Search Documents

By Sulanto J, Talonen T

In the mid 1960's Outokumpu considered building a lead Flash Smelter on the basis of Flash Smelting technology developed first in the late 1940s for smelting copper concentrates. Pilot scale tests were carried out and the process was found technically sound. The project was however not economically viable under Finnish conditions and it was cancelled. In 1981 pilot plant tests were restarted after many enquiries from the primary lead producers. All the know-how and development made in copper and nickel smelters was applied to the Lead Flash Smelting process and the tests were successful. Outokumpu has so far tested several types of lead concentrate with lead contents ranging from 28 to 75 per cent. The concentrate is oxidized and smelted to metallic lead and slag directly in the Flash Smelting Furnace using high oxygen enrichment of tonnage oxygen. Fossile fuel is used in the Flash Smelting Furnace in cases when the feed material does not contain enough latent heat to smelt the furnace products even though pure oxygen is used for oxidation. Thus the process results in a low consumption of extraneous energy. Use of oxygen results in a small gas flow but it is rich in sulphur dioxide. The gas treatment facilities and sulphur recovery plant will be small in size and low in investment cost. The process is flexible and can produce stable quality of products from different types of raw materials. Quality of lead bullion especially the sulphur content can be regulated over wide a range, from 0.1 per cent upwards according to the needs of the refinery.

Jan 1, 1984

The title of this paper implies, and the text explicity states, that Sen and Spottiswood (1984) have found a new mineral species related to geocronite and jorganite. I believe that there is inadequate justification for this claim.The X-ray powder diffraction pattern reported by the authors exhibits a close similarity to that of geocronite, as stated by the authors, which suggests a close structural relationship at the very least. It is therefore reasonable to recalculate the results of the microprobe analysis reported by them to atomic proportions on the basis of the geocronite formula. This calculation, whether based on the formula used by Sen and Spottiswood (1984), or on one derived from a crystal-structure analysis (Birnie and Burnham, 1976), namely Pb18 (Sb, AS)11S46, with a total of 86 atoms, gives the results shown in Table 1.

Jan 1, 1985

Mining companies often view water quality as an environmental issue. The importance of water quality as a production related issue in mineral beneficiation is greatly underestimated at many mineral processing operations. While most mine sites have comprehensive water balance data for water quantity, the information regarding the quality of water supplies available on site is limited, inadequate or non-existent. The seasonal variations in process water quality and changes in the composition of various water streams are not known. Despite the fact that water represents about 80 to 90 per cent of the volume of mineral pulp processed in a flotation plant, the influence of process water composition on flotation performance is often poorly understood. The process water used at mineral processing operations is made up from a number of available water sources, which can be classified as recycled water streams or make-up waters. The recycled water streams are commonly the tailings and concentrate thickener overflows, filtrate from the concentrate filtration plant and tailings dam return water. Make-up waters can originate from a variety of sources: surface waters (rivers, lakes, reservoirs, dams), groundwater (wells and springs), mains water (potable water), treated and untreated sewage waters and industrial effluents. Mineral processing plants are increasingly recycling water to reduce demand for fresh water and minimise the discharge of wastewater to the environment. However, increasing water recycling can have adverse effects on process water quality and ultimately on the performance of mineral separation processes. The main reasons for reduced plant performance due to water recycling are the accumulation of organic and inorganic compounds in the process water and increased microbiological activities. Other detrimental effects of water recycling can be increased reagent consumption and inefficient dewatering of tailings and concentrates. Recycling of water also tends to accumulate very fine suspended particles. Excessive amounts of slimes in the process water can also have an adverse effect on mineral beneficiation processes. The main constituents of process water are dissolved gases (oxygen, nitrogen, carbon dioxide), colloidal and suspended solids of inorganic and organic nature (including micro-organisms: dead or alive), dissolved organics (natural organic matter, residual reagents, reaction and decomposition by-products of chemical reagents, impurities in the reagents and metabolites originating from microbiological activities) and inorganic compounds (acids, alkalis, inorganic salts, metal ions, anions and heavy metals). Inputs to the chemical composition of process waters are: dissolution of soluble mineral phases present in the ore, surface oxidation followed by dissolution of mineral particles during grinding and mineral processing, the chemical composition of various make-up waters and recycled water streams, and reagent additions during mineral processing. The beneficial or detrimental impact of process water quality on flotation performance can be attributed to a number of subprocesses: adsorption and/or precipitation of inorganic and organic species present in the process water onto the surface of mineral particles, chemical reactions between process water constituents and the chemical species present on the surface of mineral particles and interactions between the chemical and microbiological species present in the process water and the various reagent species added in solution during mineral processing. Dissolved chemical species such as calcium, magnesium, iron, copper, lead, zinc, nickel, sulfates, phosphates and carbonates can have a strong effect on the electrokinetic properties of oxide and sulfide minerals, at certain pH ranges. Several reactions can occur at the solid-liquid interface that can play an important role in determining surface adsorption of reagents. Solid-liquid interfacial properties of mineral particles can be significantly affected by the conformation of adsorbed and precipitated reagent layers, which in turn are determined by solution chemistry. The chemical and microbiological constituents of process water can have a significant effect on liquid-gas interfacial properties and have a strong influence on froth height, strength and stability during flotation. Water chemistry can play an important role in determining the interactions between minerals present in the ore and the chemical reagents added in the mineral processing plant by altering the reagent-solution and mineral-solution equilibria. These interactions can include dissolution, micellisation and precipitation of reagents, dissolution of minerals contained in the ore followed by hydrolysis, complexation, adsorption and precipitation of dissolved chemical species and reactions between dissolved ions and various reagent species present in solution. All of the above mentioned subprocesses can ultimately have a significant effect on the efficiency of mineral processing operations. In this presentation, a systematic approach for assessing the composition of water supplies available at the mine sites and for investigating the influence of process water quality on the efficiency of mineral processing operations will be discussed. The consequences of mixing different quality water streams to produce the required volumes of process water for some flotation plants will be highlighted. To substantiate the water quality issues described in this paper some examples are given from a metalliferous processing perspective. However, the topics described in the paper are not only relevant to metalliferous processing but to all other type of mineral processing operations as well. In fact the principles described in this paper have also been successfully applied to the coal flotation industry.

