Search Documents

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

By Y Bissiri

The ever increasing demand for metals and minerals is putting significant pressure on current mining companies to find more ore. As these companies explore and mine, the future appears to be to go deeper and deeper underground. With depth, however, comes ever increasing costs as infrastructure such as hoisting, ventilation, the movement of workers and materials increase in size and scope. Further, the actual rock mass becomes prone to destruction through rock bursts and the heat generated becomes a major issue resulting in extreme expenditures in cooling plants and some of the biggest air movers in the world. All these issues result in dramatic changes in both capital and operating costs, subsequently making cut-off grades rise. As this trend continues there is an economic limit to how deep one can go, resulting therefore in a severe shortage of accessible ore deposits to mine. This paper discusses the need for larger marine robotics technology and presents the state-of-the-art in current research in underwater tele-autonomy, specifically the development of high bandwidth optical communication networks critical to any future activities (mining, construction, etc) underwater. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Offler R, Lau J, Lea J. F

The stratiform and vein-type pyritic silver-Iead-zinc-copper sulphide deposits of Sunny Corner, NSW are hosted by acid volcanic and clastic sedimentary rocks of Middle Silurian to Early Devonian age. The rocks have been subjected to low-grade regional metamorphism (prehnite-pumpellyite facies) and three phases of folding and four faulting events are recognised. Pyrite is intensely fractured, indicating brittle deformation. Chalcopyrite and galena exhibit deformation twins and slip planes indicating ductile deformation; sphalerite and chalcopyrite show straight and curved grain boundaries and dihedral angles of 120° as evidence of annealing recryslallisation. Sulphur isotope ratios for 22 samples from five deposits range from 1.7 to 10.7 per mil and average 7.4 per mil. Sulphur isotope data are similar to those from other stratiform sulphide deposits in acid volcanic rocks of Late Silurian age in the eastern Lachlan Fold Belt, especially Woodlawn and Captains Flat and together with other features of the mineralisation, suggest a volcanic exhalative origin for the Sunny Corner deposits.

Jan 1, 1984

By G T. Hefter, P Singh

The effect of using SO2 as an anodic depolariser in the electrowinning of copper from aqueous acid sulphate solutions has been studied using cells without/with a ceramic diaphragm. In all cases SO2-saturation of the electrolyte/anolyte decreased the anode potential by 68 to 75 per cent largely due to a change in the anode reaction from the oxidation of water to the oxidation of SO2 . However, poor quality deposits and low current efficiencies are encountered if SO2 is allowed free-access to the copper being deposited at the cathode. This situation is easily avoided by using a diaphragm to restrict SO2 to the anode compartment and for these conditions the resultant copper deposits are of a similar (high) quality to those obtained in the absence of SO2.

Jan 1, 1999

Australian contract mining as it is known today had its origins in the early-1980s. Before this time there were numerous examples of underground mine development, and specifically shaft sinking being carried out by contractors. However, these were typically international contracting companies who came to Australia for specific projects. Growth in the underground mining industry in the 1980s opened up the opportunity for contractors. Mine owners had a need for contractors who could bring technical and operational capabilities to a project combined with capital in the form of equipment. In the early years the contracting industry was dominated by smaller players who focussed on mine development. The relationship between mine owner and contractor was loose and typically contract documents were rarely referred to. Through the 1980s and 1990s the underground contracting industry in Australia grew to where today there are over 20 underground contracting companies operating in an industry with an estimated annual value in excess of $1 billion. Of these 20 companies approximately five dominate with annual turnovers exceeding $100 million. Underground contractors now provide all facets of underground mining including development and production. Over the last 20 years the underground contracting industry has been able to consistently lower costs to mine owners through a combination of:equipment productivity, labour productivity, and technical innovation.

Jan 1, 2002

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

By P Cavieres, R Dunlop, S Gaete

El Teniente Mine started the exploitation of the primary rock in the beginning of the 1980s decade, using caving methods. Since the beginning the mining activities have induced seismicity including some occasional rockbursts. Owing to the relevant damages, the mining operations were stopped in some production sectors. This paper describes the concepts that have been used in order to control the induced seismicity based on the strategies for controlling the rockmass breaking process, which depend on mining parameters. It also presents the main concepts applied in the Teniente Sub6 sector design and the experience collected during its sector exploitation.

Jan 1, 2000

Universal Resources Ltd has acquired a large portfolio of high quality exploration projects in two of Australia's most prospective regions for base and precious metal exploration: the Mt Isa Inlier (the Mt Isa-Cloncurry area) of North West Queensland, and the southern Lachlan Fold Belt in New South Wales. Drilling techniques commonly employed by the company for mineral exploration include diamond core drilling, air core drilling, reverse circulation (RC) drilling, and rotary air blast (RAB) drilling. Using examples from these two regions, each drilling technique is briefly described and compared, with particular reference to the specific advantages and disadvantages of each method for: sampling size, sample representivity, recovery, integrity and potential contamination. The applicability and implications of the different drilling techniques described for subsequent mineralogical and metallurgical evaluation work are discussed.

