Search Documents

By Bromley JC

Eimco Great Britain, a division of Baker Mining Equipment Company, was contracted to develop a hardrock tunnelling machine in conjunction with British Coal. The objective: a machine to cut rock up to 170 MPa compressive strength yet retaining the flexibility of roadheader type machines. This flexibility to encompass mobility, wide range of excavation shapes and sizes, simplicity of design and use, compact size, and efficient cutting operation. Current roadheaders operating in hard material are characterized by: 1. Severe machine vibration 2. Bouncing of the boom away from the rock 3. Very high pick wear 4. Inability to sump head in bad floor conditions The reasons for this poor performance can be attributed in part to: 1. High speed of cutting head rotation 2. Inability to hold boom against rock while cutting variable hardness strata. To overcome the problems described, a new articulation method was developed utilizing four hydraulic rams to "lock" the boom in position on one axis and four hydraulic motors to rotate the boom for cutting via a turret arrangement. The slide mounted turret is hydraulically advanced for sumping into the face, independent of the machine base. To transfer cutting forces back to the rock, the machine base is held rigidly in the excavation by floor to roof or side to side rams. A cutting head mounted on the boom rotates at very low speed, but with very high torque.

Jan 1, 1987

By Grant JR, McKavanagh BM, Dear SJ

A geophysical technique of rock mass assessment for engineering purposes is being investigated and shows positive correlation with direct structural logging and mapping techniques for the detection of major geological features. The technique is cross-hole acoustic surveying incorporating high speed signal averaging, with a maximum hole separation in excess of 30 metres in hard unfractured rock masses. The bulk of the field test work was carried out in open stopes in the copper ore bodies of Mount Isa Mines Limited. The investigation forms part of an integrated study of blasting in mining, aiming for fragmentation control through blast design modification. The rock quality factor, Q, is presented as a blasting index and can be determined for a significant portion of a production stope.

Jan 1, 1981

By Doyle P, Mulroney D

The Cassidy Shaft was sunk to access the Mount Charlotte and Reward Orebodies below the Flanagan Fault. The 1,184m deep shaft is concrete lined to 6.5m diameter for its full depth. The initial 590m was excavated by stripping into a 1.8m diameter borehole and hoisting the broken material through the existing mine. The remaining 594m was excavated by conventional shaft sinking methods. The shaft was sunk through 3 existing plats and an additional 8 plats cut. 1,800 tonnes of steel and 8 cables were installed during the furnishing of the 4 compartments.

Jan 1, 1985

By Leahy G. J, Moxon N. T, Nicol S. K

Experimental work is described in which extremely dilute aurocyanide liquors are treated with novel surface-active complexing agents to produce a hydrophobic aurocyanide species. Subsequent aeration of these liquors causes accumulation of such species at the air-water interface and the aurocyanide complex is transferred to a froth concentrate. A detailed performance assessment of this process is made and this knowledge used in the design of a pilot plant facility. Early results indicate the feasibility of the selective recovery of aurocyanide ions from reclaimed residue dam water (approximately 0.2ppm Au) with upgrade ratios of the order 180:1. A further study was made applying ion flotation to the recovery of gold from a carbon-in-pulp (CIL) feed liquor (approximately 1.0ppm Au). The probable economics of this process compared to conventional CIL processing is also described. Successful development of countercurrent ion flotation for concentrating solids-free gold solutions may offer a lower cost alternative to existing gold ore processing technologies, or in more secondary applications such as concentrating dilute gold solutions or heap leach runoff. The technology may also have more generalised applications to other heavy metal process- Ing.

