Search Documents

By G S. Esterhuizen, M M. Murphy, T S. Bajpayee

The strength reduction method (SRM) has been implemented in the FLAC3D finite difference software and applied to coalmine entry support evaluations. The FLAC3D numerical models have been calibrated against instrumented field sites in varying geologies, depths and field stress conditions. The calibration between the field and model results obtained a satisfactory match for rock deformation and support response. Previous research has also developed good correlations between numerical model stability estimations using the SRM and empirically derived stability estimations using the analysis of roof bolt systems (ARBS) software and the coalmine roof rating (CMRR). The purpose of this paper is to further apply the SRM to investigate how specific geotechnical and support parameters can impact coalmine entry stability. Results from different studies demonstrate how the calibrated models were used to investigate a few of the well-known questions in both mine design and support design. For mine design the impact of strong and weak beds in the roof strata, rotating the principal stresses and weakening the floor on excavation stability is investigated. For support design the impact of support length, support spacing and adding cable bolts to the design is demonstrated. These scenarios are evaluated in developmental coalmine entries for a variety of geology and field stress conditions. Stability factors are calculated for each scenario using the SRM. The SRM allows the impact of each parameter to be quantified and allows the support system to be optimised for given geotechnical conditions.CITATION:Esterhuizen, G S, Murphy, M M and Bajpayee, T S, 2014. Analysis of geotechnical and support parameters on coalmine entry stability using the strength reduction method, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 383–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D R Quick

The Goodall gold mine is located 30 km east of Adelaide River, within the Pine Creek 1:250 000 map sheet, at 8 525 000 mN: 750 000 mE, on the AMG grid. The first gold was poured in April 1988 and the mine closed in September 1993, having produced 228 400 ounces of gold from 4.095 million tons of ore, at a head grade of 1.99 g/t. Oxide and primary ore was mined from one large open cut and low grade oxide ore from three smaller pits. The gold mineralisation was discovered in 1981 by means of a helicopter borne rock chip sampling survey, which delineated 13 discrete anomalies. Systematic grid sampling of rock chips outlined an area of 1300 m by 300 m within the 2.0 g/t contour. Over 7500 m of costeaning was used to delineate the A and B-Pod mineralised areas. Geochemical soil sampling played only a minor role in the discovery and geophysics none at all. By the end of 1984, 40 diamond drill holes had been completed and a resource of 3.63 million tonnes at 3.0 g/t calculated. In January 1985, Western Mining Corporation Ltd became a joint venture partner and funded exploration to cam a 60 per cent interest. Additional drilling led to a feasibility study in 1987, based on a Measured and Indicated resource of 4.25 million tonnes at a grade of 2.35 g/t. The host rocks are quartzo-feldspathic wacke and interbedded phyllitic siltstone, of the Proterozoic Burrell Creek formation. The main zone of gold mineralisation, A-Pod, occurs in a sub-vertical vein array, up to 50 m wide and 800 m in length, of quartz and sulphide veins (5-20 mm wide), It is parallel to and on the east limb of an upright, north plunging anticline. Five types of veining have been recognised, with the bulk of the gold mineralisation associated with quartz-pyrite-arsenopyrite and chlorite-quartz-pyrite veins. The gold occurs as particles, from 1-20 micron, as inclusions and along fractures in pyrite and arsenopyrite and to a limited extent in chlorite. The mineralisation is epigenetic and structurally controlled by fractures developed during an earlier folding event. The gold is assumed to have been derived from the underlying sediments of the Koolpin Formation by hydrothermal fluids emanating from the deep seated northern margin of the Cullen Batholith. Precipitation of gold may have been controlled by variations in temperature and pressure.

Jan 1, 1994

New Celebration Gold Mine is located 35 km SE of Kalgoorlie, Western Australia, in the Archaean Kalgoorlie-St Ives Greenstone belt. The leases total 119 sq kms and arepart of a joint venture between Newmont Australia Ltd (as manager) and Mt Martin Gold Mines N.L. Mining commenced in August, 1986 and is now producing over 115,000 ounces of gold per annum. A variety of gold mineralisation styles with a total resource of 23.5 million tonnes at 2.19g/t are associated with shear zones at New Celebration. Gold production is co-ordinated from 7 open pits with others planned to com- mence soon. A large scale underground trial mining operation has com- menced with a decline on the hanging wall of the main producing orebody, Hampton Boulder. Millfeed produced is classified on the stockpile according to grade and metallurgical performance and blended tomaximise throughput while main- taining grade through a CIL treatment plant currently operating at 1.7 million tonnes per year.

