Search Documents

Open pit mining at Bingham Canyon commenced in 1904 and about two billion tonnes of ore have been extracted since then. There remain just under one billion tonnes of ore in the pit and this will be mined by 2015. Because the porphyry system extends below the ultimate pit limits, Kennecott Utah Copper Corporation initiated a study in 1997 to determine the viability of underground mining. The study was initiated at that time because the results were to be used to compare the economics of a further pit expansion to that of an underground mine. If a pit expansion was viable then overburden removal would have to start in the near future. This paper is a summary of the work that was carried out for the underground study. Block cave mining was determined to be the most appropriate method to mine the deposit. Two block cave areas have been planned with a total production rate of 72 500 tpd. Additional sources of ore will come from skarn orebodies that are associated with the porphyry deposit. The geology of the deposits is described together with the geotechnical techniques that were used to characterise the rock in the absence of more detailed data that are normally available. A general description of the mine plan is given along with the reasons for selecting the particular methodology used. The study was completed at the end of 1998 and demonstrated the viability of underground mining at Bingham Canyon. Funds have been approved for further drilling and technical studies, which will lead up to a feasibility study in 2004/5.

Jan 1, 2000

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By Lynce AJ

A method has been developed for the prediction 'of 'the- . performance of a multi-stage grinding=cyclone classification circuit of any degree of complexity on any ore for a wide range `of operating conditions, The-.method involves ;the. s` inu ation b'f the circuit on a digital computer by means of. matheinatical' models ":bf the"' individual units:, the. development of which is- also discussed'., At present, in order to establish 'the!'" charac'teristtics of they ¦ore- and the machines. in mathematical terms;. it is necessary to know'the performance of a , simpl,.e. ; system on tri.e ore - for! one known ,,feed rate and.fe.ed s,l-zing, analysis. ' ,Fiiither work on :the- separate identification 'of the terms defining the characteristics of the ore and the machines may permit the method to be, applied directly to the cj.4ta,derived from small scale tests on ores,

Jan 1, 1964

By D Lees, D Gilchrist

Sydney has hundreds of kilometres of sewer tunnels. Many of these are over 50 years old and some have been in service for more than 100 years. The tunnels are predominantly constructed in Hawkesbury Sandstone and many are unlined.Principles have been developed over many years for the safety factor required in designing and constructing new tunnels but these do not necessarily relate to the operation and maintenance of existing tunnels, and in particular those that do not necessarily require personnel access for anything other than regular inspections.Assessment of the stability of these established tunnels needs to take account of their size, their age, their function, and their method of construction, as well as the geology in which they are situated and any support measures which have been installed. More importantly a stability review needs to take account of the consequences of a collapse, with regard to the inspection process, carrying out of any required repairs and the long-term performance of the tunnel.This paper is based upon the authors’ experiences inspecting and reviewing more than 200 km of tunnel in the last ten years. It will show some of the procedures and methods adopted by Sydney Water, how these can be presented as an acceptable procedure in line with other safety standards, and how they might be adopted for other similar historic rock tunnels.CITATION:Gilchrist, D and Lees, D, 2014. The development of a procedure for the inspection of unlined rock service tunnels, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 543–552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health rleterinratinn_