Mar 1, 2010

The considerations which led to the decision to_ install discs at the Dampier Pellet Plant of Hamer ley Iron Pty. Ltd. are described. Initial testwork showed that the ore could be ground dry in open circuit to a Blaine index of 2500 cm2/g and that it pelletized readily. The various design criteria including diameter, slope, speed, motor size, depth of sidewall, feed point and water spray location were then determined. Plant performance after commissioning is described including the various problems encountered and the modifications since carried out to overcome them. The main problem was quickly identified as disc feed rate control. Various bin and bin feeder modifications were tried to overcome the effects of the fluidising characteristics of the dry ground ore. Other factors found to affect disc operation are ore size distribution, additives and operator competence.

Jan 1, 1974

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

By Brook W. H

The history of the reduction of iron from its ores is lost in antiquity. Archreologists state that man has practised it for over four thousand years. Until comparatively recent times charcoal was the principal reducing agent for making metallic iron from its various oxidised ores. Coke was first used by iron founders in England in 1619, and its use spread gradually throughout the civilised world from then onwards. Indeed, the destruction of forests to obtain the requisite charcoal made the iron founders, both in England and America, extremely unpopular, and this hampered the iron industry to a considerable extent, until coal provided the metallurgist with a new and better fuel--coke which is used by most pyro-metallurgists today. The transition from wood to coal products for iron smelting had a profound effect on the location of iron works. Particularly was this the case in America where, in the infancy of the industry, practically each of the early States had its own iron producers, but as coal and coke replaced charcoal, there came about a concentration of the iron and steel industry around the coking coal deposits, and so today there are huge steel plants clustered around the soft coal basins in Pennsylvania and Illinois.The development of the iron and steel industry in Australia, which is comparatively recent by world standards, has been cradled in the coal basins of New South Wales. The first steel works of any consequence in this country were built near Lithgow, close by the mines which produced the coal for coking.Incidentally, these works were rather unique in that the three essential materials for iron and steel manufacture-ore, coal, and limestone-were found virtually at the works' back door.When, in 1912, the location of the proposed steel works for The Broken Hill Pty. Co. Ltd. for smelting ore from Iron Knob in South Australia was considered, the site ultimately chosen was at Newcastle, almost on top of seams of satisfactory coking coal. One of the major factors which had determined the site of the steel works was the fact that, about 1912, three tons of coal were required to produce one ton of finished steel product, and the relative economics of ore and coal haulage were much in favour of bringing ore to the coal.

Jan 1, 1947

New Zealand contract mining has been well established for close to 50 years. The opencast industry has grown from mining quantities of less than 1 million bcm per year in the 1950s to around 20 million bcm in the late 1990s. Trends here are following those in other countries with mining companies looking to contract out more of the so called traditional mining work. The key driver behind this trend is not unique to the mining industry, but is simply a matter of concentrating on doing a few things well. In the case of the mining company this has come to mean owning and developing orebodies and where appropriate, marketing mining products, and leaving owning and operating of mining fleets to the contractor. This has the effect of reducing risk to the mining company as well as lowering costs. Both can be achieved without losing control of the key elements of the operation. Optimising performance is simply a matter of identifying the key drivers behind performance, having the right plant and the right people at the right place and providing these people with the information they need to manage the operation.

Jan 1, 1997

By R Higashi, D Maruoka, T Murakami, Y Iwami

The ironmaking industry consumes a large amount of fossil fuel derived carbon as heat source, reducing agent of iron ores and carburising agent of reduced iron. Although the demand for drastic decrease of carbon dioxide emission, carbon is an essential element for smelting process of molten iron. The carbon recycling ironmaking process by circulating CO has been already proposed to achieve carbon neutrality. However, the production of molten hot metal is not considered in this process because sufficient amount of carbon does not dissolve in reduced iron by CO. Therefore, our group has suggested a new carbon recycling ironmaking process which can produce hot metal. In this process, free carbon and iron carbides produced by carbon deposition reaction using metallic iron as a catalyst are used. It is known that only Fe3C is obtained as iron carbide by using CO gas, however, Fe5C2 is also produced by adding H2 gas. The composite agglomerated with these carbonaceous materials and fine iron ore (Deposited Carbon-Iron oxide Composite: DCIC) is reduced and melted in a furnace. It is reported that Fe3C in DCIC accelerates the reduction reaction and melting of the composite. In this study, the effects of iron carbides and free carbon on the melting behaviour of DCIC are investigated. Fe3C, Fe5C2 and free carbon were produced by vapour deposition using porous iron whiskers and CO-CO2-H2 gas. These were agglomerated with hematite reagent at a certain ratio to prepare DCIC samples with and without Fe5C2. The samples were heated up to 1300°C in inert atmosphere. The DCIC containing Fe5C2 completely melted and iron nuggets were obtained after the experiment. This behaviour was not observed in the composite without Fe5C2. This indicates that using Fe5C2 is more preferable than Fe3C for molten iron production using DCIC.