Jan 1, 1991

By T Walkemeyer, R Elliott, D Chang-Martin

Over the past decade, discrete element method (DEM) simulations have seen increasing adoption by the resources sector to inform the design of materials handling equipment such as transfer chutes, bins and hoppers. But, if ‘all models are wrong, but some are useful’ (Box, 1979) what approaches are available to check that a DEM simulation is useful? How to avoid garbage in equals garbage out. This work considers what properties of bulk solid flow behaviour are important to transfer chute simulation. Cohesive bulk solids (such as sticky iron ore fines) can develop sufficient strength to form a stable cohesive arch, this phenomenon is not well predicted by measurements of angle of repose. This work presents a two-part approach to the development of a useful DEM model that can be used to add value to the design and optimisation of bulk materials handling equipment. Part 1 is the calibration of not just one, but a range of material models chosen to envelope the range of anticipated materials that will be handled. This work describes the DEM simulation of a batch of direct shear cell tests to develop material models that can be measured by the same metrics routinely used to characterise the flowability of cohesive iron ore fines. Part 2 of this work describes systematic methods for validation of the transfer chute DEM simulations. The DEM model is only useful if it can adequately represent the typical problems observed within a transfer chute, such as blockages due to build-up and cohesive arching. Proper validation requires good observations. Validation examples of site observations are shown side-byside with simulations to demonstrate the adequacy of the DEM model and calibration approach. DEM simulations have the potential to add significant value by allowing engineers and designers to predict material flow-through equipment based on a range of material properties, allowing for stress testing designs and making iterative improvements.

Sep 18, 2023

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

By E Wargem

The optimum mining of an orebody in an underground mining operation is fundamental to the mine’s ability to operate both sustainably and efficiently. The effective mining of an open stope or a cave is largely reliant on the recovery of the initial void created by conventional drilling and blasting. These initial voids are known by various names such as a Longhole Rise, Slot or Winze and can be mined either as a downhole or as an uphole. Regardless of the underground mining method, the process of the design and implementation of this initial void is largely uniform across many operations with various patterns of slot or winze designs used across these different operations. Diligent design, implementation and review strategies in drilling and blasting of these will facilitate cost-effective mining with minimal disruption to mine schedules and production targets. When an operation struggles in opening the initial void in underground mine blasting, it has a negative impact on productivity, mineral recovery, and the overall economics of mining. Near field blast vibration monitoring is a vital tool to use in analysing slot blasts and will provide additional feedback into the reconciliation part of the drill and blast process. It is one that is often overlooked in the mining industry in many operations due to many factors such as lack of skilled personnel, or a lack of required resources. The data obtained from near field blast vibration monitoring can be used to provide additional feedback into blast reviews and help in any drill and blast optimisation projects. This paper highlights key aspects of underground drill and blast reviews and the use of near field blast vibration monitoring for post blast analysis and shares learnings from various projects that the authors have been involved in within Australia and abroad.

Mar 29, 2023

By M Nagarajan

Orica Mining Services (Orica) in partnership with Coal and Allied’s Hunter Valley Operations (HVO) has developed a risk management process to maximise mining efficiency whilst controlling vibration and maintaining critical electricity continuity to New South Wales (NSW) electricity grid in the Riverview Pit. The issue is a high tension tower which supplies electricity located within 40 m of mining and blasting activities. The process involved developing an understanding of the relationship between vibration, explosives, geology and the location of the blasting in the geological horizon. From this an optimum methodology for blasting in each region was developed.

Nov 8, 2011

Commercial or potentially commercial deposits of coal occur in Australia in strata ranging in age from Permian to Tertiary. The coals of each period tend to show a community of petrographic character and significant differences as compared with coals of other ages. In particular- many of the Permian coals are unusually rich in inertinite whereas the Jurassic and Tertiary coals are typically very rich in vitrinite. The majority of the coals show evidence of deposition in environments subject to relatively minor marine influence. Except for some Tertiary and Permian coals the content of mineral matter tends to be high. Outcrops of coals of bituminous rank appear to be largely restricted to the eastern margin of the Australian continent. In this region vertical rank gradients are generally higher than in the other sedimentary basins and uplift and the removal of cover has occurred to a greater extent. To the west of the Tasman geosyncline, coal of bituminous rank generally occurs at considerable depths (usually in excess of 1 km and in some areas only at depths of over 2 kms), and in most areas coals at shallow depth are of sub-bituminous or brown coal rank. The controls of the distribution of coal type and rank have considerable economic significance and the unusual characteristics of Australian coals, especially with respect to coal type, make the direct application of overseas technology to Australian coals inappropriate.

