Search Documents

By R Jaine, D Strang, M Fowler

"This paper presents a case study demonstrating active geotechnical pit slope management at the now completed Carina Iron Ore Project operated by Mineral Resources Ltd (MRL). The site is located 105 km north-east of Southern Cross, Western Australia. The paper is primarily focused on the slope stability failure modes and the remedial measures employed to maintain mining.Between a quarter and a third of the excavated slopes were impacted by some form of instability that was beyond expectations of the intended slope design criteria and common practice. Ongoing mining was supported by intensive geotechnical pit slope management including close cooperation between geotechnical, mine planning and operations staff to achieve timely and practical mining solutions.Mining encountered varied slope failure mechanisms which required a combination of remedial solutions comprising: horizontal depressurisation holes, deferral of excavation, unloading, buttressing and catch berms.The root cause of the challenging slope performance was a mismatch between the predicted and encountered geotechnical model, resulting from a failure to recognise the critical mechanisms that control slope stability.Despite the extensive zones of instabilities at completion of mining, full ore recovery was achieved without major delays and in a controlled and safe manner.Citation:Fowler, M, Strang, D and Jaine, R, 2016. Adapting to Geotechnical Change - a Case Study of the Carina Open Pit Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 150–161 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

By M S. Tuohy

Since the independent review of fatal accidents in the mining industry carried out by Dr Sean Brady (the ‘Brady Review’), High Reliability Organisations (HROs) and their operating principles have been discussed across the Queensland mining sector. HROs are organisations said to consistently avoid serious failures, reliably delivering their organisational objectives despite operating in environments characterised by high levels of inherent risk and/or operational complexity. HRO concepts have previously found application in other similarly hazardous industries to mining. However, as Hopkins (2009) pointed out, HROs ‘are very elusive creatures that inhabit the realm of theory more than the real world’. The Queensland Resources Council (QRC) with support from the Commissioner for Resources Safety and Health initiated a review of how HRO principles can be translated to the mining industry. The review was conducted by Noetic, an Australian management consulting company that specialises in hazardous industries, including mining and metals, and has prior experience applying HRO theory.

May 5, 2022

By R Wynn, T J. Akroyd, C Costa

In an environment of lower zinc prices, falling revenues and reducing zinc feed grades, Century mine implemented a fast-tracked capital upgrade program in less than 15 months. The program was designed to increase ore milling throughput capacity by 20 per cent and optimise the capacity of the flotation plant to increase zinc recovery by approximately 2.5 per cent whilst maintaining final zinc concentrate grade.A key aspect of this program was minimising capital expenditure by better utilising existing capacity and only adding capacity where absolutely required to address critical processing bottlenecks. By gaining an understanding of plant process bottlenecks and future ore blends, and by carefully selecting appropriate technologies for particular specific flotation applications, maximum return on minimal capital investment was achieved.The close collaborative work achieved between the metallurgy processing department and other operational departments on-site was also critical to the success of this project. This work increased the mining and processing capacity of the mine and port site respectively, such that the full value of the process plant modification could be achieved.Capital payback on this investment was achieved in approximately three and a half months.This case study demonstrates the extra value to a mining business that can be achieved through fully understanding the mining/processing value chain and by careful targeted action to address critical bottlenecks in the processing chain from the mine through to the port site.CITATION:Akroyd, T J, Wynn, R and Costa, C, 2014. MMG Century Mine, a case study – maximising project net present value through targeted capital expenditure and process optimisation against a backdrop of falling metal prices and feed grades, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 417–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By M Rafty, C Lane

