Search Documents

By Van Rooyen F

An introductory review of the current grade control blasting techniques (selective mining strategies) used in the Eastern Goldfields has recently been undertaken. The survey was initiated and conducted by the Western Australian School of Mines. Four distinct selective mining strategies have been identified and a number of trends have been highlighted. Many operations, however, have developed techniques which use a hybrid method to suit the site conditions. The aim of all the mining strategies is to produce an optimum product. The optimum product is one which contains no diluent and experiences no mixing of the various identified ore and waste blocks and is fully reco- vered at the minimum overall operating cost. Due to this unified aim all of the grade control blasting techniques have many common design Features.

Jan 1, 1988

By A Mcquillan, N Bar

Geotechnical models developed during the open pit mine planning stage are generally three-dimensional (3D) in component to capture the spatial variation in geological, structural, hydrogeological and geomechanical conditions. Yet when geotechnical analysis is completed, often the 3D geological, hydrogeological and structural models are simplified to two-dimensions (2D). This paper demonstrates this simplification, through referenced case studies, can lead to the wrong failure mechanism being analysed and/or a conservative Factor of Safety (FOS), or Strength Reduction Factor (SRF), being calculated, leading to a false sense of stability. There exists a paradigm that the FOS calculated using 2D limit equilibrium (LE), or the Strength Reduction Factor (SRF) calculated using 2D finite element (FE), modelling methods is generally conservative, ie lower, than the true FOS. However, this assumption that 3D FOS, or 3D SRF, is always higher than 2D FOS, or 2D SRF, is not always correct (Chen and Chameau, 1983; Bromhead and Martin, 2004; Herza et al, 2017; Pyke, 2017; Dana et al, 2018).

Nov 29, 2022

By Thornber MR, Davidson LR

The cause of spontaneous combustion of pyritic black shale has been studied by calorimetry and other techniques. The conditions required for ignition to occur are: 1. A critical mass of pyritic black shale. 2. Acidity. 3. Fine shale particle size. 4. A high ambient temperature. 5. The exclusion of air during the preparation of a calorimeter charge. The reaction is characterised by an initial incubation period during which an unknown phase is produced. The build up and oxidation of this phase results in a chain reaction culminating in ignition. The mechanism is believed to involve the interaction of pyrite, sulphuric acid, ferrous sulphate, or meta-stable oxysulphates, with ammonium nitrate. The recommended strategy for prevention of premature detonation is to neutralise the acids in the shale with quick and slow release alkaline materials.

Jan 1, 1986

University education in Australia is changing, driven by greater market orientation, reduced funding available per student, especially in the higher-cost minerals industry disciplines, and the call for more flexible delivery of subjects and courses to meet changing lifestyles and expectations. The opportunity exists for a true partnership to develop between industry, government and academia that will reshape minerals education in Australia and secure the future supply of the specialists industry needs to maintain international competitiveness. If this partnership does not emerge, it is anticipated that AustraliaÆs somewhat fragmented and unstable higher education system, especially in the disciplines of particular relevance to the minerals industry, will be put under further pressure so decreasing its effectiveness to produce quality graduates. The Minerals Council of Australia in 1998 published æBack from the BrinkÆ, a discussion paper which proposed strategies to build a world class minerals tertiary education system in Australia. Those strategies are now being implemented collaboratively with principal emphasis on the disciplines of mining engineering, metallurgy and earth science and as far as process is concerned, on the necessity to æcooperate to competeÆ. For metallurgy, the challenge is to integrate more closely undergraduate teaching with the existing world-class research centres and to link the tertiary institutions in such a manner that the strengths of all components are harnessed and then made available nationally in major population centres and at remote sites where appropriate. For industry the challenge is to build effective partnerships with the academic community that will enable and assist the agreed course of action to take place.

Jan 1, 2000

By Bruce P, Luyendyk

The South Island of New Zealand comprises a collage of distinct tectonostratigraphic terranes. Some tectonic models predict that these terranes formed on or near the margin of Gondwanaland. However, geologic evidence suggests that some of these terranes may be exotic. Over 400 samples from 30 sites were collected from the Brookstreet terrane within the Takitimu Mountains. The section includes the early Permian Takitimu Group and the late Permian White Hill Intrusive Suite. Over 80% of the rocks show a partial or complete regnetization in the present field due to recent acquistion of VRM. Although some remagnetization of the Takitimu Group occurred during the emplacement of the White Hill Intrusives, both early and late Permian direction have been isolated. These directions indicate a mid-latitude origin for the Brookstreet terrane, and suggest a strong clockwise rotation between early and late Permian time. A published paleomagnetic result from the younger, but related, Murihiku terrane suggests that the Brookstreet terrane was sutured to the margin of Gondwanaland by the late Triassic, or that the Brookstreet and Murihiku are two distinct terranes.

