Search Documents

By P Craig, M Holden, C Zhang, D Foster, J Oh, S Saydam, J Liu, H L. Ramandi, S Akdag

High stress in rock masses can cause significant instability problems such as squeezing deformation in soft rock and rock bursts in hard rock. The support system applied in burst-prone areas in high-stress conditions is required to be able to carry high load and accommodate large deformation of the rock mass without experiencing any serious damage. Yielding support systems are promising to provide support for both squeezing and burst-prone rock mass encountered in mining or tunnelling at depth. They are ideally strong and stiff initially and then ductile after yielding (Potvin and Hadjigeorgiou, 2020). With respect to support design, a ground support system has to create a safe working environment under both static and dynamic loading conditions by providing the functions of reinforcing, retaining, holding and connecting elements (Cai and Kasier, 2018). Rigid rock bolts and cable bolts perform reinforcing and holding functions of a ground support system. In highly fractured ground or with large excavation spans (eg at roadway intersections or in caverns), unstable ground depth can exceed the length of typical rigid rock bolts (ie greater than ~3.0 m). In such cases, flexible cable bolts are needed to tie the reinforced and retained rock mass back to deeper and more stable rock. The flexibility of cable bolts allows anchor lengths greater than the tunnel opening that would otherwise restrict rigid bolts. Cable bolts also offer higher strength to weight ratio, with tensile strengths 2–3 times that of standard rebar bolts. This high strength comes at the cost of lower strain tolerance, typically around 5–7 per cent at break. Despite the lower strain tolerance, cable bolts are often used as dynamic support in demanding burst-prone ground conditions. The lower strain tolerance is compensated by allowing sufficient free length for stretching or incorporating a yielding device. There are a number of dynamic cable bolts available on the market and a number of testing campaigns have been undertaken to quantify the dynamic performance of these cable bolts. This paper reviews the existing range of dynamic cable bolts and discusses the potential areas for improvement and further research.

Nov 29, 2022

Sampling and sample preparation systems at the Hamersley Iron Pty. Limited port of Dampier, W.A., were developed for two separate objectives. 1. The need for rapid determination of physical properties. On stream size analysis enables lump ore and pellet- ized ore physical properties to be monitored and controlled whilst shiploading is in progress. As a control procedure this facility allows optimum shiploading rates con sistent with physical quality control. 2. The need for accurate chemical analysis. Chemical analysis on ship- loading forms the final link in overall quality control procedures encompassing the operation of mining, railway and port blending. Thus maintenance of specification products with minimum variation in chemical characteristics is ensured.

Jan 1, 1976

By D B. Donato

Gold mining cyanide-bearing solutions can pose a risk, cause significant wildlife deaths and adverse public relations and result in non-compliance with regulatory conditions. The International Cyanide Management Code for the Manufacture, Transport and Use of Cyanide in the Production of Gold (the Code) was developed as a voluntary code to encourage industry-wide improvements in managing cyanide responsibly. The Code requires design and implementation of robust monitoring programs for compliance under the following standards of practice: 4.1, 4.4 and 4.9. A robust monitoring regime can be complicated as each processing and tailing system is different. The following systems are commonly used in Australia: carbon-in-leach (CIL); carbon-in-pulp (CIP); heap leach process ponds; tailing waste disposal systems; peripheral discharge, central discharge and in-pit disposal. Some terrestrial wildlife can be denied access by fencing tailing storage facilities (TSFs) or other physical barriers, therefore limiting wildlife interaction with cyanide-bearing tailing and solutions to mainly birds and bats. While wildlife monitoring programs for processing and TSFs contain similar core attributes, it is necessary to adapt monitoring to take into account the site-specific features of each system. These core attributes are discussed in this paper, with reference made to cyanide concentration and associated methodologies. The issue is considerably complicated if tailing solutions are deemed or discovered to be toxic to wildlife. Essentially cyanides are required to be measured to gain an understanding of the concentrations to which wildlife may be exposed. This usually equates to measuring the cyanide concentration of solutions entering and leaving a tailing system. To assess the risk to wildlife presented by tailing and heap leach systems it is necessary to monitor both the hazard (cyanide concentrations) and the exposure (live wildlife species, presence and interaction). These tasks need not be arduous and a system of simple frequent monitoring has been developed and implemented for Code compliance. The wildlife monitoring developed by Donato Environmental Services (DES) and used at mining operations departs from the industry norm. It documents observer effort, live wildlife presence, habitat and behaviour in a tailing system, as well as deaths and carcasses. A greater understanding of wildlife cyanide toxicosis associated with this monitoring approach will enable mining companies to adopt a proactive approach to significantly reduce, or preferably eliminate, the impact on wildlife and assist in gaining Code compliance.

