Search Documents

In December 1997, a series of new environmental legislation was enacted including:ò Environmental Planning andAssessmentAmendmentAct 1997; ò Contaminated Land ManagementAct 1997;ò Protection of the Environment (Operations) Act 1997; ò Native Vegetation Conservation Act 1997; andò Pollution Control (Load Based Licensing) Act 1997.These new Acts will have varying degrees of impact on the coal mining industry in New South Wales when they commence later this year.

Jan 1, 1998

Routine, in-pit geological mapping of highwall at Central Queensland Coal Associates (C.O.C.A.) deep strip mines has proved too slow for the increasingly greater highwall lengths which require mapping. This realiz- ation has encouraged the search for faster mapping methods and after trial of ground photographic methods has resulted in the adoption of interpretive mapping off stereo cover, oblique -- aerial photography. This entails using a Cessna 182 light aircraft flying at its slowest speed, the aerial meth- od finally employed consisting of two Vinten, air reconnaissance cameras mounted in parallel and simultaneously taking both colour and black and white photographs of the mine high- wall. The respective 1:500 scale enlargements produced from the 70mm format films combine to present the sharpest resolution attainable under the field conditions pertaining and such information on weathered material as only colour photography can fully render. Total costs for the aerial photography method are estimated to be about the same as those for conventional in-pit mapping. Whilst total costs are comparable, geo- logist's time for mapping a 10 km. length is reduced to less than half that for in-pit mapping (for Stage 1, fully accurate mapping) and accuracy and detail are greatly improved. A permanent, accurate record of overburden

Jan 1, 1981

By R Berry

This paper looks at two ways to estimate the bulk mineralogy of the rocks for assay intervals. The aim is to find an efficient indicator of the most common minerals in the rock. Phase (modal) analysis has traditionally been done using visual methods such as point counting and image analysis. A modern version of this process is the X-ray point counting routine using the SEM-EDS based software. These methods are too slow and expensive for routine analysis of bulk sample mineralogy at the normal assay spacing.Two sources of data were considered that provide information that can be used to determine the mineral abundance in assay samples. The most widely applied method is (semi-) quantitative X-ray diffraction (QXRD). The QXRD method is most applicable to major minerals and has limited application to minerals at low abundance. The nominal detection limit is 0.5 per cent. Values below five per cent have large errors. A second, less common, method is calculation of mineralogy from chemical assay data. Conversion of chemical analyses to mineralogical analyses depends on the unique chemical composition of each mineral. Elements only found in one mineral are easily accounted for, but many compositions are ambiguous. Deciding on the actual mineralogy is not simple. Recalculation of mineral mode from chemical analyses is more accurate than QXRD when the correct minerals, and mineral compositions, are known.Where only a few QXRD analyses are available they can be used to setup a protocol for calculation of mineralogy from assay data. Linear programming works well in this environment. The best results are obtained when both H2O and CO2 are directly measured. Loss-on-ignition (LOI) should be included if these are not available.Where both QXRD and chemical analysis are available for all samples, the best results are obtained using the least squared method to merge the data sets assuming QXRD has much higher analytical errors than chemical assays. The combined method provides more robust results because the high abundance minerals are controlled by the QXRD measurements while the chemical assays improve the precision for low abundance minerals

Sep 5, 2011

By Moorrees C

Carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite yields a magnesium bicarbonate leachate with a substantial soluble iron concentration. The iron concentration depends upon the leaching conditions (particularly time, temperature and pulp density) but is generally in the range 0.005-0.5 g/litre. If this soluble iron is not removed prior to the precipitation of the magnesium as a hydrated carbonate, then this product will be contaminated by the iron, and will not yield a final product (high-purity magnesia) that meets specifications.The soluble iron content of the magnesium bicarbonate leachate can be reduced to an acceptable level by addition of solid aluminium sulphate either during carbonic acid, leaching of the crude calcine or to the clarified leachate. Chemical analysis and X-ray diffraction revealed that the iron is precipitated as an iron-containing hydrotalcite-type compound, [Mg6(Al,Fe)2(OH)16]CO3.4H2O. The actual composition of the precipitate depends on the amount of aluminium sulphate added and the precipitation technique used. Because precipitation of iron in this manner also results in reduced magnesium recovery from the leachates, It WIll be necessary to develop methods for recovering the magnesium component of the precipitates.

