Search Documents

By J Leppinen, B Johanson, R Kalapudas, G McMahon

The Suurikuusikko gold deposit was discovered in 1987 in western Finnish Lapland, 54 km NNE from the town centre of KittilS in the volcanic belt of Central Lapland. It is hosted by tholeiitic basalts in a graphite-bearing albitite breccia. The ore is located in subvertical shear zones characterised by strong albitisation, carbonatisation and sulfidisation. The ore minerals consist of arsenopyrite, pyrite, chalcopyrite, sphalerite, tetrahedrite, bournonite and rutile. Small amounts of pyrrhotite, gersdorffite, jamesonite, bornite, gudmundite, tetrahedrite, stibnite, kermesite, berthierite and native Sb are also present. Gold occurs as invisible and as 1 - 2 ¦m size inclusions in arsenopyrite and pyrite, on their grain boundaries and in fractures. The average amount of gold leached by cyanide is 2.93 per cent. The æinvisibleÆ gold contents were studied in pyrite and arsenopyrite by electron microprobe analysis (EPMA) and secondary ion mass spectrometry (SIMS) at CANMET/ MTL. Gold element distribution images show zoned patterns both in pyrite and arsenopyrite. SIMS analyses range from 343 to 55 ppm Au in arsenopyrite and from 217 ppm down to 0.32 ppm (detection limit 478 ppb) Au in pyrite. EPMA results range from 939 to below the detection limit 24 ppm Au in arsenopyrite and from 267 ppm to below 22 ppm Au in pyrite. Recovery of the refractory gold ore was studied using grinding, flotation, bio-oxidation and cyanidation tests. A sulfide bulk concentrate containing 40 ppm Au was obtained by flotation at 90 per cent recovery (As content 5.5 per cent, S content 22 per cent, and mass recovery 15 per cent). The grinding fineness in flotation was P80 -100 to 120 ¦m. At the original fineness the cyanidation recovery from the concentrate was lower than ten per cent, after ultra-fine grinding P80 -10 to 2 ¦m the Au recovery was less than 17 per cent. After bio- oxidation, Au recovery of 95 per cent was obtained in carbon-in-leach (CIL). The bio-oxidation time was two weeks in laboratory test, but after regrinding the oxidation rate was faster and recovery of Au higher. However, the selected method for the mining to be started in summer 2008 is open pit mining and mineral processing methods sulfide flotation and pressure oxidation in an autoclave. The ore reserves were estimated 31 December 2007 as: Probable 18.2 Mt with 5.1 g/t Au, Indicated 5.4 Mt with 3.0 g/t Au and Inferred 10.8 Mt with 3.4 g/t Au. The production capacity will be 3000 t/day.

Jan 1, 2008

By Ramsay WRH, Morand V

Structural, mineralogical, and textural data from the Tarnagulla Goldfield demonstrate that the area has undergone three significant phases of deformation. The first phase of deformation (Dl) predates the intrusion of the Tarnagulla pluton, which has been dated using K/Ar as 391 ¦ 5MY. We regard this pre-granite deformational event as the major regional deformation. Gold-bearing quartz veins have been deposited in dilational sites on west-dipping reverse faults. These sites demonstrate a geometry related both to faulting associated with Dl and the plunge of the Fl fold axes. This evidence, together with chronology of unmineralised ? D2 and D3 faults, the absence of quartz veining associated with D3 events, and the deformation of carbonate-quartz-biotite-sulphide aggregates within Sl by later S2, lead us to conclude that the bulk of the mineralisation was essentially syn- or late Dl. S'80 values for fluids in equilibrium with vein quartz from Central Victoria have indicated equivocal support for either a magmatic or metamorphic origin. Our evidence supports a pre-magmatic origin for mineralisation at Tarnagulla and hence tends to favour a metamorphic fluid source.

