Search Documents

The Channel Tunnel is an outstanding example of an undersea tunnel and its design illustrates most of the unique features of this type of tunnel. The marine site investigation was partic- ularly vulnerable to adverse weather conditions. To minimise this interference the time the drilling vessel was required to remain on station was kept to a minimum by expediting the drilling and the insitu tests as far as was practicable. To avoid additional unforeseen costs the contract documents were framed to take particular account of marine practice. The limited access at the coast line meant that for economy, maximum tunnel advance rates had to be attained. Ground excavation, handling and disposal methods and the provision of the lining were optimised and equipment specified in detail to ensure that no one com- ponent was delayed by a lack of capacity or mechanical failure in any other.

Jan 1, 1976

By M D. Melville, B C. T Macdonald, T D. W

The surface waters in regions with acid sulfate soils (ASS) can contain high concentrations of acidity and dissolved metals. These soils cause problems for agriculture, construction and development. The water can be neutralised through many techniques, however a technique that is low in maintenance and low in cost is most desirable. Due to the vast spread of ASS along AustraliaÆs coastline an expensive and high maintenance solution would not be cost-effective. In this study, a passive treatment system that has been used to neutralise acid rock drainage has been applied to treat ASS water. This system is commonly referred to as an oxic limestone drain (OLD) or an anoxic limestone drain (ALD) depending on the waters dissolved oxygen concentration. The system that has been developed for ASS has a similar closed system to the OLD or ALD, that traps the carbon dioxide which forms when limestone reacts with acidic water. It has been called a closed tank reactor (CTR) and is constructed by placing limestone into an airtight tank. A common problem that will occur when acidic water with a high concentration of dissolved metals reacts with limestone is the formation of metal oxy-hydroxide precipitates. These precipitates can coat or armour the limestone and reduce its reactivity. To minimise the accumulation of precipitates in the CTR, perforated subdrains have been installed. It is anticipated that high water pressure and flow through the subdrains will remove some precipitates. A sump has also been installed at the base of the tank to collect precipitates that settle under gravity. The CTR has been tested for 70 days at a sugar cane farm located at McLeods Creek, NSW. Within this time the sump and subdrains have been used to flush the system. An orange solution was produced during flushing and it is believed to contain iron and aluminium precipitates. The initial performance of the CTR raised pH by at least one unit. Almost all dissolved aluminium was removed and more than half the dissolved iron. The total titratable acidity ranged from 17 - 92 mg/L CaCO3 in the initial month of monitoring. After passing through the CTR the acidity was reduced to zero. The performance of the CTR during the last few days of monitoring decreased. This is believed to be due to a pulse of water with higher acidity and dissolved metal content that lasted a week. In this pulse, the acidity reached 307 mg/L CaCO3 and the total dissolved aluminium reached a maximum of 24 mg/L. Higher concentrations of dissolved metals may have been the cause for lower performance due to increased precipitation and coating on the limestone.

Jan 1, 2003

By Rogis J

The basic parameters causing outbursts are rock pressure, gas characteristics and the physico-mechanical properties of the coal. The three sets of factors are to some degree interdependent. At Collinsville, the gas characteristics coupled with the physico-mechanical properties of the coal appear to be the major factors contributing to outbursts. The relative importance of rock pressure is uncertain. The following geological parameters appear to be necessary before outbursts can occur. 1. A coal rank greater than 1.2% vitrinite reflectance. 2. Thrust faults with throws greater than 3.Om or strike- slip faults with coal gouge wider than 0.3m. 3. Seam gas emission values greater than 1.1 cm3 /g. Igneous intrusions are the likely source of the carbon dioxide seam gas. Outbursts have occurred at depths ranging from 215m to 265m. They occur at these relatively shallow depths due to: 1. the high rank of coal at the present topographic surface and the high coalification gradient; 2. the relatively high degree of tectonic deformation of the strata; 3. the seam gas characteristics; and 4. the extent of igneous intrusions.