Jan 1, 1975

By C Swamydas

VV Mineral (VVM) group of companies is the largest and the first private producer and exporter of beach sand mineral products in India. During 2010, the company produced and marketed around 750 000 tons of saleable products. Their operations are mainly in the state of Tamil Nadu and Andhra Pradesh, India. Almost all the wet pre-concentration plants use sea water as the concentration medium, since there is no fresh water source available near the deposits. The mines are located along the south-east coast of India in the states of Tamilnadu and Andhra Pradesh. The orebody varies in terms of mineral assemblage, slime content, grain size, and surface coating resulting in different behaviour of the minerals. Three different deposits containing ilmenite of different TiO2 content were studied. The study shows that there is no significant impact of using sea water for wet concentration prior to high tension separation of ilmenite. There is no significant variation in recovery and purity of ilmenite produced from these deposits when wet concentration of the deposits were carried out with sea water as the concentration medium and whether the concentrates were washed with fresh water or not before dry separation using High Tension Roll Separators (HTRS).

Oct 5, 2011

An underground storage and filling distribution system is presently being established at North Broken Hill Limited in the No.3 Shaft area. This has been necessitat- ed by the dependence of the present filling system on the No.2 Shaft and its imminent closure due to cessation of production. The storage will consist of three tanks excavated in low grade ore, between the No.20 and No.21 levels, at approximately 2700 feet below the surface. The tanks will each have a capacity of 1500 cu yds. Consideration was given for surface storage, although under- ground storage was thought to have greater merits. Two tanks have been excavated, and are in operation. Three or more outlets are installed beneath each tank, with horizontal connections into the No.21 level 'mixing box'. Water decants from the top of the fill in the tanks, and passes into a decant water sump, at the bottom of which is a borehole to the No.21 level. This is then connected to the mixing box and water used as make-up water with the semiwet solids for transport into the existing pipe distribution system. Preliminary results of the system have been satisfactory and it is envisaged that this system will readily cope with the filling demands of the future.

Jan 1, 1973

By Chend J

Research conducted into backfill drainage at Mount Isa Mines since 1992 is described. Piping in draining backfilled scopes has been the primary cause of bulkhead failures and emphasis is placed on research into the piping mechanism. Laboratory and in situ tests aimed at understanding the piping mechanism have been conducted and the results are presented. A case history of piping in a draining bench scope fill mass is described and a technique for reducing the potential for bulkhead failures in hench stopes is presented. Hydraulic fill is produced by standard cycloning of tailings and the overflow (reject material) is sent to thickeners prior to placement in the tailings dams. Research into the partial introduction of thickener underflow into the backfill system and its influence on backfill drainage is also descrihed.

Jan 1, 1998

By J Q. Cooper

The New Zealand rail authority, Kiwi Rail and Auckland Regional Transport Authority (ARTA), are jointly planning a new mainline rail link between Auckland’s downtown Britomart Station and the existing Western Line at Mt Eden. In 2009, APB&B, a consortia of Aecom, Beca, Parsons Brinkerhoff and Hassell Architects where commissioned to develop the conceptual design, Assessment of Environmental Effects (AEE) and business case for the new 3 km rail line towards preparing a Notice of Requirement to protect the route through Auckland’s central business district.This paper describes the engineering challenges in the development of the conceptual design for the three proposed underground stations, the running tunnels and connections to the existing network. Feasible alignment and station location options were developed and evaluated using multi-criteria analysis based on key client functional requirements, constraint mapping and environmental impacts. The resulting preferred scheme was then developed to a conceptual design suffi cient for assessment of environmental effects, risks, and the development of a robust construction methodology to allow high level capital cost estimates.The paper describes some of the major challenges overcome to develop the concept, including steep gradients, narrow street envelopes with existing buildings and structures, the need for large platform spaces with low ECBF rock cover and complex connections at Britomart and the main line near Mt Eden.The development of the conceptual design of the underground stations in particular demonstrates the need for a holistic value engineering approach to satisfying the architectural and functional requirements, in a highly constrained dense urban environment and at lowest practical cost. The construction methodology was a key input to the conceptual design development throughout.The conceptual design will be used as the fundamental basis for the development of the AEE and business case for the project in the future.

