Search Documents

By Takasaki Y, Ohzeki S, Hotta H

TO measure high temperature properties of blast furnace burdens ( the change of gas permeability accompanied by contraction, soft- ening and melting ) which govern the gas flow and its distribution, a series of experiments were carried out under simulated blast furnace conditions, using sinter, acid pellets and self -fluxing pellets. 1) The high temperature properties are affected by the ore's reducibility ( up to 1000 -1200¦C ), and the composition, and volume of gangue before reduction. Generally, the burde- ns with high basicity ( Ca0/Si02 ), high reduc- ibility and low volume of gangue have good high temperature properties. Good high temperature properties are : a high temperature at which the gas permeability rapidly decreases, a high melting point and a low maximum pressure drop. 2) Using acid pellets, slow-down of red- uction rate occurs around 1000¦C because the pellet forms a dense metallic shell, while its slag core, resulting from a FeO, Si02 and A1203 reaction, has a lower melting point. 3) The addition of MgO sources improves high temperature properties both of sinter and Pellets.

Jan 1, 1980

By P Gehrke, S O’Gorman

The precise measurement of NO2 was historically difficult in road tunnels, hence criteria and design analysis was based on converting from NOx concentrations via a set NO2:NOx ratio. The reliable direct measurement of NO2 is now possible, however design analysis is still dominated by emissions tables and formulas specified in terms of NOx. For converting from NOx to NO2 in a road tunnel environment in Australia, the ratio has typically been assumed to be ten?per?cent. This has generally been based on the recommendation in PIARC (2000) and on the ‘average’ value cited in PIARC (1995).Determining this ratio is important as changes in engine technology and in-tunnel pollution criteria along with improvements in CO and particulate emissions control, may mean that NO2 will become the driving factor for future ventilation requirements. Correct selection of this ratio can directly impact the ventilation capacity and system design.Recent research has indicated that choosing a constant ratio of ten?per?cent for all tunnels may not be appropriate. The in-tunnel ratio has been estimated to be as much as 20?per?cent to 30?per?cent and depends on the location in the tunnel, the type of ventilation system and the traffic/fleet characteristics. This paper discusses the effect of some of these parameters on the NO2:NOx ratio in road tunnels.The findings indicate that the ten?per?cent upper limit on the NO2:NOx ratio in PIARC (2000) may be a conservative value for design purposes for longitudinally ventilated road tunnels of typical length in Australia. A value of seven?per?cent to eight?per?cent may be more appropriate in some circumstances. However, the value chosen will depend on the specific tunnel in question and the confidence in traffic conditions expected. Values above ten?per?cent may be encountered for short periods but usually when the NO2 levels are low.CITATION:O’Gorman, S and Gehrke, P, 2014. NO2:NOx ratios in Australian road tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 95–102 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D A. Deglon

Solids suspension is important in the design and operation of mechanical flotation cells, and is a necessary precondition to particle collection. Most of the fundamental hydrodynamic research that incorporates some aspect of solids suspension was done by Arbiter, Harris, and co-workers, or Schubert and co-workers. However, a need for research into solids suspension in mechanical flotation cells exists, since very little has been done since the late 1980s; a time that also coincides with the advent of round mechanical flotation cells and the subsequent dramatic increases in maximum flotation cell sizes. In this work, concentration profiles and critical impeller speeds, Njs, were measured in a 0.124 m3, round cell fitted with a 0.150 m, Bateman impeller mechanism. Two solids size fractions (75 - 106 and 150 - 250 ¦m) were tested, in ungassed and gassed conditions (JG = 0, 1 cm/s) and at various impeller speeds (300 - 900 rpm). The effectiveness of solids suspension was quantified in three ways in terms of extent of off-bottom solids suspension, suspension height (extent of solids distribution), and variation within the solids distribution, which together present a complete quantitative picture of solids suspension and distribution within the cell. Consistent trends were found when these effectiveness criteria were considered against relative impeller speed, in terms of percentage of critical impeller speed, N/Njs. Off-bottom solids suspension is complete at or above 100 per cent of Njs, with significant sedimentation occurring as the impeller speed drops below 60 per cent of Njs. Suspension heights consistently reached a level equivalent to 90 per cent of the tank diameter at the critical impeller speed, and dropped off significantly as N/Njs dropped below 60 per cent. The variation in the solids concentrations within the sampled profiles showed consistent trends in two-phase but not under three-phase conditions. The paper concludes that the critical impeller speed, Njs, commonly used in the design and operation of standard stirred tanks, is a very useful solids suspension benchmark for describing all aspects of solids suspension in mechanical flotation cells and should be correlated to system conditions.