Jan 1, 1995

By N Belluz, L Johnson, N Wiwoho, P Manning

The Kucing Liar skarn deposit is located in the Ertsberg mining district, which also contains other skarn deposits and the Grasberg porphyry copper û gold deposit. The Ertsberg district is located in the province of Irian Jaya, IndonesiaÆs easternmost province. Mining development began in the Ertsberg district in 1972 with the mining of the Ertsberg deposit. Daily production in the district now averages about 230 000 tonnes of ore, with the bulk of the ore coming from the Grasberg open pit and the balance from underground mining of skarn deposits. During 1998, 45 218 additional metres of drilling were conducted to delineate and understand the Kucing Liar orebody. The deposit was first intersected in drill holes in 1994 and then was intersected in underground workings located about 1000 metres from the discovery drill hole in 1995. Initially, the two intersections were thought to be different orebodies but are now realised to be different parts of the same orebody. The Kucing Liar deposit consists of magnetite û copper û gold replacement and skarn mineralisation in favorable Tertiary and Cretaceous units. The deposit is approximately 2000 metres in length and averages about 200 to 250 metres in thickness. The width varies from 400 to 600 metres. Drilling in 1998 was directed towards delineating the deposit on its NW and SE ends and to determine its down dip extension. Reserves for the deposit at the end of 1998 stand at 320 million tonnes at 1.4 per cent copper, 1.4 g/t gold, and 5.3 g/t silver. Many important questions remain to be answered concerning the relationship of the Kucing Liar orebody to the major faults in the district and to the Grasberg intrusive complex which contains the Grasberg orebody. Continued exciting developments are anticipated as work to understand the deposit by drilling and geologic study continues.

Jan 1, 1999

By J Andrina, D Richar, R Smart, A Neale

The Grasberg is a large copper and gold open pit mine operated by PT Freeport Indonesia and located in the high equatorial mountains of Papua Province, Indonesia. The climate is alpine/sub-alpine with little seasonal variation in temperature and rainfall. The annual precipitation varies from about 3000 to 5000 mm over short distances around the Grasberg, but in general, an average daily precipitation of 10 mm per day applies and leaching of the overburden is continuous throughout the year. Mining commenced in 1988, and almost all of the overburden mined up to 2003 was potentially acid forming. From 2003 to the end of the Grasberg pit operation in 2014, approximately 70 per cent of the overburden will be potentially acid forming and 30 per cent limestone. A major focus of the investigations is developing strategies to maximise the beneficial use of the limestone that will be mined. Laboratory columns and field test pad investigations have been ongoing for six years examining limestone blends. Trial dumps utilising truck placement and conveyor/stacker placement and blending of limestone and acid generating rock have recently been constructed. In addition, based on initial results, investigations aimed at further evaluating the performance of limestone covers in this high rainfall environment have commenced. A significant finding has been the identification of strong armouring layers on sulfide surfaces within well-blended material and under limestone covers. These layers effectively isolate sulfides and thus progressively slow the oxidation rate to a level where the alkalinity load from the limestone exceeds the rate of acid generating. ARD is controlled and neutral low metal drainage results. The results have demonstrated that although limestone blending is effective, it is necessary to ensure that all size fractions within the blend receive adequate acid neutralising capacity to buffer the potential acidity. Because the sulfur content generally increases and the acid neutralising capacity decreases with decreasing particle size in limestone blends, the amount of limestone required greatly exceeds the stoichiometric requirement. This paper describes the development of limestone blending specifications for potentially acid forming overburden and presents the results of the ongoing limestone cover trials at the Grasberg mine.

Jan 1, 2003

By J Zhang, B Wei, T Zhao, K Wang

Understanding mining-induced surface movement and fissures is critical for environmental protection and geological prevention. In this study, image recognition algorithms, satellite remote sensing and unmanned aerial vehicle photogrammetry (UAVP) were combined to identify surface movement and fissures caused by mining, and a case study was conducted in a coalmine in western China, and the following conclusions were obtained.

Sep 1, 2024

By B Lavin, R Sanford

This paper examines the application of Lean Manufacturing in a mining environment, based on experience within the Rio Tinto entities: Rio Tinto Aluminium, Northparkes Mines and Hunter Valley Operations. The three applications have tested the flexibility of the Lean methodology. Within Rio Tinto, Rio Tinto Aluminium was the first group to introduce Lean. The rollout began in late 2004. It was introduced firstly at Boyne Smelters, Gladstone, as a model site with the initial application in the Carbon Bake Furnace area. It was later extended to other sites including the Weipa Bauxite Mine. LeanÆs successful application within Rio Tinto Aluminium was in part responsible for its recent adoption by other Australian-based Rio Tinto business units including Northparkes Mines, a copper mining operation in Central New South Wales, and Hunter Valley Operations, a group of four coal mines in the Hunter Valley region of New South Wales. Lean is also being adopted by Rio Tinto Iron Ore. Rio Tinto Aluminium introduced Lean Manufacturing to complement an existing Six Sigma business improvement program and to achieve continuous improvement activities at a workplace level. Lean provides a similar level of rigour and discipline to Six Sigma but its application is everyday and for everyone, everywhere in the workplace. It is a valuable management tool. In a short time, Lean has achieved good and sometimes spectacular results improving productivity and efficiency at all sites, including our mining site. Within Rio Tinto Aluminium, it has also had beneficial impacts on our ability to develop and retain employees.

