Search Documents

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

By L Lorenzen, H Muller, L Bernard

Australian companies and consultants are becoming ever more involved in projects in African, South American, East European and Middle Eastern countries. However, significant differences in culture and approach to projects sometimes make these projects challenging for reasons that are not purely technical. Often the challenges are rather related to how the project owner and local authorities perceive the reality. These perceptions and sometimes unrealistic expectations regarding project costs and potential outcomes need to be addressed by the æWesternÆ project developer and consultant.This paper will discuss the specific experience of Snowden in studies commissioned by companies from such countries for the development of very large, low-grade gold deposits in some of the most inhospitable areas in the world. The paper will further review similar projects undertaken in other ænew worldÆ countries and compare these to the initial Snowden experience.As the process operating costs of operations in many of these countries are extremely competitive when compared to the typical Australian operating costs, the paper will review the operating costs and the factors which may be pertinent to a large project of this nature, both in the Australian and the ænew worldÆ context. Will Australian-based operations be able to compete in the global gold market when the gold price softens again, as it will do at some stage in the possibly not-so-distant future?CITATION:Muller, H, Lorenzen, L and Bernard, L, 2013. Challenges of developing low-grade deposits in ænew worldÆ countries from a mining consultantÆs perspective, in Proceedings World Gold 2013 , pp 307-314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

The Gold Ridge Mine is an open-cut gold mine in the Solomon Islands. The mine is owned and operated by Gold Ridge Mining Limited, a wholly owned subsidiary of Ross Mining NL. At the invitation of the Solomon Island Government, project construction commenced in July 1997 and gold production commenced in August 1998. The mine is the countryÆs first, and represents a major milestone in the development of the Solomon Islands. At the time of project approval and construction, there was a growing awareness in the country of the potential impacts of mining in the tropics, partly due to unfavourable publicity surrounding a number of other mining operations in the Pacific region. The management of environmental impacts was therefore an important consideration in the approval of the project, and continues to receive a high level of attention from the Government and community. Ross Mining did not commit to the Gold Ridge Project until it had satisfied itself that all waste rock and tailings could be safely contained on-site, and that the standards normally expected of a mine in Australia could be met. Ross Mining approached the approval, construction, and operation of the Gold Ridge Mine with a set of operating principles that met Government and community concerns. These were:best practice environmental management; operation of the mine in accordance with standards expected of mining operations in Australia; independent peer review of key technical aspects; on-going consultation with Government and community; and equitable transfer of wealth to landowners and the local community. As a consequence, the Gold Ridge Mine has developed into a successful mining operation with a high level of support from local landowners, the general community and the Central and Provincial Governments of the Solomon Islands.

Jan 1, 1999

This paper talks about the experiences of groups we have worked with over the last few years in the Asia-Pacific region (Australia, Canada, New Zealand and Papua New Guinea) and the ways that they have worked to bridge the divide between traditional and introduced structures, governance at a regional level and the introduction of traditional values into monitoring and evaluation practices. In doing this these groups have created structures and processes which have helped them engage both more effectively with external stakeholders while maintaining the legitimacy of their own operations with their own constituents. These are important ideas for those involved in the mining industry that could provide a number of very tangible benefits to mining firms and their engagement with these kinds of groups.

