Search Documents

By B McFadzean, N P. Lima, D A. Deglon

The reverse flotation of Itabirite iron ore is typically performed after a desliming step in which most of the sub-10 µm particles are removed. This is done to limit processing problems such as poor flotation recovery of SiO2 due to slime coatings and increased slurry viscosities, unmanageable froths and increased losses of hematite particles due to entrainment. However, the rejection of ultrafine particles contributes to large losses in iron recovery and may contribute to the instability of tailings dams. The aim of this study is to decouple the effects of ultrafine particles in the pulp and froth phases to better understand the processing capabilities of the fines fraction. The flotation test work was performed in a special-purpose continuously operated laboratory flotation cell that has a deep froth section to simulate plant-scale froth conditions. Five conditions of fines addition were investigated at three different froth heights and a solids concentration of 50 per cent. The behaviour of the pulp and the froth were decoupled using froth stability and froth recovery tests. This showed that, even though there is an exponential increase in froth stability at increasing fines quantities, the performance of the pulp has the overriding effect on the overall SiO2 recovery. Pulp zone, froth zone and overall SiO2 recoveries showed that overall recoveries increased by about 3.6 per cent for every 1 per cent decrease in fines content. This meant a large increase of 20 per cent in SiO2 recovery when going from undeslimed to deslimed feed. This was driven largely by increases in the pulp zone recoveries, which were about 4 per cent for every 1 per cent decrease in fines content. The froth recoveries, on the other hand, decreased by between 0.75 per cent and 2.5 per cent for every 1 per cent decrease in fines content, depending on froth height. This paper explores further insights into iron ore flotation processing at different slimes concentrations.

Aug 24, 2022

The procedure used for Truck Maintenance is described systematically in this paper. Emphasis is given to manpower required, work facilities, daily maintenance and oil sampling procedure. Scheduled Preventative Maintenance Service, Electrical Service, Component Change, Truck Overhaul and Outside Contractors are also discussed. The system used, achieves the required results with an average haul truck availability in 1981 of 87.9 per cent. INTRODUCTION Situated on the Island of Bougainville, in Papua New Guinea, the Bougainville Copper mine nestles in a valley near the crest of the Crown Prince Range, between 600 m and 980 m above sea level. The mine is serviced by two towns, Arawa - an open town on the Coast and Panguna at the Mine Site. Currently Bougainville Copper operates an open pit mine removing an average of 198 000 dry metric tonnes of material per day (115 000 tonnes ore and 83 000 tonnes of waste) with a fleet of electric shovels and 154 tonne electric haul trucks.

Jan 1, 1982

By B E. McCarthy

Red Dome Mine was a highly complex gold copper operation developed over a number of phases between mid-1986 to October 1997. With only three years of production ahead at any time, a proactive practical approach to mine closure was necessary. In 1989 the Domains Concept to life-of-mine planning and mine closure was created as a response to the proposed changes to legislation.The Domains Concept, a relatively simple idea developed to integrate mine closure during production at Red Dome, has been broadly adopted by both government agencies and industry in the intervening 20 year period. Over time the author has observed that the concept has been poorly applied, misunderstood and in some cases even misrepresented. As a consequence, the potential opportunities from applying the concept, including the optimisation and minimisation of life-of-mine costs, mitigation of long-term financial liability exposures and building credibility with the general community, have been missed.This paper examines the many benefits, advantages, applications and perceived barriers to developing and integrating a fully costed life-of-mine plan. Integrating the Domains Concept early in the project, within the operational budgeting, allows the production of a meaningful and useful document, representative of a whole life-of-mine, cradle to grave, with measurable rehabilitation and closure outcomes when the concept is used to full effect.The Domains Concept serves to optimise cost-effective, whole of mine, life cycle planning which provides beneficial outcomes for the community, significantly mitigates legacy issues and contributes to the attainment of compliance and sustainability principle objectives.CITATION:McCarthy, B E, 2014. The domains concept – 20 years on retrospective, obstacles and opportunities for effective life-of-mine implementation, in Proceedings Life-of-Mine 2014 , pp 621–636 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By T D. H McGrath, W P. Staunton