Jan 1, 1987

The Newcrest Mining Limited Telfer Gold Mine consists of an underground sublevel cave (SLC) operation located 734 m directly below active open pit operations. Open pit and underground current production rates are 50 million and 5.7 million tonnes per anum (Mt/a) respectively. The SLC was initiated in late 2006 with breakthrough planned to occur on the 5484 bench of the west wall in late 2009. Risk to the south ramp was identified during this time, resulting in the construction of the north ramp. The SLC was continually tracked from initiation with a suite of monitoring systems and managed with a Major Hazard Management Plan (MHMP) and associated Trigger Action and Response Plans (TARP). At breakthrough the eastern limb of the cave was located within a 70 m horizontal distance from the south ramp. The south ramp was closed in October 2009 due to significant slope deformation, extensive cracking in the berms and batters between the ramp and breakthrough bench and a major failure 250 m to the north of the cave breakthrough. Wall response was first identified from slope deformation measurements taken by the wall monitoring radar in May 2009, at which point the SLC was 160 m from breakthrough. The impact of the SLC on the slope is a unique case with the monitoring systems in place able to provide data on the slope reaction to the SLC progression. This paper will discuss the management of the south ramp such as the early interpretation of risk associated with cave breakthrough, monitoring systems implemented to track the cave progression and wall deformation, data integration and interpretation and risk management. Following the closure of the south ramp further instrumentation programs and risk assessments were conducted to determine the risk of re-opening this haulage route. The outcomes of this program will also be presented.

Nov 25, 2010

By J Levett, O Rondon, I Glacken

Reporting Codes are not prescriptive on methodologies to report or classify Mineral Resource Estimation results, but the assessment of risk and uncertainty is required, and is likely to be increasingly important in future Code updates. The 2012 JORC Code indicates that relative confidence in tonnage-grade estimations should be considered for classification, and that there should be a discussion of relative accuracy and confidence levels in the Mineral Resource Estimate. These considerations are also relevant to the drill hole spacing required for various classification categories, along with other geological and data quality criteria. This paper summarises the theory, principles and current practice of various drill hole spacing analysis techniques for both achieving a desired level of resource categorisation and for optimising grade control or resource drill-out costs. The authors provide practitioners with a guide in their use to assess uncertainty and relative accuracy, as illustrated by a number of case studies. While all drill hole spacing studies rely on the assumption of consistency of the continuity model from current to future drilling, the range of methods available provide much more objective outcomes than previously adopted ‘rules-of-thumb’.

May 24, 2023

By C B. Smith, G L. Boxer, S W. Moss, A L. Jaques, V Lorenz, M J. Rayner

The Ernest Henry Iron Oxide Copper Gold deposit is hosted in a large dilation between two moderately dipping shear zones found in the footwall and hanging wall of the deposit. These shears are controlled by a large diorite intrusion to the north-east and south-west of the deposit, formed ~1660 Ma. A shear zone dubbed the ‘Interlens’ uncovered through underground workings truncates the main orebody into two lenses, and is hypothesized to have formed in conjunction with the Hanging Wall Shear Zone and Footwall Shear Zone. All three shears dip moderately to the SSE (50–140) from open cut exposures through to the current mining horizon approximately 800 m below the surface. Routine geological work and a capital drilling campaign has identified a significant flexure in these sub parallel ore bounding shears with increasing depth. A shift in shear orientation in the Interlens over approximately 100 m vertically from ~50° to the SSE to a steep, easterly trend (~85° to the east) is observed in both drill core and exposures in the underground workings. It is hypothesized the diorite intrusive to the south-west of the deposit controls the shear zone geometries at depth. The geometry of the Interlens mirrors the surface expression of the Proterozoic package of the orebounding shears to the south-west of the deposit, suggesting the surface geometries of the shear zones are consistent with depth. Additional drilling to explore the validity of this hypothesis is planned for the near future to better understand the structural controls on the Ernest Henry mineralisation with increasing depth.