Jan 1, 2006

By Eisele TC

Horizontal perforated-plate baffles were shown to improve the cleaning efficiency of a flotation column when processing coal from two sources. The baffles consisted of flat plates with holes large enough to avoid plugging problems, and they improved the washing efficiency by making the flow patterns in the column closely approach plug flow. Tests with varying amounts of baffle open area showed that the optimum was between 30 and 40 per cent open area, which effectively prevented backmixing without seriously reducing capacity. The baffled column had previously been tested under ideal conditions with good results (87 per cent pyrite rejection at 85 per cent combustiles recovery), and so the tests reported here were intentionally run with difficult-to-float coals to determine the benefits of baffling under adverse conditions. For an original coal feed containing 38 per cent ash and 3.23 per cent total sulphur, the baffled column could recover 84 per cent of the combustibles while rejecting 84 per cent of the ash and approximately 54 per cent of the pyritic sulphur. Without baffles, the column recovered 88 per cent of the combustibles while rejecting only 76 per cent of the ash and 45 per cent of the pyritic sulphur. Subsequent tests with a dye tracer showed that the baffles reduced entrainment by approximately a factor of five, while the recovery was reduced by only a few per cent. Overall, the loss of capacity due to the baffles was more than offset by the improvement in product quality.

Jan 1, 1993

The paper focuses on how rock bolts are loaded in different rock masses, as well as in pullout tests. Three analytical models for rock bolts are presented in brief, one for bolts in continuously deformed rock masses, one for bolts in blocky rock masses, and one for bolts in pullout tests. The bolt models are used to interpret measurement data for rock bolts from three sources and to help specify the modes of axial load in the rock bolts. It is found that in continuously deformed rock formations fully coupled rock bolts have only one axial stress peak. The position of the axial stress peak moves towards the far end of the bolts with increasing rock deformation. In blocky rock masses several axial stress peaks may appear in the rock bolt. The position of this kind of axial stress peak does not change during the entire loading process. For rock bolts in pullout tests, decoupling of the interface always occurs first at the loading point. The decoupling front moves towards the far end of the bolt with an increase in the applied pull load.