Benchmarking, comparing an operation or process with the industry standard, is known to be a useful method for identifying plant optimisation opportunities, and in many cases providing the pathway to realise the benefits. The difficulty is generating the database of plant data necessary for a benchmarking exercise. Larger companies can benchmark internally; this option is not available to smaller companies, and the full value can only be realised with a comprehensive “industry wide” approach.The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has undertaken several comprehensive metallurgical industry surveys in the gold industry over the last two decades. Analysis of these surveys has demonstrated areas where many operations can benefit from re-assessment of their operating practices.This paper will review the work undertaken by the Group in this area, in particular the 1999 surveys of gold companies in the Australasian region, and the 2012 international survey of the industry. The challenges of, and opportunities arising from these surveys will be discussed. Some of the highlights from analysis of these databases will be presented as well as noting changes in processing practices observed by the Group over the last 20 years.CITATION:McGrath, T D H and Staunton, W P, 2018. Keeping up with the Joneses – the value of industry surveys and benchmarking, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 509–516 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By Kwitko G

Exploration for coal has been on-going in South Australia for the past 100 years. During this period substantial resources of low rank coal have been delineated throughout the State. These deposits are of variable quality often with high moisture, sodium, chlorine, sulphur and ash content and although generally regarded as suitable for use in conventional pulverised fuel boilers, many are difficult to utilise. The only operating coal mine in South Australia is at Leigh Creek where coal bearing shale was discovered by chance in 1888 during excavation of a railway dam near the township of Copley. Leigh Creek has had a very diverse mining history from the initial small scale underground mining through to open-cut mining utilising draglines and more recently large shovels and trucks.

Jan 1, 1992

Professional engineers of today require a wide array of experience and knowledge. It is true that commonly engineering degrees do teach the technical requirements well, but do fall short in the way of teaching other non-technical issues of professionalism to the student. Today calls for an engineer who does not only have a high standard of the technical knowledge required for their degree, but also has a broad range of experience in areas that are becoming increasingly important in engineering. The importance of social responsibility, liability and interpersonal relations is high. Through the face of the changing world, it has become clear that there is a need for a new type of engineer, who has a broad range of expertise, as well as the typical technical abilities required. This paper will outline these non-technical issues and propose ways of combining these ideas into the mainstream engineering degree.

Jan 1, 2004

By I Arburthnot, N Lawler, C Loan

The function of a thickener is to optimise and accelerate the process of gravity sedimentation. The desired end product (be that maximised concentrated solids or clarified liquid) determines how the thickener is designed and operated.Significant internal research, together with extensive on-site piloting, by Outotec has resulted in the determination that the application of the appropriate amount and type of shear to hindered settling aggregates can result in a substantial change to the sedimentation process. A new patented technology, called shear enhanced thickening (SET), has been developed. SET results in considerable design implications for full-scale thickeners, including a substantial reduction in required footprint and/or significant increases in underflow density.The development of SET, combined with laboratory and pilot scale verification, will be discussed along with the introduction of this technology to a number of full-scale thickeners. The associated implications and benefits for industrial thickeners are outlined.CITATION:Loan, C, Lawler, N and Arburthnot, I, 2012. Industrial scale results from shear enhanced thickening technology, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 341-346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By Quayle J. E

This paper covers period from 1973 through to 1988 and the mines of West Coast Mines, Elur Mine, North Mine and Risdon Zinc Smelter, now all part of the Pasminco Group. During this period, optimisation started with one mine (West Coast Mines) producing four Product concentrates with constant steady feed to the smelter and progressed to three mines producing eight products and a smelter varying feed inputs to maximise benefits. The initial optimisation was done manually using a desk top calculator and hand drawn graphs. This ultimately advanced to the use of PC plus linear programming software and spreadsheet generating relevant graphics. The financial benefits were achieved with no capital expenditure and increased from an initial $0.5 to $1.0 M/year (1973 $'s) to $5 to $10 M/year (1988 $'s).

Jan 1, 1991

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By M Andrew, D McTiffen, M Adams