Managing water is a key aspect of mining, whether a site is in water surplus or water deficit. Water in tailings storage facilities (TSFs) needs to be managed carefully to maximise the density of the solids, maximise the re-use of available water and to minimise the risk of water overtopping the spillway in the event of heavy rainfall. Developing a water balance models is a standard method for monitoring the major flows of water around a site. However, models created by specialist consultants are often overly complex and are not suited to being used by process plant personnel after they have been handed over to the mine operator. Models typically offer information on water management at the time that they are created, but then ‘sit on the shelf’ and offer no further insight or value for operating mines. Advisian has developed a customised water balance model for a mine in Sub-Saharan Africa, which can be adapted to other locations, to assist in managing water at the site and in particular to predict the current and future water level and volume in the TSF under various rainfall scenarios. The model was developed using Microsoft Excel and requires no specialist skills to operate. Site personnel enter in daily production, water transfer and rainfall data and then view the output dashboards to observe the current water level and volume, decant rates, licensed water abstraction and water supply versus demand. The output dashboards were developed in close consultation with the client to ensure that all of the relevant key performance indicators were included, from the perspectives of all the key stakeholders. This modelling approach focusses on the needs of the people who will actually use the model to actively manage TSFs with the need to involve the model developer as part of ongoing operations eliminated. The simplicity of this approach is now being embraced by other mine sites in Africa and Australia. CITATION:Rafty, M and Lane, C, 2018. Water balance management 101, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 485–490 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By Clark GH

Batu Hijau is a porphyry copper-gold deposit located on Sumbawa Island in the western Banda Arc of Indonesia. The deposit has been evaluated from 54000m of drilling in 105 diamond drill holes over a surface area of 1.2km2 and to a depth of 1000m below surface (412m below sea level). A provisional plan is being evaluated to mine 642 million tonnes at an average grade of 0.61% Cu and 0.55g/t Au (variable cutoff) from an open pit in the higher grade portion of the resource. The deposit is associated with a caic-alkaline intrusive complex that was emplaced in a thick sequence of andesitic pyroclastic rocks. The oldest and most widespread intrusion is porphyritic to medium-grained, equigranular, quartz hornblende diorite. At Batu Hijau the western diorite contact zone was intruded by two phases of tonalite. The older tonalite is a stock increasing from 200m diameter at surface to 500m at sea level. It consists of quartz, plagioclase and hornblende phenocrysts set in a groundmass of similar composition. A younger tonalite intrudes the tonalite stock, quartz and plagioclase phenocrysts are more abundant and it has a finer groundmass than the older tonalite. Brecciation occurs near the older tonalite contacts but there are no breccia pipes or late-stage features such as pebbldykes or postmineralisation intrusive rocks.

Jan 1, 1995

By O Bascur, A Soudek

Large metallurgical complexes are substantial users of energy, water and assets. To improve the effectiveness of energy and assets the quality of the data and events become paramount for real-time operational management. A lack of resources at the local operations and at the enterprise makes it impossible to process the sea of information and many projects have failed. As such, a novel approach for implementation of continuous improvements at the local level and innovations at the strategic level was implemented at all operating plants at Anglo American Platinum. Sixteen concentrators, three smelters and two refinery process systems were integrated to scale the information for manufacturing services at the local and enterprise level. The new capability of an enterprise real-time monitoring and diagnosis software infrastructure was available to implement many business strategies in tandem. Mineral and metallurgical processing knowledge is used to simplify the implementation of the data model. As such, asset monitoring, energy, production and process control management were implemented in an integrated approach reusing the same data but with different context and time horizons to have a standard methodology for local root cause analysis. This paper will highlight a sustainability management approach to change and empower the local and strategic team to collaborate using a new approach for adaptive reporting and condition-based event management and notifications. The results based on the integrated and collaborative team efforts will be presented. OSIsoft Plant Information system was installed and configured to achieve a targeted reduction in energy consumption of 15 per cent by 2015.CITATION:Bascur, O and Soudek, A, 2014. Implementation strategies for energy effectiveness and sustainability – example of Anglo American Platinum, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 101–108 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By W Ludlow, C Harrington

This paper presents an overview of the design and construction challenges to implement capping systems on Tailings Storage Facility’s (TSF) based on recent projects in Australia. Key aspects discussed include the cover design and barrier system to encapsulate the tailings, designing for a service life of 1,000 years, water management considerations. construction on tailings, vegetation selection and agronomy of the available capping soils plus the Health, Safety and Enivornmental challenges faced in working on tailings. Lessons learned from experience in capping TSFs are also presented. CITATION:Ludlow, W and Harrington, C, 2018. Experience with Capping of Tailings Storage Facilities for Decommissioning Projects in Australia, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 157–165 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Stipcevich, N Patel, J Faithful5, S Narendranathan, L Tatnell4