Jan 1, 1991

By A I M Ritchie

The pyrite oxidation rate is a process central to both the performance of bio-oxidation heaps, used in the pre-treatment of some refractory gold ores, and to the levels of pollution in acid rock drainage (ARD) from pyritic waste rock dumps. A goal in bio-oxidation heaps is to achieve high oxidation rates in the heap as a whole. In comparison, one way to mitigate the environment impact of ARD, is to reduce the overall oxidation rate in the waste rock dump since pyrite oxidation is the primary pollutant generation process. In both bio-oxidation heaps and waste rock dumps the overall oxidation rate of the pyritic material (the intrinsic oxidation rate) at these sites. Much research has been conducted over the last 40 years or so on the oxidation rate of pyritic material with particular emphasis on the catalytic role played by bacteria. More recently mathematical models and field measurements have clarified the extent to which oxygen transport rates are rate limiting, what the dominant oxygen transport mechanisms are and the physical properties of the heaps which have most impact on these transport rates and on the overall oxidation rate. How the performance of bio-oxidation heaps can be optimised and how the pollution load in drainage from waste rock dumps depends on gas transport mechanisms is briefly reviewed. The sensitive of the overall oxidation rate in bio-oxidation heaps and waste rock dumps to details of the intrinsic oxidation rate is quantified.

Jan 1, 1994

By M Olsen

"Segregation of conveyor roadways is a ventilation practice that is being increasingly applied in Australia. It is largely driven by the legislated requirements in Queensland pertaining to separation of escapeways from the mine. This legal requirement was based on a recommendation from the Moura No. 2 WardenÆs Inquiry (Windridge, 1996) into the mine disaster that claimed 11 lives. The report recommended: ... the introduction of a requirement for all underground mines to have one intake airway that is completely segregated from other parallel intake airways so as to provide two separate means of egress from the mine via an intake airway.This recommendation seeks to assist mine workers in escape from a mine after a fire by providing them with an airway that is free from smoke or contaminants.The concept of an airway being æcompletely segregatedÆ is an ideal that is challenging to implement in practice when considering the effect of leakage. The practice of belt segregation is concerned with the potential for fires in the belt roadway although there are numerous other potential fire sources in underground coal mines. A review of segregation practices has been conducted applying ventilation engineering principles. Four different scenarios have been analysed with regard to the effectiveness of the segregation stoppings in preventing potential fire contaminants migrating to other parts of the mine. The results show that in some cases the benefits of segregation to a person evacuating a mine in the event of a fire range from beneficial to detrimental. This is influenced by many factors including the location of that individual in that particular mine. There is room for improvement in the design and implementation of escapeways in underground coal mines. Escapeways need to be planned and designated with regard to the potential sources of fire, pressure differentials between escapeways and the operational practicalities of maintaining the pressure differential between them.CITATION:Olsen, M, 2013. Belt road segregation and escapeways - Compliance or risk management?, in Proceedings The Australian Mine Ventilation Conference, pp 311-318 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 1, 2013

Mining is still a significant economic activity within the Hauraki District. The Martha project is particularly significant. Estimates are that in the order of 850 direct and indirect jobs are derived as a consequence of the Martha project within the Waikato Region. The Resource Management Act 1991 (RMA) is New Zealand's primary piece of environmental legislation. It sets out to provide the framework for the control of the use, development and protection of almost all physical and natural resources. Minerals are excluded from the sustainability requirements of the legislation but as mining invariably involves the use of land, all the other elements of RMA apply. The Council's role in dealing with mining changed with the introduction of RMA. It became responsible for administration of those matters that fell within the functions set out in section 31 of the RMA in respect to existing authorisations. Mineral development needed to be considered in the development of the District Plan that the Council is required to prepare. Implementation of the Act has been a challenge for not only local government but for many industries and resource users since it came into force in 1991. There have been, and are, differing views on both the way it is administered and its intent. The Hauraki District Council has been at the forefront of some of the challenges that are a consequence of the Act. Its reactions to these challenges have been consistent. It treats mining in the same why it treats any other industry. At times this approach has not been understood and without challenge from sections of the community.