Jan 1, 1988

By S Gezgin, F Beckstein, M Müller, D Rapp, D Sergeev, J Qi, A Lichtinger

Salts and their mixtures play an important role for industrial and energy sectors, eg metallurgy, biomass gasification and combustion, nuclear and solar powerplants and electrochemical processes. Depending on the composition of salts (eg Li+, Na+, K+, Mg2+, Ca2+ // NO3-, F-, Cl-, CO32-, SO42-, etc), the temperature range for different applications can vary starting from room temperature and going up to 1500°C. For the proper design and modelling of heat exchangers and other equipment, it is necessary to have reliable and validated data sets of thermophysical properties. The 50 mol per cent NaNO3 – 50 mol per cent KNO3 salt mixture as a well-studied composition was selected for validation of relevant thermophysical properties (heat capacity, enthalpy of phase transitions, thermal expansion, viscosity and thermal conductivity). To study these properties of the liquid phase, special crucibles and approaches should be implemented. Verification of these crucibles for different methods (differential scanning calorimetry (DSC), thermomechanical analysis (TMA), laser flash analysis (LFA) and rheometers) has been performed. The low thermal conductivity of salts is one of the main problems in implementing latent heat storage. In this project, the authors intend to develop a fundamental solution to this problem using chemically bonded metals with salts. These are known as metal-salt solutions. To fit the main parameters of new phase change materials to the requirements of thermal energy storage, a wide variety of possible combinations should be considered. CALPHAD modelling is used together with thermal analysis for the development of a consistent thermodynamic database including chloride salts (Li, Na, K, Mg, Ca // Cl) and corresponding metals (Li, Na, K, Mg, Ca). The results of the study of quasibinary and multicomponent metal-salt (eg Mg-KCl and Ca-KCl) systems as well as the selection of suitable crucible materials and challenges by studying of these systems will be discussed.

Aug 21, 2024

By N N. Viswanathan, D Kumar, S Kumar

In secondary steelmaking, calcium treatment is practised to modify the solid alumina or spinel inclusions into liquid or partially liquid calcium aluminates. It has been seen that the dissolved calcium reacts with sulfur or oxygen present in the steel to form CaS or CaO type of transient inclusions. Post-calcium treatment these transient inclusions further react with pre-existing alumina or spinel inclusions and modify them. In addition, direct modification of pre-existing inclusions is also reported in the literature. In the present study, laboratory-scale induction furnace-based experiments are carried out to melt electrolytic iron in an alumina crucible followed by deoxidation with aluminium. The CaS-based composite material, prepared in-house, is added after the aluminium deoxidation to study the stability of CaS at the steelmaking temperature. Multiple steel samples were also taken to track the dissociation of CaS by means of sulfur pick-up in steel. Additionally, inclusion analysis of these steel samples was also performed to track changes in the chemical composition of inclusions in response to CaS addition. It has been seen that the CaS dissociates leading to a gradual pick-up of sulfur in steel. The scanning electron microscope – energy dispersive X-ray spectroscopy (SEM-EDS) analysis reveals that the alumina crucible and floated alumina inclusions are modified into calcium aluminates and the extent of modification depends on the contact time of CaS with the two sources of alumina mentioned earlier. However, the modification of alumina inclusions in the bulk steel did not occur during these experiments.

Jun 19, 2024

Forty years ago Dr Pierre M Gy, a metallurgist, introduced variography as applied to monitoring a process. Consequently, his followers used the variogram to elaborate meaningful process control charts, especially since 1993. The name æChronostatisticsÆ was suggested several times by Gy as a logical name for this new science. The intent was to draw a parallel between the variogram identifying the variability components affecting a process parameter as a function of time, and the variogram used in geostatistics identifying the variability components of a given mineral content as a function of space. Heterogeneity problems encountered have indeed strong similarities. However, there is a fundamental difference. The variogram used in geostatistics is often stationary within a given type of mineralisation. While investigating a dynamic process through Chronostatistics, there is no such thing as a stationary variogram. Still, the evolving variogram provides essential information about subtle, often overlooked process difficulties. Chronostatistics is especially useful for management to take advantage of existing data that are often a forgotten source of valuable information to pinpoint recurring structural problems. The superiority of Chronostatistics over conventional statistical process control approaches is that it links observations to the inherent heterogeneity of materials under investigation, therefore to the sampling theory. Chronostatistics is like opening a new world to the metallurgist, making the process variability speak in a more comprehensive and in-depth way. Several case studies are presented to demonstrate the potency of this new science. For each of them, observations lead to solutions for continuous process improvement, therefore attractive economic opportunities. The philosophy is this: if a control chart shows a process is out of control, it must also suggest logical and pragmatic directions for solutions. The intent of this presentation is to vastly expand on these valuable, almost forgotten ideas.