Jan 1, 2009

By Y Cui, G Cao, H Zong, J Zheng, J Wang, S Yue, J Zhao, B Li

The iron (Fe) concentration in nickel slag is high, making its recovery and utilisation a hot and challenging topic. In the nickel smelting process, using CaO instead of SiO2 to adjust slag’s composition, and then directly reducing Fe from the output of molten slag is a more feasible method in practice for Fe recovery in nickel slag. The adjustment of slag’s composition in the nickel smelting process will have an impact on the distribution of impurity elements such as Pb, Zn, and As. In this paper, the slag adjustment of nickel smelting process was carried out with the oxygen-enriched topblowing system. The distribution of impurity elements in the smelting products with each composition slag was conducted by using thermodynamic software. Experimental verification was performed with rich oxygen top-blowing, and the distribution characteristics of impurity elements in the smelting products were characterised to explore the differences in mineral phases of impurity elements with each smelting conditions, elucidating the distribution patterns of Pb, Zn, and As in each phase. The results indicate that after slag adjustment, impurity elements are more easily to volatilisation and removal into the gas, reducing their total concentration in slag and matte. In the slag, the existence form of Pb, Zn is changed from silicate to ferrate, and As is changed from arsenate to low-valent arsenic oxide. It is easier to decompose the impurity-containing mineral phase and remove the impurity elements in the subsequent iron extraction process.

Jun 19, 2024

By S Barrow, D Kent

Controlling the access of equipment, and people, has become more critical over the last few years for improving productivity and to meet safety responsibilities imposed by legislated obligations to have safety management systems. Hence Mine Site Technologies (MST) has spent the last three years completing the development of the tagging system to meet the mining industryÆs requirements, particularly streamlining access control. The basic tagging system tracks active Tags carried by personnel, or attached to vehicles and equipment, within underground zones. These Tags are detected (read) by Beacons placed strategically throughout the mine. As a Tag, or Tags, go past a Beacon they are read and the information transmitted back to the main database PC. This allows the current whereabouts of personnel and equipment to be known, as well as the history of their movements. The objectives of implementing the TRACKER Tagging System at Oaky No 1 Coal Mine were to: maintain a count of personnel inbye a particular point, and can alarm when a pre-set number is reached (eg the limit imposed by availability of SCSRÆs, etc); maintain a count of vehicles (and vehicle type) inbye a point, and can alarm if when a pre-set number is reached (eg when rated diesel units exceeds the limit for the ventilation present in that zone); manage the vehicle fleet, by keeping track of various vehicles underground better control and dispatch management of the equipment is achieved; keep track of equipment, knowing the location of equipment (such as forks, baskets, pumps, fans, etc) where last used or stored will minimise the risk of losing gear and assist in keeping inventory to a minimum; and locate personnel in emergency situations, by placing read Beacons throughout the mine the location of all personnel can be known in real time so that in the event of an emergency, their withdrawal can be monitored.

Jan 1, 2005

By H Ishikawa, H Zhou, M Spagnolo, R Halomoan, S Palaniandy

The Karara Mine concentrator commenced operation in November 2012 to produce high-grade magnetite concentrate. The circuit consists of three stages of comminution plus magnetic separation at each stage for early gangue rejection. High-Pressure Grinding Rolls (HPGRs) are used for fine crushing, followed by ball mills and TowerMills in secondary and fine grinding duties respectively. In recent times, the plant throughput rate has had to exceed design by 18% to maintain the targeted concentrate productivity. Meanwhile, the ore hardness has increased by 25% to 15 kWh/t, leading to changes in the circuit operation and design. These changes led to coarser and harder feed to the TowerMill circuit that affects the subsequent separation processes. Nippon Eirich (the TowerMill manufacturer) has partnered with Karara Mining Limited (Karara) to optimise the TowerMill circuit operation to achieve a circuit product with an 80% passing (P80) of 35 µm. Several activities, including a TowerMill circuit audit and performance evaluation, multi-component analysis, modelling and simulation, were carried out as part of the optimisation exercise. The circuit audit results revealed that the TowerMill circuit feed size F80 had increased and ranged from 67–75 µm. The circuit product P80 ranged between 42–55 µm. The average circuit specific energy was 3.4 kWh/t. Moreover, the differences in density between magnetite and gangue minerals had affected the hydrocyclone performance where the efficiency curve exhibits coarse end deflection indicating that low-density coarse material was bypassing to the overflow stream. A multi-component analysis was carried out to further investigate the coarse end deflection of the hydrocyclone efficiency curve. The analysis showed that the magnetite and gangue minerals had different cut sizes of 32 and 64 µm respectively. Furthermore, 33% of the magnetite (below 35 µm) was being recycled back to the mill due to the density effect. Based on these findings, several recommendations for process improvement were identified and implemented including:• converting to a bottom feeding configuration to improve the grinding efficiency in the mill• additional grinding power in the fine grinding duty to compensate for the increase in plant throughput and ore hardness• improved classification efficiency by converting to smaller size hydrocyclones. Simulation studies carried out to evaluate the impact of these implementations had indicated that a P80 close to 35 µm with a steeper size distribution could be achieved by using the bottom feed configuration with additional grinding power. The TowerMill circuit was converted to bottom feed configuration and the performance was evaluated. The operating work index, size specific energy and circulating load were 30% lower than the top feed configuration, indicating that the bottom feed configuration had a higher grinding efficiency. This paper discusses the outcome of the circuit audit, multicomponent analysis, circuit simulations, improvement strategies and quantification of the improvements. CITATION:Palaniandy, S, Spagnolo, M, Halomoan, R, Zhou, H and Ishikawa, H, 2017. Fine grinding circuit process improvement at the Karara mine concentrator, in Proceedings MetPlant 2017, pp 101–120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By R C. A Minnitt