Jan 1, 2005

By C Armstrong, B Wentzinger

Upstream embankment raises often represent the lowest cost option for increasing the capacity of tailings storage facilities (TSF), but also pose the highest stability risk due to constructing on top of previously deposited tailings.This paper presents an overview of key aspects in the geotechnical investigation and design of upstream raises and some recent lessons learnt from experience across a number of TSFs in Australia. A summary of recommended field investigation and laboratory testing methods is provided with a focus on collecting quality information for design purposes. A strong focus is given in developing an accurate assessment of pore water pressures, which, if not correctly understood can have disastrous consequences on tailings strength parameter interpretation and wall stability assessment in static and post-seismic conditions.The assessment of the contractive or dilative shearing behaviour of the tailings material and rigorous interpretation of design characteristic values are presented. Some comments on stability analysis options and proposed methodology are also provided.CITATION:Wentzinger, B and Armstrong, C, 2018. Lessons learnt in geotechnical investigation and stability analysis for upstream tailings storage facility raise design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 333–348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By D Johansson, A Nordqvist, D Mihaylov, N Petropoulos, M Wimmer

The flowability of the caved rock masses in the sublevel caving (SLC) mining method is of great importance. During the blasting process of a SLC-ring, the caved rock mass in front of the ring is compacted. As a result of this compaction, the mechanical properties of the fractured rock masses change, for example void ratio, angle of internal friction and structure of the compacted material. The changed mechanical properties of caved rock mass and recent blasted material can influence the mobility of the material, which could result in blockage of the flow path of the material. The identification of the involved mechanisms in this process can be done after a series of tests in different scales. However, there is no available equipment for dynamic measurements during blasting, ie velocity and displacement of the burden and in the caved masses. This study focuses on the development and laboratory evaluation of a measuring system that can be installed in a borehole. The first trial was carried out in a pillar, where two blastholes had been drilled (9.5 m) parallel with the drift and two measuring holes (16.5 m) were perpendicular to the drift. Two measuring systems were installed in the measuring holes. Some preliminary tests were carried out to find suitable initiation procedures for the emulsion explosive. Applicability and robustness of the developed measuring system were also evaluated. In addition to these tests, an expandable cement mixture was developed to firmly anchor the measuring systems in the boreholes. The measuring system consists of an anchor, armoured cable in a pulling tube and a protective case. The anchor is equipped with uniaxial and triaxial accelerometers. A potentiometric measuring system for displacement up to 2 m is installed at the end of the pulling tube and connected to an extendable spiral cable. All sensors are connected to a data acquisition system (DAS). Both measuring systems have their own DAS to acquire data in case of failure of one of the systems. The measuring system was tested in laboratory conditions with impact velocity up to 10 m/s. It was proven to be functional and gave reliable results.CITATION:Petropoulos, N, Mihaylov, D, Johansson, D, Wimmer, M and Nordqvist, A, 2015. Design of equipment for dynamic burden measurements, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 493–500 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By R Burke, G Ramage, C Donnelly

Over the decades, Redpath has undertaken a multitude of tunnelling and underground excavation projects for civil and mining clients both domestically and internationally. These projects have been undertaken through varying strata conditions with differing excavation methods in remote locations and in central business districts.With the recent turbulent nature of the global financial environment, project drivers have been challenged with the emphasis being placed on methods to gain early access to orebodies, rapid development techniques, lower capital costs and reduced labour requirements to name a few.A number of mining companies seeking to achieve these objectives have commenced the journey to better understand the operational constraints, challenges and opportunities that may be available with the use of alternative excavation methods.The development of safe and effective alternative excavation methods that comply with both domestic and international mining legislation and regulatory requirements is a challenge the industry needs to embrace. Given the current cost pressures being faced by the Australian mining industry, some alternative excavation methods offer the potential for longer term sustainability and rapid development of resources.More recently work has been undertaken on a project that challenged the norm and implemented an alternative excavation method with the use of an excavator with a rotating drum cutter head.This paper will review this recent project and provide technical and operational insight into some of the challenges faced in implementing an alternative excavation method in the metalliferous industry.CITATION:Donnelly, C, Ramage, G and Burke, R, 2014. Challenging the norm – alternative excavation method in mining, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 187–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By J A. M Luz, A T. Bernardes