Jan 1, 2000

By Casley G. E, Pritchard J

A single slurry fed fluosolids roaster was chosen to replace six multiple hearth roasters in the Copper Smelter at Mount Isa as part of the overall program to increase production from 100 000 to 155 000 tonnes blister copper per annum. The paper describes factors influencing the choice of the unit, problems encountered during the commissioning and details of the present roaster operation.

Jan 1, 1974

By Walton S, Wheeler D. J, Sargent D. M, Ting L. Y

Goonyella-Riverside mine is an open cut coal mine in Central Queensland. One component of the mining operations at this site is an uncompacted spoil dump some 50 m above the natural ground surface and over 300 ha in extent formed as a result of bucket wheel excavator operations. Plateau area slopes are 0.5¦ to 1.5¦ with irregular outer dump slopes of 9.5¦ - 17¦Investigation was undertaken and a series of trials planned to assess the suitability of a variety of stabilisation proposals to meet the client's requirements and to conform with Department of Resource Industrystabilisation guidelines.

Jan 1, 1992

By Blair J. R, Barrett J. R

In many underground mining applications where-dry fill is used, only a token acknowl- edgement of the fill properties is given. It is the aim of this paper to induce mining engineers to consider dry fill as an engineer- ing material rather than a mass to place in unwanted voids. Dry fill is generally cheap, inert and readily available, but it can still contribute to mining performance. In particular, the choice of the dry fill becomes more critical as stope sizes increase, controlled choked draws are used or pillar recovery introduced. Selection must be initiated from an evaluation of the role of the fill in the mining operation. In most cases the fill must be chosen before quarrying begins and an investigation must be made of available sources and appropriate quarrying methods. Some of the properties of fill are described together with evaluation techniques. A com- parison of placement conditions is limited by the complexities of material flow and degrada- tion: However, field and model tests can aid interpretation in these cases. Examples are given of aspects of dry fill selection and their incorporation in mining design.

Jan 1, 1973

The operation of cyclones and cylinders is briefly described and com- pared, and a number of recent applications in mineral, gold and coal plants discussed. The capacity of an existing pump and cyclone in a circuit can be sig- nificantly increased by retrofitting a cylinder in series to predensify the cyclone feed. The cyclone overflow product size can also be adjusted and controlled using a variable aperture valve between the cylinder and the cyclone. This predensifier-cyclone system has been used at plant scale to con- trol the pulp density of the feed to cyanidation in gold plants, to size flotation feeds before split conditioning and to deslime and classify in gravity plants. Application in a typical regrind circuit is considered. Cylinders and cyclones also have numerous applications in water management systems, e.g., degritting mine and plant waters to protect pumps, sprays and other equipment. Screen undersize and flotation con- centrate dewatering circuits are described to illustrate how suitable stream recycles can reduce water consumption, optimize fresh water use and improve efficiency.

Jan 1, 1988

By Massacci P

A review has been made of the studies focusing on methods for the description of grain -size distribution after breakage and, separa- tely, of the degree of liberation of the miner- al species making up the various grain-size classes of comminution products. The purpose of the study has been to de- velop an overall model of the phenomenon which, owing to the very effect of comminution, leads to the formation of grains that are generally of mixed composition. A calculation procedure has thus been de- veloped for the liberation function taken as the assessment of the distribution of mix com- ponents in the products obtained after a commi- nution process. The aim is to identify a func- tion which may, to a certain extent, simulate the variation of the grade-recovery function of an ore in relation to its degree of comminu- tion. The numerical model thus obtained has been tested out on results obtained experimentally.