Jan 1, 2000

By Muller M, Ashley PM

Massive sulphide ZnPbCuAg deposits in the Halls Peak district of northeastern NSW are of the submarine volcanogenic type. They occur as a number of small lenses enclosed in shale and epiclastic rocks, in association with felsic volcanics of early Permian age. The deposits crop out in steep terrain near the eastern edge of the New England plateau. Local relief of 700 m and slopes up to 50¦, coupled with an average annual rainfall of about 1000 mm has led to local severe landsliding in previously mined areas. Mining from the 1890's to the 1960's has also resulted in unconstrained drainage of heavy metal-bearing acid waters and physical dispersion of finer grained metalliferous sediments into the Chandler River. Waters emanating from the main landslide area, from underground workings and draining scattered unconfined stockpiles of massive sulphide ore have pH values of 3 to 4 and contain elevated contents of Zn, Cu, Pb, Cd and Fe. Chemical mobility of heavy metals into streams occurs under low pH conditions with Zn exhibiting the greatest dispersion. Increasing pH conditions downstream cause precipitation of Fe phases and coprecipitation of heavy metals. Physical dispersion of secondary metal-bearing minerals into the surrounding creeks results in wt% levels of Cu, Pb and Zn in the stream sediments thereby exceeding the regional background values by one to three orders of magnitude. Areas disturbed by mining are characterised by lack of vegetation, biomagnification of heavy metals into algae and lower plants, and partial recolonisation by metal-tolerant grass species (Snow Grass, Poa sieberana; Blady Grass, Lomandra longifolia). Rehabilitation measures will have to include landslide stabilisation, impervious sealing or removal of sulphidic materials, import of topsoil and revegetation by metal-tolerant, slow-growing native grass and shrub species.

Jan 1, 1995

By Weller KR, Restarick CJ, Stewart PSB

Following a detailed assessment of concen trator performance at Broken Hill South Limited which was reported in a previous paper, the fine grinding section was changed from a parallel arrangement of the two grinding circuits to a series arrangement, and the concentrator per- formance re-assessed. The change to series grinding had virtually no effect on the actual or potential capacity of the circuit to make a final product with 80% passing 100 mesh. However, the fresh flotation feed contained significantly less +150 mesh lead and +65 mesh zinc (material which was shown to float poorly), without an increase in the quantity of poor-floating ultra-fine lead and zinc. From the size-by-size flotation recovery data, it was shown that overall recoveries of both lead and zinc were approximately 1% higher than they would have been without this change in size distribution and it was concluded that this was a direct result of the change in grind- ing procedure.

Jan 1, 1972

By Standish N

The heterogeneous reactions of carbonaceous materials with oxidising gases are basic to all combustion phenomena and to many gasification processes. The carbon- carbon dioxide reaction at elevated temperatures (Reactivity) plays important roles in many metallurgical operations like iron blast furnace and ferro-alloys smeltings, zinc and lead smelting, alumina reduction, cupola operation and direct reduction processes. The stoichiometry but not the mechanism of the reaction between CO2 and carbon is represented by the equation (Boudouard reaction) CO2 + C 2CO (1) This reaction is more complex than that between carbon monoxide and metal oxides, which involves essentially a transfer of oxygen from the oxide to carbon monoxide to generate carbon dioxide without any change in gas volume, whereas the volume of the product gas of Equation (1) is twice that of the reactant gas. In the present paper an attempt has been made to review critically the reactivity measurements of various carbonaceous materials in carbon dioxide atmosphere. Steps in C-CO2 reactions, surface reaction mechanism, role of mass transfer on reaction kinetics, dynamic oxygen exchange reaction and rate equations and rate controlling steps are discussed. Various methods of reactivity measurements with their pros and cons are also presented. Effects of pertinent process variables on the reactivity of carbon are also described in detail.

Jan 1, 1986

By Scott RM

The project management and construction plans adopted by Davy McKee for the Cooper Basin Liquids Project resulted in a project notable for the Relatively short duration from initiation of the design through to liquids production. Two locations were involved, one at Moomba in the far northeast of South Australia some 800 km from Adelaide, and the other at Port Bonython some 40 km from Whyalla. Total expenditure by the owners at the two sites was in excess of $600 million. Matters covered include organisation, transport, construction, industrial relations, project services and commissioning.

Jan 1, 1986

Western Mining Corporation (WMC), managers of the Windarra Nickel Project, installed a raise-bored haulage shaft and underground crushing system at the Mt Windarra Nickel Mine in 1982. The system is the second of its type installed by WMC, the first being at the Otter Juan Mine in Kambalda in 1976/77. Both haulage systems became necessary as a result of the increasing production limitations, and escalating costs of a deep decline mine.The Windarra haulage system required a single 3 m diameter vertical raise drill hole, 470 m deep and equipped for skip haulage. Two five tonne skips, in balance, hoist crushed ore and mullock to the surface, at a design rate of 200 tonne/hr, effectively reducing truck haulage leads by up to 50 per cent. The system is now fully operational and will enable the mine to achieve its maximum production rate.The raise-bored shaft system has been shown to be cost effective and would be used again in circumstances where raise drilling is applicable.

Jan 1, 1984

By Just GD, Gillies ADS

The competitive coal market has required coal producers to put more effort into coal quality control. Successful quality control requires a good estimation of the in situ coal quality as well as a good estimation of the probable fluctuation of the in situ coal quality during production. Geostatistics offers a very promising way to meet this requirement. A geostatistical approach toward the coal quality control problem is presented. Two models, the prediction model and the conditional simulation model, have been developed for coal quality data from two large export coal mines in central Queensland, Australia. The mine planning and scheduling aspects based on this and other potential applications of the models are addressed.