The Witwatersrand Supergroup is host to the world’s largest gold deposits. The location, quantity, grade, continuity and other geological characteristics of a Mineral Resource are either known, estimated from specific geological evidence and knowledge, or interpreted from a well constrained and portrayed geological model. Establishing such a model is an integral part of the evaluation process in the Anglogold Ashanti (AGA) group, and is referred to as a Geoscience Business Model for the mining operations. The geological model established over the years has relied on detailed descriptions of the mineralisation, and understanding of the regional and local geology of the Witwatersrand sediments, in the West Wits and Free State goldfields. The processes of data collection in regard to underground stope and developing mapping, structural and sedimentological mapping, and the geological inputs to mine planning systems are described, together with aspects of drilling, sampling, grade control, and data management. Anglogold Ashanti’s Geoscience Department employs a complex and unique process to generate the Mineral Resource, including a 3D geological structure model of the orebodies which are usually highly faulted, and a robust mineralisation/facies model on which the decisions about domain boundaries are established. A Mineral Resource Inventory System (MRIS) has a dynamic graphic interface to the resource database that is used for compiling the resource statement. It is also used to determine the gold-called-for, as well as short and long-term planning. A unique estimation process using the extensive closely spaced stope face sampling database and the more widely spaced surface drilling information is used in combination in the Macro Co-Kriging estimation. The use of different support sizes in the C0-Kriging process is preceded by the equally unique ‘clusterisation’ and ‘acceptorisation’ procedures by which the data are quality controlled and assured prior to their use in the kriging process. The Mineral Resource and Ore Reserve estimates are classified according to the SAMREC code through a method that ensures that they are compliant, auditable, transparent and reconcilable with previous Mineral Resource and Ore Reserve statements.

Aug 22, 2011

By D A. Bowman, S Schafrik

With the goal of reducing injuries and fatalities related to haul truck accidents, this research investigates technologies and intervention strategies for improving worker training using a virtual environment (VE). Funded by the National Institute for Occupational Safety and Health (NIOSH), this research specifically focuses on training workers in preshift inspections of haul trucks to avoid preventable defects from causing worker injuries and expensive equipment damage. Improved training in these inspections is expected to increase uptime. The VE developed to train workers for preshift inspections consists of three phases: the virtual tour, the virtual inspection and the shift simulation. The virtual tour introduces information necessary to conduct a preshift inspection by guiding the worker around a haul truck, identifying parts to be inspected and explaining defects to look for. The virtual inspection assesses retention as the worker navigates around a haul truck and identifies defects. During the shift simulation, the worker is shown a simulation of the work shift, which animates severe consequences of any overlooked defects to emphasise the importance of preshift inspections. To provide multiple training platforms, desktop and CAVEÖ versions of the training VE were created. Flux Studio was used to model the environment and to produce Virtual Reality Modelling Language (VRML) files for the desktop version. DIVERSE, an application programming interface, was then used to implement a more realistic version of the VE in a CAVEÖ, a room-sized visualisation system. Initial feedback from mining colleagues indicates that the training VE may replace normal classroom training for preshift inspections in the future. As opposed to PowerPoint presentations and instructional videos, the training VE provides better spatial understanding of the location of parts and incorporates interactive features to actively engage drivers in the learning process, which may result in better retention. Initial feedback also indicates that minor improvements can be made to the virtual tour and virtual inspection phases.