Jan 1, 1980

By H Kim, M J. Sun

Global steel companies are actively combating climate change by reducing carbon emissions. Traditional steel production, using the blast furnace (BF) – basic oxygen furnace (BOF) process, heavily depends on coal and emits substantial CO2. To mitigate this, companies are transitioning to the more eco-friendly DRP (direct reduction plant) – EAF (electric arc furnace) process, which lowers CO2 emissions. This study quantitatively evaluates the impact of increased hydrogen consumption on the carbon footprint of product (CFP) through an analysis of direct reduction process heat and mass balances. The study prioritises a comprehensive material balance based on mass conservation principles. The heat balance is calculated using differences in enthalpy through state energy properties, avoiding heat consumption. Validation using operational data from Hyundai Steel Dangjin works’ blast furnaces shows close alignment between calculated results and actual data, with less than 1 per cent error. This methodology facilitates a detailed analysis of the direct reduction process, offering insights into its feasibility and efficiency. Analysis of the operational impact by increasing the hydrogen ratio demonstrates reduced CO2 emissions and increased heat requirements due to the endothermic nature of hydrogen reduction, in contrast to the exothermic CO reduction. Possible solutions include raising reducing gas temperature or enhancing flow rate. The study effectively utilises designed heat and mass balances to assess material quantities and thermal balance under different operational conditions. It lays the foundation for the initial direct reduction process design, aiding in deriving and optimising operational parameters. Additionally, it provides valuable insights into the challenges of increased hydrogen, contributing to the production of greener steel by addressing these issues.

Aug 21, 2024

By M Gabbitus, B Young, T Lukins, M Slater

This paper details the implementation of a new type of grade control system at the Black Star open cut mine in Mount Isa, Queensland. It explores the site requirements for grade control, what as previously in place and what the site required moving forward. It also details some of the features of the system installed and why it was chosen over other grade control systems available. Black Star open cut mine has been in operation since late 2004, and was developed to extract the surface extents of the Ag-Pb-Zn mineralisation previously mined in the Isa Lead Mine. Black Star is currently mining seven distinct orebodies in and around active void hazard zones and hence, its grade control requirements are very detailed and complex. The implementation of a new system to manage the model update and block out processes was, therefore, of critical importance to the site and required a detailed understanding of the requirements of the entire mining team from drilling through to geology, survey and production. Having previously run the grade control process using site specific æblack boxÆ scripts and macros, Black Star needed to implement a more open, auditable and flexible system, which allowed the geologists to control the process and make strategic changes as the situation demanded. MineSightÆs Axis Grade Control, with its flexible, generic framework for managing the process, met these demands. Being an out of the box solution that requires minimal setup and training was also a key factor in the decision to use it.CITATION:Lukins, T, Slater, M, Gabbitus, M and Young, B, 2012. The introduction of axis at Black Star Open Cut, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 71-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

This paper describes the technical development of the Newman beneficiation plant over its 23 years of operation and how this development relates to the mine ore reserves of high-grade and low-grade ore. It also discusses the importance of the beneficiation product grades in the overall blending of shippable products from a range of mines to optimise overall ore resource utilisation. Also discussed is the importance of the ore reserve reconciliations in resource utilisation. Data is provided on the capacity and quality improvement results of the plant upgrade, carried out in 1999. This shows how the original capacity upgrade targets have been exceeded and the additional quality benefits that have been obtained from this capacity.

