Search Documents

Bacterial leaching of sulfide minerals are fairly well established in heap, dump and in situ leaching and the primary bacterial treatment of refractory gold concentrate using CSTR have gained industrial prominence in recent years. Three cultures, a mesophile T ferrooxidans (DSM583), a moderate thermophile Sulfobacillus acidophilus (strain YTF1) and a extreme thermophile (Sulfolobus strain BC65) were used for the biooxidation (pre-treatment) of the Porgera gold-bearing pyrite concentrate under optimum O2 and CO2 enriched air (30 per cent O2 and ten per cent CO2) based on volume ratios. The positive effect of using oxygen and carbon dioxide enriched air for the biooxidation of gold-bearing pyrite mineral was clearly demonstrated where an increase in Fe release rate by a factor of 2.8, 1.8 and 1.5 for DSM583, YTF1 and Sulfolobus respectively were observed compared with the shake flask tests. The lag phase observed with the other test conditions such as in shake flask or with air decreased by about 80 per cent for all three cultures. The average observed dissolved oxygen concentrations in the pulp for these tests were 8.7, 5.8 and 5.0 mg/L for DSM583, YTF1 and Sulfolobus respectively, indicating that O2 was not limiting in these tests. The pulp redox potential was observed to increase with time for all tests coincident with the leaching rate and reaching a maximum of 663 mV, however the maximum value differs for each strain, with DSM583 exhibiting the highest followed by YTF1 and Sulfolobus. Biooxidation of pyrite under optimum gas enrichment at different pulp densities showed near total Iron extraction occurred for pulp densities of three, ten and 20 per cent (w/v). At high pulp densities, more so at 40 per cent than 30 per cent (w/v), the leaching rate decreased rapidly for tests with YTF1 and Sulfolobus. Monitoring of dissolved O2 shows that O2 demand increased with increasing pulp density and the average dissolved O2 concentration observed for YTF1 and Sulfolobus at 40 per cent solids concentration was 1.0 mg/L and below, suggesting limiting oxygen and carbon dioxide conditions for these two cultures. The decrease in leaching rate observed at high pulp densities (30 and 40 per cent) under optimum gas enrichment was accompanied by low metal dissolution and low redox potential values which was attributed to shear stress due to attrition of cells by high solids concentration, toxicity of metal ions especially Ag and Fe and the formation of precipitates and jarosites as confirmed from XRD analysis of leach residues hence impeding the leaching process. Limiting conditions due to high pulp density and viscosity were only observed for YTF1 and Sulfolobus. The subsequent cyanide leaching for precious metals from the pre-treated pyrite concentrate in all cases shows the extent of gold and silver recovery increased with the degree of pyrite oxidation and Au and Ag recoveries in excess of 80 per cent were achieved compared with only 18.1 per cent and 35.9 per cent for gold and silver respectively when treated by direct cyanide leaching on the original, untreated concentrate.

Jan 1, 2004

By McLaughlin R. G, Brammer R. A J

King Island Scheelite had been using dealer modified front end loaders for two years when in 1974 it started to increase production. Suppliers were then quoting long deliveries for underground diesel trackless mining equip- ment, and the Company was forced to modify surface machines which had become redundant as production from the open cut phased out. The results were generally successful and encouraged further adaptations. Drill jumbos excepted, the Company now uses only converted surface machines in areas worked by diesel engined equipment and for all support and auxiliary functions.

Jan 1, 1977

By V Rajakumar, S Trang

Titanium has the potential to become the third wave of light metals used in high volume applications, following on from aluminium and magnesium. These light metals have functional attributes that can meet many of the goals needed for societyÆs transition to sustainable development. CSIRO has initiated a Light Metals Flagship to focus additional R&D efforts in support of the light metals industry. The vision of the Light Metal Flagship is for Australia to lead the Light Metals Age by reducing the costs and environmental impacts through innovative technologies for these metals. Life cycle principles will be used to identify novel technology pathways for metal production and product manufacture that are more energy efficient, less capital intensive and incorporating eco-efficient material flow chains.Under the auspices of the Light Metal Flagship, a Life Cycle Assessment (LCA) of titanium metal production was carried out with mineral sands mining of ilmenite as the starting point. Upgrading of the ilmenite to synthetic rutile by the Becher process and titanium metal production by the conventional Kroll process were the processing routes considered. Two alternative processes for titanium metal production, the FFC Cambridge process involving direct electrochemical deoxygenation of titanium dioxide, and a plasma process for producing titanium powder from titanium tetrachloride were also examined using LCA methodology and compared to the Kroll process. The environmental impacts included in the LCA were greenhouse gas emissions (Global Warming Potential, GWP) and acid rain gas emissions (Acidification Potential, AP). The Gross Energy Requirement (GER) of each process was also determined.These results for titanium, along with those from previous LCA studies by CSIRO on aluminium, magnesium, steel and stainless steel production, were used to show that despite the relatively large amounts of primary energy required for the production of these light metals, their special properties (eg corrosion resistance, strength and light weight) mean that these metals offer potential GER and GWP reductions compared to other competing materials in a number of applications, when viewed on a life cycle basis. Two applications considered in the paper are the lightweighting of motor vehicles and chemical plant equipment manufacture.