Jan 1, 1990

Knowledge of coalfield geology has evolved rapidly over the past few years. Recent advances ranging between exploration, mining geology and seam variation studies have enabled application of geological techniques commensurate with technological changes in the coal industry.

Jan 1, 1969

By B Roach, P M. Ashley, B Hooper

Mineral occurrences of the Hillgrove Au-Sb-W district are hosted in late Palaeozoic polydeformed, hornfelsed metasediments and Permo-Carboniferous granitoids of the NewEngland Orogen. In excess of 204 individual occurrences have been identified to date with the mineralisation developed as strike extensive (>20 km of known veining) and potentially depth extensive steeply dipping fissures. These are contained within an elongate area measuring some 9 km by 6 km in surface dimensions. Recorded gold production of 720 000 ounces along with current resources in the order of 340 000 ounces highlight the significance of this district. Historical antimony production is estimated at in excess of 50 000 metric tonnes. Significant tungsten of over 2000 t in the form of scheelite has also been produced from the field. Mineralisation is developed in veins, vein breccias, sheeted veins, network stockworks and as alteration sulfide haloes to the main structures. The vast majority of fissures are subvertical and vary in widths of up to 20 m in places. Paragenetic studies have previously indicated that the earliest mineralising event was a scheelite-bearing phase of quartz veining. Subsequent phases of arsenopyrite-pyrite-quartz-carbonate veining were accompanied by gold and minor base metal sulfides. Alteration is typically sericite-ankerite-quartz. Overprinting stibnite-quartz veining with gold-electrum, aurostibite and arsenopyrite form an important subsequent phase. Veining can be inferred from historical records to extend for vertical depths of over 1 km.

Jan 1, 2004

Financial markets are subject to constant change and project finance, as a product within these markets, adapts and will continue to adapt with those changes. A meaningful discussion of these adaptations requires an understanding of differences between non-, limited and full recourse project finance. The reasons sponsors seek and lenders provide project finance are also pertinent in this context. Arranging a project, financing package can be a canplex and time consuming task. An important first step is choosing the right advisor for the assignment and then structuring and tailoring the financing before approaching prospective lenders. The last thirty years has seen changes in the needs of sponsors and the ability of lenders to meet them. These shifts in preference may well be a guide to the future. Several major project financings successfully canpleted in Australia in the last few years and more recent examples are broadly discussed. Project finance will be keenly sought in the future and the form and nature it takes will continue to vary.

Jan 1, 1983

By Artieda JJ, Catalina JC

- The aim of this paper is to analyse the possibilities of applying signal processing and artificial vision techniques to the ore sorting problem. In order to overcome the limitations imposed by the classical approach to the problem, which essentialy cons

Jan 1, 1985

By L Faulkner

The Tarnagulla Gold Project in Central Victoria, Australia, was developed and operated by Reef Mining NL between 1994 and early 2000, producing 53 000 ounces of gold from the Nick OÆTime Shoot, a single narrow vein shoot structure within part of the larger Poverty Reef, with a strike length ranging from 30 m to 60 m. The ore shoot was developed over a vertical interval of 190 m, using a small cross-section decline and small, mechanised equipment. Various stoping methods were employed including mechanised cut-and-fill with a single boom jumbo, hand-held mining using airleg drills and rope scrapers, and small uphole retreat stopes using a line of sight remote operated LHD to recover a crown pillar. Experience during stoping showed that airleg drilling and rope scrapers gave much better dilution control than diesel equipment. Innovations included a low-cost hydraulic fill system. Due to the small scale of the deposit, the feasibility studies, planning and permitting for the mine were based on very limited drilling information; however, the mine was brought into production within two years of the discovery. While the mine made an operating profit, it failed to fully repay capital at the low gold price then prevailing. Applying the lessons learned from the operation to optimise the access and stoping method, the project is re-examined at todayÆs gold price and operating costs. Central Victoria has the potential to host many similar small deposits. The authors were respectively Non-Executive Director and Resident Manager for Reef Mining NL when the mine was operating.

Jan 1, 2008

By Fourney W. L, Dick R. D

Tests were conducted in plexiglass and Rockite models to determine if crater blasting could be improved by changes in charge geometry or by alterations to the borehole. Circumferential grooves were placed at various locations in the borehole in an attempt to control the initiation site of the crater. Grooves located at or above the top of the cylindrical charge had no effect on the resulting crater. Grooves placed too low in the borehole were successful in controlling the initiation site but the growth of the fracture system was not sufficient to reach the upper surface. Grooves located at a height of two thirds of the charge length were quite successful in that resulting craters were bigger by at least a factor of six than the normal crater. Testing was conducted in Rockite models to investigate charge geometry. Spherical charges in ungrooved boreholes resulted in crater sizes that were three times larger than those caused by cylindrical charges.