Jan 1, 1986

By Thomson I. R R, Friday R. G, Palmer W. T

The paper introduces the problems encountered in designing open stopes and briefly examines the factors that determine the final stope dimensions achieved after mining is completed. A case study is presented where monitoring of a stope was considered necessary due to the expected formation of a highly stressed crown pillar above the stope. The influence, on the mining approach adopted, of a yielding crown pillar is discussed. Monitoring and numerical modelling were used to develop an understanding of the behaviour of the particular stope as mining progressed. A comparison between the measured displacements and the numerical predictions at an interim stage of mining was carried out to assist in choosing the final sequences involved in completing the stope.

Jan 1, 1981

By Abishev D. N, Balakirev V. F, Davydov G. I

The problem of recovery of cobalt products from poorly oxidised nickel ores (Kempirsaisk deposit) and pyrite concentrates with a low content of cobalt (Sokolovsk-Sarbaisky deposit) has not been solved to the present time in Kazakstan. The balance reserves of nickel ore of the Kempirsaisky deposit make up more than 35 million tons with a nickel content of 1.13 per cent and cobalt content of 0.05 per cent; besides there are 110 millions tons of out-balance ores (Anon, 1995). In a tailing dump of Sokolovsk-Sarbaisk Mining and Productional Association more than 320 million tons of tailings of wet magnetic separation have accumulated, which contain 7.2 per cent of sulphur, 0.022 per cent of cobalt, 0.012 per cent of nickel, 0.094 per cent of copper, 0.079 per cent of zinc, 16.45 per cent of iron, and from which a high quality pyrite concentrate car) he separated through flotation, containing 48 - 50 per cent of sulphur, 44.15 per cent of iron, 0.141 per cent of cobalt, 0.07 per cent of nickel, and 0.10 per cent of copper. The well-known technological flow charts for cobalt and nickel recovery from the tailings of sulphide-magnetite ores dressing (to give pyrite concentrate) and from oxidised nickel ores, are not profitable at the existing prices for metals, but are not worthless and require significant capital investments for the realisation of their value. The flow chart `sulphate roasting - leaching - solution processing' is used widely for combined processing of cobalt-containing pyrite ores and concentrates.

Jan 1, 1996

By Ormsby W. R, Nicholson P. M

Woodcutters is a polymetallic vein-style deposit hosted by sediments of the Palacoproterozoic Whites Formation which forms part of the sedimentary sequence in the central Pine Creek Geosyncline. Past production and identified resources total over eight million tonnes at 5.5 per cent lead, 12.1 per cent zinc and 110 gA silver. The local geology is influenced by Archaean basement highs; the Rum Jungle and Waterhouse Complexes. Unconformably overlying basement are interbedded clastic and crystalline carbonate units (Batchelor Group) representing cyclic changes in the depositional environment. These exhibit onlapping features with the underlying rocks. Sediments of the overlying Frances Creek Group suggest a quiet period during subsidence and subsequent increase in water depth (the carbonaceous dolomitic shales and the interbedded dololutites of the Whites Formation) followed by proximal uplift resulting in the inundation of turbiditic flows (Acacia Gap Quartzite). All of the Palaeoproterozoic rocks show evidence of being affected by penecontemporaneous, basement circling faults with steep dips. The stress regime during the deposition of the Frances Creek Group was characterised by alternating episodes of thrusting and transpression. Periods of relaxation also occurred. The compression resulted in major NS strike-slip (transpressional) faulting, en-echelon NNE trending folds and NW-SE tensional cross faults. Thrusting produced N-S striking, steep dipping reverse faults and a possible decollement immediately above the Batchelor Group. Relaxation is evidenced by the intrusion of lamprophyre dykes and dolerite sills (Zamu Dolerite). Mineralisation at Woodcutters occurred in faults within the Whites Formation, probably synchronous with deformation and the deposition of the upper parts of the Frances Creek Group. Greenschist facies metamorphism occurred as the rocks were further buried. Several massive sulphide bodies occur at Woodcutters. A number of features influence the location and shape of these bodies. They are: ò the N-S transpressional faults and in particular associated dilation zones; ò intersection of the N-S transpressional faults with the axial plane of the NNE trending Woodcutters Anticline; ò intersection of the N-S transpressional faults with the NW-SE cross-faults; ò intersection of dololutite rich units with the NS transpressional faults where local replacement takes place; ò thickening of the lithological units in the vicinity of the anticlinal axis; and ò the anticline doubly plunging to both the north and south. The mineralisation exhibits vein-like features as well as epigenetic textures. Its boundaries are sharp, its thickness varies rapidly down dip and along strike, and no alteration halo exists though stringer veins of quartz-carbonate-pyrite ¦ sphalerite/galena occur in close proximity. A number of sulphide mineral assemblages have been recognised, each separated by periods of deformation and partially replacing the earlier assemblages. Vertically continuous zonation patterns highlight the presence of rich galena-sphalerite-silver in zones of maximum dilation and pyrite-arsenopyrite-gold concentrated at the along strike peripheries. The genetic model proposed has the mineralisation occurring whilst the transpressional regime was active. It was deposited from the same fluid that elsewhere in the Geosyncline formed the stratiform deposits higher in the sedimentary pile. Hydrocarbons sourced from the organic-rich Whites

