pp 353–364 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By B Powell

Coastal acid sulfate soils (ASS) are wetland soils and unconsolidated sediments that contain iron sulfides which, when exposed to atmospheric oxygen in the presence of water, form sulfuric acid. ASS form in protected low energy environments such as barrier estuaries and coastal lakes and commonly occur in low lying coastal lands as Holocene marine muds and sands. When disturbed, the iron sulfides in these soils can oxidise and produce large volumes of sulfuric acid (essentially similar chemistry to acid rock drainage with mines) resulting in the subsequent release of toxic levels of iron, aluminium, manganese and possibly heavy metals. This results in detrimental effects on aquatic biota, plants, animals and steel/concrete structures and on human health in the surrounding environment. There are an estimated 2.3 million ha of ASS located along 6500 km of the Queensland coastline. In contrast to many mineral sulfides encountered in the mining industry, the pyrite crystals in ASS can be as small as 2 mm and commonly occur as framboids with extremely large surface area per unit mass, substantially increasing their reactivity if exposed to air (oxidation). Highly reactive iron monosulfides can also occur, particularly in drains and shallow lakes. Many coastal areas, where some 80 per cent of the population of Queensland reside, are coming under pressure for agricultural and urban development. Construction of canal estates, marinas, housing/industrial estates, roads, golf courses, aquaculture ponds, sand/gravel extraction and drainage for sugar cane can disturb ASS and release sulfuric acid, which may then drain into adjacent waterways with heavy rain. As development continues to encroach on coastal lowlands, the identification, quantification and management of ASS must be addressed as part of a commitment to the principles of Ecologically Sustainable Development (ESD). ASS can be successfully managed by adopting best practices and following guidelines, but government, community and industry must collaborate to raise awareness, avoid æhot spotsÆ and develop more cost-effective solutions. Scientists led the education and public awareness program showing infrastructure and environmental damages arising from ASS in Queensland. Using results from mapping and research, they convinced policy makers, industry and polititians to accept the need for legislation founded on good science. The resulting æState Planning Policy 2/02: Planning and Managing Development Involving Acid Sulfate SoilsÆ identifies the StateÆs interest in acid sulfate soils. The Queensland Government considers that development involving acid sulfate soils in low-lying coastal areas should be planned and managed to avoid potential adverse effects on the natural and built environment (including infrastructure) and human health. SPP 2/02 states where the policy applies and when a development application will trigger the policy. It can also be used to assist local governments in preparing their planning schemes under the æIntegrated Planning Act 1997Æ. The SPP 2/02 comes with a æState Planning Policy 2/02 GuidelineÆ to provide advice and technical information on interpreting and implementing the SPP 2/02. This guideline has legal status in assisting in the interpretation of SPP 2/02. Those seeking more detailed technical information can now also access the æSoil Management GuidelinesÆ and ASS æSampling GuidelineÆ, available from the Department of Natural Resources and Mines website. These are some of a series of chapters being developed for the æQueensland Acid Sulfate Soil Technical ManualÆ.

Jan 1, 2003

One of the most important goals of the experiments is to determine deformation and strength of the rock specimen under applying triaxial load, the status of failure condition is one of the subjects which can be used in soil mechanic and foundation engineering applications. To investigate the effect of confining pressure on the triaxial test, the rock has been considered as bonded-particles method and has been simulated by particle flow code three dimensions (PFC3D). This model, does not have pre-existing microcracks and all the particles have the same size (2 mm diameter), equal to the real specimen shape. To compare the mechanical behavior and failure pattern of the numerical and experimental results at uniaxial and triaxial tests at the same conditions, the Young's modulus, Possion's ratio as well as maximum axial stress have been considered. On the other hand, the microcracks growth and change of failure pattern at the modelling of the uniaxial and triaxial tests with different confining pressures up to failure point were reported. According to the experimental work, the number density of microcracks decreases from starting value and remains almost constant up to the failure beyond that point. The comparison of the numerical and experimental results of maximum axial stress and the Possion's ratio revealed good accordance. The initial number density of microcracks at the model was zero and increased while microcracking. Also, the sudden increment around the maximum stress was observed which is because of unstable growing of microcracks near the maximum stress. In all uniaxial and triaxial tests with different confining stresses, the number density of microcracks during the failure remains almost constant which can be considered as a proof of failure occurring in the model. The experimental results indicate the similar trend as well.