Jan 1, 1984

By M Hino, Y Sasaki

Sustainable handling of municipal waste and sewage sludge has an important goal to recycle resources without supply of harmful substances to humans or the environment. The gasification mechanism of phosphorus from municipal waste and sewage sludge during the incineration process has been investigated to develop a phosphorus recovery system. Quadrupole mass spectrometer coupled to an electric furnace is applied to study the vaporisation behaviour of phosphorous gas phases from municipal solid waste (MSW) incinerator ash of sludge during solid-state reduction by carbon. Measurements are carried out in vacuum conditions of 2 x 10-6 Torrs and furnace temperature range 573 - 1773 K, at a heating rate of 7.22 K/minute. It has been found that most of the phosphorus is vaporised as PO2, P2 and P4, in agreement with thermodynamic estimation despite a shift in the temperature regimes.

Jan 1, 2006

By K Barbosa, G Wilkie, F Reyes, V Jokovic, C Evans

The idea behind Grade Engineering is to exploit the natural heterogeneity of an orebody (spatial, temporal) in order to divert low-value waste out of the mining value chain. Essentially, this involves rejecting material at relatively coarse particle sizes (10 mm to 200 mm). However, lack of knowledge about the inherent particle grade distributions in these coarse particle size ranges limits the opportunities for optimisation. Particle grade distributions are essential for quantifying and modelling gangue liberation and yield curves. These curves can then be used to predict the mass and value flows that will go towards the accept and the reject streams. Particle grade distribution information for particles coarser than 10 mm can be collected based on chemical assays of sufficient number of individual particles. However, for smaller particles (1 mm to 9 mm), a significantly larger number of particles is required for assays. Moreover, in some cases, the mass of individual particles is smaller than the minimum mass required for chemical assaying. Also, other quantification techniques such as automated mineralogy, eg Mineral Liberation Analysis (MLA), require extended measurement times to analyse statistically representative numbers of particles at these size ranges. This work investigates the use of 3D X-ray microtomography to fill this quantification gap at these size ranges (1 mm to 9 mm). In-house image processing algorithms are used to estimate the mineral/metal content in each particle. Particle grade distributions, as well as density distributions, are thus produced without a minimum mass requirement and with each scan providing information about tens to hundreds of particles at a time. Mineralogical data from MLA analysis, of finer size ranges, is used to inform X-ray microtomography, so a simpler 3D mineral map can be obtained using the image intensity. Chemical assay information of the scanned samples is used to validate and correct the mineral phase segmentation.

Aug 24, 2022

Uranium minerals were found in Australia as early as 1869, but it was not until the 1940's that a search specifically for uranium was begun. Instrument types and techniques used in early exploration are still used today, but have been developed into more sophisticated and portable types. Recent improvements in exploration have been the introduction of the gamma ray spectrometer, radon sampling and geochemical surveys. The environments of presently defined uranium deposits are predominantly sedimentary. Known deposits in igneous environments are usually small. The size of targets which are likely to provide economic deposits is of the order of 10,000 tons U308, producible at a cost of less than $10 per pound. Such targets are most likely to be in Precambrian sediments or in granitic masses. Recent exploration in Australia has included investigation of Precambrian sediments, Precambrian and Palaeozoic granites, Mesozoic and Tertiary sediments, Precambrian volcanic rocks and brecciated masses of unknown age. The origin and method of emplacement of uranium in these environments is not well known but there are indications that syngenetic sedimentary processes are important, and volcanic rocks may make a major contribution to the supply of uranium.