A major Ventilation Upgrade Project commenced at the Fosterville Gold Mine (FGM) in 2017 to service the ongoing ventilation requirements of the underground mining operation. The project consists of three large diameter ventilation raises totalling 1100 metres, and new axial primary ventilation fans to upgrade the mine ventilation system. With a mining depth of 1200 metres and a thermal gradient of approximately 2.7 °C per 100 metres of depth, the completion of the Ventilation Upgrade Project is key to the ongoing success at FGM. The Ventilation Upgrade Project will allow continued mining, including high-grade gold deposits, lower in the mine where heat is increasing. Figure 1 below illustrates the underground workings at FGM, and provides a general view of the ventilation upgrade works to establish the new exhaust system from the lower workings to surface. Whilst raisebore pilot drilling the H4760 Return Air Rise (RAR) from surface to 395 metres, the raisebore drill string became stuck in the raisebore pilot hole at approximately 300 metres down hole, presenting a significant technical problem and delays to the project. This Case Study provides an overview of the recovery process undertaken at FGM including the recovery of the stuck drill string. The value of the stuck in-hole equipment, the investment in the shaft site preparation, the collar stabilisation, the underground development to the base of the ventilation raise, the surface footprint prepared for the Primary Fans construction and the limited available space on the site were all motivations to recover the raisebore drill sting and ultimately recover the ventilation raise location. More importantly, the long lead-time required should a new shaft location be the final solution, and the delay this would incur to the ventilation upgrade was unacceptable. Recovery of the drill string was not possible using the capability of the Contractor’s Raise Drill. An alternative method for freeing the drill string was required. A significant amount of engagement with industry was undertaken to seek out potential solutions and draw from the experience of others. All methodologies available were considered and assessed. Ultimately, after several attempts at freeing the raisebore drill string using various methodologies, Adams Drillers and Clear Cut Interventions were engaged to provide a turnkey recovery solution.

Mar 15, 2021

By P M. Larionov, V I. Zaikovskii

Transmission and scanning electron microscopy together with X-ray spectral microprobe analysis were used to investigate the structure and chemical composition of pathological calcified formations on the bioprostheses of heart valves. Controllable synthesis was carried out under the conditions (T = 37¦C, pH = 7.4) when the ion composition of the main elements (Ca, P, Mg and NaCl) is close to their concentrations in blood plasma. It is proposed on the basis of the obtained results that the formation of the hydroxyapatite of calcific inclusions on bioprostheses occurs as a result of spontaneous precipitation in the blood plasma. One of the factors determining the formation of massive calcified bodies on the bioprostheses of heart valves can be decreased magnesium concentration in blood.

Jan 1, 2008

By F R. M Pires, R M. Carvalho

Supergene processes in banded iron formation (BIF) result in important dissolution, material transport and simultaneous disorder of the residual bands. The rock physical properties such as density, porosity and rheology change during the weathering attack. The itabirite, Paleoproterozoic metamorphic BIF from Quadrilßtero Ferrffero (QF) û Brazil, shows several weathered facies. Strong linking between topographic surface, rock density and iron grade occurs within the weathered zones. This linking is due to partial dissolution of silica and carbonate from itabirite and gravitational rotation and break of the remaining blades, generating kink-like slump structures. The original itabirite density, 3.7 t/m3, decrease at the first leaching steps, until 2.7 t/m3, and increase at the end of the leaching process until 3.6 t/m3. Iron grade increases from 38 per cent to 68 per cent and depressions (sinkhole), subsequently filled by Cenozoic basinal sediments, are developed over the enrichment zones. The formation of important supergene iron ore deposits of QF is intimately related to such a process. Several iron deposits at QF, such as Pico do Itabirito, Fßbrica Nova, Casa de Pedra, Tamanduß, -gua Claras, Cappo Xavier, etc., reveal the aspects related to the proposed evolution, implying that the formational process of the soft iron ores had a regional character. Granular medium model helped in the understanding of the development of the structure and the formation of the deposits. A numerical model has been developed in order to simulate a leaching system in a two-dimensional matrix, composed of two types of materials: leachable and unleachable. Equal volume proportion and vertical banding were considered. Drilling data was used as multipoint attractors to remove leachable matrix nodes.

Jan 1, 2002

By Carter NB

A statistically-designed experimental program has been used to study compositional and processing variables which influence the development of strength and reducibility of iron ore pellets. The effects of chemical composition and processing variables were investigated by indurating laboratory-made green pellets, of known composition, under approximately isothermal conditions in a pot- grate simulator. Some findings from a six- variable study are summarized in the form of contour diagrams and emphasize the importance of interactions between the variables. Production of strong, highly reducible pellets is possible over a considerable range of combinations of temperature and firing time. Abrasion index (AI) and cold compression strength (CCS) improve as both these variables increase, but reducibility (R) declines, so a compromise is required. When the lime level is too low to form enough slag for bonding, the AI and CCS may be inadequate. Larger additions of lime tend to improve AI and CCS, with only slight effects on R. Finer grinding of the balling feed (i.e. higher Blaine index) tends to improve Al and CCS without

Jan 1, 1980

By M I. Pownceby, N A. S Webster, A J. Studer, I C. Madsen, J A. Kimpton, M J. Fisher-White, L Lu