Jun 19, 2024

By K Nilsson, G Cheong

Troy Resources NL acquired a 70 per cent interest in the Mina Sertpo gold project in Goißs State, Brazil, in 2001 following a successful bid for the highly competitive international tender of a tenement package put out by Western Mining Corporation (WMC). The Sertpo deposit is located on cleared grazing land 380 km west of Brasilia and is 30 per cent owned by Amazonia Mineracao Ltda, a private Brazilian company. It is a small high grade open-pittable orebody with a measured and indicated resource of 108 000 tonnes at a grade of 49.7 g/t for 172 500 ounces using a 2.0 g/t cut-off. Troy undertook the project management and development of the project while Amazonia managed the exploration activities and provided other services as required. The project development involved drilling metallurgical test holes, scouring the world to locate an available and suitable second-hand plant, and arranging shipping to andreconstruction in Brazil.

Jan 1, 2004

By P Dean, M Elmouttie, Y Duan, X Luo

Slope instability is one of the major concerns in open pit mining operations. A significant collapse of the pit wall can result in injuries, damage to machinery and interruptions to production. A broadband microseismic monitoring technique has been developed for diagnosing the healthy condition of a target slope area. This technique has been successfully applied to an open pit mine in Chile. Our research has found that this microseismic monitoring technique can be used in open pits for tracking and locating a falling rock that is rolling on a slope, if a dedicated seismic sensor network has been established. In collaboration with other monitoring techniques (radar, laser scan, aerial photography), more accurate determination of rock rolling trajectories can be obtained. In this paper, an example of using the CSIRO microseismic monitoring technique at an open pit mine is presented. Results from an experiment where we used the microseismic technique for determination of the trajectory of a rockfalling on a slope are also presented.

Nov 8, 2021

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

Despite extensive oil exploration in"Western Australia over the past 12 years no commercial oil fields have yet been found. A total ' of 66 test wells have been drilled throughout the State but only Rough Range No.s.. 1 and 1A have produced oil in significant quantities. Active oil exploration is now in progress in the" Canning, Carnarvon, Perth, Bonaparte Gulf and Officer Basins. Test wells have been drilled' in ,all of these except the Officer Basin, where the subsurface stratigraphy is still unknown. Large .areas of the other four have hot yet been drilled. It, is- probable that. commercial oil deposits will eventually be found' in these basins as they contain thick marine sequences, and have structures 'suitable for.,the. entrapment of oil. .

Jan 1, 1964

By H Bleuler

A new portal and access drift was constructed by Concrete Constructions for BHPÆs Elouera Colliery, south of Wollongong.The portal area at the base of the Illawarra Escarpment is in soft colluvium material, underlain by highly to moderately weathered sandstone. The area has a well documented history of slope movement or slope creep and one of the main criteria for the design was to minimise disturbance to the unstable slope by limiting the excavation for the portal establishment. This was achieved by incorporating a sloped headwall and gabion wingwalls to accommodate the anticipated creep and groundwater seepage.Main features of the design process also included the provision of both primary and secondary support in a single shell application and the use of canopy tubes to provide support ahead of the tunnel face.The active involvement of the designer during the construction phase and the flexibility of the design concept allowed changes to the support methodology to be carried out as excavation proceeded.This paper describes the design process undertaken for portal establishment and access drift to cater for the variability of the exposed ground conditions along the drift alignment.

Jan 1, 1999

By Davies H, Pigram C, Sunata W, Falvey D, Loxton C, Giddings J, Rogerson R

PALAEOMAGNETIC CONSTRAINTS ON TERRANE TECTONICS IN NEW GUINEA Chris Klootwijkl), John Giddingsl), Wahyu Sunata2), Chris Pigraml), Charles Loxton3), Hugh Daviesl), Rick Rogerson3) and David Falveyl) 1) Bureau of Mineral Resources, Canberra, Australia 2) Geological Research and Development Centre, Bandung, Indonesia 3) Geological Survey of Papua New Guinea, Port Moresby, Papua New Guinea

Jan 1, 1987

By Sano S, Ishikawa T, Nagaoka H, Hayashi Y, Hasegawa M

The stirred mill is regarded as one of the most efficient devices for micronising materials and has come to be actively used for preparation of fine particles. Recently, the demand for ultrafine particles was increased in many kinds of industries. In this paper, autogenous grinding to get submicron particles based on mutual friction feed material has been carried out using a stirred mill. The mill used was made of stainless steel and its volume was about 5.5 litres, and has 12 impeller blades. Sample used was limestone. In the present work, two operating parameters such as stirring speed and feed size of limestone were considered. The ground products were sieved in the size range from feed size to 325 mesh (45 lun), and from 45 to 0.17 pm the size distributions were measured by a laser diffraction and scattering method. The progress of grinding was evaluated by the increasing amount of submicron particles in products. As a result, the rotational speed of impeller with the minimum energy consumption to produce submicron particles was observed. It was found that the autogenous grinding with a stirred mill is an effective method for producing submicronized limestone.

Jan 1, 1993