Jan 1, 2007

The purpose of this paper is to outline the basic policy problems for good community relations programmes in the resource extraction industries of Papua New Guinea. The main focus of the paper will be on defining and analysing those problems which lie on the landowner side and which are still not widely understood within the resource extraction industries despite several decades of turbulent experience. Many of the companies operating in the resource extraction industries of mining and petroleum and gas have in recent decades adopted, by choice or necessity, 'good corporate citizen' policies. Some of these companies now pursue ethical business, environmental and community relations policies. Some have adequately funded and well-trained staff in their community relations departments. Although different industry sites scattered over Papua New Guinea show significant differences in their experience of social conflict, I argue here that a good deal of this variation has less to do with the differences between the companies' public relations policies and their effectiveness and more to do with the conflict causing features of indigenous society. Experience suggests that even a company well-equipped with good intentions, good policies and good staff may experience serious difficulties in maintaining good community relations in Papua New Guinea. Many of these difficulties, I argue, can be traced to causes that lie, essentially, within the structure of Papua New Guinean communities and in the customs and social relations of Papua New Guinean peoples. Accordingly the attention of this paper is focussed on the conflict causing aspects of Papua New Guinean society. It is true, to the point of being a cliche, that Papua New Guinean societies are oriented very strongly towards achieving consensus and social harmony. In this regard Papua New Guinean communities differ significantly from, say, Australian communities. My purpose here is not to denigrate this aspect of Papua New Guinean societies but, rather, to point out that the drive for consensus is driven by the desire to avoid its opposite, dissensus. This paper sets out to define the dissensual aspects of Papua New Guinean societies and my special interest is in those conflict producing aspects of Papua New Guinean societies that are most resistant to the mechanisms that are designed to create social harmony. A survey of the recent history of industry and community relations in Papua New Guinea indicates that there are three main factors present on the landowner side which are liable, separately or through their interaction, to cause difficulties. These factors are respectively generational challenge, social boundaries and custom variability and I shall discuss each of these in turn.

Jan 1, 1997

By Stevens P

The Isa Mine of Mount Isa Mines Limited currently produces 5.4 million tonnes of copper ore and 3.3 million tonnes of silver, lead and zinc ore annually. Of this, 5.1 million tonnes of copper ore and 2.2 million tonnes of silver-lead-zinc ore is produced by sublevel open stoping. This paper summarises the capabilities, operating practices and problems encountered with current production drilling practices used to drill sublevel open stopes at Mount Isa.

Jan 1, 1982

The Government Mining Engineer of South Africa has decided to legislate that Self Contained Self Rescuers (S.C.S.R.) become a mandatory piece of equipment for all those persons proceeding underground. It is envisaged that: * employees in underground coal mines will be fully equipped with S.C.S.R.s during 1988; * those persons employed in gold mines during 1988/89; and * personnel in all other mines by the end of 1990. It is the intention of this paper to discuss the introduction of these auxiliary life support systems, and to give an update on current market developments.

Jan 1, 1988

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By R W. Wilson, A R. Branch, T S. Pooe