Mar 8, 2011

By P Waters, P Hollings, M Baker, D R. Cooke

Over the last three million years, porphyry and epithermal mineralisation in the Baguio Mineral District has been driven by calc-alkaline magmatism associated with the subduction of the South China Sea plate and the Scarborough seamounts beneath northern Luzon, Philippines. Coupled with extreme uplift and exhumation rates, mineralisation in the Baguio District has been responsible for the emplacement of over 922 million grams of gold. As one of the oldest intrusive bodies associated with the Baguio District, the Black Mountain Cu-Au deposit consists of at least five intrusive phases overprinted by potassic and propylitic alteration and sulfide mineralisation. Gold ore grades are low and molybdenum grades high with respect to other porphyry Cu-Au deposits in the Baguio Mineral District. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Y M. Lee, Y Hong, B C. Kim

Since sintered ore is the primary source for producing molten iron in the blast furnace process, maintaining stable quality despite the utilisation of low-grade iron ore is crucial. However, conventional analysis methods, such as chemical composition, ore size distribution and types of iron ore, have limitations in developing the utilisation of new low-grade iron ore and predicting sintered ore properties. Sintered ores are formed through a complex melting process of granule particles consisting of iron ore, flux and fuel. Consequently, it has been investigated that analysis methods which apply the reactive properties of iron ore to predict sintered ore characteristics. In this study, we estimated the properties of iron ore by simulating the assimilation process of coarse ore, which influences the bonding strength of sintered ores and quantifying the degree of assimilation reaction. Pseudo particles were formed by granulating coarse ore (1–3 mm) with adhering fines, which act as primary melts and sintered at 1623 K. The bonding strength of individual sintered ores, formed from 11 different types of iron ore, was measured using a simplified Tumbler Index (TI) test and each value was indexed as the Iron ore Reactivity Index (IRI). By investigating the relationship between the degree of assimilation depending on iron ore properties and the characteristics of sintered ore, we demonstrated that sintered ores formed from more reactive iron ore exhibited stronger bonding strength. Moreover, when blending conditions resulted in a higher Iron Blending ore Reactivity Index (IBRI), the physical properties of sintered ore improved. The development of this analysis method is expected to not only enable careful consideration of iron ore usability but also allow for the advance prediction of sintered ore qualities by deriving the IBRI.

Sep 18, 2023

By Nidagal V

This paper discusses the dewatering strategy adopted and the considerations and procedures required to incorporate a dewaterinq scheme into the Mt Whaleback mining operation. It concludes that in pit pre-dewaterinq has successfully allowed mining to progress below the standing water level with the minimum of disruption or radical change to the mining method. It is recognised however, that dewatering is not a static activity and there is a requirement for ongoing investigations and development. Pre-dewatering commenced in October, 1984. Purpose designed pumping trailers have been employed to minimise the loss of pump availability resulting from the frequent. need to remove and reinstall pumps when close vicinity blasts occur. To July, 1986, some 0.5 Mm' of groundwater had been pumped from the unconfined orebody aquifer. Mining has progressed to some 20 m below the standing water level without. any undue water associated problems. Ultimately, it is ,cheduled to extend some 300 in below the original water level in the West Pit. With the development of an increasing area of the mine below the standing water level, the influence of seasonal high intensity rainfall events, which had previously caused little concern, now need to be addressed. Pumping equipment has been designed to evacuate storm water at a rate consistent with mine production Considerations.

