Search Documents

By P Hagan, S Wang, D Li, B Loh

A study was undertaken to quantify the differences in performance between a full-length encapsulated cable bolt and a partially encapsulated cable bolt. Much research has been reported on the differences in cable bolt design and operational parameters such as borehole diameter and grout type with much of this based on the Laboratory Short Encapsulation Pull Test (LSEPT). However, there is a gap in knowledge surrounding the effect of anchorage length on load transfer and cable bolt performance particularly with respect to the role of the bulb in modified cable bolt designs. The objective of this study was to expand the existing knowledge base of cable bolt performance with the intent of developing a revised design criterion. Alongside a comprehensive review of current cable support theory, design and practice, a series of pull tests was undertaken to compare each anchorage method using a high capacity modified cable bolt. The results serve to confirm earlier work on fully encapsulated anchorage. Both the peak load capacity and stiffness of the fully encapsulated cable bolt were nearly double that of the partially anchored cable bolt. When the tests were repeated in an oversized borehole, while there tended to be more variation in performance, there was little significant difference in the mean results. In addition to anchorage length, there are other factors that contribute to cable bolt performance including in order of sensitivity: embedment length, water-to-cement ratio of the grout, type of grout and borehole diameter. CITATION:Loh, B, Hagan, P, Li, D and Wang, S, 2018. A comparison of the performance of fully versus partially encapsulated cable bolts based on laboratory-scale testing, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 291–302 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By K Nakashima, K Aya, T Sumita, N Saito

Electro slag remelting (ESR) is one of the methods used to produce high-cleanliness steel. In the ESR method, the product steel electrode is immersed in flux, and the electrode is melted by the Joule heat of the flux generated by high current. CaF2-based melts are mainly used as fluxes, but the electrical conductivity of CaF2-based melts varies widely among researchers and measurement methods. Therefore, this experiment aims to measure the electrical conductivity of CaF2-based melts based on the van der Pauw-Ohta method, which does not require the cell constant that is a fundamental error factor in electrical conductivity measurement at high temperatures. The measurement temperature was set at 1450–1600°C, and dehydrated Ar flowed through the furnace at 200 mL/min. Electrodes were fabricated by Pt-30mass per cent Rh alloy, and the electrodes were connected to an impedance analyser using a four-terminal probe. The electrodes were immersed in the melt, and the impedance and phase angle were measured by AC frequency sweep (50 Hz to 200 kHz). The electrical conductivity was then calculated by utilising the impedance’s real part values when the impedance’s imaginary component was zero. The electrical conductivity showed a positive temperature dependence. The electrical conductivity of 60(CaO⋅Al2O3)-40CaF2 melt increased with increasing temperature but was found to be roughly one-third of those of the previous studies. In the conductivity measurement of 60(CaO⋅Al2O3)-40CaF2 melt, the AC frequency with a phase angle of 0° was found to be different depending on the temperature and immersion depth. By sweeping the frequency, the impedance at the phase angle of 0° can be obtained, which enables us to measure the electrical conductivity more accurately.

Jun 19, 2024

By P Dare-Bryan

Many mines have an interest in improving fragmentation at their sublevel caving operations in order to produce better ore recovery, lower dilution and less overbreak. The primary requirement for the extraction phase is to understand and optimise the flow of the fragmented rock in the rings including interactions with the caved material. Rock fragment formation is critically controlled by the blasting phase and can potentially be improved by optimising the dynamic energy distribution throughout the ring through the crafting of explosive charging, priming position and initiation timing. The modelling of fragmentation and damage due to explosive loading of complete rings is inherently and irrevocably a three dimensional problem that is difficult to address. We have therefore initially utilised an analytical code to predict vector peak particle velocities and energies that are restricted to the plane of a ring. Dynamic energy distributions based on common timing and priming practice have been compared with other possibilities using conventional pyrotechnic detonators as well as initiation designs based on accurate electronic detonators. The energy distribution can be quite subtly tailored to increase energy in appropriate regions or to decrease energy in the brow region for example to potentially reduce instability and the probability of misfires. We have also recently developed the capability to efficiently model particle flow using four-sided polygonal elements. Despite the 2D limitations of such a model this results in more realistic fragment interaction and stacking than can be achieved using conventional rigid circular elements. Modelling of a typical sublevel caving ring utilising these elements activated by the correct dynamics offers considerable potential for understanding the influence of the blasting energetics and timing on the complex flow and extraction process.