Jan 1, 2002

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By S Fidler

Underground coal gasification (UCG) is a process by which coal is converted in situ to a combustible gas that can be used as a fuel or chemical feedstock. The process has been used in commercial-size projects in the former Soviet Union for more than 40 years, while significant national research programs have been undertaken in the United States and Western Europe. The Chinchilla UCG project is located at a site southeast of Chinchilla in Queensland. The UCG operation commenced in December 1999. A controlled shutdown of the process was initiated in January 2002 and successfully completed in April 2003. The process is currently under conservation and ready for restoration of gas production for commercial use in the near future. Groundwater plays an important role in the gas formation process during UCG. Most of the process water required for chemical reactions is usually derived from the coal seam itself and from surrounding aquifers. If insufficient water is available for chemical reactions the UCG gas will contain reduced concentrations of combustible components, and conversely, excessive water influx into the process area would cool down the reactor and thus limit the energy available for gas production reactions. Because of the importance of groundwater in the gasification reactions, and the potential to contaminate groundwater if the process is not correctly controlled, it is essential to predict and to control the groundwater influx into underground gasifiers during and after underground gasification. Control of groundwater requires a thorough understanding of hydrogeological conditions in the vicinity of the gasifier in order to be able to predict inflow rates, and constant monitoring throughout the process of water production rates and groundwater pressure in the coal seam and adjacent aquifers. Hydrogeological testing and groundwater monitoring in the vicinity of the UCG operation commenced six months in advance of its initiation. Monitoring of groundwater pressures in the vicinity of the gasifier have also been undertaken using vibrating wire piezometers installed in the coal seam at varying distances from the gasifier. This paper presents the results of the hydrogeological testing and groundwater quality monitoring carried out at the site, which show that it is possible to operate a UCG process without uncontrolled impacts on groundwater.

Jan 1, 2003

By D Hunter

A production information management system (PIMS) was recently implemented at Queensland NickelÆs Yabulu Refinery. Although a strong business case was developed to justify the significant investment in PIMS some potential beneficiaries remained sceptical of the anticipated benefits. The decision to install PIMS was justified as the on-line availability of continuous production data enabled the optimisation of some crucial operations resulting in significant cost savings, improved throughput and final product quality. Furthermore the rapid access to extended historical data has allowed the cause of repeated failure of equipment to be determined. The investment is expected to pay for itself within two years and has already contributed towards significant savings. This paper focuses on some of the diverse production improvements gained and compares the anticipated benefits in the business case to those achieved. A brief outline of the phased implementation of the OSIsoft PI data historian and complementary client software at Yabulu is included, along with details of the lessons learned.

Jan 1, 2003

By R Blin, R Walde, R Belli, D Inaudi

A fiber optic distributed sensing system allows the monitoring of parameters useful to determine the short- and long-term behaviour of the structure in response to the external actions, including, eg seismic activities as well as long-term phenomena such as seepage, tunneling, sinkholes, and other geo-structural movements. Monitoring of large retaining structures with such a system provides direct strain/deformation and temperature measurements on the broad interior area with an arrangement of several sensing cable lines, enabling early detection, localisation and sizing of subsurface damages. Measurements are provided every meter along the entire sensing cable, this is particularly important in such cases where the location of defects and damages cannot be predicted. Fiber optic distributed sensing cables are generally available for retrofit installation inside the dam structure using trenches on the downstream face or laid during construction below the geomembrane liner within the bedding sand layer. Mapping the cable route enables exact correlation between a linear coordinate on the cable length and a position in the dam. Cable installation is envisaged to be carried out during further raising of the embankment; additional cable sections are plugged to the previously installed cables and measured with the existing measurement system, requiring only an update of the mapping. The measurement system is placed remotely from the sensing area since a section of sensing cable can be used to link to the sensing area at the storage facility several kilometers away. The system is available for on-line, 24/7 real-time operational data management. Such fiber optic distributed sensing systems allow storage facilities to be monitored with long, accurate, continuous and precise data for geotechnical diagnostic purposes. This contribution will introduce the principles, benefits, and limitations of this technology.

Jul 1, 2021

This paper describes a detailed geostatistical study of producing copper orebodies at Mount Isa Mines Limited in Queensland, Australia. As a result of this work, kriging has been adopted for grade estimation for final stope design at Isa Mine. Extensive variogram and back analysis studies indicate that one relative variogram model can be used to give optimal kriged grade estimates from production sampling throughout the 100 million tonne copper orebody complex. The kriging method replaces a computer technique used at [sa Mine based on inverse distance weighting using parameters chosen from experience.Comparative stope designs based on 10 million tonnes of ore indicate a 16% increase in minable ore tonnage at a grade well above the cut-off, as a result of the geostatistical work.Although this paper is written as a practical description with simple explanations of geostatistical concepts, the theory and use of relative variograms has been expanded. A possible link is suggested between relative variograms and first order kinetics of natural mineral concentration processes.