Jan 1, 2008

By M Z. Abzalov

Drilling mineral sand deposits has specific challenges, which are different from drilling hard rock deposits: Drilled sequences are represented by non-consolidated free-flowing sands to semi-consolidated clayey sands and indurated layers. Valuable heavy minerals (ilmenite, rutile, zircon, leucoxene) have an average density of 4.6 g/cm3, which is significantly heavier than the hosting sand matrix; mainly represented by quartz (density = 2.6 g/cm3). The large difference in the mineral densities can result in sample segregation in the drilling rods and capturing devices causing biased composition of the recovered samples. The drilled strata can contain beds of consolidated sediments, hard pan lenses and concretions. Therefore, chosen drilling equipment should be flexible and permit a switch from drilling the free-flowing sands to hard rock drilling. Thickness of the sand hosted mineralisation varies from several metres to more than 170 m. Mineralisation is distributed above and below the water table. Evaluation of the mineral sands deposits is based on hundreds of drill holes and many thousands of samples, therefore drilling methods should be fast and cost effective. The drilling methods commonly used for mineral sand deposit evaluation, include aircore, triple tube diamond and sonic; including its variants, such as vibrocore drilling technique. The ability of the studied drilling techniques to properly address the above listed challenges in mineral sand deposits, whilst maximising the quality of the obtained samples has been compared in three deposits: Corridor Sands (Mozambique), Richards Bay (Republic of South Africa) and Fort-Dauphin (Madagascar).This study has shown that aircore samples tend to be negatively grade biased, underestimating the heavy minerals content, in particular when drilled intervals are located below the water table. Triple tube diamond core method can produce non-biased samples. However, results can be marred by incorrectly chosen drilling mud. Sonic drilling is a relatively new technique based on a high frequency vibratory technology. It is the only production drilling technique that allows a continuous relatively undisturbed sample of unlithified sands to be obtained. The main limitations of this technology preventing its wider use for developing mineral sand resources are the relatively high drilling costs, in particular when the depth of drilling exceeds 100 m, and speed of drilling advance.

Oct 5, 2011

By L Snyman, S Webster and J Samosir

Northparkes is located 27 km north of the township of Parkes in central New South Wales, Australia. The operations consist of underground block cave mines and an ore processing plant, which produces high-grade copper and gold concentrate. Production is currently sourced from the E48 Lift 1 block cave mine and open cut stockpiles. Mining commenced at Northparkes in 1994 as an open cut operation. Underground block cave mining began in 1997. Northparkes was the first mine in Australia to use the highly efficient block cave mining method, which relies on gravity and natural rock stresses to fragment and recover the ore.The E48 extraction level is located approximately 581 m below surface and consists of ten extraction drives and 214 drawpoints. Several stress measurements carried out at various levels in both E26 and E48 indicated a low underground regional stress environment and a low to moderate stress state in the E48 orebody. The E48 block used a post undercut strategy that was initiated in 2009, with production commencing in September 2010 and cave-through to the surface occurring approximately four months later in January 2011. Changes to the cut-off grade and fixed prices meant that Northparkes was able to develop an additional two drives to the north of the existing cave and one additional drive to the south. Modelling of the cavability of the additional drives indicated that the cave would not readily propagate to sufficient height of draw to mobilise the ore and tended to arch over to the existing cave shape. Based on modelling and a desire to reduce the risk of the project, preconditioning was adopted. Along with the requirement of safely hydrofracturing an active cave, a measure of the success of the preconditioning was desired. Few block cave operations have developed extension drives adjacent to existing caves.This paper summarises the lessons learnt from the development of this extension project, with a specific focus on ground control and monitoring.CITATION:Snyman, L, Webster, S and Samosir, J, 2016. E48 cave extension at Northparkes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 111–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M D. Melville, B C. T Macdonald, J Dixon