Jan 1, 2005

By P A. Grossman, J H. Rubinstein, M Brazil

The installation of truck turntables at above-ground crushers has the potential to yield gains in efficiency and productivity by eliminating the need for the trucks to turn around and reverse up to the crusher to dump their loads. The benefits include savings in time, fuel consumption and tyre wear. In addition, having a smaller area near the crushers dedicated to manoeuvring the trucks can be a significant benefit at some sites. Safety is also enhanced using turntables.This paper describes a project with the Australian Turntable Company to develop software that generates near-optimal layouts for the paths taken by the trucks in the vicinity of the crushers when turntables are present or absent. The geometry of the paths is constrained by the turning radius of the trucks and by the boundary of the manoeuvring area. The software quantifies the benefit of installing turntables by generating a design for paths with turntables and comparing it with the layout in current or planned use by the mining company. Through the use of this software tool, a mining company can readily assess the benefits of using turntables at their site.CITATION:Brazil, M, Grossman, P A, Rubinstein, J H and Thomas, D A, 2014. Demonstrating efficiency gains from installing truck turntables at crushers, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 259–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By J Lombardi, M Weidenbach

"OZ MineralsÆ Prominent Hill copper-gold concentrator is located 650 km north-east of Adelaide, 130 km north-east of BHP BillitonÆs Olympic Dam operation and 130 km south-east of the regional township of Coober Pedy, in the Gawler Craton region of South Australia. The concentrator was built in 2008 and commenced commercial production in early 2009. The Prominent Hill concentrator is comprised of a conventional grinding and flotation processing plant with a 10 Mt/a ore throughput capacity, operating well over the design rate of 8 Mt/a. Increased throughput rates have seen a decreased water recovery from the tailing thickener due to operating above design. Subsequently, greater pressure was placed on the site water balance and bore field off-take rates due to increased evaporation losses from greater volumes of water reporting to the tailing storage facility. This resulted in a trade-off between water availability and milling rates as part of the operating strategy.Two projects were implemented to increase the tailing thickener underflow density, thus improving water recovery directly back into the operating plant, reducing water losses via evaporation and decreasing the reliance on the bore field system operating at maximum rates to maintain mill throughput. The two projects were: tailing thickener feedwell redesign implementation of the Manta Cube control system.This paper discusses the background, implementation and benefits attained from these two key projects. Combined they have allowed a two to three per cent increase in tailing thickener underflow density to be consistently achieved, which has allowed greater water recovery. As a result, the processing plant has been able to operate at higher throughput rates when required, with greater water availability in the process plant recirculating system and a reduction in occurrences of the plant being æslowed downÆ due to water supply shortfalls. Both projects have also delivered a significant reduction in flocculant usage.CITATION:Weidenbach, M and Lombardi, J, 2012. Tailing thickener operability and control improvements at Prominent Hill, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 137-142 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 29, 2012

By S Davidge, J Pile, R Schumann, E Kepe, W Stewart, M Ridd, B Rathi

Geographical constraints, including steep terrain and high rainfall, at the Ok Tedi copper-gold mine in PNG’s Western Province present Ok Tedi Mining Limited (OTML) with significant challenges in mine waste management. Waste management includes discharge of tailings into the local river system and storage of waste rock from the mine pit in waste rock dumps which erode into the river system. Copper bearing skarn mineralisation is associated with a massive sulfide (mainly pyrite) deposit. Consequently, waste rock and tailings can contain significant amounts of pyrite. Without appropriate management, these waste streams represent a risk of producing acid and metalliferous drainage (AMD) when discharged to the river system. Throughout the life of the project, OTML have developed evolving strategies to manage mine wastes and mitigate AMD.