In situ synchrotron X-ray and in situ neutron diffraction-based experimentation have been implemented to characterise the formation of the complex calcium ferrite iron ore sinter bonding phases silico-ferrite of calcium and aluminium (SFCA) and SFCA-I. Experiments were carried out using fine-grained (<20 ¦m) sinter mixtures containing ~77 wt per cent Fe2O3, 14 wt per cent CaO, 3.5 wt per cent SiO2 and 5 wt per cent Al2O3, with diffraction data collected during heating until 1300 - 1350¦C, which was enough to ensure complete melting of the SFCA phases. In the case of the in situ synchrotron experimentation, results showed that altering the nature of the starting sinter mixture (ie substitution of goethite for hematite; substitution of an amorphous Al2O3-based mineral for gibbsite) did not have a significant effect on the thermal stability range of the SFCA phases. It did, however, have a profound effect on the formation and rate of consumption of the calcium-rich ferrite phases C2F and CF, and on the formation mechanisms of SFCA and SFCA-I. The in situ neutron diffraction experimentation is the first described in the context of iron ore sintering, and the observation of both SFCA-I and SFCA formation in the in situ diffraction data represents the first step in achieving the goal of charactering iron ore sinter phase formation in large volumes of industrial sinter starting materials with a wide range of particle sizes (up to 6.3 mm).CITATION:Webster, N A S, Pownceby, M I, Madsen, I C, Studer, A J, Lu, L, Manuel, J R, Kimpton, J A and Fisher-White, M J, 2013. In situ x-ray and neutron diffraction studies of silico-ferrite of calcium and aluminium iron ore sinter phase formation, in Proceedings Iron Ore 2013 , pp 487-494 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D R. Andrew, K T. Morrison, J F. Tiedgen

Waste blasting in iron ore operations can pose a number of technical challenges, including blasting through variable geology and blasting soft ground in wet conditions. Blast patterns are designed to be loaded with a specific range of explosives with unique characteristics and properties. Each explosive product will produce an optimal blast outcome for a given set of blast parameters and ground conditions. Sites characterised by softer rock typically require low-density, low-energy explosives. Historically, these products have contained a high ratio of porous ammonium nitrate prill and are only suitable for dry blastholes. When blastholes within a pattern are found to be unsuitable for such explosives due to wet, damp or muddy blasthole conditions, a new product is selected. While it is easy to switch products to match blasthole conditions, the different properties of the new non-ideal product can impact blast performance and increase loading times and costs.Flexigel™ is a solids-sensitised emulsion blend suitable for loading at variable densities and energies in dry, damp, muddy or wet blastholes. It is a universal product that can be loaded to match ground and blasthole conditions or complement other explosive products.At Fortescue Metals Group’s Cloudbreak site, Flexigel™ was trialled through a series of matched pair blasts in order to optimise blast outcomes in conditions that were non-ideal for existing explosive products and to reduce the overall cost of drill and blast operations. Flexigel™ yielded improved instantaneous dig rates and improved loading efficiency when compared to a traditional emulsion blend. The results also indicated that variable-density and variable-energy products afford greater flexibility for optimising blast outcomes across all ground and blasthole conditions trialled.Trials of Flexigel™ at Cloudbreak have shown that a variable-density solution is available for conditions where traditional explosive products are non-ideal. As such, Flexigel™ is able to fill a major void at any operation where the desired low-density, low-energy explosive product must be substituted for a more expensive traditional emulsion blend or heavy ammonium nitrate/fuel oil.CITATION:Andrew, D R, Morrison, K T and Tiedgen, J F, 2015. Flexigel™ – a variable-density solution, in Proceedings Iron Ore 2015, pp 413–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By M Akop, G Phillips, L Elliott

An estimation geologist has many tools in their kit and using the correct one for the job is vital for creating a useful model. Reconciliation is a key step to monitor the performance of a resource model and to ensure the correct tools have been selected and appropriate parameters are set. This paper presents an example of refining the estimation methodology for a Channel Iron Deposit (CID), resulting in an improved model. Rio Tinto Iron Ore (RTIO) CIDs are unique iron ore deposits located in the Pilbara region of Western Australia and contribute a significant volume to the world’s seaborne iron ore market. A problematic feature of these deposits is the irregular dispersion of clay pods that cannot be delineated with confidence within the resolution of the exploration drilling. Resource to grade control reconciliation showed an over-prediction of high-grade material in the resource model. A fresh approach was required to improve grade and tonnage predictions. Historically, clay pods were delineated using traditional wireframing techniques and estimated using ordinary kriging with hard boundaries. The new method utilised indicator kriging to estimate the probability of clay. Probabilities generated from the indicator kriging estimate were used as an additional weighting following the ordinary kriging of grades. Results showed indicator kriging improved global high-grade tonnes reconciliation, however, as expected, it did not improve the spatial prediction of clay. Based on improved reconciliation results indicator kriging has now been adopted as a suitable alternative for analogous CIDs at RTIO. These improvements benefit the mine planning process, but do not replace grade control models.