Jan 1, 2006

This paper reviews the various processes successfully in operation to treat refractory gold ores and describes in detail the alkaline pressure oxidation circuit operating at the Barrick Mercur Mine, Utah, U.S.A., on car- bonaceous/sulphide refractory ore and the acidic pressure oxidation circuit operating at the Barrick Goldstrike Mine, near Carlin, Nevada, U.S.A., on sulphide refractory ore. The autoclave process is important to Barrick for the extraction of gold. The Company has operated successfully a 750 ton per day unit at its Mercur property for the past two years and more recently has commissioned a 1500 ton per day unit at Goldstrike. The paper presents data relative to operating costs, materials of construc- tion for autoclaves and peripheral equipment, reagent requirements, and changes required during commissioning for both autoclave systems.

Jan 1, 1991

By Mackenzie W. R, Harding C. G

The Islamic Republic of Mauritania is a large country of over 1 000 000 square kilometres situated on the Atlantic coast of north-west Africa. It is bounded to the north by Western Sahara and Algeria, to the east by Mali, and to the south by Mali and Senegal. With the exception of a narrow strip in the south along the Senegal River valley, the country lies entirely within the Sahara. The north of the country is largely devoid of vegetation, and it is estimated that 90 per cent of the population of 2.1 million people live in the southern quarter of the country. From about the turn of the century, Mauritania was ruled by the French from Dakar in Senegal and, until 1960 when it obtained independence from the French, Mauritania did not have a capital. Today, the capital is Nouakchott, home to an estimated 600 000 Moors of mixed Arab, Berber and African descent. After independence in 1960, disputes over Spanish Sahara to the north led to a military coup in 1978 and it was not until 1991 that a democratic constitution was adopted. The new constitution declares Mauritania to be an `Islamic, African, and Arab Republic.' It provides for an executive president, elected for a six-year term, and for a bicameral legislature, consisting of a national assembly and a senate. The first presidential and legislative elections were held in 1992 under United Nations' supervision. Mauritania's economy is predominantly pastoral, and the country depends heavily on foreign aid. Its principal export industries are iron ore mining (about ten million tonnes per annum from mines near Fderik in the north) and fishing. Mines d'Or d'Akjoujt SA (MORAK), a company in which General Gold Resources NL (GGR) has 42.5 per cent equity, produces over 50 000 ounces of gold per annum, which represents the third largest export industry in the country.

Jan 1, 1996

By E Jak, P Hayes, J Chen

The paper provides an overview of the various analytical and microanalytical techniques currently in use to characterise the outcomes of pyrometallurgical processes, examining the advantages and limitations of these approaches. Specific focus with be given to quantitative microanalysis techniques including electron probe microanalysis and laser ablation, covering general principles, capabilities and limitations and recent development to address specific challenges associated with analysing molten slag, matte, and alloys, highlighting the necessity of embracing the application of these and other innovative analytical methodologies.

Jun 19, 2024

By R Dimitrakopoulos, K Kawahata, L Montiel

A method that optimises mining complexes that are comprised of multiple processing destinations, open pits and underground operations is presented. Mining, blending, processing and transportation decision variables are simultaneously optimised while accounting for geological uncertainty. The method uses a simulated annealing algorithm at different decision levels to generate a stochastic-based extraction sequence and processing policies. A case study shows its ability to generate a higher net present value while facing a reduced amount of risk when compared to traditional optimisation methods.CITATION:Montiel, L, Dimitrakopoulos, R and Kawahata, K, 2014. Globally optimising open pit and underground mining operations under geological uncertainty, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 201–212 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G R. Power

A useful way to assess potential productivity of SLC mines is by quantifying tonnes/drawpoint/day to be extracted from the mine. However limited industry information has been published to help mines benchmark this number. This paper assesses industry data which can be used to support estimates of potential productivity from new mines based on tonnes/drawpoint/day. The information used has been extracted from historical production schedules which indicate what was achieved, rather than what was planned. It has been assessed using an algorithm created for the purpose and is presented with discussion of varying definitions of active drawpoints, analysis of the data and inquiry into some of the underlying contributing factors.