Jan 1, 1994

By Frfas C, Parrilla F, Regife J. M

A project to develop the Zinclor electrowinning cell to industrial size is being conducted at Tecnicas Reunidas' Research and Development Centre with Spanish Ministry of Industry support. This project is the final development phase in zinc electrowinning from a chloride medium, the highest ZINCLOR technology development level prior to the industrial scale having already been reached. This paper covers the outcomes and conclusions corresponding to project Phases 1 and 2: Process Selection and Industrial Electrodes (1 m2) design and testing. The most important achievement reached is that there are presently available industrial cathodes and anodes for the Zinclor diaphragm cell giving an optimum response for zinc chloride electrowinning with unit power consumptions between 2.65 and 2.80 kWh/kg Zn, depending on the diaphragm type. Standard electrolysis conditions were: 65 g/L ZnC12, 3 g/L HCl, 160 g/L NaCl, 350 g/t Zn arabig gum as the addition agent, 36¦C, and 400 A/m2 current density. The selection of electrodes, diaphragms and organic additives for the industrial scale tests have been optimised. The complete electrowinning cell development, with electrodes having an active area of I m2, enables the evaluation of Zinclor Technology application for industrial processes.

Jan 1, 1993

The key issue which determines the use of imaging for explosives and mining research is the question - `What information will I gain by using imaging technology?' This paper will address that question from the point of view of a researcher and cameraman working in industrial imaging and photography. The paper will establish a common set of reference standards for high speed imaging and photography which researchers can apply when deciding which type of imaging technology is appropriate. It will present an overview of current image analysis technologies and practices in use across a range of appropriate scientific fields and draw lines of commonality of approach between these fields and the field of explosives and mining analysis and research. Further to this, the paper will examine the different technologies from an image quality reference point, ease of operation, cost, and reliability parameters. Finally this paper will present an argument for the hybridisation of established and new technologies which could provide a more beneficial approach to the use of imaging as a tool of research and analysis in the explosives and mining industries. This will include a novel approach to high speed filming and analysis in the field which should deliver high quality images in a time frame which is more appropriate to urgent action and solutions.

Jan 1, 1995

One of the earliest and continuing challenges in driving sustainable development in large scale resource industry projects is around the issue of assessment û how do you measure the sustainability of a mineral operation? One of the key road blocks when confronted with this challenge is the temptation of technical folks to reach for a definition of sustainability or sustainable development. But definitions, by definition, have boundaries and limitations that serve to constrain thinking û they limit the thinking of what we can achieve with sustainability (it also acts as a barrier that constrains innovation). Rather than seeking definitions, better understanding of the core perspectives around sustainability and their application to the minerals industry provides a much more powerful platform from which to conduct assessments. But it is only when these perspectives are combined with the right framework and supporting techniques that the complex becomes doable. With the support of the perspectives and the framework, various assessment and measurement methodologies can be used; the challenge is communicating to stakeholders the sustainability character of the project in ways that are meaningful and to which people can connect. Assessment is not about finding the best or most accurate methods that fulfil strictly academic and possibly abstract requirements. The challenge is to help people understand what the impacts are, and what the value contributions will be, in a format and language that make sense in their world-view.