Aug 2, 2023

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By Y Zhou, Y Liu, J-P Yang, P Wang, K Hu

"Large-scale mine reclamation has taken place recently in response to the implementation of mining regulations in China. Effective monitoring of the progress of reclaimed land is a critical procedure to assess the quality of reclamation program and to ensure that mining enterprises fulfill their reclamation responsibilities. The present paper reports a preliminary study that examines the situation of mine land reclamation monitoring. Based on the monitoring, some general requirements for mined land reclamation have been proposed, including: the monitoring should be systematic and comprehensive the monitoring should be adapted to specific local conditions the monitoring should be reasonably optimised via scientific methods and technology the monitoring should stick to a variety of national technical criteria.The aim of land reclamation monitoring is to evaluate changes of critical indicators closely reflecting the development trend of the reclaimed mined land, to develop or improve the criteria and technical parameters specific to the site, and to prevent secondary environmental degradation. Based on these requirements and aim, the monitoring should cover the progress of reclamation, establishment of vegetation and plant community development; and recovery of land and water quality in the reclamation area. Regulatory measures are proposed which would improve the work of mine reclamation monitoring in terms of regulation, organisation and financial support.CITATION :Wang, P, Yang, J-P, Zhou, Y, Hu, K and Liu, Y, 2012. The primary framework for the mechanism of the mine reclamation monitoring in China, in Proceedings Life-of-Mine 2012, pp 47-50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

By S Robson, T G. Blenkinsop, S C. Dominy

Golden Pig mine is in the central part of the Southern Cross greenstone belt within the Archaean Yilgarn craton. The mine has produced approximately 2.5 Mt of ore at 5.7 g/t Au to yield approximately 450 000 oz. The majority of gold mineralisation is hosted within extensively deformed and quartz-veined BIFÆs. In addition to the BIF-hosted mineralisation, an increasingly important part of the resource lies in the Taurus Lode, which is a N-NNW-trending amphibolite facies shear zone. The Taurus Lode lies within a continuous shear-zone that has a moderate to steeply WSW dipping foliation, and a mineral lineation of biotite, amphibole and pyrrhotite plunging consistently 10¦ S. Drive faces, subperpendicular to the foliation and lineation, consistently show evidence for syn-mineralisation reverse shear. Exposures parallel to the mineral lineation and perpendicular to the foliation reveal both sinistral and dextral asymmetries. These characteristics suggest that the vorticity axis of the Taurus Shear Zone is parallel to the mineral lineation, and that the simple shear sense is reverse. This geometry can arise when there is a major component of flattening across the shear zone, which may be due to interference between two adjacent granite domes. The BIF-hosted lodes plunge consistently 15¦ NNW coincident with the intersection of the axial planar cleavage of the regional folds and the Taurus Shear Zone. However, where the penetrative shear characteristics control the orientation and geometry of the mineralisation, oreshoots plunge SSW, parallel to the stretching and mineral lineations within the shear. The SSW plunge of strike extensive and laterally confined high-grade, economic ore shoots within the Taurus shear is fundamental to defining the economic mineralisation within this lode. Identifying the zones of maximum continuity and establishing the optimal position for future development will maximise ore extraction.