Mar 15, 2021

By Terlich R. E, Finlayson J. M

A combination of high virgin rock temperatures, deep workings and extensive utilisation of heavy diesel equipment has presented North Mine (A Division of North Broken Hill Limited) with challenging ventilation problems. These problems have been addressed in a variety of ways which include in the order of 6000 kM of underground refrigeration. The future of North Mine depends on the successful development and extraction of ore in excess of 1100 m below the shaft collar using mechanised cut and fill mining. The success of this will depend on the installation of a complex chilled water reticulation circuit in this area. This will involve planning and constriction of a number of large dams, installation of pups and turbines, and the successful commissioning of several large water to air heat exchangers.

Jan 1, 1988

A flow sheet has been developed to treat a high tonnage highly preg-robbing gold ore. The ore is low grade and fine grained with a high proportion of very fi ne free gold. The key components of the flow sheet include gravity, flotation, intensive cyanidation with direct electrowinning, and carbon-in-leach of the flotation concentrate. The circuit produces a low overall mass pull to concentrate allowing economic intensive treatment of large tonnage low-grade material. Efficient recovery of fine gravity gold using a Falcon concentrator in both the milling and flotation circuits, and subsequent intensive cyanidation in a Gekko InLine Leach Reactor (ILR) is critical to the process with over 70 per cent gold recovery expected in this circuit. Grind size control was also found to be important in controlling the activity of the preg-robbers in the carbon in leach circuit and also in the solid liquid separation performance. Tests at the large-scale demonstration plant have been conducted to demonstrate the effectiveness of this flow sheet. A large low-grade deposit is currently under development with the aim of developing a 10 Mt/a treatment plant with the subsequent addition of equivalent sized process lines in multiples of 10 Mt/a. The economic development of this orebody is critically dependant on understanding and exploiting the properties of the ore. In particular it is critical to minimise the effect of preg-robbers by recovering free gold with Falcon concentrators and InLine Leach Reactors. Recovery of the remaining gold by flotation into a small mass yield allows this fraction of gold to be treated by CIL leaching utilising high carbon levels. It is critical is to ensure operation at the optimal grind size to maximise liberation of the free gold and minimise pregrobber activity. The ore has been identified as preg-robbing with low recoveries obtained if treated using conventional cyanidation and carbon absorption. The mineralogy consists of predominantly fi ne grained free gold with minor sulfides including pyrite and arsenopyrite. With conventional cyanide leaching in the absence of carbon, gold recovery is less than 50 per cent. Direct cyanide leaching of the ore in the presence of activated carbon results in an improved but still uneconomic gold recovery. The gravity recoverable gold (GRG - as defined by Andre La Plante) content of the ore has been measured to be 70 per cent to 85 per cent in various tests with liberation grind size of approximately 106 ¦m. This indicates gold is predominantly free and suitable for recovery by batch centrifugal concentrators into a low mass yield. This property of the ore presents the opportunity to maximise the recovery of gold by separating it from the majority of the preg-robbers prior to leaching. Due to the very fine gold particle sizes and the necessity to maximise recovery of this fine fraction Falcon concentrators were selected for the duty, with their proven high recoveries at very fine gold sizes. The gravity recovery in the milling circuit is designed to be in the range 55 to 65 per cent. This has been achieved in the existing pilot plant using a Falcon operating on ball mill discharge within the mill recirculating load. Intensive leaching in an InLine Leach Reactor is essential to recover the gold from the gravity concentrates. Tabling is not a preferred option since recovery is lower than intensive cyanidation and any gold losses to table tails will report to CIL where recovery is reduced by the presence of preg-robbers. Furthermore, tabling recovery from the gravity concentrates is particularly poor due to the fine particle size of the free gold. ILR recoveries of 98 per cent were demonstrated in the pilot plant using an ILR100BA and leach conditions were investigated in the lab using pilot plant generated Falcon concentrate. Recovery of gold from the pregnant solution was achieved with direct electrowinning at pilot and efficiency and sizing parameters were determined at lab scale. To further increase free gold recovery Falcon concentrators will be installed in the flotation circuit. Location of the Falcons in the circuit is not finalised but installation on the rougher concentrate stream is favoured since it will allow multiple pass recovery. This is expected to recovery a further ten to 20 per cent of the gold, as indicated by lab tests on pilot plant generated material. The gravity concentrate from the flotation circuit will also be leached using InLine Leach Reactors. Initial intensive cyanidation tests carried out on lab generated flotation concentrates indicated higher recoveries than CIL can be obtained even though the concentrates contain significant levels of preg-robbing material. This can be explained by the high cyanide, high pH leaching conditions used in the ILR which alters the absorption equilibrium of the preg-robbers. Further optimisation of the leach conditions will be undertaken once more concentrate becomes available. Recovery of the remaining gold content is achieved by flotation into a small mass yield, however the preg-robbers are also recovered into this concentrate. Due to the presence of the preg-robbers gold leaching must be carried out in the presence of high levels of activated carbon in a CIL system. The recovery has been shown to be strongly dependant on the carbon loading and the concentrate particle size. The carbon competes against the preg-robbers for dissolved gold while excessive grinding increases the surface area and activity of the preg-robbers. This has been demonstrated in test work however the economic optimum leaching conditions and carbon loading have yet to be determined. The grind size is critical to the economics of the project, not only due to its effect on gold recovery but also due to its effect on the major operating and capital costs at both the front and back end of the process. It is critical to grind enough to obtain both gravity free gold and flotation liberation at low mass yields however over-grinding results in large increases in mill size and power at the front end and filtration or thickening costs at the tails. Because these unit operations treat essentially all the plant feed even small changes can result in major impacts on project economics. The viability of this project is greatly enhanced by the high recovery of gold into a small mass yield. In particular the production and intensive leaching of the free gold gravity concentrates will allow over 70 per cent of the gold to be recovered efficiently with minimal impact from preg-robbers. By using flotation the mass of the remaining fine preg-robber contaminated material, to be leached in CIL, is greatly reduced allowing this difficult material to be economically treated. This is an ABSTRACT ONLY. No paper was prepared for this presentation. 