Jan 1, 2009

By E Villaescusa, C Drover, I Onederra

Development face destress blasting is a construction technique in deep mining, which aims to prevent, reduce the frequency, or manipulate the timing of violent, stress-driven rock mass instability at the face. This paper presents a destress blasting design concept that was optimised for the specific rock mass conditions of a deep mine using the Hybrid Stress Blasting Model (HSBM) software. The design was then implemented in an area of the mine where stress-driven instability of the face regularly occurred during development. An adjacent tunnel was constructed in parallel without destressing, within the same rock mass conditions, as a control. The rock mass response to each excavation was quantitatively compared using high-resolution local seismic monitoring. Visual observations of the fractures created by destress blasting were also made. The analysis indicated that destressing reduced both seismicity and the rock mass stiffness ahead of the face. This was inferred from the spatial broadening of the development seismogenic zone and the typically significant reduction in the spatial density of seismic events. Seismic source mechanism analysis also indicated that destress blasting generated a much wider variety of failure modes than conventional blasting. Most seismic source mechanisms following destressing were associated with natural joint structures. A relatively small portion were consistent with newly created blast-induced fractures. The greater diversity of rock mass failure modes associated with destressing implied a lower potential for stain-energy accumulation within the rock mass at the face, and thus a lower risk of hazardous instability. Observations of visible rock fracturing indicated that the major principal stress influenced the damage intensity on natural geological structures within the destressed zone, and that numerical predictions of radial fracturing limits made by HSBM analysis were realistic representations of the real blasting performance.

Nov 29, 2022

By N Gupta, R Trivedi, S Bhandari

Managing blasting operations in four mines surrounded by villages is a challenging task. This study aims to compare the blast-induced flyrock as observed in opencast mines by predicting flyrock distance using a soft computing approach known as an adaptive neuro-fuzzy inference system (ANFIS) and Flyrock Predictor software based on empirical studies. Blast design and geotechnical variables such as linear charge concentration, burden, stemming length, specific charge, unconfined compressive strength and rock quality designation were selected as independent variables, while flyrock distance was used as a dependent variable. Out of 120 blasts, data from 100 blasts was used to train and test the ANFIS model. Flyrock distance for the remaining 20 blasts was used to evaluate the model. Flyrock distance has also been predicted using Flyrock Predictor software based on an empirical approach using the same data sets as those used for ANFIS. Performance indices like root mean square error (RMSE), mean absolute error and coefficient of determination (R2) were evaluated to compare the reliability of ANFIS and Flyrock Predictor quantitatively. ANFIS was found to be a better predictive tool, with 1.75 m RMSE and 0.966 R2 compared to Flyrock Predictor, which returned RMSE and R2 values of 2.48 m and 0.932 respectively.CITATION:Trivedi, R, Singh, T N, Gupta, N and Bhandari, S, 2015. Soft computing approach to predict blast-induced flyrock, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 455–462 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T G. Vizcarra, B Wong

Optimisation projects are regularly undertaken without knowing the root cause of an issue. It is all well and good to trial a multitude of flotation reagents, change the operating characteristics of your flotation cells, or add more media into your ball mills, but time and again, root cause analysis traces issues back to the performance of hydrocyclones. In JKTech's experience, hydrocyclones are poorly operated and maintained (in both primary grinding and regrind circuits), exacerbating issues that many operations commonly experience.Recent case studies are presented where JKTech has been engaged to improve the process only to discover that the hydrocyclones were the main issue. At one operation it was found that the hydrocyclone feed density gauge was reading significantly lower to the actual density. Following re-calibration of the gauge, and with further improvement of cyclone operational and design parameters using JKSimMet, a significantly sharper efficiency curve was achieved. This resulted in improvements to downstream recoveries while alleviating pumping capacities that were previously constrained by fines and water caught up in recirculating loads.Several other case studies are presented which may seem to be relatively basic, but many basics seem to be getting lost in the day-to-day responsibilities of the modern plant metallurgist. Simple fixes to hydrocyclones can result in significant production increases, but more focus is needed in monitoring these to sustain the benefits.CITATION:Wong, B and Vizcarra, T G, 2018. What category cyclone is devastating your plant?, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 665–673 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018