Nov 25, 2010

By T Rohde, P Defferrard

In 2010 a store and release cover (the cover) was constructed on the south waste rock dump (SWRD) at Century mine. This also included aerial seeding of province native trees and shrub seeds. The purpose of the cover is to reduce percolation into the potentially acid-forming (PAF) waste rock by maintaining a compacted reduced permeability layer (RPL) at near-saturated conditions. This is achieved by overlaying the RPL with a 1.5 to 2 m thickness of soil-mulch. The soil-mulch has a hummocky final surface that captures rainfall, so it does not runoff, allowing it in part to infiltrate, with excess water removed by evaporation and transpiration. The RPL is the trafficked surface of the SWRD.The unsaturated behaviour of the cover is being monitored by instrumentation including volumetric water content and matric suction sensors and a weather station capable of estimating evapotranspiration. The instrumentation allows for direct measurement of infiltration into the cover, storage of rainfall, percolation through the base of the cover and in situ soil water characteristic curves (SWCC).The key functions used to describe the unsaturated behaviour of the cover materials is the SWCC and the unsaturated hydraulic conductivity function. The SWCC is a plot of soil water versus soil suction. It provides the loci of moisture states of a soil from the saturated to the dry state.The paper presents the results of five years of monitoring. It shows that total infiltration into the top of the SWRD was about 1.6 – 3.7% of cumulative rainfall over five years, with most of the infiltration going into storage within the cover. Runoff from the top of the dump is not allowed therefore, the remaining 95% of the total rainfall was lost to evaporation or as lateral flow when infiltration reached the RPL. The paper presents some simple analyses of the wetting by rainfall infiltration of the cover, leading to breakthrough at the base. Field data are used to support the analyses.Presentation of the SWRD water balance is also included in the paper using SVFLUX™GE which is a finite element model that simulates water transport through a saturated or unsaturated medium.CITATION:Defferrard, P and Rohde, T, 2018. Five years of cover performance monitoring and modelling for a store and release cover at Century Mine, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 179–189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D McCoy

Titanium feedstocks are the building blocks of the titanium value chain. They can be mined directly, as is the case for ilmenite, leucoxene and rutile, or manufactured from ilmenite by extracting various quantities of non-TiO2 components from the ore by chemical and/or thermal processes.While feedstocks can be grouped into categories of materials with similar characteristics, they are essentially unique products from very different mining locations around the world. In fact, no two feedstocks are exactly the same. As such, the variations between the available feedstocks, in combination with the permutations in processing technologies to turn the feedstocks into titanium pigment or metal, mean that choices between feedstocks are specific to the location in which they are utilised.In this paper, the authors examine the key requirements of titanium feedstocks to the TiO2 pigment and metal sectors. Apart from the well known differences between feedstock choices for the sulfate and chloride process, the more opaque considerations in feedstock sourcing are examined.

