Search Documents

By M J. Thurley, M Wimmer

To assess the present-day functionality of large-scale sublevel caving at LKAB Kiruna a comprehensive measurement program was undertaken involving blast function, fragmentation and gravity flow. As part of this assessment, a fragmentation measurement trial was performed based on 3D imaging of the drawpoint and corresponding bucket load of the underground load-haul-dump (LHD) excavator. 3D image data from stereo photogrammetry was collected and an automated image analysis strategy developed. A number of data sets were collected for each of the drawpoint and LHD bucket, along with sieving results for four of the LHD bucket loads (totally about 70 t). Two of the sieving results were used to inform the automated image analysis strategy, and two were held back as a comparison. Large variations in the visible particles are apparent when comparing corresponding drawpoints and LHD buckets highlighting the impact of sampling location and the need to measure large quantities of data in order to avoid bias from small samples. The results show that 3D imaging and analysis can produce fully automated measurement and analysis of the visible particle size distribution. Although this is not the same as the sieve-size distribution it provides useful estimation of both the larger size classes and a bulk estimate of fine material below approximately 60 mm. The 3D stereo photogrammetry measurement system used produced very high 3D point density but this was achieved using a custom up-sampling technique which significantly smoothed the data, removing small particles, smoothing edges, and this negatively affected the particle delineation algorithms.CITATION:Thurley, M J, Wimmer, M and Nordqvist, A, 2015. Blast fragmentation measurement based on three-dimensional imaging in sublevel caving drawpoints and underground excavator buckets at LKAB Kiruna, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 763–774 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By T N. Little

This paper is concerned with the influence of engineering geology on design of Wall Control Blasts. In the Introduction, the Blast Management Framework and the Blast Design Requirements classification system (previously developed by the author) is drawn upon to set the context. Blasting objective for all wall control blasts involves both profile and damage control. Four classes of approaches for blast design are outlined and briefly discussed. Five distinct wall control blasting techniques are summarised. The general relationship between geology and blast design is explored in the paper. Influence of geology on pre-split and post-split design and blasting direction is highlighted. Wall damage modelling from the closest row of blastholes is also introduced using the Analytical Damage Model (ADM). The relationship of rock properties and explosive selection and in particular the Mach wave generation is introduced to assist blast designer in this regard. Finally a Conceptual Model that relates vibration, damage and rock mass condition has been presented along with some applications that have been undertaken by the developer. Eight conclusions have been formulated based on extensive work in this area and the current study.

Jun 22, 2022

It is difficult to evaluate exploration properties in a manner that is transparent, repeatable and easily re-calculated to cater for different geological interpretations, but the risk-based assessment methodology, the Geological Risk Method, developed and described by Lord et al (2001) attempts to satisfy all these criteria. This paper examines a case study example based on valuations of exploration projects conducted by SRK Consulting using this methodology, and describes some of the advantages and limitations of the method.

Jan 1, 2007

This paper attempts to put into perspective the implications of the legal disclosure requirements for promoters and consultants when making statements concerning ore resources and reserves. The need to take account of non-technical as well as technical factors is highlighted.

Jan 1, 1987

Open pit mines in the Yilgam Craton have unique hydrogeological characteristics resulting from a combination of geology, mineralisation and the complex and extended development of the regolith. The principal features of this geological relationship are:ò deep and complex multi-stage development of the weathering profile; ò steeply dipping rock layering;ò supergene enrichment; andò mining across the regolith/rock interface.These features result in large changes in permeability horizontally across rock layers; vertically through the weathering profile and along-strike in association with mineralisation and the mineralised Structure.

Jan 1, 1993

By C K. Boafo, J Visser

Obuasi Mine in Ghana, with more than 100 years of mining history, developed from a surface operation into a deep >2000 m underground gold mine. The challenge is to extract value from narrow veins left after extensive mining in the wider ore zones of the mine. Since the merger of AngloGold and Ashanti Goldfields in 2004 the mine strives to achieve optimum extraction through an integrated Mineral Resource management process from geological modelling, resource evaluation to mine design and scheduling. The shear hosted gold deposit displays complex secondary shears of variable thickness and continuity. There is an ongoing process of changes taking place in the way that geological modelling and resource estimation is done. Recent developments include the use of computerised systems that support the whole resource management chain from resource modelling to reserve optimisation. The change in thought and technology now allows for targeting narrow veins previously ignored in optimisation and mine design since moving into mechanised mining. The increased knowledge and confidence in the resource models now allows for flexibility in mine design, selection of mining method and scheduling and extraction of the reserves. The focus area for change is the way the orebody is evaluated and extraction designed. Since 2005 major changes were made to the process. This paper considers the historical approach of resource management. It looks at the individual process changes and qualifying the way ahead.