Jan 1, 2004

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

Minerals and Metals Group (MMG) Century mine (Century) is a large open-cut mine in northwest Queensland approximately 2.5 km long, 1.5 km wide and 240 m deep, with an ultimate pit depth of 320 m. In 2009, the mine experienced three failures which began as small failures, and progressively developed into significant multi-batter failures. The incidents were managed by a combination of analysis, redesign and practical management to achieve positive outcomes for the mine. On the south wall of the mine, a series of batter-scale wedge failures occurred in December 2007. Analysis of structure orientations and design changes aimed to minimise the risk of failure extending over multiple batters, while accepting a risk of further small-scale failures. Design changes were constrained by a culturally sensitive area (CSA) located south of the wall. As mining progressed, shallow wedge failures developed over multiple batters and cracks were observed 60m back from the pit crest, indicating that a large-scale wedge failure was developing. Movement increased in January 2009 as a result of significant rainfall. After considering several design options, the area was stabilised by a cut-back of the wall. Two multi-batter failures also occurred on the north wall as mining progressed through a structurally complex area. Both north wall failures began as small failures that progressively developed, and required a redesign of the wall below as well as practical management of safety aspects. The complex structural geology was difficult to predict ahead of mining, and required geotechnical input into design changes as mining progressed. All three failures potentially had significant impact for ore recovery, and were managed by a combination of analysis, redesign and operational management have resulted to achieve positive outcomes in a challenging mining environment.

May 1, 2010

By Oxenford R. J

An important rutile-ilmenite-zircon bearing sand deposit was discovered by local farmers at Eneabba, 300 km by road north of Perth in 1970. These heavy minerals occur in a series of ancient strandlines and associated dunal deposits at elevations from 85 m to 170 m above the present sea level and are situated,30 km inland. The strandlines were deposited on wave- cut platforms in an ancient bay bounded by Mesozoic sediments during a series of regress- ions from a high sea level, probably during late Tertiary or early Pleistocene times. The immediate source of the heavy minerals in the Eneabba deposit is a widespread low content of those minerals in the nearby Mesozoic sedi- ments. The high-grade southern portion of the Eneabba deposit has been closely drilled and is now being prepared for production by Allied Eneabba.Pty. Ltd., a subsidiary of Allied Minerals N.L. This part of the deposit is 11 km long and up to 2.5 km wide. It is characterised by little or no overburden and the average depth of mineralisation, bounded by a 2.5 per cent heavy mineral cut-off, is 12 m. The water-laid strandline deposits at the base of the mineralisation are generally high grade, ranging from 20 to 60 per cent

Jan 1, 1973

By Frew J. A, Harris M. C, Manlapig E. V

The recovery achieved in a flotation process is a function of both the characteristics of the feed stream and the operating conditions within the flotation cell. In this paper, the flotation characteristics of the streams within the Red Dog le

Jan 1, 1997

By Kristiansen J

A series of laboratory blasting and ball mill grinding tests have been done on four different types of hard and competent rocks. The results show that exposing these rock types to a higher level of explosive energy will enhance their grindability. True blasting optimisation should therefore look at the whole comminution process from solid rock to a marketable product.

Jan 1, 1995

Previous studies on the blast furnace raceway zone have been undertaken at three levels of scale, namely: laboratory models at low temperature, hot models which simulate coke combustion in the zone, and tests performed on operating and dismantled blast furnaces. This paper reviews the results of this published work on raceways in order to illustrate the factors which affect the raceway shape, size and combustion characteristics. As a result of the work it has been established that raceways are influenced by blast parameters such as velocity, temperature and chemistry, as well