Jan 1, 1982

The Comstock Lode, a world-class precious metal vein district near Virginia City in western Nevada, U.S.A. (Fig. 1), produced 8.3 million ounces (0.28 X 106 kg) of gold and 193 million ounces (6.56 X 106 kg) of silver during the period 1859 to present (Bonham and Papke, 1969). More than 95% of production was from the Comstock fault, while the adjacent Silver City, Occidental and Flowery vein systems produced about $10 million (U.S.). Within the Comstock fault high-grade ore bodies, or bonanzas, were distributed over 2.3 miles (3.8 km) along strike and persisted to >3000 feet (>900 m) below the surface (Fig. 2). Bonanzas consisted of as much as 1.4 million tons (1.3 million tonnes) of ore grading up to 1.9 oz./ton (65 gm/ton) Au and 30 oz./ton (1020 gm/ton) Ag (Table 1). Some bonanzas occurred in the main Comstock fault plane while others, including the highest grade bonanzas, formed in hangingwall frac- tures. After 1880 most ore consisted of lower-grade vein material surrounding mined- out bonanzas and large volumes of mineralized vein and wall rock in the Comstock hanging- wall that were mined from open cuts. Deep mining was hindered by large quantities of hot water and bad ground which ultimately defined the limits of underground production. The widths and richness of Comstock bonanzas strongly influenced U.S. mining law, milling and underground mining methods, and securi- ties regulations that are in practice today. Within the district Mesozoic metasedimentary rocks, metavolcanic rocks, and granitic in- trusions are overlain by Miocene volcanic rocks (Thompson and White, 1964). Veins cut all lithologies. Miocene volcanic rocks and their K-Ar ages (Vikre, McKee and Silberman, 1987) include Santiago Canyon rhyolite (22

Jan 1, 1987

By K Evtiminova, G Jobson, M Nolte, S Meik

Chelopech Mining EAD (CMEAD) is a wholly owned subsidiary of Dundee Precious Metals Inc (DPM) and operates the Chelopech underground mine and processing facility located in Bulgaria. The final product sold is a flotation concentrate containing copper minerals with associated gold and silver. The increase in production from 0.6 to 1.0 Mt/a by 2009 occurred with the original (1975) secondary/tertiary crushing, and primary/secondary ball mill circuits. As part of the mine/mill upgrade project to 2.0 Mt/a, a new single stage semi-autogenous (SAG) mill and ancillary equipment was installed, replacing the original circuits, with commissioning occurring during the first half of 2011. Aspects of the design, commissioning and operation of the new comminution facility are the subjects of this paper.An extensive program of comminution characterisation test work was completed in 2004/2005, which indicated moderate hardness and competency characteristics. The characteristics were considered suitable for a range of comminution approaches which were assessed with respect to power requirements and capital and operating costs. Retention of the existing primary crushing facility, and installation of a new single stage SAG mill located within the existing mill building, was selected as the design for the expansion.An extended ramp-up schedule for the overall concentrator upgrade turned out to be necessary as the comminution and flotation circuits were completed prior to several downstream unit processes (concentrate filtration and tailings thickening), which were required to reach the design mill feed throughput rate on a sustainable basis. This resulted in the opportunity to gradually increase the SAG mill ball charge as necessary, to obtain the throughput corresponding to the various downstream processing constraints.A relatively fine cyclone overflow stream particle size distribution is a feature of the Chelopech comminution circuit that has not been fully overcome with increasing ball charge conditions. However, design throughput has been met even under the finer product size conditions and will be consistently achieved following the commissioning of two further process improvement projects scheduled for late 2012.CITATION:Jobson, G, Nolte, M, Evtiminova, K and Meik, S, 2012. The modernisation and upgrade of concentrator operations at the Chelopech Mine, Bulgaria - Design, installation and operation of the 250 tonnes per hour comminution circuit, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 325-332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By G R. Hancock, W D. D P Welivitiya