The acidic and metal rich waters that are generated from acid sulfate soil (ASS) drainage can have damaging impacts upon ecosystems. The most obvious impact has been the discolouration of water and occasional fish kills. ASSÆs produce these acidic and metal rich waters when pyrite in soil is oxidised. Land management techniques are an essential long-term requirement to minimise the amount of pyrite oxidation. Acidic water that cannot be prevented through land management can be neutralised by other techniques. Powdered lime is the most common material in agriculture that is applied directly to soils and waters. Powdered lime can be expensive and if applied dry it may aggregate. Since the aggregated particles of lime are larger they could sink rapidly in the water column and not react. In waters with high concentrations of dissolved iron and aluminium the lime particles may become coated with a metal oxy-hydroxide precipitate, which will decrease its reactivity. A unique lime-dispensing machine, the Waterways Lime Spreader, has been developed to neutralise acidic waterways. The Waterways Lime Spreader can produce a solution rich in fine lime from larger limestone fragments. The current size of the machine means only 3.5 grams per second of limestone can be emitted. This output will neutralise low acidity waters, however, for high acidity waters the time for neutralisation can be long. More reactive chemicals such as hydrated lime or increasing the size of the machine will reduce this neutralisation time. The Waterways Lime Spreader is also capable of producing slurry mixtures if powdered materials are required. Trials with the Waterways Lime Spreader were undertaken in part of the Clothiers Creek catchment located in northeast NSW, Australia. A small drain with a water volume of 4 m3 was neutralised with crushed limestone to pH 6.9 from an initial pH of 2.6 and an acidity of 902 mg/L CaCO3 in 160 minutes. In comparison a drain with a slightly larger volume of 6 m3 that had an initial pH of 3.2 and an acidity of 753 mg/L CaCO3 was neutralised with hydrated lime to pH 11.8 in five minutes. The Waterways Lime Spreader has been used successfully to neutralise water from acid sulfate soils. It is expected that future applications of the machine may be for the neutralisation of acid rock drainage or acidified lakes.

Jan 1, 2003

Mineral Processing Education in China

Sep 13, 2010

Most people are familiar with Euclidean dimensions: zero for a point; one for a line; two for a plane; and three for a volume. Howeverbobjects are not actually Euclidean, but lie somewhere between Euclidean æend-membersÆ with a non-integer fractal (or æfractionalÆ) dimension. The fractal dimension D is a measure of the relative importance of large versus small. Consider the trace of a coastline on a map. It has a fractal dimension (1 =D =2) somewhere between a line (dimension = 1) and a plane (dimension = 2). The more tortuous the coastline, the higher the fractal dimension, and the closer it becomes towards a plane. The concepts of fractals and spatial geometry can be applied to a wide range of geologicaVmining problems as well as than those dealing with space. One commonly quoted fractal relation is the log-log relationship of ore-grade and tonnage. Until recently, we have never been able to define or measure spatial-geometry, but new developments in mathematics have provided a means by which to quantity and apply it to our problems.