Jan 1, 1970

The three papers reviewed here consider different problems of mine management. Comparison of two of the papers demonstrates a marked contrast between the old and the new, in terms of mine management and impacts. The third paper discusses post-mining rehabilitation. The paper "The impact of a derelict base metal mine on the aquatic environment", by Brooks and Mclveen contrasts strongly with the paper "Narbarlek Uranium Mine design, construction, operation monitoring and decommissioning of the water management system" by McLoughlin, Grounds and Weatherhead. Brooks and Mclveen detail the contamination emanating today from the Conrad Mine in New South Wales which was mainly operated for 15 years at the turn of the century and later for 7 years in the 1950's. The mine was apparently developed over the years on an intermittent, ad hoc basis with no regard to contamination management, resulting Ti significant contamination persisting through time. This type of mining development is the antithesis to the type of planned mining and management operation which was carried out in Arnhem Land at Narbalek, and which apparently resulted in no uncontrolled contaminant release and successful decommissioning of the mine.

Jan 1, 1988

Interest in mining narrow, vein-type ones has increased world-wide during the last few years despite the fact that prices of metals have not risen in proportion as production costs of mining, such as labour and energy.In many mines, where narrow ones are mined, the mining technique and equipment used have been poorly mechanized. The mining methods have been cut-and-fill or shrinkage stoping. Pneumatic jack-legs have been used for drilling and slushers have been used for loading.The methods that have been used can be called the "first-generation" methods.Work has been very hard for miners. It has been dangerous and exhausting.Production volumes of mines, and a s a result of that, also profits have been low.

Jan 1, 1990

By K Kinnunen

A strong correlation between the reduction degradation index (RDI) of production sinter and the titanium content of the sinter mix was identified at the Ruukki sintering plant between 2000 and 2004. The titanium distribution in different mineral phases was studied using samples from pot sintering tests. Titanium additions were made using two different materials: rutile and crushed titanium-bearing haematite pellets. While both titanium additions clearly increased the RDI, titanium seemed to favour secondary haematite. The study focused on the effect of titanium in haematite, because haematite is reduced to magnetite in the RDI test. During the haematite-magnetite reduction, reduction degradation was observed. To increase accuracy, the phenomenon was investigated first by sintering and then reducing synthetic minerals under controlled laboratory conditions at the University of Oulu. The effect of titanium oxide in solid solution in magnetite on the magnetite to haematite transformation rate was studied first in order to simulate the final stage of the sintering process. In other experiments, haematite samples doped with 0.5, 2.0 and 5.0 wt per cent titanium oxide were studied using thermogravimetry under a controlled gas atmosphere (CO/CO2/H2/N2). Sintered samples were reduced using the same gas composition as in the RDI test. Polished sections for optical microscopy and SEM-EDS analysis were prepared from both reduced and oxidised samples and unreduced sintered samples. The titanium oxide content of haematite had a clear effect on reduction degradation of the samples. Furthermore, increasing titanium oxide content in solid solution in magnetite radically accelerated the oxidation rate. Similar observations regarding the effects of titanium have been reported earlier, but this was the first time the effect of very small additions of titanium were shown to deteriorate blast furnace burden quality and a reason suggested behind the process.

Jan 1, 2007

I began my interest in sample preparation when I joined the Institute of Nuclear Sciences in 1962. I worked in the fields of rock dating and stable isotope geochemistry. Preparing a sample could take several days and the analysis took another day or more, so great care was taken with each sample. In 1968 I changed to mineral exploration analysis and was surprised to find that there was much less care in how a sample was taken and prepared. Virtually every sample was processed in the same way. In the use of ring and puck mills, Australia and New Zealand were among the world leaders. It took another ten years before labs in North America changed over from disc mills. In 1975, my partner and I divided our business into two parts. He took the laboratory into his consulting laboratory business and I took the small business that we had started, making ring and puck mills. For the next six years I was RocklabsÆs only employee. In the 1980s and 1990s, sampling specialists like Francis Pitard and Dominique Francois-Bongarcon began to make a difference in the understanding of what constitutes good sampling and preparation practice. They and others took courses on the new concepts of Sampling Theory, as developed by Pierre Gy. The desire for better procedures lead to the development of new machines, including the big bowl pulverisers from Australia, jaw crushers that could crush finely like our Boyd Crusher, rotating dividers of new designs and flow-through ring and puck mills. Other machines did not fare so well, including rolls crushers, cone crushers and hammer mills.