The original bulk air cooling system at this particular mine made use of two water chilling refrigeration machines to produce peak cooling of approximately 12 MWR with a downcast air temperature of about 7°C; however, as the shaft is not used for transporting personnel, the opportunity existed to supply more cooling to the mine by lowering the downcast air temperature. An ice storage facility has been constructed and provides a range of opportunities in operating the system: colder air temperature sent to the shaft, enabled by using near-zero degree water produced by melting ice to cool the air; electricity time-of-use management, by shifting electricity usage out of peak tariff periods; and increased peak cooling capacity, by melting ice while chilling water. Ice is created in the storage facility at night while the ambient air temperature is low and then melted to produce cold water when required by the cooling process. An ice dam was constructed and serpentine stainless steel coils installed where the ice is produced; one of the refrigeration machines was converted to chill a glycol solution to subzero temperatures to create the ice on the coils; a plate heat exchanger was installed to allow the glycol chiller to act as a water chiller as well; and a third spray stage was added to the bulk air cooler to utilise the near-zero water. This paper describes the thermodynamic design, construction and performance assessment of the new system, which is unique, novel and represents the state-of-the-art of this type of cooling system and energy management.CITATION:Branch, A R, Wilson, R W and Pooe, T S, 2015. Novel use of ice thermal storage for energy management on a mine refrigeration plant, in Proceedings The Australian Mine Ventilation Conference, pp 185–192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The Drummond Basin is a large intracratonic basin which developed in central Queensland during Late Devonian to Early Carboniferous times. It is postulated that the Drummond Basin developed as a foreland basin, to the west of a probable west dipping continental margin volcanic arc and subduction zone. The Drummond Basin sequence has been s,ibdivided into three tectono-sedirnentary cycles. Cycle I forms the base of the sequence and comprises thick sequences of intermediate to felsic volcanics and proximal volcanolithic sediments. The volcanics, particularly in the northeast of the basin, occur in separate sub-basins around what were probably isolated eruptive centres. In contrast, the rocks of Cycle 2 and Cycle 3 have been deposited during episodes of broad, basin wide subsidence. Five major igneous episodes, some of which may be co-magmatic, are recorded in the eastern Drummond Basin and environs between the Late Devonian and the Early Permian. The first and second episodes occurred during the Late Devonian to Early Carboniferous and are represented by the volcanics in Cycle 1 and Cycle 3. The third episode involves the intrusion of granitoids of Early Carboniferous age into the Drummond Basin sequence. These occur in the Ukalunda area and are related to gold mineralisation at Ukalunda and Valhalla. Episode four includes the felsic volcanics of the Bulgonunna Volcanics. This episode does not appear to he broadly auriferous but gold mineralisation does occur in possible basal Bulgonunna Volcanics at Mount Coolon. The final episode includes a suite of granitic intrusives which intrude the Bulgonunna Volcanics and which are considered to be co-magmatic with them. These intrusives do not appear to be generally associated with gold mineralisation. Gold mineralisation is widespread in the north- eastern Drummond Basin and environs. It is probable that the gold mineralisation is concentrated in epithermal cells during the Late Devonian to Early Carboniferous volcanic cycles. This style of mineralisation appears to be related to tectonic setting in modern analogues.

Jan 1, 1989

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

Over the past seven years, a combination of New Zealand-, Australian- and German-led research voyages using the research vessels Tangaroa, Southern Surveyor, and Sonne respectively, have revolutionised our understanding of the Kermadec-Tonga arc-backarc systems. This convergent margin is the most seismically-active subduction zone system on Earth with convergence rates steadily increasing northwards from the Hikurangi Trench to ~250 mm/year at northern Tonga. In combination with the intra-oceanic setting, factors potentially producing magmatic, tectonic, and hydrothermal variability in this system include an increase in potentially subductable sediment northwards along-strike, intersection of the Louisville Ridge (hot-spot chain) and Osbourn Trough (paleo-spreading centre) with the arc at ~25¦S, and the possibility of Samoan (hot-spot) plume ingression in the northern Lau Basin. The bulk of the magmatism is submarine; whereas only a few emergent (some transient) volcanic islands exist, about 80 submarine volcanic centres of significant size (>1000 m above surrounding sea floor) are present between White Island in the south to north of Tafahi in Tonga. About 35 per cent of these centres are hydrothermally active. Important petrogenetic features of the volcanic rocks along this arc system are the abundance of rhyolite (some quartz-amphibole-bearing), and the outcrop of primitive olivine-clinopyroxene-phyric basalts in satellite cones of the major edifices. Many of the edifices consist of complex caldera systems. Eruptions from and degradation of these edifices were probably tsunamigenic. Many of the hydrothermal systems developed within the edifices are likely destroyed during the sector collapses which are the characteristic edifice degradation mode. There are three backarc spreading systems along this margin: the Havre Trough, Valu Fa-Eastern Lau Spreading Centre, and the nascent Fonualei Rifts. The latter are particularly notable in having captured the entire suprasubduction zone magmatic flux for a distance of about 150 km, shutting down the adjacent volcanic front arc volcanoes.