Jan 1, 2008

By I Canbulat, J Emery, L Yao and C Zhang

This paper documents a process of data analytics and machine learning applied to coalmine roof convergence data. It follows a publication documenting the formation of the database. For each set of analyses Python scripts were utilised to extract data from an SQL database, with subsequent analyses also executed in Python, utilising open-source tools such as scikit-learn. Preliminary analyses with classic machine learning algorithms included multiple logistic regression, K-nearest neighbours, decision tree, random forest, support vector machine, kernel support vector machine, artificial neural network (ANN), naïve Bayes and multiple linear regression. Results indicated that relationships were complex and non-linear, with the artificial neural network most suitable. An ANN model was then refined through a standard process of hyperparameter optimisation and data augmentation to arrive at a final model. Due to the black box nature of the ANN further insight into how the parameters interacted was sought and found with Shapley additive explanations (SHAP values). SHAP values utilise Game Theory, where each input parameter or feature is a ‘player’ while the data set is the ‘team’. The SHAP value is the impact of each player on the target value, essentially establishing the contribution of each input parameter. The results from all analyses are delivered in the paper, together with insights, applications, strengths, and limitations of the methodology.

Nov 29, 2022

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By C W. Davis

Every diesel engine emits approximately 100 million nano diesel particles (nDP) per cubic centimetre of raw exhaust. Each nDP has a diameter of between 50 and 70 nano metres or 1/100th the size of red blood cells (diameter of between 6 and 8 microns). When inhaled, some nDP pass through the lungs and penetrate all body tissue [1]. Europe and North America have recognised and are addressing the long term health problems posed by nano diesel particulate matter (nDPM) across their societies [2.3]. Australia has been slow to recognise the issue, at both a societal and mining industry level. There are chronic health effects for every underground miner and serious legal issues for mining companies with increasingly stringent Occupational Health and Safety legislation being implemented at a state level across Australia. This paper will review progress within Australian society and more particularly the underground hard rock mining industry, particularly in Western Australia (WA).

Mar 15, 2021

With the sinking of the No. 3 Shaft and the erection of a changehouse nearby, a sub-brace level structure was provided incorporating a time office, underground foremenÆs office and lamp room, in conjunction with a covered walkway, ambulance room, fire station and waiting brace.

Jan 1, 1957

By J Loeb, D Thornton

Blast movement measurement is a key component of grade control, enabling mines to carry all of the precision involved in locating ore blocks, through a chaotic blast, to production. A monitoring system was developed about ten years ago so that mine operation personnel can measure three dimensional movement in every production blast. Research has shown that blast movement is always highly variable with a significant non-deterministic component. The consequence is that modelling will be inaccurate and therefore optimal ore recovery can only be achieved by direct measurement of blast movement.Three dimensional movement vectors are measured at discrete locations in the blast. If blast movement is only measured at one location in a blast pattern, data is severely limited and has all of the inherent inaccuracies of modelling a variable population. It is intuitive that the accuracy of defining the post-blast ore block mark-ups are proportional to the number of movement measurement locations, however increasing the number of monitoring locations causes increases to the direct operating costs of the mine.A cost-benefit analysis is used to explore the optimal number of monitoring locations. Using the method described in this paper, an automated selection of the number and location of blast movement monitors are analysed against the value of recovered ore compared to the control, for each trial.CITATION:Loeb, J and Thornton, D, 2014. A cost benefit analysis to explore the optimal number of blast movement monitoring locations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By A S. Derrington

In some parts of Australia, mine air cooling may not be needed until a depth of 1300 m below surface is reached. In other locations, it may be essential at a depth of only 300 m below surface. The reasons for these differences are multifaceted. This paper discusses the main factors and describes a simple method to assess whether or not mine air cooling will be required. The method uses a graphical relationship that considers depth below surface, geothermal gradient, surface climatic conditions and directness of the mine intake routes. This relationship has been developed, tested and refined over a period of more than ten years using data collected from most of Australia’s deeper metalliferous mines. The method provides a ‘first-pass’ indication of whether more detailed cooling studies may be needed. Perhaps more importantly, the method’s underpinning by benchmarking against other mines improves confidence in the assessment results. Like any empirical method, the context must be understood and this aspect is also discussedCITATION:Derrington, A S, 2014. Will your mine require cooling?, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 181–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By D Laskovski, T Nguyen

Flotation surveying can be an extremely powerful means of determining opportunities for circuit optimisation and benchmarking. The type of survey employed depends heavily on the nature of the information required from the survey. It follows then that the type of survey determines the type of samples required; however, regardless of the type, the success or failure of a survey is often dependent on the correct used of appropriate sampling techniques at each sampling point. For a successful flotation plant survey it is vital that the correct samples be collected at the correct time in respect to the feed and each other. This paper discusses the current best practice sampling methods used in flotation surveying and discusses in detail the ideal sample masses based on theoretical analysis. Comparisons with JKTech’s database of real plant operations will then be made.CITATION:Laskovski, D and Nguyen, T, 2014. An investigation of current flotation survey sampling, in Proceedings Sampling 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By G Byrne, A Bowden