Jan 1, 2008

By Ellis CG

The N.S.W. Department of Mineral Resources commissioned its first Mobile Gas Laboratory in 1973.Although originally intended for diesel exhaust analysis, it has been progress- ively made more suitable for mine air analysis. Currently there are two upgraded units in operation. These laboratories have been used at the scenes of four mine fires, two mine explosions and three recovery operations. The authors' experience jointly covers all of these incidents. In this paper they recount the role of the Mobile Laboratory in each incident - including the difficulties encountered - and trace the development of these units to their present state. Future improvements are foreshadowed, and some comments offered concerning the likely future role of these vehicles in mine Emergencies.

Jan 1, 1981

In 1985 a 2.5-tonne top blown rotary converter was installed in the silver refinery at Cominco's Trail Operation to carry out the final cupellation of burndown metal to Dore metal. The furnace is fired with an oxygen-natural gas lance which is capable of achieving a variety of furnace conditions, varying from reducing to highly oxidizing. Reaction rates are about 4 times greater than using conventional cupel furnaces. The faster reaction rates improve productivity and reduce in-process precious metal tie-up. The furnace is also used to reduce litharge slag for bismuth recovery.

Jan 1, 1989

By Carroll D. A

The mining and minerals industry has had and will undoubtedly continue to have a considerable impact on the development of this State. For the first 60 years of its history the colony of Western Australia made slow progress; its population in 1889 being only 43,000. However, as a-result of discovering gold at Coolgardie and Kalgoorlie the Eastern Goldfields alone had a population of 25,000 by 1897. The income generated by the gold mining industry allowed the Premier of the day, Sir John Forrest, and his Government to support the proposal put forward by the State's Engineer in Chief, C.Y. O'Connor, to construct a pipeline to carry water from the Darling Ranges to Kalgoorlie ; a distance of 600 kilometres. The demand for people knowledgeable in the science and art of mineral exploitation also prompted the State Government to establish a School of Mines in the Goldfields in 1902, where it has remained ever since. The gold mines of this region have been a major source of employment for over 70 years and there is no doubt of the fact that their continued prosperity minimised the effect of the world recession on Western Australia in the 1930's.

Jan 1, 1979

The current quantity of rejects from coal beneficiation in Australia represents 20 to 25% of raw black coal production. Approximately 80% of the rejects are derived from coarse processing for particles in the 200mm to 0.5mm size range. The safe and enviornmentally acceptable storage of coarse coal rejects is of interest to coal mining companies. Additional public benefit would be derived from the utilisation of a waste product as a source of fill material for civil and mining engineering applications. BHP Engineering has taken a leading role in the design for storage and utilisation of coarse rejects from two mines associated with the Broken Hill Proprietary Conipany Ltd. The tailings dam at Stockton Borehole Colliery (N.S.W.) is to be raised and a study by BHP Engineering has shown that coarse rejects are suitable for the formation of the supporting embankment surrounding a compacted clay core. Transportation and storage of coarse rejects at the Thiess Dampier Mitsui Riverside Mine (Moranbah, Qld) is achieved by a conveyor leading directly from the coal preparation plant to a discharge stacker on the crest of the rejects stockpile. Production of coarse rejects was higher than anticipated for the initial dump design. BHP Engineering has completed a review of dump design with emphasis on safe operating conditions for the conveyors and stacker system. Data on the geotechnical properties of coarse rejects from Australian coal mines are presented. Coarse coal rejects are a material which should not be considered as waste, but as a potentially valuable resource for many future applications. Appropriate engineering design for the storage and utilisation of coarse rejects would result in an improved environment and economic benefits for the Community.