HukkiÆs law is an empirical law, which does not take into account several events of energy loss during the fragmentation processes. Since experimental results are very difficult to obtain, for a large range of fragment sizes, the verification of the law is very difficult. The relation between fractures and fragmentation processes with fractal geometry was proposed some decades ago. Empirical laws known in this context show basic features of fractal geometry, mainly self-affinity and power law behaviour. Thus, in this work a model was developed to simulate the fragmentation process and to check the relation between energy consumption and fragment sizes. The model is represented on a regular lattice. Links can represent pathways for fracture processes. The events of fragmentation have energy given by a probability distribution function. In the model there is no mass loss. Propagation of fractures occurs as self-avoiding random walks on the regular lattice.

Sep 26, 2011

By T Goswami, G Brent

In response to concerns over greenhouse gas (GHG) emissions and an imposed cost in some jurisdictions, many mining houses have committed to reductions in their GHG emissions. However, mining faces particular challenges in this regard, notably from increasing strip ratios. Furthermore, mining activity around the globe is not expected to decrease in the foreseeable future as mineral demand is driven up by the aspirations of rapidly-developing nations. Novel approaches will thus be needed if any reductions in energy consumption and GHG emissions of mining are to be achieved.This paper presents some directions for the mining industry to pursue in reducing their GHG impact, focusing on the difference that blasting methods can make. Importantly, large productivity and revenue gains can also be realised from these methods.Key directions considered here include optimising resource recovery and quality through:reducing coal damage and loss from throw blastingrecovering thin coal seamsproducing cleaner coal with less dilution.Blast design can also significantly improve the productivity of surface mining by:improving muck pile shapingimproving mine equipment productivityimproving scheduling.We show how a particular blasting method can eliminate coal loss in overburden throw blasting and can lead to large increases in coalmine profitability. Thin seams that were previously wasted can also be recovered with this method. Furthermore, the method has been implemented to combine several separate drill and blast cycles into a single cycle, leading to productivity gains.An illustrative example is given to show how increased coal recovery can increase revenues and more than offset any potential GHG emissions liabilities. Overall mine energy and GHG emission intensities can thus be reduced.CITATION:Goswami, T and Brent, G, 2015. Blasting approaches to increase mine productivity and reduce greenhouse gas emissions in surface coal mining, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

Western Australia has often been referred to as the fly-in, fly-out capital of the world. Fly-in, fly-out is a commonly used practice in Western Australia due to the geographic size and isolated location of the vast resource projects. In the State today, approximately half of all resource sector employees operate on a fly-in, fly-out basis, with a minority utilising drive-in, drive-out arrangements. fly-in, fly-out arrangements are generally beneficial from a sustainability perspective, delivering significant economic, social and environmental benefits to regional communities, the State and nation as a whole. Skills shortages and labour supply issues mean that the industry will be required to discover new ways of attracting and retaining employees, one of which is the adoption of fly-in, fly-out work journey arrangements. By 2015, the minerals sector in Australia will need to employ 70 000 more employees than it currently employs to achieve predicted increases in output. Of the 70 000 additional employees required, 42 000 will be required in Western Australia, almost 15 000 in Queensland and approximately 5000 in both New South Wales and South Australia. The fly-in, fly-out lifestyle as a preferred method of employment should be recognised as a valid lifestyle choice by all members of the community, offering a profound improvement in the quality of life for large numbers of employees and family members. It should be acknowledged that whilst fly-in, fly-out is a preferred option for many companies and their employees, individuals who make a choice to engage in fly-in, fly-out must balance the difficulties associated with the work û isolation and separation from family and friends û against the economic and lifestyle benefits that the work offers. This paper aims to illustrate the significant steps that the resources sector has taken to facilitate the fly-in, fly-out choice by ensuring that the commute option is a safe, attractive and manageable work journey arrangement.