Aug 1, 2010

By R Dimitrakopoulos, R Senécal

This paper presents a metaheuristic solution to the optimisation of open pit long-term production scheduling with a stockpile and geological uncertainty. The optimisation formulation is a two-stage stochastic integer programming (SIP) model that determines the optimal mining sequence that maximises the total discounted cash flow, while penalising for high deviations from production targets. A parallel implementation of Tabu Search is proposed to accelerate the solution of the SIP formulation and take full advantage of multicore computer processing. Different variants of the proposed algorithm are applied to a case study to assess the performance of the parallel approach. The proposed algorithm and variants are benchmarked using linear relaxation of the complete problem to determine robustness and provide a better overview of the related performance. The results show a net improvement over the sequential solution, and the new proposal seems to be promising when working with a large-scale data set.CITATION:Senécal, R and Dimitrakopoulos, R, 2014. Parallel implementation of a Tabu search procedure for stochastic mine scheduling, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 405–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By N Madani

Linear interpolation of geo-related variables is important to different aspects of mining engineering such as long and short-term mine planning. The ore deposit description attained from spatial modeling of blast hole datasets has been widely taken into account, particularly, for short-term mine design and grade control, so as to define the ultimate destination of a mined block. It is approved in practice that making the wrong decision leads to losing a huge amount of money for choosing the destination of a mined block. In the case of complex ore deposits, the issue of estimation of variables in the region is questionable and somehow tedious. Due to this fact, modeling those complications in the co-spatial behavior of the grades in multi-element deposits prompts one to employ enhanced geostatistical techniques. Traditional approaches of this purpose such as polygon, inverse distance weighted and even (co)-kriging approaches, are incapable of reproducing those complexities such as non-linearity, heteroscedasticity and geological constraint that frequently exist among the variables of interest in those deposits. Another difficulty in employing those linear interpolations in grade estimation is smoothing effect, in which the estimated grades are over and under estimated. CITATION: Madani, N, 2018. 3D estimation of variables with complexity in cross-correlation structures, in Proceedings Complex Orebodies Conference 2018, pp 49–52 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