is placed in a waste rock dump, which is usually later reshaped to be erosionally stable, initiate and sustain vegetation and ultimately integrate with the surrounding undisturbed landscape. However, it is unclear how this exhumed material will weather and evolve for most sites. Also, there is a lack of data on the weathering of post-mining materials. If weathering is better understood, then there is the potential to improve rehabilitation outcomes. To improve predictions of the evolution of soil properties and weathering-limited erosion, estimating the rate at which fine, transportable material is produced from the weathering of larger, non-transportable particles and the resultant fragment size distribution and how that distribution evolves over time is necessary. This study examines the weathering process for four different coalmine waste rock materials for a Bowen Basin, Queensland site. Materials obtained from various areas of the coalmine were subjected to cyclic wetting and drying and heating and cooling. Particle size distribution and other material properties were explored after each experimental cycle to ascertain how the material changes during the experimental cycles. The particle size distribution data of wet and dry cycles were used as input data in a numerical weathering model to explore the dynamics of the weathering process for each material sample. A Monte Carlo framework was employed to assess the geometry of the weathering products, weathering rate and the number of daughter particles produced within a weathering cycle. Then the SSSPAM Landscape Evolution Model was used to evaluate the influence of weathering on erosion and landscape evolution of a post mining landform. SSSPAM simulations with: (i) active weathering and (ii) without weathering were run for each material. The erosion rate and the overall landform structure were then compared between weathering and non-weathering simulations.

Aug 2, 2023

By L A. Martinez Tipe, J McKibben, S Barry

"Metal prices are central to a mineral investment decision and have a profound impact on the financial performance of companies in the mining industry. At its most basic level, metal prices are influenced by the disequilibrium between international metal volume supply and demand. That is, the commodity price is a regulator that equates international metal supply and demand where inventories act as a buffer between the emergence of this disequilibrium and its dissolution through a price change.From this viewpoint, mining companies are required to forecast metal and bulk commodity prices when evaluating minerals projects through discounted cash flow (DCF) analysis. While supply-demand models are instructive, many companies use historical prices, spot prices, futures/forward pricing and consensus opinion (or a combination of all of these) to develop price forecasts.This paper discusses the definition, fundamentals and differences between futures/forward and consensus pricing and the appropriateness of each in a DCF model for mine project economic evaluation.Our results demonstrate that great care is required when using either futures/forward or consensus pricing and that the decision to use one rather than the other requires consideration of other important elements in the DCF model (ie the risk-adjusted discount rate).CITATION:Martinez Tipe, L A, McKibben, J and Barry, S, 2016. Metal prices and the differences between forward and consensus pricing – which one is better for use in a discounted cash flow model?, in Proceedings Project Evaluation 2016, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By D Guibal, J Vann, M Harley

Many sample value distributions are highly skewed and present variograms with high relative nugget effects and/or short-range structures. In consequence, significant deskewing of the histogram and variance reduction occurs when transforming between sample and block support, where blocks are of significantly larger volume than samples. When making estimates in the mining industry we usually wish to estimate on the basis of block support rather than sample support. The selective mining unit (SMU) refers to the minimum support upon which ore/waste allocation decisions can realistically and practically be made. The SMU is usually significantly smaller than the sampling grid dimensions, in particular at exploration/feasibility stages. In a non-linear estimate, for each large block (by convention called a æpanelÆ) we estimate the proportion of SMU-sized parcels above a cut-off grade threshold. A series of proportions above cut-off defines the SMU distribution. Use of such non-linear estimates reduces distortion of grade-tonnage curves and provides a better basis for mine planning and economic decision-making. At present, Multiple Indicator Kriging (MIK) is the most widely used technique for performing estimation of recoverable resources. MIK is not the only approach available and it has some potentially serious limitations. The MIK technique is described and a number of theoretical and practical implementation issues are examined. In particular: MIKÆs assumptions about spatial distribution of grade; the behaviour of indicator variograms; application of change of support models; order relationship problems; and modelling the tail of the distribution. Some simple tests are described which allow us to determine the suitability of different estimators for a given deposit and criteria to identify a preferred estimator are also examined. Uniform Conditioning (UC), an alternative estimator which may be used instead of MIK, is described.