ENGIE, the current owner and operator of the Hazelwood Open Cut coalmine, are in the process of rehabilitating the mine site in preparation for mine closure. Bucket wheel excavators (dredgers) used during coal mining operations are in the process of being demolished, which involves the controlled felling of dredger components using explosives. With the mine located in close proximity to the Morwell township and other critical public infrastructure, it is crucial that the use of explosives and the possible implications for mine stability is well understood. The felling of Large Mining Equipment (LME) will apply an impact load immediately to the underlying coal benches with the adjacent coal batters potentially at risk also of adverse slope stability impacts. This paper presents the 3D stability modelling methods employed to successfully assess the potentially adverse stability implications associated with LME collapse.

Jun 21, 2022

The Telfer Underground sublevel cave (SLC) Operation is located approximately 850 m below surface. The cave was designed to propagate through an old decline which was initially used to monitor the cave. There was a requirement to install air blast plugs at two locations in the old decline in order to isolate any potential air-blasts from the active workings in the event of the rock mass collapsing into the cavity. There was a further requirement for an air-blast plug in another section of the mine where there was a risk of the cave intersecting an old workshop and providing an air-blast pathway through an abandoned incline. The design criteria for the plugs was that they should withstand the design air blast loading, be free draining, cost effective and easily constructed with the mining expertise available on site. A plug consisting of grouted mullock was considered robust and least challenging to construct. For the purpose of estimation of maximum air pressure on plugs, it is supposed as a worst case that the rock above a cave falls as an airtight piston onto the top of a muck pile, forcing air into it and also mine workings intersected by the cave. Airflow through the muck pile is governed by Ergun's equation for turbulent flow. In a time-stepping integration scheme, transient air pressures and velocities are calculated according to equations of thermodynamics, in the cave and at intervals along intersected drives by means of a finite difference spatial discretisation. The ability of plugs to withstand computed pressures is assessed by finite element elastoplastic analysis. This paper outlines the rationale for potential air blast loading, calculation of transient air pressures, plug design and analysis of plug behaviour. The plug construction method is also discussed.

Nov 25, 2010

Gold is actively precipitating at grades up to 80 g/tonne at and near the surface of the Waiotapu geothermal system, located in the Taupo Volcanic Zone of New Zealand. Many characteristics of this active system makes it analogous to the environment deduced for epithermal precious metal mineralisation in the circum Pacific region.The near surface area of the geothermal system is approximately 17 km2, caused to an extent by the upflow of deep, neutral pH fluids being deflected into a lateral flow of several km. This fluid has pervasively altered the rhyolite pyroclastic and ash deposits to an assemblage generally characterised by the term propylitic; major vein mineralisation is not observed. The temperatures at the 1100 m limit of drilling are 300¦C, and decrease to the surface along a boiling point curve.Condensation of steam and H S (subsequently oxidised) at the surface (derived 2from deep boiling) results in the formation of heated acid sulphate waters. These have caused a shallow (50 m) cap of advanced argillic alteration. Mixing of this oxidised condensate with the deep neutral pH fluid appears to be the principle cause of gold deposition from thiosulphide complexes. The major focus of gold mineralisation is in Champagne Pool, a hot spring which fills one of several 900 year old hydrothermal eruption craters.