The paper describes the preparation of new rail guides, removing existing rails, and replacing with new rails in a vertical winding shaft.INTRODUCTIONThe general practice in coal winding shafts is the use of two cages, with one or more decks in which men and materials are raised or lowered. Winding speeds vary according to depth, the type of winding gear, and whether winding is done in downcast or upcast shafts. Each cage occupies a position between the centre and side of the shaft, with a clearance depending on the type of guides used. The function of the guides is to keep the cage in position throughout the entire depth of the shaft. There are three types of guides, two of which are in general use.1. Selected wood of about 6 in. square section, fixed to the side of buntons.2. Solid strand steel made up similarly to that of an ordinary wire rope, suspended from the head frame with weights attached to the lower end.3. Standard T-rail sections fixed to end or side buntons. Of the three types, 2 and 3 are in general use. The type used in the particular case, the subject of this paper, is T-rails of the standard section used in railway work.GENERAL DESCRIPTION OF SHAFTDetails of the shaft are as follow: Diameter of shaft: 22 ft. inside lining.Depth of shaft: 900 ft., including sump.Concrete lined throughout.VENTILATIONThe ventilation shaft is used for the upcast, through which all vitiated air passes to the main ventilation fan. Quantity of air passing up the shaft is 400,000 cu. ft. per minute. The air is highly saturated during the summer weather and slightly less...

Jan 1, 1947

By G Reynolds, L Lu

Queensland Pacific Metals (QPM) is developing its flagship Townsville Energy Chemicals Hub (TECH) facility to produce nickel and cobalt sulfates from imported high-grade nickel laterite ore for nickel-cobalt-aluminium and nickel-cobalt-manganese Li-ion batteries. The TECH facility is expected to use a patented leaching, recovery and recycling process called the DNi Process™. It uses the nitric acid leaching process for extracting nickel, cobalt and other valuable metals from laterite ore. Apart from the nickel and cobalt sulfates, the TECH Project will also produce high purity alumina, hematite (~640 ktpa) and other by-products. The hematite by-product precipitated from the DNi Process™ (hematite precipitate hereafter), is high in Fe and particularly low in impurities. QPM is working to identify potential applications for these high-purity by-products to generate additional revenue and to achieve its zero-waste ambition. As such, QPM has engaged CSIRO to evaluate various agglomeration options to produce low-cost, hematitic products suitable as ironmaking feed materials. This paper will first reveal the unique characteristics of the hematite precipitate arising from the TECH Project and then examine the sintering and pelletising processes for preparing the hematite precipitate as an ironmaking feed.

Sep 18, 2023

By G Harbort, V Lawson

Mount Isa Mines Limited operates one of the worldÆs largest underground mines in North West Queensland. ItÆs mining and smelting complex produces copper anode, crude lead bullion (containing silver), and zinc concentrate. Copper is recovered in the Copper Concentrator from chalcopyrite ore, converter smelter slag and rotary holding furnace (RHF) slag via grinding and flotation operations. During 2002 a project to optimise cleaner circuit capacity was commenced. Its aims were to minimise copper losses and minimise slag/chalcopyrite cross contamination by reconfiguring existing flotation equipment and the addition of new flotation capacity. To minimise cross contamination a Jameson Cell was installed and dedicated to cleaning of slag concentrates, which had formerly been conducted by three flotation columns operating in series. The flotation columns were re-configured to operate in parallel and dedicated to upgrading chalcopyrite concentrate. In addition a Jameson Cell was installed to reject entrained copper from a prefloat concentrate consisting of talc and carbonaceous pyrite. This paper discusses the logic behind the cleaner circuit expansion, recent test work relating to the Jameson Cell and the installation and commissioning phases. Difficulties relating to the commissioning are reviewed and the solutions to problems are highlighted. The benefits the reconfigured circuit has provided to Mount Isa Mines are also discussed.

Jan 1, 2003