Jan 1, 2005

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007

By P Mitchell, S Pushpan, G Ferres, K Bobbermien, L Hudson

"Falling commodity prices and a rising supply surplus have ushered in a period of restraint in capital project investment across the global mining and metals sector. Competition for capital project funding has seen fewer projects progress through investment gates and a stronger focus on projects that deliver gains in capital productivity and strategic outcomes.Over the course of the 2015 financial year, EY conducted a study of 108 projects in the global mining and metals sector (EY analysis; Larsson and Ericsson, 2014; SNL Financial, 2015). The projects studied were at various life cycle stages and related to the development of copper, iron ore, gold, coal, nickel and other commodities. Each individual project investment exceeded US$1 B, and the studied group represented a cumulative investment value of US$367 B.The research found that the majority of projects were delayed and/or over budget when measured against the initial estimates made during the early stages of the project life cycle. Of the surveyed projects, 69 per cent were identified as facing cost overruns with an average overrun of 62 per cent above the initial estimate and 50 per cent reported schedule delays, even after remedial acceleration initiatives.The analysis found that budget and schedule overruns could be attributed to five key causes:project management factorsstakeholder conflictsresource constraintsregulatory, and policy-related challengesunfavourable external environment.Improving project delivery performance starts with successful planning, followed by rigorous management during delivery. From global experience on large and complex capital programs, EY has observed a consistent theme of underinvestment and a lack of focus in three often-overlooked but critical areas:implementing effective governance and reporting frameworks with lead indicators that reliably flag emerging risks while they can still be mitigatedallocating adequate cost and time contingency to account for risks across the life cycleenhancing the value of contingency by aligning contingency plans with scenario plans.This paper explores the surprising findings of the study, proposes a root cause model and examines key considerations in applying these critical enabling techniques.CITATION:Hudson, L, Mitchell, P, Ferres, G, Bobbermien, K and Pushpan, S, 2016. Are your megaproject schedules and costs under – or out of – control?, in Proceedings Project Evaluation 2016, pp 75–85 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By A Tawadrous, B Wheeler, D S. Preece, S A. Silling

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Moving rock with explosives rather than mechanical equipment can improve mining efficiency. Such is the case with coalmine cast blasting. Controlling and directing rock movement through explosive deck delay timing can greatly improve ore recovery by segregating ore and waste. In both cases, understanding, predicting and controlling heave is an important element of successful blasting.Computer programs for predicting 2D blasting-induced heave have been used in mining for decades, helping to drive the innovation of new and more efficient mining methods, ie cast blasting. The past few years have seen the advent of 3D distinct element modelling of blast-induced heave. This is an important advancement because most blasting situations are three-dimensional in nature, especially when controlling the direction and intensity of rock movement through explosive deck delay timing.This paper documents the first full-scale blasting simulations in 3D with distinct element models that include hundreds of blastholes and in excess of a million particles, made possible with parallel processing. Surface mineral blasting is the focus of this study which treats the effect of blasthole delay timing on ore recovery. Ore waste and dilution resulting from typical row-on-row delay timing will be demonstrated. Also demonstrated will be the ore recovery possible with delay timing designs that significantly enhance ore/waste segregation. This type of high fidelity modelling and the use of electronic detonators makes possible the sculpting of rock blasting muck into separate piles of ore and waste.CITATION:Preece, D S, Tawadrous, A, Silling, S A and Wheeler, B, 2015. Modelling full-scale blast heave with three-dimensional distinct elements and parallel processing, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 127–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Vutukuri VS, Budavari S

During recent years many investigators have suggested large spacing to burden ratios to improve the fragmentation obtained in blasting. In spite of these suggestions, most operators still use a conventional ratio of 1 to 2. From single hole longitudinal charge tests in laboratory, it is shown that burden controls the fragmentation. The burden for obtaining uniform fragmentation is smaller than the burden to obtain maximum breakage. Tests on two or three holes show that a larger spacing to burden ratio can be used for smaller burdens, but it is not possible for the larger burdens chosen to obtain maximum breakage. By using finite element analysis evidence is presented to show the effect of spacing and burden relationship on blasting results.

Jan 1, 1975

A method is presented for calculating the number of cycles of stress to failure of a drill rod from operating variables; a mathematical analysis by Cooper of the stresses present in drill steels is applied to the forged collar, i1i-in. hexagonal hollow drill steel in common use in Australia; and an estimation is made of the dry fatigue limits at various points along a drill rod.It is shown that these calculations predict failure at a 'point where failure rarely occurs, and do not predict that failure should occur where it does in practice. The reasons for this anomaly lie in the neglect of bending stresses in the stress calculations, and in failuredue to corrosion fatigue at a preferred section rather than to simpler fatigue under non-corrosive conditions.INTRODUCTIONIt has long been recognized that failure of metal sections by fatigue is influenced both by the number of cycles of stress imparted to the section (N) and by the magnitude of this cyclic stress (8). In this paper, both Nand Shave been calculated for rods which have failed in service, and whose operating history is known. While the calculation of the number of cycles to failure is·simple, the calculation of stress is more complex. The results of stress caIculations predict that failure should occur only hi short rods, and then preferentially at the tip end rather than the shank end.However, in actual fatigue failures of steel rock drill rods, approximately 75 per cent. of such failures are close to the shank end, and failures near the tip end are rare.The usual explanation given for this high incidence of shank-end failures is that at the point of failure there exists, in forged collar steels of the type common in Australia "hardness valley" or. "m'etallurgical notch". This narrow valley in hardness is a weakness, and failure is expected to occur at the weakest point at the bottom of...