Jan 1, 2000

By D Willis, A Shanahan, C Jacobs, T Luxner

The application of tunnel boring machines (TBM) for reef mining is a unique practice with benefits over current mining methods given the right geology and geometry of the orebody. The Stillwater Mining Company (SMC) of Nye, Montana, USA operates two mines for obtaining platinum metals. The operation is currently using a 5.5 m diameter open-type machine for further mine development, as well as another TBM that they own.The latest 7.1 km bored tunnel, known as the Blitz Tunnel, will be routed parallel to the ore deposit in igneous mafic intrusive rock, and will be used for the life of the mine operation. It will be used to map the ore deposit, and provide a rail haulage route.Detecting the reef in relation to the TBM requires careful analysis. Diamond core drilling occurs ahead, above, and alongside the machine at every 150 m. The core is drilled, logged, and interpreted on the spot, concurrent with boring. Based on the data, the TBM is readjusted so that it stays on the correct bore path.This paper will highlight the application and benefits of TBM usage for reef mining, with detailed descriptions from the mine site.CITATION:Willis, D, Jacobs, C, Luxner, T and Shanahan, A, 2014. Tunnel boring machine usage speeds up development at Stillwater Mine, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 683–690 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Lane, S La Brooy

A century ago, new mines were often accompanied by smelters. In Australia, smelters were built at the Daydream mine near Broken Hill, at Kuridala and Mount Elliott near Mount Isa, Broken Hill, Mount Lyell, Mount Morgan, Mount Isa, and more recently at Tennant Creek, Kalgoorlie and Olympic Dam. Now the big miners eschew site-based processing in favour of shipping concentrate to smelters in Europe and Asia. As Chip Goodyear was in the process of vacating his leadership role at BHP Billiton, he was quoted as saying that BHP should concentrate on mining ore and leave æto others the skill set of processing that materialÆ. Yet there are times when on-site processing clearly makes sense. Few companies ship gold ore or concentrate to China for gold extraction. New smelters are being built in Zambia. Solvent-extraction and electrowinning plants frequently produce copper from oxide ores and concentrates while pressure leaching is increasingly being considered for copper sulfide ores. Some argue that on-site processing is best because the waste products can be returned to the ground from whence they came, avoiding potentially large disposal costs in more-populated areas. Copper treatment and refining charges will not remain at $45 per tonne and 4.5 cents per pound forever. This paper examines when it makes sense to use on-site pyro- or hydrometallurgical processes in todayÆs environment and comments on how current trends might alter the balance in future.

Jan 1, 2008

By M Clay, J Dunlop

Thermal and metallurgical coal mining in Queensland has resulted in mines which contain voids due to open cut mining. While there are several proposals for greenfield coalmines or expansions to existing operations, many existing open cut coalmines are reaching maturity and most will leave one or more residual voids in place. The rehabilitation of mine voids is challenging. Water held in voids will evaporate over time leaving solutes to concentrate. This is likely to lead to poor water quality with limited practical use. The most basic practices to rehabilitate voids have historically involved stabilising the high and low walls, bunding to provide flood protection, and preventing public access. Regulatory reforms for mine rehabilitation were introduced in Queensland as part of the Mineral and Energy Resources (Financial Provisioning) Act 2018, and aimed to strengthen progressive rehabilitation planning, limit risks to the environment and improve outcomes for local and regional communities. Under the reforms, the goal for rehabilitation of voids is to achieve a safe, stable, and non-polluting landform, which can sustain a post-mining land use (PMLU). The reforms also introduced a requirement to describe rehabilitation of mined land in Progressive Rehabilitation and Closure (PRC) plans, replacing the description of such plans in Environmental Authorities (EAs). The reforms are not retrospective and recognise historic approvals for voids, meaning established voids will remain in the landscape as non-use management areas (NUMAs). The objectives of this study were to outline historic void rehabilitation planning practices, describe water quality limitations of Queensland mine voids and identify possible opportunities for improved planning

Aug 2, 2023