Mar 22, 2022

By McCarthy P. L

With production at Olympic Dam scheduled to commence in June 1988, it has been necessary to install a complete underground ore handling system capable of removing two million tonnes of material annually from the mine. The system comprises mucking from stope drawpoints, truck haulage to underground storage, primary crushing, conveying and hoisting. On the surface, material is conveyed to stockpiles at the Metallurgical Plant. Mining of the numerous special excavations within the system was incorporated into the mine's ongoing development program prior to the underground construction phase. Utilisation of a decline from the surface enabled versatile construction equipment to operate at the underground sites as well as simplifying the transportation and delivery of construction Materials.

Jan 1, 1988

By Ciminelli VST

Thiourea leaching has been applied to a refractory gold concentrate previously treated by bacterial oxidation. Following the bio-oxidation, gold has been leached in acidic thiourea solutions, under different pH(1 - 2.4), thiourea concentrations (2 - 15 g/1), ferric ion concentrations (0.04 - 3 g/1) and temperatures (298 - 333 K). Through this procedure, it was possible to increase gold extraction from 40 to 77 per cent. The increase in temperature raised gold extraction and reduced reagent consumption. Sodium sulphite addition was also very effective in lowering thiourea consumption. Staged leaching operations with interstage acid washing and carbon-in-leach experiments were tested, in an attempt to increase gold extraction. The results of thiourea leaching were compared with those obtained with cyanidation.

Jan 1, 1993

By L M. van Niekerk

The mining of iron ore is a high volume low margin business because the value of this commodity is significantly lower than that of base metals. The main metallurgical challenges in most of the iron ore projects proposed for treatment nowadays have been in finding the optimum flowsheet for the treatment of magnetite ores, mixed magnetite-hematite ores and even ores that have banded ironstone formations (BIF). The associated plant designs incorporate very high capacity milling systems to grind the ore down prior to magnetic separation and in being highly capital intensive requires substantial investment in mega processing plants with associated infrastructure to mill down the run-of-mine ore to the desired treatment size for upgrading.To minimise the cost of infrastructure, better beneficiation techniques and technologies are being sought to assist in reducing upfront ROM feed to allow for reduction in overall treatment plant footprint necessary in extracting the desired downstream product. This paper discusses such beneficiation techniques and advancement in technologies for the upgrading of coarse and fine iron ore utilising dense media separation (DMS), jigging, wet magnetic separation, dry magnetic separation, flotation and x-ray processing.Another group of iron ore projects involve the mining of hematite ore below the water table. Often the mined ore is wet and sticky. This combination requires high capacity processing of feed material utilising large scrubbers or attritioning units to effectively remove the slimes component present in the feedstock. The fines removed, usually below 1 mm, are then discarded in large tailings storage facilities. Approaches to recovering the saleable material contained within these fines will also be investigated in this paper. This not only implies possible reduction in slimes discard footprint, but also holds potential benefit in augmenting overall yield and recovery of hematite product.CITATION:van Niekerk, L M, 2013. Fine and coarse iron ore beneficiation - An evaluation into global technologies and techniques, in Proceedings MetPlant 2013 , pp 584-598 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By B King

A large number of mineral deposits contain regions in which it is economically beneficial to extract ore both via open pit and underground mining techniques. Current industry practice lacks an effective means to establish the extent of the open pit and underground mining areas for an individual deposit. We present a mixed integer programming model for scheduling both the open pit and underground mine that can be used to create a holistic extraction sequence for a specific deposit. The model considers both spatial and temporal elements of the open pit and underground mines in order to maximise the net present value of the entire deposit, while adhering to its production, processing and block sequencing constraints. By doing so, we can schedule the open pit and underground in concert.CITATION:King, B, 2014. Modelling open pit and underground production scheduling in concert, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 369–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By A E. McElnea, M A. Martens

An 18-month project was undertaken to test the effectiveness of controlled daily tidal exchange augmented with hydrated lime treatment of surface waters as an approach for remediating a severe acid sulfate soil disturbance at East Trinity, Cairns, north Queensland. Actual acid sulfate soils were producing hazardous levels of acid and heavy metal contaminants and degrading approximately 720 of the 940 ha East Trinity property and the adjacent foreshores. A government-led research team established a series of research projects with the aim of characterising the site (soils, water, terrain) and testing the effect of the lime-assisted tidal exchange management strategy on soils, water, sediments and biota.