Jan 1, 2006

The knowledge in the field has been reviewed by literature studies, and using experience from personal research in sublevel caving. There is a lot of material regarding gravity flow of fine grained materials in bins, but the theory of flow for these materials are normally not applicable for coarse blasted rock. This study was therefore concentrated towards coarse rock fragments created after blasting in orebodies. The goal for this study was to make a report of known knowledge, and identify what we have to learn more about. The Bergmark-Roos theory, which was a paradigm shift in the science of gravity flow, is today the best mathematical theory for calculation of the drawbody for a homogenous material or when we wish to simulate the mean drawbody for a large number of draws. The Bergmark-Roos theory must however be improved, so it can take into account the flow pipe effect. When this is done it will be possible to construct a 3D computer model for calculation of ore extraction versus amount of loaded ore and waste. It is also necessary to find the 3D shape of the flow cone to be able to calculate the 3D ore rest that normally develops on footwalls. Calculations should be done for the draw on several sublevels including determination of the ore losses and temporary ore rests. First when this computer model is developed optimisation of ore recovery and waste rock dilution can start for a given orebody. The author points out the importance for international co-operation and standardisation of methods for determination of material properties. More field tests and model blasting tests should also be done. When enough knowledge is gathered, a handbook of the optimisation of sublevel and block caving should be written.

Jan 1, 2000

By Flavelle IV

A survey is made of changes in the technical status of a number of western world copper extraction and refining operations over the past 20 years. Specific developments in pyro- and hydro-metallurgy and refining practices are identified together with factors in the changing environment of the industry which has influenced their adoption. Nickel extraction and refining is similarly discussed.The replacement of traditional technology by more attractive alternatives has occurred in a considerable number of operations. The develop-ment and status of new continuous smelting processes, advances in hydrometallurgy and refining innovations which emerged during the 1960s and early 1970s is discussed. The varying experience in commercial acceptance of these new technologies is noted.Finally some possible future directions are canvassed for both operators and the research and development institutions.

Jan 1, 1985

By J A. Sanchidrián

The general ranges of validity of some distribution functions are assessed from their behaviour with 119 sets of fragmentation data from bench blasting obtained by sieving. The emphasis is on determining the lower size/passing limit that the size-scaled Rosin-Rammler, Grady and Swebrec functions, and their bi-component versions, can represent with reasonable precision. By fitting these functions to the data using different weights, the accuracy of the fit varies in the different size/passing zones, so that an overall knowledge of the capacity of the function is obtained across the whole size range, from the coarse zone to the fines. Reasonable ranges of use of bimodal Rosin-Rammler and extended Swebrec (all of them five-parameter, bi-component distributions) are, in terms of percentage passing p, 99 > p > 2 per cent (up to 100 per cent for the extended Swebrec), or 90 > p > 0.5 per cent, in which the expected error of the calculated size is below 15 per cent in the extremes of the range, and less than five per cent in most of the central range; maximum errors (ie errors that will only rarely be exceeded) are typically less than 50 per cent in the central range, and up to about 100 per cent in the extremes. Ranges of use for the Swebrec and the size-scaled Rosin-Rammler (three-parameter distributions), with only slightly larger errors than the bi-components, are 100 > p > 5 per cent or 80 > p > 2 per cent. The classical two-parameter Rosin-Rammler can be used in the range 95 > p > 20 per cent or 90 > p > 10 per cent, with expected and maximum errors less than about 15 per cent and 100 per cent respectively.CITATION:Sanchidrián, J A, 2015. Ranges of validity of some distribution functions for blast-fragmented rock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 741–748 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Snowden D. V, Standing C. A, Ryba A, Bywater A

McKinnons open pit gold mine, located within the Cobar Basin in New South Wales, is characterised by complex mineralisation controlled by the intersection of steep faults in the hinge zone of an anticline. Resource estimation using indicator variography and indicator kriging was based on RC drilling on 25 in sections together with grade control RC drilling on 12 in by 12 in and 6 m by 6 in patterns. Rigorous sampling and checking procedures were used to verify the reliability of the drill hole data. Blast hole data was used to assist grade control in defining ore block boundaries.