Jan 1, 2003

The Indonesian province of Papua is a remote jungle-clad region covering the western half of the mountainous island of New Guinea. Despite being relatively under-explored to this day,Papua is home to the greatest mineral success story of the 20th century. The Grasberg/Ertsberg minerals district atop the central dividing range contains the worldÆs largest reserve of both copper and gold (Freeport-McMoRan Copper and Gold, 2002). With large mines at Ok Tedi,Por gera and Lihir,and many well-delineated resources such as Frieda River,Wafi and Hidden Valley, neighbouring Papua New Guinea,the eastern half of New Guinea has enjoyed sustained exploration campaigns for gold and copper since the mid 1960s. The combined Grasberg and PNG exploration successes can be measured in terms of ounces of gold produced over the last decade versus available landmass,conf irming the island of New Guinea and surrounding islands as a world-class destination for gold explorers. Yet despite this obvious regional prospectivity and the profitability of the Grasberg operation, a sustained exploration effort in the Papua province in Indonesia has not been achieved. Periodic political constraints, poor infrastructure, high costs, operational challenges, social and environmental concerns and lack of immediate exploration success often impact exploration investment decisions. Accordingly a lesser number of mineral occurrences have been documented in Papua compared to those seen along tectonic strike in geologically similar Papua New Guinea.

Jan 1, 2004

By J Moffatt, T Payten, N Spooner, L Teixeira, L A. Balzan, G Wilkie, G Tsiminis

Fluorine is a penalty element due to its reactive nature. In acidic environments many fluorine minerals dissolve to form hydrofluoric acid (HF), changing processing conditions. When smelted HF can be released, causing negative effects to nearby people and the environment, as well as potentially damaging the smelter. Sale of ore with high fluorine levels elicit a financial penalty or are banned outright. Real-time sensors create the opportunity for instantaneous decisions on ore processing due to changing conditions. A fluorine sensor would allow rises in fluorine concentration in a processing stream to be flagged, and decisions on processing conditions or diversion to stockpile before processing could be undertaken. As fluorine is a light element, it is difficult to detect with in-field XRF devices and does not work well with PGNAA. There are currently no existing sensors to quantify the presence of fluorine in real-time, and thus decisions based on fluorine grade cannot be made at minute- or even hour-scales. Sensors designed to measure the presence of minerals that contain fluorine are a possible avenue to enable the real-time detection of this element. Mineral-based sensing may also give an added advantage of additional information about how the fluorine will react under different processing steps. The authors were given a grant under CRC ORE II (project number P1–005) to search for mineralspecific signatures suitable for real-time analysis. The work focused on novel regimes and applications of fluorescence as a means to detect specific minerals. The aim was to exploit fluorescence responses unique to minerals of interest in mining systems in order to produce sensors that address gaps in existing capability. After the successful discovery of signatures specific to two major fluorine minerals an additional grant (P1–014) was funded to develop the research into a prototype on-belt sensor, in partnership with Scantech International Pty Ltd. This paper details the development of a sensor package through multiple Technology Readiness Levels (TRLs) through collaboration with government/industry grant schemes, academics from university, and a sensor-focused Mining Equipment and Technology Services (METS) company. We give a brief description of the new sensor technique and provide a case study of multi-disciplinary collaboration.

Aug 24, 2022

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

By D J. Williams

The approach to the disposal and storage of mine tailings is slowly evolving. Tailings disposal has been based on minimising short-term capital and operating costs, with rehabilitation costs discounted by the application of a high discount factor in a net present value approach to accounting. This has led to the widespread adoption of surface tailings storage facilities (TSFs) to store slurried tailings delivered by robust and cheap centrifugal pumps and pipelines. Depending on the site climate, rate of rise of the tailings, nature of the tailings and the extent to which supernatant water is removed from the surface TSF, the tailings may or may not dewater, densify and gain strength. High rates of rise of dilute tailings to a facility used to store both tailings and supernatant water results in a wet, low-density, soft tailings deposit that not only occupies a large storage volume but also presents rehabilitation difficulties. A low tailings density results in high containment wall costs, very high rehabilitation costs and a low potential for future land use or ecological function. Overall, the cost of slurried tailings disposal, thought to be low, is actually high. However, low rates of rise, even of dilute tailings, in a dry climate with efficient supernatant water removal can produce a dewatered, high-density, stiff tailings deposit that may occupy a large footprint but to shallow depth that is relatively easy to rehabilitate. There are advantages in dewatering tailings in the processing plant to recover process water and chemicals, facilitate tailings disposal in a more solid form and facilitate rehabilitation. However, the cost of dewatering in-plant can be high, and the process water may not lend itself to reuse. There are also advantages in removing supernatant water to facilitate solar and wind drying of exposed tailings, although water is lost to evaporation and the dried tailings may best be harvested prior to inundation by fresh tailings or rainfall run-off. This paper discusses the background and trends towards the elimination of conventional surface slurried TSFs, with examples presented of the management of black coal and other tailings, including those that are clay mineral-rich.CITATION:Williams, D J, 2015. Towards the elimination of conventional surface slurried tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 11–24 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