Mar 22, 2022

By P A. Montoya

La Colosa is a world-class porphyry Au project located in Colombia, currently undergoing prefeasibility analysis. As part of collaboration between AngloGold Ashanti and the AMIRA P843A GeMIII Project, the application of emerging geometallurgical characterisation testing and modelling tools has been incorporated in early stages of project development. The aim of the geometallurgical study is to map inherent comminution variability across the La Colosa deposit providing information critical for mine/mill design and optimisation. In this study, site-based data incorporating multi-element assays, quantitative analyse X-ray difraction QXRD bulk mineralogy measurements, EQUOtip rebound hardness data, and routine geological logging information from 59 diamond drill holes has been integrated with a range of geometallurgically specific comminution test (ie GeMCi, A × b, BMWi). The work in this paper demonstrates the integration techniques used at La Colosa to link routine data acquisition methods with comminution test results through the development of proxy support models. The integration incorporates a range of statistical techniques including principal component analysis and regression modelling. By creating proxy models, comminution index estimates can be propagated into the geological database enabling comminution processing domains to be defined. These domains provide the first spatial representation of comminution performance and variability at La Colosa and can be compared against traditional geological domains. This study provides the foundation for ongoing comminution characterisation as the La Colosa project evolves through project cycles into an operational mine.

Sep 5, 2011

By S Watson, L Martinez

Mine projects are complex opportunities that demand a constant assessment of uncertainty, ie risk and upside potential. This is because the value of a mine project is typically influenced by many underlying economic and physical uncertainties, such as metal/mineral prices, metal/mineral grades, costs, schedules, quantities, and environmental issues, amongst others, which are not known with much certainty at the beginning of the project. But, is uncertainty an enemy or an ally of the mine planner/analyst? To answer this question, this paper first assesses and elaborates upon the general concept of uncertainty. It then looks at the different sources of uncertainty in a mining project, such as the orebody, costs and product price uncertainties, and their effect on the final project value. Next, a general?review?of current mine evaluation techniques highlighting their limitations when dealing with uncertainty is made. Finally, an extended evaluation and risk management framework that addresses the existing uncertainty in the (greenfield/brownfield) mine evaluation process is proposed. One important characteristic of this framework is that it uses and manages uncertainty in order to generate additional value to the project; this is done through operational and managerial flexibility, which allow mine planners to minimise/maximise project risk/upside-potential giving a more realistic estimate of the projectÆs market value - this is shown in practical and simple examples occurring at different stages of a mine project, such as exploration and operation. Final conclusions are provided at the end.CITATION:Martinez, L and Watson, S, 2012. Uncertainty - An important source of (additional) value for mine projects, in Proceedings Project Evaluation 2012 , pp 131-140 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By A Fyans, B Ghahreman-Nejad

This paper discusses the method and results of an options study into selection of the optimal form for a 130 m high tailings/water retaining dam, located in a region of high seismicity in central Iran. The proposed dam is part of a planned expansion project for Sarcheshmeh Copper Mine (SCM), which after construction will provide 550 million tonnes of additional tailings storage over the next 27 years. Geotechnical investigation at the proposed site indicated that adequate suitable low permeability materials (i.e. clay) were not available in the immediate vicinity of the dam site and would need to be imported from a distance of well over 10 km (direct). Given the magnitude of the estimated quantity of material and construction cost it was considered prudent to compare the cost of alternative dam design options for the proposed storage. A total of five dam design options are considered including a conventional rockfill embankment dam with an upstream sloping earth core (ECRD), a geomembrane face rockfill embankment dam (GFRD), a sloping asphalt core rockfill embankment dam (ACRD), a roller compacted concrete dam (RCCD), and a filter rockfill embankment dam for tailings storage together with a separate smaller earthfill core rockfill dam (ECRD) located downstream for storage of decant water. The risks, costing and design of all options are discussed in detail and the outcome of the study is presented.CITATION:Ghahreman-Nejad, B and Fyans, A, 2018. Optimum embankment design for a tailings dam, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 427–438 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018