Jan 1, 1981

By Pollard D. M

Chalcopyrite samples from two different localities were leached in oxygenated mixed chloride-sulphate lixivants at elevated temperatures and atmospheric pressure. The oxidation of chalcopyrite was found to follow predominantly linear kinetics. The slope of the major region was dependent on stirring rate, oxygen flowrate and chloride concentration while only slightly dependent on the surface area of the sample leached. This region was found to predominate only at low temperatures. The oxidised chalcopyrite releases cuprous and ferric ions into solutions. Chloride ions complex these dissolved ions to effectively move the equilibrium of the leaching reaction to the right. When the level of chloride in solution was below 6 g/l, the unstable cuprous ions were found to reprecipitate with sulphur as covellite. When no chloride was present and the lixivant was a solution of sulphuric acid then ferric sulphates precipitated. The overall leaching reaction occurring in the leaching system is: CuFeS2 + 5H+ + 1.25 02 = Cu 2+ + Fe 3+ + 2S¦ + 2.5H20

Jan 1, 1987

By Nott M. C

The oxidation of xanthate collectors to xanthate/dixanthogen results in a higher hydrophobicity of sulphide minerals surfaces due to the action of dixanthogen. This higher hydrophobicity can be proved on a fundamental level by examining the st

Jan 1, 1994

In the 1890s, The Goldfields Water Supply Department in Western Australia commissioned the diamond drilling of two deep artesian exploratory water bores near Coolgardie (Blatchford, 1899). At the time, in spite of strongly-worded advice to the contrary from the Government geologists, there was a wide popular belief that you could obtain artesian groundwater virtually anywhere providing you drilled deep enough. The first Coolgardie hole was drilled to over 900 m, despite the fact that the bore penetrated granite from a depth of 5 m below the surface. Drilling proceeded for more than 16 months, between July 1896 and November 1897. A small quantity of salt water was struck at a depth of 36 m. The second bore was mercifully terminated at a depth of 50 m, also in granite, with again only a small inflow of salt water. Such were the desperate lengths that were pursued to obtain a reliable water supply for the influx of people in the Eastern Goldfields gold rush. The WA Goldfields continued to rely on huge condensers for water supply until that great engineering feat, the construction of a water pipeline from Mundaring Weir to Coolgardie, was completed in 1903. An enormous network of rail tracks penetrated outwards from Kalgoorlie and Coolgardie for the collection of timber, principally to feed the condensers. Remnants of the rail network are still visible today. The acute shortage of fresh water led to great deprivation, disease and death among the early miners. Today, the water problems faced by the mining industry are thankfully not as severe, but they are nevertheless no less challenging. The southern part of the WA Goldfields is a notoriously difficult area for finding potable quality groundwater. Even as recently as the 1990s, there were occasional serious efforts to find potable groundwater in that area, some very imaginative and innovative. One mining company, working south of Southern Cross, spent many months experimenting with recovery of potable quality water from a shallow freshwater lens overlying hypersaline water in a low permeability weathered granite aquifer. They used very low capacity pumps manufactured from car windscreen washer pumps powered by solar panels.

Jan 1, 2000

The light microscopic study of the physical structures of coal and associated mineral matter is an important technique in providing information on the characterisitics and possible behaviour of coals in industrial processes. However the ultrafine nature of coal and mineral particles together with the limits of resolution of the light microscope restrict such studies. Scanning electron microscopy (SEM)with its better resolution and higher magnifications is the means by which further information on coal properties can be obtained. An associated energy dispersive X-ray specrometry (EDS) method allows non-destructive in-situ chemical analyses to be carried out at the same time.

Jan 1, 1989

Microorganisms have been used throughout history for the benefit of mankind with some of the earliest applications being in the production of fermented foods and beverages. Reactions involving inorganic substances such as metals, sulphur and sulphide compounds were hardly ever used until the early 1900s when it was discovered that Thiobacillus ferrooxidans was capable of promoting the oxidation of metal sulphides in ores. Today, it is widely recognised that biotechnology has great potential in the minerals industries, particularly in such areas as the leaching of low-grade ores of metals such as copper, gold and uranium; removal of heavy metal ions from process streams and from liquid process wastes; and in the desulphurisation of high-sulphur fuels. Although widespread commercialisation of mineral biotechnology has not yet been achieved, it is estimated that by the Year 2000 mineral biotechnology will have a significant impact on the minerals and metal industry and will probably account for tens of billions of dollars worth of annual production world-wide. This paper examines the actual and possible future applications of biotechnology in the minerals, metal refining and fossil-fuel processing industries. Firstly, the important chemical (and biochemical) principles involved in bio-dissolution of metals from ores and solid wastes, and in bio-accumulation of metals from process and waste solutions are reviewed, including leaching practices - past, present and future. Microbial desulphurisation of coal, and microbially-enhanced oil recovery are also discussed. The practical aspects of genetics and genetic engineering, the types and characteristics of those microorganisms important to mineral biotechnology, and the current research trends are reviewed as well. KEYWORDS: Biotechnology, microbial leaching, bioaccumulation, biosorption, bioleaching, biohydrometallurgy.