There is often a difference in opinion about the allocation of risk in the establishment of mine closure bonds or financial assurances. From the State’s perspective, protection is needed to ensure that the broader community is not left with the liability of properly closing a mine in the event of a default by the mine operator. Such a default might occur where an operator decides to abandon a site, perform incomplete rehabilitation, becomes insolvent or claims limited liability. On the other hand, mine operators who can demonstrate a strong financial position plus a record of social and environmental commitment and performance, argue that there should be some recognition of this in setting a bond that is less than the full cost of early closure. They argue that a mine rehabilitation bond based on the full cost of early closure is overly conservative and ignores the actual risk of the operator being in default. This paper examines an approach that incorporates the risk of default into the establishment of mine closure and rehabilitation bonds. CITATION:Bowden, A and Byrne, G, 2018. Mine closure bonds (financial assurances) – the ‘how much?’ conundrum, in Proceedings Life-of-Mine 2018, pp 32–34 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By R Peiffer, L van Wyk

The Port of Port Hedland is the largest bulk export terminal in the world and is one of Australia’s most important pieces of economic infrastructure. BHP is the largest Port user to support the export of iron ore products from mines located within the Pilbara region of Western Australia (WA). BHP’s priority is the safety and well-being of its workforce and the communities where it operates. In a recent regulatory application to increase export capacity, BHP committed to the deployment of wind fences to reduce wind erosion from stockpiled ore. Wind erosion from stockpiles was identified through inverse modelling as the most significant dust source compared to other sources such as stackers, reclaimers, shiploaders and transfer stations. The primary cause of dust emissions from stockpiles is dust lift-off during high wind conditions. BHP proposed the installation of wind fences across its Port Hedland operations, targeted at reducing emissions from wind dependent sources, primarily stockpiles, by reducing the wind speed downwind of the wind fence. Modelling predicts that installation of the wind fence will significantly reduce emissions from stockpiles, particularly at BHP’s western operations (Finucane Island). To be effective in shielding stockyards and reducing wind speeds, the wind fences are located upwind and as close as practical to the open stockyards. BHP’s wind fence design incorporates learnings from other existing installations and has been tailored for Port Hedland’s cyclonic conditions. The wind fence will be higher than the stockpile height, with a mesh porosity of approximately 50 per cent. The mesh porosity allows some of the wind to pass through the mesh. This reduces the wind turbulence downstream of the wind fence, as opposed to a solid wind fence, which increases downwind turbulence, resulting in increased dust.

Sep 18, 2023

Selective leach analytical techniques applied to surface geochemical samples in the search for deeply buried mineral resources gained popularity in the late 1990s. Several commercial assay laboratories introduced their own selective leach methods, adding to the few established commercial methods at that time. Many of these laboratories promoted their methods with orientation data showing favorable responses to both precious and base metal mineralisation, concealed beneath extensive thicknesses of overburden. However, many explorationists remain confused about the utility of these geochemical methods. This confusion is due primarily to the lack of objective orientation surveys over significant mineralisation, comparing all commercially available selective leach methods and to the lack of a creditable theory explaining the formation of these selective leach anomalies. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. An orientation survey was designed to fill the first void û an objective survey over significant mineralisation. With the help of 17 mining companies and assay laboratories, an orientation survey was conducted over five significant covered gold deposits in Nevada, USA , representing over ten million ounces of gold. Hopefully the results of this survey will help provide fuel for those working on the second void û a theory to adequately explain the formation of these selective leach anomalies.

Jan 1, 2008

By Grano S. R, Lauder D. W

Investigations on the oxidation behaviour of chalcocite and its rejuvenation by hydrogen sulphide ion have been undertaken. Chalcocite oxidation was measured using X-ray photoelectron spectroscopy (XPS), zeta-potential and by dissolution in et

Jan 1, 1997

By J J. Van Wijk, A R. Penney

Successful management of geotechnical risk at a mining operation is more than just having a good ground control management plan or using advanced numerical modelling and the latest monitoring technologies. The fundamental requirements for effective geotechnical risk management include identification of potential failure modes, identifying and implementing appropriate controls, and demonstrating the effectiveness of those controls. Effective geotechnical risk management requires an integrated approach by confirming that appropriate risk management systems have been identified and implemented (management plans, procedures etc), and that these systems are executed consistently in the field across all working areas. Development of a thorough integrated auditing process executed by an experienced team of technical subject matter experts with substantial operational knowledge, provides a more complete picture of catastrophic hazard management. Following consistent evaluation criteria allows benchmarking of systems and implementation compliance between the sites being audited, and the results can then be ranked against other operations in an industry database.

Nov 29, 2022

By M Bettison, R Wright, N Taylor

The primary mine planning focus during early study phases of future mining projects is Life of Asset ore production and grade quality, this will always be the situation. While waste schedule optimisation is generally considered in the latter study phases nearing execution for a limited number of schedule periods only and not a true optimisation considering all attributes such as waste destination location, design, cycle time and closure. This can be particularly applicable in large multi-pit bulk mining operations where one approach to meet Life of Asset ore tonnes and grade targets has been to maintain pit development flexibility resulting in large open pit areas and substantial expit Overburden Storage Area (OSA). The value opportunity is to develop a Life of Asset waste schedule source-to-destination optimisation prior to mine development considering all applicable attributes and routinely review throughout the Life of Asset taking account of improved ore and waste knowledge.CITATION:Taylor, N, Wright, R and Bettison, M, 2018. Utilising mine planning to deliver closure landforms through productive movement, in Proceedings Life-of-Mine 2018, pp 96–99 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018