Jan 1, 1992

Study on Beneficiation Technology of a Refractory Fluorite Ore in North China

Sep 13, 2010

LIST OF CONTENTSAbstractIntroductionSelected Sections of the Broken Hill LodeLocality PlansPetrology1. Zinc Corporation Mine: DDH. 5.98, section 30, No. 26 level2. Zinc Corporation Mine: DDH. 838, section 30, No. 13 level3. Broken Hill Sonth Mine: 60 ft. cont01(r above 1170 ft. level4. Broken Hill South Mine : No. 7 shaft section, 1370 ft. levelOrigin of garnet sandstone5. Barrier Central Pty. Ltd.: DDH. tJ.93, Block 136. North Broken Hill Ltd.: Junction mine, DDH. 602, No. 10 level7. North Broken Hill Ltd.: Jnnction mine, DDH. 588, No. 11 level8. North Broken Hill Ltd.: North mine, DDH. through Southern ore body, 3370 ft. level9. North Broken Hill Ltd.: North mine, Northern ore body above 2300 ft. level(a) Southern end, section 27, 77 ft. above rails(b) Northern end, section 30, 6.9 ft. above rails(c) Miscellaneons samples, sections 27 and 28Relative time of ore depositionSericitizntionStructural significance of sericitizationGCLhnite OrthoclaseApatite GarnetManganese SilicatesAlteration of manganese silicatesRelation of zinc and lead to the silicatesZinc in manganese-bearing silicatesLead in potassium and lime silicates and apatite

Jan 1, 1959

By D Frost, G Harbort, T Lipiec, N Deonarain

"The use of flotation columns has remained a contentious issue among mill operators. There are those who consider them an essential part of any mineral processing operation, while others consider them a necessary evil, which should only be installed if there is no alternative. Lastly, there are those who believe they should not be installed, no matter how great the perceived benefit.This paper provides an analysis of over 4000 installed flotation columns, contained in the Amec Foster Wheeler flotation database. Changing trends in column flotation use by type, commodity and geographical region are discussed. The effect of changing commodity prices and the China ‘phenomenon’ are reviewed. Special reference is made to the changing face of column flotation in Australia.Of note is the fact that after falling to a 20 year low in installed flotation column capacity in 2014, flotation columns during 2015 went through a resurgence in popularity. This resurgence was in direct contradiction to depressed metal prices and was driven by brownfield optimisations to reduce off-site costs, particularly in base metals. A case study is presented comparing the benefits of column flotation at high commodity prices with low commodity prices.Citation:Harbort, G, Deonarain, N, Frost, D, Lipiec, T and David, D, 2016. Changing Trends in Column Flotation Use - Their Impact for Australian Mill Operators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 93–104 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S H. Algie, D P. Taplin, S G. Doig

"Suboptimal performance of clusters of hydrocyclones (cyclones), relative to the performance of the individual cyclones that comprise the cluster, is a common phenomenon. The primary cause is well known: uneven distribution of the slurry feed into the individual cyclones. The direct result of uneven distribution is that each cyclone in a cluster performs somewhat differently. Hence, some, if not all, of them do not work at their intended operating points, and the classification is not as sharp as intended. The impact on grade, recovery and milling efficiency will vary depending on the duty of the processing circuit, but the most immediately apparent consequence of uneven distribution is a difference in wear rates in the individual cyclones; this exacerbates the problems of unequal performance of the individual cyclones. In severe cases, and as differential wear proceeds, flows from the individual cyclones may become visibly different. Uneven distribution, once the phenomenon was identified, was seen to be a significant issue in the high-solids hydrocyclone cluster in the ball mill recycle section of Evolution Mining’s Edna May Operation (EMO, Westonia, Western Australia) gold processing plant. In 2012, a FloCEP® hydrocyclone feed distributor system was installed to alleviate the problem. Over the next four years of operation, this innovation has proven its value in the metallurgical and maintenance areas. Individual cyclones now wear at the same rate, greatly reducing the need for operator intervention, as well as increasing overall plant availability through minimising unplanned maintenance. The costs of the installation can be justified by savings in maintenance alone, though the greatest value, as is described in this paper, is in allowing the plant to produce consistently closer to its operational design limits. The FloCEP® system is a low maintenance, readily installed retrofit, based on two patented devices that are combined with complementary proprietary design methodology allowing customisation for specific flow rates and slurry particle properties. Together, these devices produce and distribute a pseudo-homogenous slurry flow without moving parts.Citation:Taplin, D P, Doig, S G and Algie, S H, 2016. Experience with FloCEP® Slurry Flow Conditioning at Evolution Mining's Edna May Operation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 251–260 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By M Edwards