Jan 1, 1984

By R M. Krek

The haulage system used to convey ore from an underground mine to a surface stockpile at the mine process plant is a vital component of the mine’s overall infrastructure and economic viability. The system selected has a significant impact on the set-up of the mine and the access to the underground mine. In turn, the set-up of the mine and the access to the underground mine have a significant impact on the system.A number of haulage technologies are available to transfer the ore from the underground workings to the surface stockpile, including hoists, conveyors, rail and trucks.This paper focuses on the shaft hoisting and inclined conveyor haulage technologies. These technologies have been used consistently to deliver ore from at depth and/or at high tonnage. Previous reviews of the appropriate vertical haulage systems have nominally been restricted to the respective systems only, with no consideration for any other scope or issues that may affect the selection. The selection of the appropriate vertical haulage system, whether shaft hoisting or inclined conveying, needs to consider numerous key factors.CITATION:Krek, R M and Northcote, A E A, 2014. A holistic viewpoint for selecting the vertical haulage system – shafts and conveyors, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 289–296 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By A Fern, A Hawkes, o, T Vincent

The modern workplace has changed dramatically in recent years with an increased emphasis on the psychological well-being of employees. While adhering to a certain standard of psychosocial safety at work is now not only a moral, but legal obligation in Australia, it begs the question: how can organisations begin to ensure psychosocial safety? A positive psychosocial safety climate is one where employees feel they are psychologically safe, feel supported in their work and are not exposed to work-related stressors that can negatively affect their mental health. Such a climate can help boost productivity and create a more positive working environment. This presentation will provide a twopronged approach to understanding and managing psychosocial safety: pairing a traditional risk assessment with climate measurement. Risk assessments can provide several benefits, including identifying and characterising work-related hazards, identifying the nature and severity of the risks to employees and prioritising necessary interventions for reducing or preventing psychosocial harm in the workplace. However, these assessments can have certain limitations, especially when it comes to capturing some of the less obvious causes of psychosocial harm. Climate measurement can provide valuable insights into employees’ perceptions of the work environment, identify areas of concern that may not have been identified in the risk assessment and help to guide organisational changes that will enhance employees’ psychosocial well-being over time. It will also be argued that climate should be assessed from a broad perspective exploring general, physical, social and psychological aspects of safety climate. This presentation will explore why conducting risk assessments in conjunction with detailed climate measurements is integral to protecting the psychosocial safety of employees in the workplace and demonstrate why employers should view the two approaches as complementary and interconnected. Best practice recommendations will be provided for the risk assessment, climate measurement and psychosocial interventions

Apr 16, 2024

By A Melkumyan, K Silversides

The banded iron formation-hosted iron ore deposits located in the Hamersley Ranges of Western Australia contain marker shales that are used to distinguish lithology for geological and orebody mapping. These marker shales produce distinctive signatures in the natural gamma downhole logs, which are conventionally manually interpreted. This paper proposes an alternative method of automatically identifying these shales using dynamic time warping (DTW). A Gaussian processes (GPs)-based method for automatic identification is also considered. Both methods are tested on a deposit that contains the Marra Mamba sequence of the Hamersley Province.Both methods were trained to predict the location of the desired shales, and the resulting outputs were compared with a manual interpretation of the results to determine the accuracy. The GP method can identify signatures with an accuracy between 87.0 per cent and 92.0 per cent, which increases to 92.9 per cent and 95.7 per cent where the GP is certain. The DTW method has an accuracy between 90.0 per cent and 91.6 per cent, which increases to 94.0 per cent and 95.4 per cent where the DTW is certain.The GP method has several advantages, including a more automated library building process, a probabilistic output and a shorter run time. However, the DTW method was capable of accepting more distortion in the signature and therefore identified more signatures. This is important in a deposit where the signals are frequently distorted by events such as hydration and folding. Both methods provide a viable alternative to the current manual detection, but their differences make them applicable to different cases.CITATION:Silversides, K and Melkumyan, A, 2014. Comparison between Gaussian processes and dynamic time warping for classification of marker shales in iron ore deposits, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 177–184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Seccatore, T Marin, M Cardu, G De Tomi, F Galvão, A Rezende, E Melo