Jan 1, 1993

The coal basins that formed near the margin of Permian Australia were comparable in size with the Appalachian coalfields and with the European fields between Wales and Poland. They formed on the foreland side of a growing orogen in a system of linked transform basins formed by transtension on strike-slip faults. They were terminated and compressed when the Gympie volcanic arc was accreted to the orogen. Another huge system of Permian coal basins extending far inland from the Permian coast was also terminated when the Gympie Terrane was Accreted.

Jan 1, 1987

By G R. Hancock, D Verdon-Kidd, M J. Saynor, J B. C Lowry, T J. Coulthard

The ability to simulate the stability of post-mining landscapes over time scales ranging from decades to millennia is a critical element in the assessment of closure designs for uranium mines. Landscape Evolution Modelling (LEM) technologies provide a means to simulate and assess the long-term geomorphic stability of a conceptual rehabilitated landform for periods of thousands of years. However, a major issue with simulations derived from long-term modelling are the limitations associated with the data inputs. Specifically, simulations which utilise historic rainfall data only represent the variability of rainfall events that have occurred over a relatively short period. Consequently, these simulations run the risk of not accounting for the full range of rainfall variability that might be expected over an extended period of up to 10 000 years. Therefore, for this study a probabilistic approach was adopted to generate a stochastic synthetic rainfall data set to produce a series of unique rainfall scenarios, each representing a simulated period of 100 years. Importantly, utilising such an approach allows uncertainty in predictions to be better accounted for and provides a range or probability of likely outcomes.In this study, the effect of ten individual rainfall scenarios are assessed in terms of their impact on the predicted erosion and denudations rates produced by the CAESAR-Lisflood LEM for a conceptual rehabilitated landform of the Ranger Uranium Mine (RUM) in the Northern Territory of Australia, focusing on the Corridor Creek catchment (Figure 1). While legislation requires this site to be erosionally stable for at least 10 000 years (Commonwealth of Australia, 1987), here the focus is on the first one hundred years of landscape evolution, as this is the period in which erosion is expected to be higher, with limited vegetation cover or pedogenic development in the initial decades after rehabilitation. It is also the period where the drainage pattern is set.CITATION:Lowry, J B C, Verdon-Kidd, D, Hancock, G R, Saynor, M J and Coulthard, T J, 2016. Application of synthetic rainfall data to long-term modelling of a rehabilitated landform, in Proceedings Life-of-Mine 2016 Conference , pp 75–79 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By Boyd G

This paper describes the planning, analysis, design and operational experience of highwall mining based on auger drilling techniques applied to thick coal seams exposed in an opencut highwall. Being the first time such technology has been used in Australia, a large commitment to technical design and logistics planning was given by Callide Coalfields Pty Ltd. This commitment included technical and operations management and supervision, mine services, and the retention of consultants to undertake geotechnical analysis, instrument preparation and instrument installation.

Jan 1, 1991

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

Black coals occur in most of the major sedimentary basins in Australia. In addition to the better known Permian coal occurrences of the Sydney, Bowen, Oaklands and Galilee Basins, coals of Permian age occur in the Arckaringa Basin in South Australia, the Bonaparte Basin in Northern Territory and the Collie, Perth and Canning Basins in Western Australia and the Tasmania Basin in Tasmania. Coals of Triassic age occur in the Ipswich Callide and Tarong Basins in Queensland, the Tasmania Basin in Tasmania and the Leigh Creek area in South Aus- tralia. Coal bearing rocks of Jurassic age occur in the Mulgildie Basin and Maryborough Basins in Queensland and in both the Queensland and New South Wales portions of the Clarence Moreton Basin and Surat Basins. They also occur in the Perth Basin in Western Australia. Rocks of Cretaceous age known to contain coal occur in the Styx, Maryborough and Laura Basins in Queensland, the Gippsland Basin in Victoria and both the Queensland and New South Wales portions of the Surat Basin. The coal measures have been deposited in a variety of sedimentary environments and the coals vary widely with regard to thickness, extent, banding characteristics, maceral and ash content. However, they are generally of low rank and most are suitable only for steaming.

Jan 1, 1975

By Mitchell D

In recent years the need to provide increased ventilation to improve environmental conditions rather than to dilute firedamp has led to increasing interest in the use of recirculation. Present UK mining law prohibits recirculation in ventilation, but it has been permitted selectively by exemption granted by Hm Inspectorate of Mines and Quarries. The conditions of use imposed by these exemptions to safeguard the safety and health of miners are examined in detail, dealing separately with primary and auxiliary recirculation systems.

Jan 1, 1988