The paper outlines the successful application of some of the on-belt technologies available from Scantech International Pty Ltd and how these have provided benefits in a number of mining and mineral processing operations. Effective process control requires real time analysis so quality can be fed back to the previous process and fed forward to a subsequent process. A range of on-belt analysers that allows for full stream, continuous, non-contact analysis of conveyed materials is available to achieve this. Real time results can provide timely information for effective process control. Benefits of on-belt analysis systems become more evident once the true variability of material quality and moisture content in conveyed flows is measured. To obtain economies of scale in mineral processing operations large material flows are achieved using conveyors. The cost and effort to sample representatively increases as conveyor flows increase. One sample may represent a few tonnes or up to 10 000 tonnes of material. The turnaround time between sampling and availability of sample analysis data does not allow real time process control. Tonnage flow rate, moisture content and elemental or mineralogical composition are required to perform effective process control of most conveyed streams. Tonnages can be effectively measured using belt weighers. The analyses derived from small samples supplied by conveyor-based sampling systems contain high variability. On-belt, continuous analysers see all the material and, through short term compositing of analyses, supply less variable results. Real time analysis helps operators develop a better understanding of material variability. Analysers can be effectively utilised to improve the consistency of product quality through bulk sorting and blending control. Many existing users of the technologies have gained competitive advantages through their ability to supply a more consistent quality product to the market.

Jan 1, 2008

By D Martin

The Rio Tinto (Mount Bruce Mining Pty Ltd) Koodaideri Iron Ore Project is located approximately 110 km north-west of Newman in the Pilbara region of Western Australia. During detailed ecological studies of the project area, a significant maternity roost (containing around 430 individuals) of the Orange Leaf-nosed Bat (OLNB) (Rhinonicteris aurantius) was discovered within the boundaries of the proposed mining area. The OLNB is listed as Vulnerable under the Commonwealth Environment Protection and Biodiversity Conservation Act 1999 and is listed as a Schedule 1 species under the Western Australian Wildlife Conservation Act 1950.With a good understanding of blast vibration attenuation in the Pilbara’s different geologies and in the absence of other known studies, it was considered that appropriate buffer distances between mining and bat colonies were not scientifically determined. Therefore, to inform the environmental approvals process that was underway, a series of seismic blasts was planned to assess and measure the sensitivity of the OLNB to trial-sized seismic blasting activities to develop a more scientifically based buffer zone for the protection of the OLNB. This was to be achieved by testing ground attenuation of the site and measuring any response from the OLNB to the firing of seismic charges. Rio Tinto sought the independent expertise of ecological consultants to evaluate and participate in the work to quantify the level of sensitivity of the bat colony and to outline the proposal to government authorities.After detailed risk assessment and project mapping, the seismic blasts were implemented, with the aim of firing individual charged and measured vector peak particle velocity (VPPV) at the OLNB roost cave, combined with monitoring OLNB disturbance activity within the roost that was invoked by the blasts. A series of six charges were fired with the VPPV ranging from 0.66 mms-1 to 18.70 mms-1. The OLNB activity was monitored using high frequency microphones, which detect bat calls emitted during flight. Under daytime conditions, the bats would normally be dormant, so the null hypothesis was for no calls to be detected if the bats displayed no disturbance behaviour. This work has improved understanding of mining activities (blasting) on the OLNB species, assisting in establishing mining exclusion zones that are based on scientific data, contributing to a sustainable future for both the environment and the mining industry.CITATION:Martin, D, 2015. Scientific evaluation of fauna sensitivity to blasting, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 519–526 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015