Small-scale mining operations are characterised by a large variety of equipment availability and a high level of operational flexibility. Mine planning is usually scarce or absent in small quarries in Brazil, and mine management generally focuses on daily operations. As a result, analysis of the effects of unit operations, such as blasting, over the whole mining process is often neglected. The goal of the following project was to study the effect of production blasting on loading and hauling times, secondary breaking times and primary crushing times at the Experimental Mine of the Research Center for Responsible Mining of the University of São Paulo, Brazil. The operations analysed included blasts that performed:under the average operational standard, defined in this paper as Case 1according to quarry standards, defined in this paper as Case 2.In order to establish the effects of blasting on the downstream process, three key performance indictors were used:The time taken to load the truck, when there is the need for material selection. Due to the fact that we do not have an operational baseline, the increase in time cannot be established, meaning that we must content ourselves with comparing the mean time in each scenario.The average time used for secondary breaking machinery.The time required for the primary crusher to fully process the load of a single truck. The results obtained indicate correlations between the coarseness of the blasted material and these operational times. Solutions are suggested and evaluated for the improvement of the small-scale mining process.CITATION:Marin, T, Melo, E, Seccatore, J, Cardu, M, Galvão, F, Rezende, A, Bettencourt, J and De Tomi, G, 2015. The effect of drilling and blasting performance on fragmentation in a quarry and time for loading, secondary breakage and crushing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 355–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By J V. Mehrabani, A R. Sayadi

Adequate estimation of equipment costs is a key factor in a feasibility study and in evaluation of design alternatives for mining and mineral processing projects. Inaccurate early cost estimation could lead to the elimination of investment benefits. However, this estimation is complex and time consuming because of data accessibility problems and consequently access to a rapid, up-to-date and accurate tool is desirable for carrying out cost estimations.This paper describes the development of models for estimating capital and operating costs for a jaw crusher, which is used as the primary crusher for a wide variety of mineral beneficiation plants, applying single and multivariate regression analyses, together with the design of experiment approach, based on principal component analysis. Explanatory variables include gape size, length of feed opening and power as numeric (quantitative) variables and toggle type (single or double) and the existence of extra heavy duty construction as categorical (qualitative) variables. The performance of each model has been investigated and comparing the estimated R-squared (R2) of each model, the best was selected and its validity examined. The cost models include the capital and operating costs along with the operating cost components. The results indicate that the suggested best cost model is sufficiently accurate for use in feasibility studies.

Sep 26, 2011

By J Manuel, A Trudu

Regulations on the emission of particulates from sinter plant stacks are becoming increasingly stringent and reducing these emissions by improving gas cleaning systems is a significant cost to the sinter plants. This paper describes an investigation into the emission of particulate matter from an iron ore sinter bed during the sintering of a Japanese Steel Mill (JSM) style ore blend in a 300 mm diameter pot grate test facility. Several techniques were trialled to determine a reliable method to sample the quantity of dust emitted and determine the mechanism of dust emission from the sinter bed. The nature of the dust was also examined using chemical and size analysis as well as optical and scanning electron microscopy. The paper discusses the techniques used to carry out the program as well as results on dust loading measured during sintering and the nature of the dust captured.

Jan 1, 2002

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By A Crawford, P Manton

Telfer is a gold/copper operation, currently operating one open pit mine and one underground mine. The ore processing plant consists of two parallel trains involving semi-autogenous mill, ball mill and crusher (SABC) grinding, flotation and leaching. Due to receiving relatively high grade underground ore for over half of its total feed, Train 1 frequently experienced cleaning circuit overloading during high production periods. This resulted in losses in recovery and ineffective concentrate upgrade. As a quick and simple solution, the Train 1 copper flotation circuit was reconfigured to send concentrate from the first two rougher cells directly to the final concentrate and return the cleaner scavenger tailings to the third rougher cell. These modifications have resulted in a 1.4 per cent increase in plant copper recovery with no change in final concentrate grade. Preliminary results also indicate gold recovery has increased by more than 1 per cent since the circuit reconfiguration. Other benefits include less spillage, more friendly circuit to operate and a more consistent metallurgical performance. Focus for the next phase of optimisation is on concentrate upgrade. A number of opportunities have been identified and are currently being investigated, including staged reagent addition, single stage cleaning of the first two copper rougher concentrates, regrinding of the remaining copper rougher concentrate prior to cleaning and process control based on a machine vision system.

Jan 1, 2009

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007