Jan 1, 1955

By P Gilroy

In recent technical investigations that were triggered from ore for rail shortfalls at Yandi, BHP Iron ore has identified a gap in resource knowledge relating to geo-metallurgical characteristics that predict materials handling performance and throughput. Within these investigations BHP has learnt that this lack of resource knowledge has translated to a lack of predictability associated with mine planning inputs which has resulted in poor compliance to plan and deviation management practices. A business value chain was developed in an attempt to identify the best possible solution to unlock this resource knowledge in the short, medium and long term planning horizons. A fast fail approach was taken with the implementation of hyperspectral blasthole analysis, which was chosen to deliver the best possible value driver for the asset. This report will detail the Yandi journey in expanding the hyperspectral and geo-metallurgical value chain, unlocking resource knowledge along the way. CITATION: Gilroy, P, 2018. Development of an empirical geo-metallurgical model that unlocks value of the mineral resources at Yandi Mine, in Proceedings Complex Orebodies Conference 2018, pp 85–87 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By J Fewings, T McCredden, S Seet, C Fitzmaurice

"Flotation of nickel sulfide ores are generally constrained by nickel grade and impurity concentrations (notably magnesium and arsenic) in the product delivered to smelters. Being a physical separation process, flotation recoveries and grades are limited by the grade recovery curve of a particular operation, where increasing product grades are invariably associated with lower recoveries. Impurities put further pressure on this relationship, as removal of impurities from the final concentrate is almost always associated with nickel losses.Western Areas Ltd are developing a proposed expansion to its Cosmic Boy concentrator to treat an impurity stream, that is high in nickel and would otherwise report to tails. Through the use of BioHeap® technology Western Areas aims to recover the nickel and discard the arsenic to tailings. This expansion will consist of a biohydrometallurgical plant that leaches the nickel arsenic minerals, removing the arsenic as a stable iron/arsenic hydroxide, while recovering the nickel as a high-grade nickel sulfide product (at approximately 50 per cent nickel). This can then be blended with final concentrate to improve nickel grades and recoveries, while simultaneously reducing impurity levels or used to produce high value products like nickel sulfate.The introduction of a small microbial leach plant may be beneficial to base metal concentrators constrained by impurities or grade.Citation:Fewings, J, Seet, S, McCredden, T and Fitzmaurice, C, 2016. BioHeap® - Breaking the Grade/Recovery Curve for Nickel Concentrators, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 361–368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By Percival T. J

Precious metal deposits containing fine-grained disseminated or dispersed gold-silver form by reactions between metal-bearing hydrothermal fluids and sedimentary host rocks. Host rock permeability and chemical composition exert a primary influence on the fluid movement necessary for any primary dispersion halos to form around ore bodies, and determine whether a disseminated style orebody itself will even form. Where the mineralized rocks are relatively unfractured the margins of the orebodies exhibit abrupt decreases in gold content, and strong corresponding decreases in the contents of other metals. Primary dispersion patterns of this type are difficult to recognize and commonly are only a few meters (or less) in width. If the host rocks were well shattered and broken before mineralization, remnant amounts of the hydrothermal fluids may be dissipated in fractures lateral to or above the ore zones. This causes geochemical anomalies to form with clays and silt- size silica within the fractures over distances of up to at least 30-50 meters away from the main orebodies. The tendency for large primary dispersion halos not to form around these deposits explains the disappointing results from so many drilling programs where no multi-gram gold-grade material was even found: if large areas and apparent large volumes of rock contain one gram or less gold that likely is the "orebody" and not a halo effect around high grade mineralization.

Jan 1, 1988

By W Stange, N Hanson

An important aspect of the project evaluation process is the achievement of a clear and quantitative understanding of the primary drivers influencing project value and risk. A business scenario-based approach is required to ensure that the project meets value and risk hurdles over the short, medium and longer term. Adopting an optimising approach can aid significantly in the development of a project concept into a business that is optimal and sustainable in the longer term. Through the application of case studies, based on work performed with various mining organisations during the last five years, this paper will demonstrate how project value and robustness can be optimised. Experience has demonstrated that applying this approach results in significant value improvements and risk reduction û primarily by application of a rigorous, fact-based analysis and optimisation process that rapidly increases management team understanding and insight of key driver of value and risk.

Jan 1, 2007