Jan 1, 1997

By M Henderson, M Hudyma

Mining-induced seismicity at Junction Gold Mine became a serious operational problem in the late-1990s. Assessing the local seismic hazard is an important step in assessing the risk associated with potential rockbursting. This paper discusses the qualitative and quantitative means of assessing seismic hazard used at Junction. In qualitative hazard assessment, the role of the primary factors contributing to mining-induced seismicity and rockbursting are identified. These factors include: rock mass properties, geological structures, mine development, and stoping. A qualitative seismic hazard map has been developed considering these factors. In quantitative hazard assessment, seismic source parameters from an Integrated Seismic System are used to assess seismic hazard. The seismic source parameters found to be relevant to seismic hazard assessment at Junction are discussed.

Jan 1, 2002

By N Currey, G W. Wilson, P Ritchie

Kidston Gold Mine in Queensland, Australia has a 310 ha tailings impoundment that has undergone final closure rehabilitation. Kidston Gold Mine evaluated their closure options for this low acid generating tailings impoundment, and due to a lack of cover soils and the cost of importing material, the mine decided to investigate the possibility of direct vegetation onto the tailings impoundment surface. The mine subsequently embarked upon a well planned and detailed research program to determine the feasibility and sustainability of this closure option. The research program included vegetation trials, toxicology studies for metal uptake by vegetation, as well as a comprehensive closure water balance model for the tailings impoundment complex. This paper describes the results of the long-term closure water balance for the tailings impoundment complex for the pre-closure state of the impoundment, as well as predictions towards the impoundment performance once final rehabilitation of the tailings impoundment complex has been achieved. The water balance presented is unique in that it is founded on unsaturated flow principles and accounts in full the impacts of the surface flux boundary conditions. This novel approach enables the prediction of actual infiltration rates into the tailings impoundment surface, which in turn allows for the calculation of how much seepage will exit from the tailings dam toe drains.

Jan 1, 2003

By S D. Golding

The current study integrates hydrogeochemical and stable isotope results to investigate the sources and evolution of acid mine drainage at the historic Mount Morgan gold mine in Queensland, including the controlling factors and mechanisms of sulfate formation. The open pit and seepage sumps contain acid-sulfate waters and show elevated Al, Cu, Fe, Mn, Pb and Zn values. Samples collected from the Dee River bordering the mine site are less acidic, with lower concentrations of dissolved metals that gradually attenuate downstream from the mine. Concentrated acid mine waters has lead to formation of efflorescences consisting mainly of hydrous Fe-sulfates. The results of the ongoing isotope analyses on water samples show distinctive grouping of the data. The range of the sulfur isotope values for dissolved sulfate in samples from the open pit and sumps (d34S = 2.1 to 3.0 per mil) are similar to those of sulfides in the Main Pipe mineralisation (d34S = - 0.2 to 2.8 per mil). The lack of fractionation between sulfides and sulfate indicates that intermediate oxidation states of sulfur are not significant and makes this technique a useful tracer to identify the sources of sulfate. The Dee River samples, on the other hand, have heavier sulfur isotopes (d34S = 2.8 to 5.0 per mil). These samples may contain dissolved sulfate from æinternal sourcesÆ in the river basin, show local bacterial reduction or indicate a simple mixing trend. Further isotope analyses including oxygen isotopes of dissolved sulfates will enhance the interpretations.

Jan 1, 2003

By R M. Smart, A T. Harrison

Backfill systems using unconventional cementitious binders have been successfully used in relatively deep and hard rock tabular mines for longwall, scattered stoping and shaft pillar removals. Two unconventional cementitious systems are discussed: A ground granulated blast furnace slag (GGBS) with an activator containing lime. This has been used with a total tailings æstableÆ slurry at a relatively low dosage of less than seven per cent, by mass, based on dry solids. The room and pillar stopes supported with this fill were up to 20 m high and the tailings were relatively high in pyrite. A GGBS binder plus a silicate based activator and gelling agent that virtually eliminated all water drainage (and hence post filling shrinkage). The system used a slurry, but the addition of the activator created a final placed product that had the behaviour of a paste. The system has been successfully used for almost ten years in the following applications: stoping widths (mining heights) above 1.6 m; and shaft pillar removals in seismically active areas at the end of the life of the shafts. This paper discusses the technical merits and costs of the systems and compares them to other fill systems (including true paste systems). the acceleration (normally g, 9.81m/sec2) is increased to a significantly larger (but generally unmeasured and unknown) value, as shown in Figure 1.