Jan 1, 1986

By A Campbell

Open pit blasting at Ernest Henry Mining has the potential to cause damage to nearby underground workings. This paper is a case study of the blast vibration management project that was conducted to ensure open pit blasting did not adversely affect the stability of upper production levels or cause damage to the underground primary fan units. The two upper levels of the underground mine surround the lower portion of the open pit mine. The remaining underground mine workings are directly below the open pit mine. This paper details the process developed to prevent open pit blasting causing excess vibration in the underground mine. Measurement of test blasts combined with historic blast monitoring data was used to determine site specific blast vibration parameters. Threshold vibration levels for blast-induced damage to underground drives and the fan chambers were developed from benchmarking and non-linear numerical modelling. A Monte Carlo simulation model was used to predict vibration levels in critical underground areas. Blasts predicted to exceed maximum vibration levels could then be redesigned to avoid damage.A scale distance law for determining peak particle velocity (PPV) from the distance and charge weight of blasts was developed. Underground observations were used to develop a site-specific relationship between PPV and ground support/rock mass damage. A Monte Carlo superposition prediction model was developed and compared to measured data to refine input parameters. Standards for redesigning open pit blasts in order to reduce blast vibrations whilst minimising impacts on productivity are described. Non-linear numerical modelling was used to establish the dynamic capacity of the fan chambers, and set a PPV of 250 mm/s as a threshold for damage. The numerical model captured the full dynamic behaviour of the fan chambers and installed support, including transient stresses, strains and induced damage, when subjected to a simulated open pit blast.This case study also outlines a procedure for monitoring and predicting blast vibrations at other mine sites where open pit blasting has the potential to impact on a nearby underground mine.

Nov 8, 2011

By Brathwaite RL

The gold-scheelite-quartz lodes of the Wakamarina valley were the most productive of the mesothermal gold-bear in the Marlborough Schist. Most of the production came from the Empire City and Golden Bar mines which worked tug, Golden Bar lode. Only 134 m of its 1800 m strike length are accessible, in the No. 2 level of the Golden Bar Mine. A fau I has downthrown the Golden Bar Mine section by 2 47 m and displaced it left-laterally by 18 m. The lode is a typical ribbon-banded mesothermal vein, averaging c. 1.75 m wide, and enclosing narrow horses of schist country rock. It i composed of bands of milky "buck" quartz with thin laminae of schist. Scheelite occurs in short strings of grains withi quartz on the footwall side of the lode and also in small quartz-carbonate veinlets in the foot wall and hanging wall schist The lode quartz contains only localised traces of pyrite and arsenopyrite. They are more abundant in the wall-rock schist.

Jan 1, 1995

By McCarthy P. L

A distinctive feature of the goldfields of Victoria was the extrac- tion of gold from deep leads, that is the buried river beds of Vic- toria's ancient rivers and streams. It is estimated that about 265,000 kg of gold was produced from Victoria's deep lead mines which comprises about 11.5% of Victoria's total production of gold (Bowen, 1974). The significance of deep lead mining for Victoria, however, went far beyond its economic contribution to Victoria. If Profes- sor Blainey is correct it was the frustrations of mining gold from deep alluvial leads in Ballarat during 1854 which precipitated the Eureka Stockade (Blainey, 1963, 46-52). This event resulted in the implementation of a fair mining administration and was an emphatic statement of the rise of democratic movements in Australia. Much of the technology and skill for mining deep leads had to be developed locally because at that time no other major gold- field elsewhere in Australia or the world had gold deposits with comparable problems. Deep lead mining in Victoria was there- fore largely a home grown industry and the equipment for that industry was often designed and produced in Victoria.

Jan 1, 1988

By Wickham P, Raeburn M. R

The design and development of slurry sampling equipment for the Mount Isa Mines Limited on stream analysis installations is discussed in detail. Emphasis is given to the critical areas of slurry transport, screen design, pump selection, elimination of fast wearing components and maintenance reduction. Sample point design to fulfil the specific accuracy requirements for On Stream Analysis (3% to 10% relative) is discussed.

Jan 1, 1976