Jan 1, 1987

As previously advised, two of the raw materials for Wilsons Portland Cement are cement rock and limestone, both of which are quarried by the company. We now wish to give you a brief outline of these operations. The major material, cement rock, is obtained for our Portland Quarry at Tikorangi Hill, which is one mile west of the Works and a familiar landmark to travellers on state Highway 1. The geological structure of this deposit is involved, having intensive and irregular earth movements interpreted as large scale slumps where older rocks overlay younger rocks - numerous folds, faults and overthrusts are clearly visible.

Jan 1, 1978

By Morrison R. D, Davis J. J, Fraser B, Kojovic T

1991 saw the completion of a three-year $1.1 million research and development program in mineral sands beneficiation, funded in two associated projects by the Australian mineral sands industry through AMIRA, and carried out by the Julius Kruttschnitt Mineral Research Centre. It is believed to be the largest R&D project in mineral sands ever conducted by a university research group. It covered dry plant operation, and delivered several products to the industrial sponsors, including: ò A detailed characterisation of the radiation properties, mineralogy and size distribution of inhaleable dust arising in dry plants. ò New process models of magnetic and electrostatic separators. ò New on-line instruments for elemental assay (in association with AMDEL) and bulk conductivity measurements of dry process streams. ò Demonstration and evaluation of the Magstream magnetohydrostatic separation technology.

Jan 1, 1992

By P Hayes, B Zhao

A range of materials are treated in zinc fuming processes to recover metal values and produce benign slag waste products. The selection of the optimum process conditions in these various technologies can be greatly assisted by the use of a chemical thermodynamic model of the system. In this paper the effects of slag chemistry on the liquidus temperatures, subliquidus phase equilibria and thermodynamic properties are described by a FACT model of the ZnO-PbO-FeO-Fe2O3-CaO-SiO2 system. In addition new experimental data on the effect of Al2O3 on the liquidus are presented. The implications of these findings for plant practice are discussed.

Jan 1, 2000

By A S. Bamber

Mining is the oldest industrial practice on the planet with a history dating back over 3000 years. Since the early iron age ores have been extracted for use in a variety of contexts by humankind, from domestic to military, transport and more recently for complex industrial applications. Mineral exploration and extraction has evolved from the early exploitation of primary metal occurrences in relatively small quantities such as iron, gold, coal and copper, to the bulk mining and extraction of highly complex polymetallic oxides and sulfides today. Since the industrial revolution, mining practice has evolved substantially to support an increasing range and quantity of required metals and to accommodate the increasing scarcity of high-quality sources of these metals. A common response to the increasing scarcity of mineral resources has been to expand production through simple economies of scale, thus diluting fixed costs. This approach, however, is increasingly ineffective in the face of current trends, that include increasingly complex mineralogy, increasing pressure on environmental footprint - energy in particular, and increasing scarcity of capital for the construction of presently popular æmega-minesÆ. This paper examines historical trends and current practice in mineral exploitation in the light of the current global revolution in social, environmental and economic values as the projects move towards a vastly different topology for the industry for continued success in years to come.CITATION:Bamber, A S, 2012. The mining industry needs to be shaken and stirred, in Proceedings Narrow Vein Mining 2012 , pp 3-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

By Chen J, Sun ZY

The present paper gives the design of a new HGMS for magnetic separation of sulphides. The main characteristics of this HGMS are using iron-cladding saddle-shaped magnetic coil for instead of the ordinary magnet, and combining reciprocal-linear motion with vibration to actuate the separation box, and the magnetic field intensity is high up to 2T as well. For improving the magnet system design, a modified finite element method is used to calculate the distribution of magnetic field intensity of separation space of the magnetic coil, and accordingly the calculation results the magnetic leakage coefficient can be determined easily, thus designers apart from the empirical way. KEYWORDS: HGMS, reciprocal motion and vibration, finte element method, saddle-shaped coil.

Jan 1, 1993