Jan 1, 1998

By C Li

Removal of gangue minerals from ilmenite concentrates can be accomplished by relatively low temperature roasting in controlled gas atmospheres to selectively enhance the magnetic separation characteristics of the ilmenite. At roasting temperatures below 800¦C the magnetising reactions are often not consistent with phase equilibria considerations. Metastable phases can nucleate and control the roasting products. In weathered ilmenites the phase assemblages and microstructures in the altered ilmenite grains can influence the roasting reactions. In this paper we give an overview of the phase chemistry of chemically weathered ilmenites and of metastable phases formed by low temperature roasting. We also report the results of roast experiments conducted in a neutral gas atmosphere. Major increases in magnetic properties after short roasting times at low temperatures were obtained for a range of ilmenite concentrates. For example heating a secondary ilmenite concentrate from Western Australia for 15 minutes in nitrogen at 600¦C gave an increase in the three kilogauss magnetic fraction from three to 92 wt per cent. The solid state phase changes accompanying the inert atmosphere roasts were characterised by combining elemental analyses with quantitative phase analyses of the ilmenite concentrates and their roast products. It was found that the phase reaction that is principally responsible for the increase in the magnetic properties of weathered ilmenites involves a transformation of disordered ferrous-containing pseudorutile to an ordered ilmenite-hematite solid solution containing typically ten to 35 mole per cent of the hematite component. Examples are given of the application of the inert atmosphere roast to effect separations of ilmenite from gangue minerals.

Jan 1, 2001

By K Watanabe

A relational database in which its complex contents can be navigated through a map interface (ie spatially enabling) is relatively a new concept yet attractive for geoscience fields. This concept is made possible using the new breed of geographic information system (GIS) that utilises component object model and relational database management system. Such sophisticated yet open and highly interoperable platform makes possible the integration of data management, analysis, and modeling processes into single workflow. Taking benefit of this technology trend, several initiatives emerge in geoscience to establish digital data models, such as the petroleum industry, the North America digital geologic map data model, and the ESRI geology data model. The mining industry unfortunately has not followed same paths due to the lack of data model and standards in its history. This paper presents an effort on establishing a digital data model for mining-related geoscience databases. The aim is to promote several standards by proposing a preliminary data model and demonstrating that the model is working for the mining business datasets. The case study is the island of Java, the western part of the Sunda island arc of Indonesia. Many types of datasets, such as geologic maps, topography, mineral deposits, structures, geochemical and geophysical data were dealt with and were transformed relational geologic databases of Java using the new Geodatabase geographic data model. Intelligent GIS tools were investigated for geologic applications, ranging from generic to specific purposes. Subtypes and domain were used to set up constraints, while topology rules and relationship classes were used to create links among data layers. The linear referencing system was used to model drillhole data. The current results show that the generic GIS and relational database can handle typical tasks related with mining business datasets. A preliminary data model is finally suggested.

Jan 1, 2004

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

By Ryan A, Dennis R, Dekker D, Ellis W, Sowerby B

An automated facility for non-destructive elemental analysis of mine samples has been developed and tested at Mount Isa in association with the CSIRO. The analysis is based on the prompt and delayed measurement of gamma radiation emitted by the sample during and after separate fast and thermal neutron irradiation. No sub-sampling or sample preparation is required and the analyser is operated by one person that would otherwise be splitting drill core in preparation for conventional analysis. The analyser has been calibrated to measure the following (precision in parenthesis): Ag (14 ppm), Pb (0.5 wt%), Zn (0.5 wt%), Cu (0.04 wt%), Fe (0.7 wt%), S (1.1 wt%), SiO2 (0.8 wt%), A1203 (0.07 wt%), Mn (0.05 wt%), specific gravity (0.02 g cmt). Crushed or whole drill core samples that range in size between 0.5 m and 1.8 m of equivalent BQ size drill core can be analysed at a rate of six samples per hour. If required, drill core samples can be re-packed in their original configuration for storage following analysis. Standard samples are measured every day to ensure operational stability. The analyser is controlled by a personal computer which prints the results and stores them along with the raw data on the computer hard disk. This paper reports the performance of the analyser during 1992 for routine analysis of drill core from the lead ore bodies of both Mount Isa and Hilton mines.

Jan 1, 1993

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

By Anievas JB, Sevillano AC

This paper describes the acquisition, exploration, development, initial operation and subsequent financing of the Bulawan mine by means of a listing on the Toronto Stock Exchange of a subsidiary of the parent company, Philex Mining Corporation.Located on the island of Negros in the Philippines the property is unique on at least two counts: it is a disseminated gold deposit that occurs in a region of predominantly porphyry copper mineralisation; and it is a gold deposit that is mined by a bulk method of extraction (front and block cave) instead of the normal selective mining methods.

Jan 1, 1997