Batch centrifugal gravity concentrators have become standard equipment in gold grinding circuits for recovery of gravity recoverable gold (GRG). The downstream benefits of installing a gravity circuit are well understood, and in general, if there is a reasonable amount of GRG in the ore, a gravity circuit is usually installed. The benefits of gold gravity recovery have also been well documented, with a large database of successful case studies. As well, predicting production scale gravity recovery results ahead of installing gravity has become a common practice. The missing link between lab and full scale has always been the ability to predict the recovery benefit of installing gravity ahead of actually doing so. Being able to predict the recovery benefit in advance would help an operation in assessing the economic benefit and help justify the capital costs of the gravity circuit with much less uncertainty.

Aug 1, 2010

By B Chapman, B Gaida, L Drowley

The 372 MW Ulu Jelai Hydroelectric Project is a peaking power scheme located in the Cameron Highlands, Malaysia. The main features of the project include an 84 m high roller compacted concrete dam; two weirs which divert flows from adjacent catchments via transfer tunnels into the main reservoir; an underground power waterway; and an underground power station complex comprising three large caverns with connecting tunnels approximately 240 m below surface level. The project includes approximately 25 km of tunnels excavated in fresh granite rock mass with some distinct shear zones of weaker material. The majority of the tunnels are being excavated using drill and blast, with the two transfer tunnels being excavated with a tunnel boring machine (TBM).This paper focuses on the design and construction of the Telanok underground power station complex and also some aspects of the design for the headrace tunnel. Topics covered include geological site investigations including in situ measurements of rock stresses; development of a geological model and parameters for rock support design; three-dimensional modelling to assess interactions between the caverns to optimise rock support; design of a rock anchored crane beam; construction of the caverns and design of the unlined headrace tunnel taking into account hydraulic jacking and operational pressure fluctuations.CITATION:Drowley, L, Gaida, B and Chapman, B, 2014. Design and construction of large caverns in granite – Ulu Jelai Hydroelectric Project, Malaysia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Yang

This paper presents a fragmentation model for large production blasts in an open pit or underground environment. The paper shows that the particle velocity is directly related to pressure, strain, and strain rate and so it can be considered as driving force and mechanism of rock fragmentation. This is supported by the fact that a vibration with a larger peak particle velocity (PPV) generates larger disturbance in rock and so finer fragmentation or more blast damage than a low PPV. The crack distribution in rock from impact is based on findings from previous researchers (Seaman, Curran and Shockey, 1976; Liu and Xu, in press). The fragmentation size is calculated at three-dimensional grid points within a blast. The fines and oversized blocks are calculated explicitly – the fines generated close to blastholes and big blocks far from boreholes are modelled naturally. The multiple blasthole fragmentation (MBF) model takes surveyed irregular geometry of the free face of a blast as the calculation boundary. The MBF can model fragmentation with over one million grid points. Examples of the model’s field comparison are also included.The PPV at a calculation grid is estimated based on the same approach used for the near field non-linear vibration model (Yang and Scovira, 2007). The method is based on the dominant charge for a calculation grid point, non-linear charge weight superposition within a charge and from multiple charges, strain wave broadening, and amplitude attenuation with distance from a charge segment. The blasthole confinement affected by earlier firing charges is also taken into account.The MBF model inputs from blast design, such as: location and orientation of each blasthole, stemming length, blasthole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect of the delay and its scatter in each blasthole on fragmentation and has a statistical modelling capability for geological random variation on attenuation of particle velocity wave. The wave reinforcement due to instantaneous waves arriving or diminishing cooperative contribution due to long delay intervals between charges is also simulated.The results are displayed in 3D volumetric plots, contour of fragmentation in cross-sections, and size passing curves for a whole blast or a region of the blast.CITATION:Yang, R, 2015. A multiple blasthole fragmentation model – its concept, formulation, capability and field comparison examples, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 177–186 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Brett