Oct 5, 2011

High Pressure Sulfuric Acid/Oxygen Leaching of Platinum Group Metals Bearing Ni-Cu Mattes The processing of platinum bearing Ni-Cu ores for the extraction of platinum group metals (PGMs) involves comminution, flotation, smelting, and converter treatment of the furnace matte. Leaching circuits are predominantly used for further processing to separate the base metals and PGMs contained in the converter matte. Nickel dissolution is primarily achieved in the first stage leach (high pressure or atmospheric leaching, or a combination of the two), which is followed by second stage high pressure sulphuric acid/oxygen leaching to dissolve copper and the remaining nickel. PGMs are recovered from the leaching residue in downstream processes, and their dissolution in the first two leaching stages must hence be limited. Studies have been conducted to investigate the leaching mechanisms and kinetics of base metals in different leaching environments. The key operating parameters that influence the leaching kinetics of these metals include the temperature, acid concentration, degree of agitation, feed particle size distribution, and oxygen partial pressure. There is, however, a limited understanding of the behaviour of PGMs in the high pressure leaching process. Consequently, this process is controlled based on operators' intuition despite its importance in the recovery of PGMs. An improved fundamental understanding of the behaviour of PGMs in this leaching environment is required to be able to accurately model the process. This in turn will allow the development of an improved control strategy and the estimation of optimum operating conditions. An overview of the leaching mechanisms of base metals and the effects of key operating parameters on their dissolution kinetics in different leaching environments are presented. Models that have been developed to predict the leaching behaviour of base metals are discussed and evaluated. Finally, initial results obtained with an experimental setup that will be used to investigate the behaviour of PGMs in high pressure leaching systems are discussed and compared with published results.

Sep 13, 2010

The New Zealand Steel Ironsand Slurry Pipeline was successfully commissioned in February 1986. The project includes 18 km of high pressure, polyurethane lined buried pipe. McConnell Dowell Constructors Limited has developed a coupling which has allowed this pipeline to be fully welded. The design and development of the coupling and its application on this project is discussed.

Jan 1, 1986

By K Williams, W Chen, J Miller

The flow function of an iron ore material governs its flowability characteristics in material handling chains within the resource industry. A uniaxial compression test is able to obtain a flow function more rapidly comparing to the Jenike direct shear test; nevertheless, the results often exhibit lower rankings using the former method. This study aims to investigate the fundamental stress states within the test specimen that lead to this phenomenon, and to introduce a new uniform density specimen preparation method for a uniaxial compression test, in order to achieve comparative flow functions as for a Jenike direct shear test. The minimisation of the wall friction effect and achievement of the critical state when preparing a uniaxial specimen are explicitly discussed. Experimental investigations on flow functions of a suite of Australian iron ore samples were conducted using both the uniform density uniaxial compression test and the Jenike direct shear test. Results from both methods were found to be comparable, providing the specimen exhibits cohesive flow behaviours. The outcome of this research enabled development of a rapid and reliable flow function testing method for cohesive iron ore materials.CITATION:Chen, W, Williams, K, Roberts, A and Miller, J, 2017. Rapid and reliable flow property testing – a modified uniaxial approach, in Proceedings Iron Ore 2017, pp 149–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

Gold was first discovered in the Shotover by Thomas Arthur in 1862. He left his job as a shearer and soon there were up to 3000 miners working over the length of the river. Some parts were extremely rich and a few early miners recovered as much as 300 ounces in a day. From these early days of hand working the operations progressed through to hydraulic elevating once water races and pipes were installed after the Skippers road was completed about 1890. The riverbed was worked in paddocks with .the gravel being sluiced to a central suction which elevated the material over a sluice box. Use of this system continued intermittently through until 1977 when Joe Schieb retired û the last of the hydraulic miners. Many bucket ladder dredges worked on the lower Shotover near Big Beach where the Sew Hoy family recovered a lot of gold. Just after 1900, at least three worked further upstream, one on the beach where Shotover Jet now operates and one further up below the Moonlight. All the sections for this were transported in over the Moonlight Track and the boiler, steam engine and bucket ladder are still sitting at the edge of the river. up near Maori Point a dredge operated from Dredge Slip upstream. Records are poor on these dredges but they all suffered from the frequent floods and large boulders which damaged the bucket line. The last dredging attempt was about 1930 when a suction dredge was constructed on Maori Beach. This failed as seems to be normal for most suction dredging ventures. The river can drop to very low levels in the middle of a dry summer, and in winter when the water is tied up in the mountains as ice and snow. During 1863 when heavy rain melted snow in the high country, the river rose 35 feet overnight and drowned many miners camped on the banks. The ever present risk of flooding dominates the method of working and plant design.

Jan 1, 1987