Jan 1, 2008

By R Schlueter, H Mischo

The mining industry is facing a variety of geological, technological and social challenges. Future deposits show a general tendency towards increasing depth with complex ores and decreasing grades. One promising approach to deal with low-grade ores is bioleaching in the form of heap and dump operations. Bioleaching is already a state-of-the-art technique, especially for the extraction of copper from sulfide ores. The next step in the development of this technology will be its application as an in situ technology. First attempts to adapt this technology in underground mining in the form of stoping and block caving have already been made. Both methods have to be carried out adjacent to conventional mining operations and therefore require much effort regarding drift development as well as extraction and transport. The adaption of bioleaching as a borehole mining method is the next step to establish an innovative in situ technique to meet future challenges.The Freiberg University of Mining and Technology established the Biohydrometallurgical Centre for Strategic Elements (BHMZ) to foster interdisciplinary research along the whole biohydrometallurgical process chain. In general, 13 different university institutes and several associated groups with about 30 PhD students are mainly focusing on the extraction of indium and germanium from deposits, tailings and recycling material. One of the core projects within the BHMZ is the design and implementation of an underground in situ bioleaching testing facility.This paper demonstrates the potential of in situ bioleaching under technological aspects. Furthermore, different conditioning methods to increase the permeability of the orebody will be explained, and the BHMZ’s underground testing facility will be presented.CITATION:Schlueter, R and Mischo, H, 2015. Potential and applications of underground in situ bioleaching, in Proceedings Third International Future Mining Conference, pp 205–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L Clarkson, D Williams, P Redcliffe, F van der Wal

This research presents a snapshot and insight into the trends, patterns, and common considerations identified in the current standing of real-time tailings dam monitoring practice. Based primarily on information derived from concurrent research by the author (in form of a Catalogue of Real-time Instrumentation and Monitoring Techniques for Tailings Dams), challenges and opportunities when transitioning to a real-time monitoring system are discussed. Learnings and key considerations between different monitoring approaches are explored, including themes of limitations and advantages that were observed consistently through global supplier feedback.

Jul 1, 2021

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Somerville M, Muray A, Bocking M

Australia has an extremely large total hot dry rock (HDR) resource above a depth of 5 km, equivalent to 7500 times its present annual energy consumption, of which 80 per cent underlies the Great Artesian Basin. The resources most likely to be exploited first are those residing in homogeneous granitic bodies beneath sedimentary basins containing insulating rocks such as shales and coal measures. In the Sydney Basin south of Muswellbrook, an area of high geothermal gradient corresponds to a gravity low thought to be a buried granite body at a temperature of possibly 250¦C. This locality is suspected to have the ideal geological characteristics for Australia's first hot rock test facility. Australia's high HDR potential is possibly unique in the world, in that the potential sites satisfy four independent, geological conditions, each considered as favourable for the creation of a resource, and for the ease of extracting that resource. They are: ò Higher crustal heat generating capacity than that of normal continental crust. ò Much of the Australian continent is covered by sedimentary basins which contain a high proportion of shales and coal measures that have low thermal conductivities, thus providing an insulating blanket for the heat being generated beneath. ò The sedimentary basins are in many places underlain by large untectonised granitic bodies that are not only a major contributor to heat generation, but also ideally suited to the establishment of HDR reservoirs. ò The crustal shortening stress field that is found in the majority of the Australian continental crust results in a vertical minimum principal stress orientation which should result in the development of favourably oriented horizontal stimulation cells necessary for maximising an HDR resource.

Jan 1, 1995

This paper reviews recent advances in geophysical tools for mineral exploration. It does not restrict comments to methods which are usually applied in the tectonically active belt surrounding the Pacific Ocean, where geophysics has often been secondary to geological prospecting (eg visual recognition of surface alteration) and drainage geochemistry; but considers geophysical tools applied to a broader range of both deposits and terrains. For example, the subdued topography of much of Australia and Canada has lent itself to the development and extensive application of airborne methods. In Australia, deep weathering and transported cover have necessitated the use of geophysical methods to not only detect anomalies but also to map and understand basement geology. This same weathering has caused specific problems, particularly for electrical methods, but recent improvements in instrumentation, processing and visualisation have largely overcome them. A great deal of geophysical data is now being collected by government agencies, often from the air, and made readily available to explorers. In several Australian states it is free, often on line, and in almost all cases it is relatively cheap. These regional data sets are often augmented by more detailed local surveys in areas of interest. Although æanomaliesÆ are still important much more is being done with the high quality data which is now available The results are used for geological mapping, to test geological hypotheses, to construct detailed 3D geological models and, together with fluid flow modeling, to predict optimum locations for mineralisation.