Jan 1, 1990

By Lyman GJ, Davis JJ

Models which have been presented in the literature consider only selected aspects of dense medium cyclone operation, are empirical in nature and generally relate only to severely limited ranges of operating parameters. This paper reports progress towards development of a more comprehensive and robust model. The data base consists of partitioning parameters developed using density tracers and conventional coal sampling and analysis techniques, together with recordings of parameters such as cyclone dimensions, feed pressure, medium size distribution and product media densities.. These data were drawn from 15 Australian coal preparation plants. To elucidate the effects of important operating parameters on medium behaviour and on the partitioning of large particles a series of pilot scale tests was also conducted. The present model consists of eight sub-models which relate to particular aspects of dense medium cyclone operation such as medium flowrates and densities, or size- by-size separation densities and Eps. The model structure follows a logical progression which clearly demonstrates the importance of understanding medium behaviour before attempting to predict partitioning performance. The model also attempts to define the conditions under which yield losses due to unstable "surging" discharge may occur.

Jan 1, 1987

By Takagi T, Seetharam R, Sie SH, Naito K

Tin-polymetallic vein type deposits are one of the major source of metal producers in the Circum Pacific Belt. This type of deposit is of great importance for the modem electronics and medical industries because of their high content of rare metals (especially indium and bismuth). We have studied two representatives, Tosham of India (Cu-In-Bi-Sn-W-Ag-Au), and Mount Pleasant of Canada (Zn-Cu-In-Bi-Sn-W), using proton and electron microprobes in order to delineate the distribution of medical/high-tech rare metals. The electron microprobe study showed that major indium carrier in such type of deposit are roquesite (CulnSZ), sphalerite, stannite and a Cu-Zn-Fe-In-Sn-S mineral; and that indium is incorporated in sulfides by coupled substitution like Cu + In = 2(Zn + Fe). The proton microprobe showed that indium at trace levels is also present in chalcopyrite and pyrite. In addition, zinc, copper, arsenic, antimony, selenium, tin, and bismuth are common in chalcopyrite and pyrite. Arsenopyrite contains nickel, copper, zinc, silver, tin, antimony and bismuth. In chalcopyrite and pyrite, zinc, arsenic, indium, bismuth and lead are higher in Mount Pleasant ore, but silver is higher at Tosham. Also thallium and gold were found only in Tosham pyrite. The Tosham deposit is genetically related to S-type magma, while the Mount Pleasant deposit is related to A-type granite. Tosham ore contains zinc-bearing biotites that coexist with chalcopyrite in ore bodies but Mount Pleasant ore lacks such biotite. We propose that the difference in elemental abundance between the two deposits are caused by the different character of source magma and different mineral associations of the ore body.

Jan 1, 1995

By P R. G Milne

A risk-based approach to optimising pit wall slope angles was trialled in the design of a 60m deep open pit in extremely weathered and distinctly weathered materials in the Kalgoorlie area. The pit used for this approach was Stage 1 of a three-stage open pit project. The Stage 3 pit will require long term stability, as it will contain the portal for a long life underground project. Information from failures induced by steeper wall angles used in the Stage 1 pit would be valuable in predicting and preventing long-term stability issues in Stage 3. In this approach, the pit wall slopes are based not on the normal factors of safety, but on the assessment of the probability of failure and the direct and indirect costs of dealing with the failure when it occurs. In this example, the benefits and risks of adopting steeper wall angles were compared in a series of graphs. These charted the increasing probability of failure and simultaneous decreasing factors of safety with increasing pit wall slope, and the range in the possible volumes of circular failures for increasing wall angles. These were brought together in a graph showing the potential excavation savings (in BCM) and the probable cost of a failure (probability of failure times the probable volume of the failure). The resulting pit design was based on the project Mining EngineerÆs semi-quantitative assessment of where and when a higher risk of failure was acceptable and where it was not acceptable as it may have unduly affected the integrity of haul roads or production. The design incorporated wider than normal berm widths to accommodate anticipated failures and to enable modification of the wall configuration if required. Several re-designs were required during the life of the project in response to aggressively induced failures. It is considered that this risk-based approach provides a practical route to optimal pit design and operation but it requires an experienced, dedicated and efficient mining team for it to be implemented with benefit.

Jan 1, 2003