Jan 1, 2003

By A Melloy, D Holt, M Jurak

Oaky North is AustraliaÆs highest producing underground coal mine. In 2011, the mine produced 8.7 Mt of high-quality coking coal. The high quantities are a result of the constant strive for optimising the operating time of major production units, which involves investing numerous resources, including diesel equipment, in supporting and maintaining their operation.In July 2011 it was identified that the diesel particulate matter (DPM) levels in the underground workings were above acceptable levels, due to the high level of diesel activity. Over the next 12 months, several controls were implemented to reduce exposure to personnel: the main ventilation system was upgraded; the production forecast was adjusted to better manage the diesel fleet, removing surges in diesel usage; and an electronic diesel tag board was introduced to centrally manage the distribution of diesel usage around the mine.From the start of the campaign in emission reduction, an intense DPM monitoring regime was established. Within a few months of the introduction of the centralised tag board, there was a major reduction in emission levels. After the installation and commissioning of the new main fans, the emission levels dropped further, such that over-exposures are now a rarity.Oaky North continues to explore new systems to better utilise their diesel fleet while still maintaining control over DPM emissions.CITATION:Melloy, A, Holt, D and Jurak, M, 2013. Reduction in diesel particulate matter at Oaky North, in Proceedings The Australian Mine Ventilation Conference , pp 187-190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By R Zhang, J Xu, X Lv, C Bai, S Zhang

This paper studies the grinding behaviour of vanadium-titanium magnetite concentrate in a ball mill. The grinding kinetics, surface morphology, lattice distortion, wettability and moisture capacity were analysed. Grinding kinetics equation was established based on population balances model with the size distribution data from a laser diffraction technique. The SEM photos of the ground concentrate showed that the surface gets rough with increasing grind time. Agglomeration of fine particles was enhanced when the grinding time reached 30 minutes. X-ray diffraction results showed that a loss in crystalline occurred with increasing the grinding time. The peaks of the X-ray diffraction patterns are significantly broadened with increasing grinding time. Wettability, characterised by contact angle between the material and water, improved due to the fact that the surface roughness increased with increasing grinding time. Moisture capacity of concentrate ascends abruptly in the first three minutes and then changed slowly with increasing grinding time. The water transfer coefficient in the particles increased rapidly in the first six minutes and then decreased quickly until grinding time reached 12 minutes.CITATION:Zhang, R, Lv, X, Bai, C, Xu, J and Zhang, S, 2013. Wet grinding of ?vanadium-titanium magnetite concentrate in a ball mill, in Proceedings Iron Ore 2013 , pp 511-518 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By I Treloar, T Elenbaas, E Isaaks

Critical reviews of grade control generally focus on blasthole sampling and the estimation of ore control block model (OCM) grades, with little or no attention given to dig-line design. For example, the estimation of block grades is deemed important as estimation errors lead to the misclassification of ore types and subsequent dollar loss. Recognition of the problem that the underestimation of block grades may be more or less costly than overestimation led to the application of loss functions to the classification of individual OCM blocks by ore type. The method is known as maximum profit selection (MPS). However, each OCM block may be misclassified a second time by dig-line design. Although each block may initially be assigned an optimum ore type by MPS, OCM blocks are seldom individually mineable by ore type. As a result, a common solution to this problem is the design of mineable polygons or dig lines loosely constrained by a minimum mining width. All material within a properly designed dig-line polygon can be mined and sent to a single destination such as the mill, stockpile or waste dump. These dig lines are often designed manually or by simple variations of computer-generated contour lines. They are generally suboptimal and result in additional misclassifications of ore types. This paper provides an algorithm for constrained optimum dig-line design where dig-line misclassifications are also evaluated through loss functions or MPS. Constrained optimum dig-line designs minimise the dollars lost by dig line misclassifications for a given minimum mining width constraint. A case study is provided illustrating constrained optimum dig-line design and subsequent benefits.CITATION:Isaaks, E, Treloar, I and Elenbaas, T, 2014. Optimum dig lines for open pit grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 425–432 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Lee M. F, Guilfoyle K