Jan 1, 2004

By D T. Ribeiro, J F. C L Costa, J C. Koppe

Drilling and sampling are responsible for most of the costs during mineral exploration, especially in multi-elements and polymetallic deposits, such as iron, manganese and bauxite deposits. On these deposits, often it is necessary to estimate multiple attributes at several granulometric fractions, ie distinct particle sizes. This paper investigates the effect of sampling at a close spacing grid only the head grades for the multiple chemical species in iron ore deposits. The remaining required data at the various grain sizes are sampled at a sparse grid. The derived geological model is checked for precision and accuracy comparing the output obtained against a model obtained using a complete isotopic data set including head grades and chemical analysis at each granulometric fraction analysed at all sampled positions. Among the several tested alternatives, the best procedure for dealing with the posed problem involved utilising the correlation coefficients between the grades at distinct fractions to obtain an isotopic database prior to interpolation. Cokriging was the method used, based on the intrinsic coregionalisation model. Estimates were obtained with the quality needed for the proposal of the study. Results showed that at least 50 per cent of the blocks were estimated with errors less than ten per cent relative to the grades obtained at the reference model, using only 15 per cent of the granulochemical data employed to obtain the reference model. The methodology also preserved the correlations between the attributes in their several granulometric fractions on the estimated model.

Sep 26, 2011

Nordberg has conducted extensive research, during 1982-85, on the effects of cone crusher variables such as speed, throw and cavity design on the productivity of the crushers. Simultaneously, Nordberg's engineers have developed advanced design and testing techniques that ensure efficient and reliable crusher designs. Combination of this knowledge has resulted in a design of the MPI000 (1000 hp) crusher which fits on the existing 7ft Symons foundation and yet is capable of producing twice the ton- nage of the 7ft. In this paper the development of the MP1000 crusher and its performance compared to the 7ft heavy duty and super heavy duty crushers will be discussed. Also, substantial cost savings resulting from the application of such a high performance machine will be presented.

Jan 1, 1988

Since the earliest recorded prospecting of the 1860's mineral exploration and mining in Fiordland has been discouraged by the formidable physical difficulties presented by its isolation, extremely rugged relief, treacherous coastal waters and generally unfavourable weather conditions. Government assistance was often sought by the miners and prospectors but little, if any, support or encouragement was received after the initial period. During the 1840's decorative marble was quarried at Caswell and Dusky Sounds. A prospector discovered and attempted to mine copper sulphides to the north of Dusky Sound (Parks Mineral Beds) and near Mt Solitary. A small Pb, Zn, Cu, Ag, Au bearing quartz reef was discovered and driven on in the granite coast line of Preservation Inlet (Bradshaws Reef) and the ore roasted on site. Alluvial and quartz lode gold was discovered at Preservation Inlet in the 1890's and led to the recorded recovery of 11 000 oz of mainly lode gold. Falloff in grades with depth, thinning and splitting of the reefs and the high mining costs at this location led to a virtual abandonment of the field by 1906. In the late 1950's and early 1960's the geology of Fiordland was mapped by the Geological Survey at 1:250 000 scale, but field work was largely confined to the shore lines of the coast and fiords. In view of the physical difficulties it is not surprising that mineral exploration and mining up to 1970 was limited to the scant attention outlined above.

Jan 1, 1977

By Beattie T. A

The ability of explosives to fragment rock has been assessed in small scale trials at the Granite Rock quarry, Baimsdale, Victoria. Three 65 mm diameter holes were fired simultaneously in a five metre bench, and the rock collected, screened and weighed. The mass of fines increased as the explosive strength increased in the series 30(10 ANFOPS

Jan 1, 1990

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015