The Paper presents the authors thoughts on how the mining industry should be improving the education of site personnel so they can provide a greater level of effective control of tailings dam safety including empowerment to develop their own documentation, monitoring and surveillance systems and to better liaise with specialist external technical staff or consultants.

Jul 1, 2021

By F Sahlström, E M. Jolis, V R Troll, E Jonsson, K Högdahl, C Harris

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Bastnäs-type magnetite-skarn-hosted rare earth element (REE) mineralisations are located in the Palaeoproterozoic Bergslagen ore province, central Sweden, and occur along a ca 100 km long belt of 1.90–1.87 Ga metavolcanosedimentary rocks. Ten different Bastnäs-type deposits have been sampled in order to assess the origin of ore-forming fluids in these systems. Magnetite and quartz have d18O values ranging from -2.3 to +1.1‰ and +7.2 to +8.3‰ respectively. Mineralised carbonates have d18O values between +5.8 and +7.2‰ and d13C values between -5.4 and -3.3‰. Temperature calculations based on the O-isotope composition of mineral pairs, combined with available fluid inclusion data, suggest primary mineralisation at ca 650–400°C. For these temperatures, calculated equilibrium fluids have d18O values that range from those typical of magmatic fluids (+6 to +8‰) to lower values (down to +3‰). Variation in carbonate O and C isotope data are consistent with interaction between local Palaeoproterozoic carbonate rocks (d18O = +12.5 to +19.6‰ and d13C = -1.8 to +1.7‰) and fluids of a magmatic origin. It is suggested that the Bastnäs-type REE-magnetite mineralisations formed as a result of reactions between local carbonate units and high-temperature, magmatic-dominated hydrothermal fluids during 1.90–1.87 Ga (Svecofennian) syn-volcanic activity.CITATION:Sahlström, F, Jonsson, E, Högdahl, K, Harris, C, Troll, V R and Jolis, E M, 2015. O and C isotope study of Bastnäs-type rare earth element mineralisation, Bergslagen, Sweden, in Proceedings PACRIM 2015 Congress, pp 439–444 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Since the announcement of early experimental work on rotating magnetic field (RMF) separation at the Sixth Mill OperatorsÆ Conference in 1997, the concept of RMF separation has been developed and tested further, and a range of separator designs is now being developed for the mineral processing industry. Shortened, but full diameter, prototypes of these designs are now available for test separations. The main advantage of RMF low and medium intensity attraction separation is the significant reduction in particle entrapment. This reduction is so significant that RMF separators are capable of operating very close to their theoretical limit for separator precision. This makes small laboratory RMF attraction separators ideal for low to medium intensity magnetic sample analysis, and larger separators ideal for applications requiring sharp magnetic susceptibility splits. Feedrates and separation rates are comparable to those of conventional attraction separators. Although RMF attraction separators are now well advanced in development, RMF rotation separation is still in the early experimental stage. The exception to this is the dry particle rotation eddy current separator that offers eddy current separation of small non-ferrous metallic particles from about 2 mm down to about 100 microns. Wet small particle eddy current separation is also possible, but has not yet been developed to a practical stage.

Jan 1, 2000