A large hard rock rib pillar was recently preconditioned at Mt Charlotte mine using a novel blasting technique. The motivation for trialling this procedure was a history of past pillar failures, with associated seismicity. Design studies had shown that a new proposed pillar would be at risk of violent failure, and preconditioning was used in an attempt to reduce this risk. Preconditioning by blasting involves physically modifying a selected zone of ground in advance of mining, then forming the pillar so that it incorporates that zone of ground. The modified rock in the zone is intended to allow extra closure (yield) of the pillar in response to mining-induced stress changes. The ground modification was done by tight firing a blasthole array to fracture the rock. The blast design comprised pairs of pre-split blastholes to create a series of short cracks across the target zone, followed by main blastholes to fracture the rockmass between each pair of cracks. A monitoring program was used to establish whether or not the preconditioning was effective. It included conventional extensometers, stress change cells and closure stations, plus a seismic monitoring system. To-date, stoping is complete on one side of the pillar and has just commenced on the other. Results show significant movements within the preconditioned zone and on geological structures in the pillar, as well as lower stress in the pillar compared to an adjacent non-preconditioned site. The preconditioning technique can be applied elsewhere, provided its purpose, mechanism and side effects are understood. Benefits are likely to include more assured production, and successful pillar recovery even in high stress situations.

Jan 1, 1995

By A Finch, C Pridmore

The Cosmo Project falls within the Archaean to Palaeo-Proterozoic Pine Creek Orogen, one of the major mineral provinces of Australia.The Cosmo Deposit is interpreted to be a series of steep north-west-plunging gold mineralised vein, breccia and shear systems within the tight Howley Anticline and hosted within interbedded siltstones, mudstones, banded iron, phyllites, dolerite sills and greywacke.A folded environment poses a number of technical challenges, particularly for estimation.Handling of tightly folded and in some cases narrow domains might include subdomaining for orientation, omni-directional three-dimensional (3D) estimation within constrained domains or software-enabled unfolding/un-wrinkling procedures (transformation of the data and estimate space into a two-dimensional environment). Each technique has its own unique set of advantages and disadvantages.A further method (one applied at Cosmo) is where the estimation parameters (specifically search and variography orientation) are modified in a frequent or ‘dynamic’ sense to suit the orientation of the domain whilst maintaining 3D space. Control of the resource estimation orientation can be done in several ways, including the use of sectional panels of a specific size or, alternatively, orientation sector divisions. The sector approach provides some significant reductions in processing time over the panel technique and could be applied in a number of software packages.Three-dimensional ‘dynamic’ interpolation reconciles well with production data from Cosmo, whilst the sector method provides a practical technique that can be executed without the complications of transformation or the need for labour-intensive orientation subdomaining and with acceptable resource estimation run time.CITATION:Finch, A and Pridmore, C, 2014. Dynamic interpolation – estimation in a folded environment at the Cosmo Deposit, Northern Territory, Australia, in Proceedings Ninth International Mining Geology Conference 2014 , pp 107–114 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

The optimisation and validation of shearer cutting methods is a time consuming engineering task. Many different parameters, of which not all can be controlled, can vary. The easiest solution, to increase the installed power and the longwall length, is not always the best. A different cutting method can increase the capacity without the need of new machines. The Department for Mining and Metallurgy Machinery at RWTH Aachen University therefore developed ProSL, the simulation tool for shearer and longwall operations. ProSL enables the engineer to create his own cutting methods and compare it with other methods. Machine-data can easily be varied to see the impact on the method. The research shows that sophisticated longwall methods increase the productivity of the system. The paper presents the results of the calculation with ProSL and shows how higher efficiency and lower costs can be achieved.

Dec 6, 2010

By Morinaga K

The optical basicity (A, Pb2+ as probe ion) of various oxide glass systems has been measured to establish the new basicity scale of slag melts. Best conditions of glassy fragments to measure A were as follow, (1) 1 ti 4 x 10-2 wt% Pb content, (2) 0.2 mm in thickness, (ii) enough annealing (about 10 hr) at a temperature 200¦C below Tg., and (4) polishing a surface well. the variation of A with composition was correlated to that of relative oxygen activity of slag melts. The estimation of basicity of slag melts from it could be valid. The A of opaque and coloured quenched slags could not be measured. An approximately linear relationship, however, exsisted between the isomer shifts (b) of Fe3+ ion in slag derived from the Mossbauer effect and A. Therefore, -4 of various metallurgical slag could be estimated from this relationship. These results can be expected to establish the new basicity scale of slag melts as the Louis basicity.

Jan 1, 1980